User manual of super-intelligent wind and solar hybrid
Contents
1. 2 Product Parameter Model HY T2 WSII 06 NNHN 2 HY T4 WSII 06 NNHN 2 Battery parameters Applied battery voltage 24V 48V Battery protect method Reverse connection protection do not burn any components with voice prompt over voltage protection under voltage protection for street light and such kind of load Voltage at the over 29 0V 40 2V 58 0V 0 3V voltage protection point Voltage at the over voltage 27 5V 40 2V 55 0V 0 3V recovery point Voltage at the under voltage 21 0V 40 2V 42 0V 0 3V protection point Voltage at the under voltage 23 0V 40 2V 46 0V 0 3V recovery point Battery temperature compensation 5mv C 2V settable optional component Wind turbines input parameters Rated power of applied Wind 600W 24V 600W 48V turbines Rated power of the terminal 30A dc after rectification 15A dc after rectification Max input current of the terminal 40A dc after rectification 20A dc after rectification The default speed of the Wind 500 Rpm settable turbines generation with limited speed The default current of the Wind 30A settable 15A settable turbines generation with limited current Wind turbines protection method over rev protection over current protection induction lightening protection Unloading method PWM stepless high frequency soft unloading built in MPPT function Boost MPPT model automatic tracking or 5 segments curve track2. Wind turbines stall current limit control methods which makes Wind turbines not run over current avoid the damage of expensive generator caused by heating due to over current Wind turbines input MPPT generation technology boost Controller can provide automatically Wind turbines input maximum power tracking mode or the 5 segments match curve input configuration mode input rev to input current or output voltage to input current curve which makes the high efficient generation of the Wind turbines but with low speed Support multiple output mode selection This controller provides optional multiple output modes light control time control 3 4 light on in the morning PWM dimming reverse direction which can satisfy a variety of applications Statistics the cumulative generating capacity remaining power speed current temperature and other data The controller screen displays not only the current voltage power of conventional Wind turbines PV battery and the output terminal but also the cumulative generating capacity of Wind turbines and PV the remaining battery power Wind turbines speed unloading current and the temperature of controller Alarm function when terminals up When the terminals are up the controller will alarm which requires customers to use with the correct install direction avoid the possibility of damage caused by water comes into the controller when used in the open air or due to bad weather
3. wire connecting Terminals are treated with injection molding process wiring short circuit and cross will not occur more safety for customers operating Automatically alarming of battery reverse Battery input terminal will not be damaged with continuous reverse and it has buzzer alarm Avoid equipment damage and fire caused by wiring errors and better protect the battery Automatically alarming of Photovoltaic panels reverse Photovoltaic panels will not be damaged with continuous reverse and it has buzzer alarm It will not cause wiring errors especially when work at night Note reverse connection detection in the night needs manually keys intervention Continuous short circuit output protection Discharge output terminal has continuous short circuit protection and over current protection It is recovered after the abnormal excluded Avoid damage of the controller or fire caused by electrical equipment fault especially the short circuit Patented Wind turbines steady speed generation control technology Patented Wind turbines steady speed generation control method which makes the Wind turbines not run with super speed the Wind turbines can keep generation with a limited set speed even in the high winds avoid direct stop of Wind turbines with over speed caused by strong wind Greatly improve the Wind turbines generation energy and keep the safe running of the Wind turbines Patented Wind turbines stall current limit control technology Patented
4. User manual of super intelligent wind and solar hybrid controller Suitable for 600W 24V 48V Wind turbines Product model HY T2 WSII 06 NNHN 2 HY T4 WSIT 06 NNHN 2 3 1 Comprehensive introduction of products 1 1 gt t 1 Basic information Super intelligent wind solar hybrid controller is a new type of special high performance control device for new energy application which is designed on the basis of ultra high performance controller It contains many years of application experience such as waterproof dustproof salt spray wiring error wind resistance limit control of Wind turbines energy management etc it has done to ultimate no matter it applied to the charging control or street light control In order to meet variety of applications the controller adopts a hierarchical and modular structure all functions can be achieved with different functional plates according to actual application and it is convenient for rapid customization and application 2 Characteristics Waterproof Three defenses for circuit board hierarchical design even if small amount water enters it will not damage the device gt KSA RS232 communication Standard configuration RS232 communication it is easy to do the monitoring with the computer software RS485 short range wireless is optional Using a USB to RS232 members more convenient to exchange data with a computer computer with USB interface can be used Safety
5. by mode screen backlight closed About 20ma 24V system Operating mode 3M foil key operation 4 keys Working temperature humidity range environment 40 80 C 20 85 RH non condensing Protection grade IP41 Controller size L W H 175mm 148mm 84mm Net weight 1 8KG
6. ing Input current of MPPT channel 12A PV input parameters Rated input current of applied PV 550W 24V standard 1100W 48V standard 1100W 24V optional 2000W 48V optional Rated input current of terminal 15A standard 30A optional Charging voltage drop lt 0 2V PV protection methods Reverse connection protection voice prompt Unloading method Open circuit unloading Discharge the output port parameters output 2 outputs Current of each output 12A Output protection methods Over current protection 15A 30sec 18A 0 4sec short circuit protection current gt 150A Output control methods light control time control reverse output PWM output 250HZ only the 2 output has it Others Auxiliary function Monitor of air temperature inside controller temperature of unloading parts and Wind turbines MPPT components and also the monitor of control terminals installed on the inversion with voice prompt Display mode Liquid crystal LCD display Communication mode RS232 5V electrical level RS485 standard Short range wireless optional Displayed parameters Wind turbines input voltage current power generated energy rev unloading current PV input voltage current power generated energy Battery voltage charging current power total charging capacity battery status information output current power abnormal information of the 2nd output port Power consumption in stand
Download Pdf Manuals
Related Search