QSG - Vera Lite - RGB
Contents
1. NET CONNECTION Even without an internet connection you can still use Vera although you will miss out on some features that require internet like remote access and email text message notifications First power on Vera wait 2 minutes until Vera s Ready light stays on solid Vera will attempt to automatically get an IP address If you do not have a home network connect your computer directly to Vera s WAN port and give your computer a static IP of 192 168 81 2 with a netmask of 255 255 255 0 Then open a browser to http 192 168 81 1 and follow Vera s setup TROUBLESHOOTING For Technical Support contact us via email at support micasaverde com or call us at 1 702 487 9770 For online help visit the Support section on our website http micasaverde com Thank you for purchasing VeraLite by Mi Casa Verde P F i 7 v f 7 Oe Y hd Hn i d i rrn A 7 ot f F gi y 0 l f X KA A bid A i i AS y T 1 T2. micasaverde THANK YOU FOR PURCHASING VERALITE BY MI CASA VERDE TO GET STARTED Connect the network and power as labeled in the diagram below Wait up to 2 minutes for the Power Ready and Network lights to come on solid without blinking When the lights are on visit http micasaverde com setup using a web browser that is on the same home network as VeraLite If your computer and VeraLite both have internet and are both on the same network you will automatically be redirected to Vera s web page to start setting up and using VeraLite Power Ready Connect to 7 Power 7 Network sss Connect to Internet ADDING AND REMOVING Z WAVE DEVICES Generally VeraLite must be within 3 feet 1 meter to the Z Wave device you want to add or remove If it is convenient to bring the device near VeraLite you can leave VeraLite plugged in and press the button when the Power and Ready lights are on solid If it is not easy to bring the device to VeraLite then disconnect any cables from VeraLite Ensure that 4 AA batteries are properly inserted in Vera s battery compartment and press the battery button to power Vera by its batteries making Vera portable Wait up to 1 minute and when you see the Ready light start blinking you can start adding devices TO ADD A DEVICE Vera s Ready light must be blinking slowly once per second You must activate the device s inclusion
3. ocess will reset the device to its original factory default state so it can be paired to a new controller like Vera Once you have finished removing resetting devices click the button to go back into include mode At that point you can either add devices or click the button again to exit add remove mode and save your changes If the Power light does not come on check that the power adapter is plugged in and connected properly After waiting 2 minutes if the Network light does not come on it means the network cable is not properly connected If the network cable is connected Vera will test that it can reach the internet While Vera is testing the network the Network light will blink steadily After 2 minutes if the network light is doing a double blink pattern that means the internet cable is connected but Vera cannot reach the internet If the Power and Network lights come on but the Ready light does not or if the Error light is lit please contact tech support see below USING A STATIC IP If you need to assign Vera a static IP power on Vera like normal connect your computer s network port directly to Vera s WAN port Power on Vera like normal and when you see the double blink pattern set your computer to the static IP 192 168 81 2 netmask 255 255 255 0 Then open a web browser to http 192 168 81 1 and choose Vera s Setup Net amp Wi Fi option USING VERA WITHOUT AN INTER
4. or pair mode Consult the device s user manual for instructions For light switches and plugin modules this is generally done by turning the light on or off While Vera is busy adding the device the Ready light will go out and when Vera has finished added a device the Ready light will flutter rapidly for 2 seconds to let you know Once it starts blinking slowly again you can add the next device If you cannot get a device to add follow the instructions to remove or reset the device and then try to add it again Once you have finished adding a device click the button again to exit include mode and save your changes P Ap ay N y hl Dey 7 B a micasaverde TO REMOVE OR RESET A DEVICE press the button Even with new devices this reset process is often required before it will pair When the Ready light blinks quickly 4 times per second Vera is ready to remove or reset a device Activate the device s exclusion or remove mode Consult the user s manual for instructions In most cases this is exactly the same process as including the device Once Vera has reset the device the ready light will flutter rapidly for 2 seconds to let you know Once the light resumes blinking slowly you can reset the next device When you reset a device if the device has already been paired with Vera the device will be removed or unpaired If the device has been paired with another Z Wave controller before this pr
Download Pdf Manuals
Related Search