X SPOT
Contents
1. X SPOT USER S MANUAL a 4 A j j s a z a Pe Y o i N E gt A F d a E AS l i u dili o ee K SS f ki u a LUDI LIGHTING X Spot user s manual Dimensions 250 mm W x 246 mm D x 345 mm H OLudi Lighting Limited Information subject to change without notice Ludi Lighting Limited and all affiliated companies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual The Ludi logo the Ludi name and all other trademarks in this document pertaining to services or products by Ludi Lighting Limited or its affiliates and subsidiaries are trademarks owned or licensed by Ludi Lighting Limited or its affiliates or subsidiaries Safety Information gt gt D gt WARNING Read the safety precautions in this section before installing powering operating or servicing this product Warning Class 2M LED product Do not look into the beam at a distance of less than 0 5 meters 20 inches from the front surface of the product Do not view the light output with optical instruments or any device that my concentrate the beam This product is for professional use only It is not for household use This product p2. XLR pin out on fixtures does not Install a phase reversing cable between the match pins fixtures or swap pins 2 and 3 in the fixture that 2 and 3 reversed behaves erratically Light output shuts down Fixture is too hot Clean the fixture especially air vents Ensure free unexpectedly airflow around fixture Check that ambient temperature does not exceed max permitted level If problem persists contact Ludi for advice Disposing of this product Ludi products are supplied in compliance with Directive 2002 96 EC of the European Parliament and of the Council of the European Union on WEEE Waste Electrical and Electronic Equipment as amended by Directive 2003 108 EC where applicable Help preserve the environment Ensure that this product is recycled at the end of its life Your supplier can give details of local arrangements for the disposal of Ludi products Specifications Physical E AR a bn eda end AI anal ale ease OL O donja 240 mm ATAT E E o ss O aes et O wale UR rod ee PR 235 mm Hibrido acts Bt ac ede AAA 355mm X Spot user s manual Wee sus pad dai ii ss a a 7 2 kg excl brackets Dynamic Effects CO o E ES rete ee ed 7 o A O OA A DR o dC 8 ROtaLINE CODOS Las SEDES ESA prai E a A US IA a Aaa 7 FOCUS ico Motorized PRISM sas it AA ARAN EDS EAS Rotating in varied speeds Electronica E eere pita bio eee ces O 100 SMODE CTC sunitas A Sid sadia E ES AAA Electronic PAM EAS AE AA E en See ah a 630 PAU
3. fast Scroll anti clockwise slow gt fast Clear Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo Scroll clockwise slow gt fast Scroll anti clockwise slow gt fast Stop Gobo rotate clockwise slow gt fast Gobo rotate anti clockwise slow gt fast Gobo rotate in both directions Null Light on Strobe slow gt fast Stop strobing Light off Dimming dark gt bright Null Pan and tilt controlled by channel 1 5 Pan and tilt auto moving disable channel 1 5 Off Prism rotate slow gt fast 240 255 Prism 15 0 255 Focus Troubleshooting Problem Probable cause s Remedy Fixture is completely dead No power to fixture Check power and connections Fuse blown Disconnect fixture from power Check fuses and replace One or more fixtures resets Fault on data link Inspect connections and cables Correct poor correctly but responds connections Repair or replace damaged cables erratically or not at all to Data link not terminated Insert termination plug in output connector of the controller the last fixture on the link Incorrect fixture DMX addressing Check addressing on fixture and controller Check fixture is set to correct DMX mode One of the fixtures is defective and is Unplug XLR in and out connectors and connect disturbing data transmission on the them directly together to bypass one fixture at a link time until normal operation is regained Have faulty fixture serviced by Ludi service technician
4. e A O PREDADOR EDP A E RO 270 Adjustable pan tilt and effects speed Optics Dent sou CO ma tada bao mias suo aaa tarada Luminous high power emitter Color Temperature spread we eS A a Eee eae eS 5700 K Light Output Max inte color satd sia dd a Baie Ma IG SAS id 720 lux 5M Control and Programming CONMLCOLOOUIOMS 3 53 oe es DMX stand alone master slave Control resol ON cxcadtwe ia heh See A ennui aii 8 and 16 bit DNDECAA Meli admin e ER eee ae Se ee as 15 Setting and addressing Control panel with backlit LCD display Protocol apar ae USITT DMX512 1990 Stand alone programming Control panel with backlit graphic display Construction COl ea a ss aa td a ee eS Ree ZONE NKA Black HOUSINE ria sl a High impact flame retardant thermoplastic PrOTECUON PAGING as E A daa tonada IP 20 Electrical NC POWER upa ne ptas peda tees 100 240 V 50 60 Hz Maximum total power consumption ccccccccccccc cce 126 W Main fuse 6 3 AT for use at 100 130 V nominal 4 AT for use at 200 240 V nominal Standby POWE apsida Red Shoes Sade Bd ii dA A EA 28 W Thermal COGNE ima assis a E AAA A e ee a ee Forced air Maximum ambient temperature Ta max X 0 0 40 C 104 F Minimum ambient temperature Ta MIN ooooocoooooonroronorronoo oo 5 C 41 F Approvals BU O aida dada EN 60598 1 EN 60598 2 17 EU ENV Cs pic
5. X control and stand alone operation with scenes programmed on fixture or captured via DMX Onboard control panel and backlit LCD graphic display 8 colors 8 fixed gobos 6 rotating gobos Rotating prism Motorized focus Smooth electronic dimming Electronic strobe 630 pan and 270 tilt ranges 8 bit and 16 bit DMX control modes Data link A data link is required in order to control a X Spot via DMX The X Spot has 3 pin connectors from DMX data input and output The pin out on all connectors is pin 1 shield pin 2 cold and pin 3 hot Do not use the outputs to split the DMX link Tips for reliable data transmission Use shielded twisted pair cable designed for RS 485 devices standard microphone cable cannot transmit control data reliably over long runs 24 AWG cable is suitable for runs up to 300 meters 1000 ft Heavier gauge cable and or and amplifier is recommended for longer runs Never use both a fixture s outputs to split a DMX link To split the link into branches use a splitter Terminate the link by installing a termination plug in the output socket of the last fixture The termination plug which is a male XLR plug with a 120 Ohm 0 25 Watt resistor soldered between pins 2 and 3 soaks up the control signal so it does not reflect and cause interference If a splitter is used terminate each branch of the link Connecting the date link 1 Connect the DMX data output from the controller to the X Spot 3 pi
6. connected from power PROTECTION FROM BURNS AND FIRE PA Do not operate the fixture if the ambient temperature Ta exceeds 40 C 104 F The exterior of the fixture becomes hot during use Avoid contact by persons and materials Allow the fixture to cool for at least 10 minutes before handling JAN Keep all combustible materials e g fabric wood paper at least 100 mm 4 ins away from the head Keep flammable materials well away from the fixture Do not illuminate surfaces within 250 mm 10 ins of the fixture Do not attempt to bypass thermostatic switches or fuses Replace defective fuses with ones of the specified type and rating Do not stick filters masks or other materials onto any optical component Do not modify the fixture in any way not described in this manual Install only genuine Ludi parts PROTECTION FROM INJURY Do not look continuously at LEDs from a distance of less than 0 5 meters 20 inches from the front surface of the fixture without protective eyewear such as shade 4 5 welding goggles At less than this distance the LED emission can cause eye injury or irritation At distances of 0 5 meters 20 inches and above light output is harmless to the naked eye provided that the eye s natural aversion response is not overcome Do not look at LEDs with magnifiers telescopes binoculars or similar optical A instruments that my concentrate the light output Ensure that persons are not looking at the LEDs from wit
7. hin 0 5 meters 20 inches when the product lights up suddenly This can happen when power is applied when the product receives a DMX signal when a stand alone program suddenly increases light output intensity or when SERVICE menu items are selected Install as described in this manual a secondary attachment such as a safety cable that is approved by an official body such as TUV as a safety attachment for the weight of all the fixates it secures The safety cable must be comply with EN 60598 2 17 Section 17 6 6 and be capable of bearing a static suspended load ten times the weight of the fixture If suspending from a rigging structure attach the fixture with two evenly spaced clamps Do not use only one clamp Ensure that any supporting structure and or hardware used can hold at least 10 times the weight of all the devices they support Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture when it moves Check that all external covers and rigging hardware are securely fastened Block access below the work area and work from a stable platform whenever X Spot user s manual installing servicing or moving the fixture Do not operate the fixture with missing or damaged covers shields or any optical component Introduction Thank you for selecting the X Spot an intelligent lighting fixture from Ludi Lighting This LED based moving head spot light features Luminous high power emitters DM
8. n input male socket 2 Using the sockets that match your data cable connect the output of the fixture closest to the controller to the input of the next fixture 3 Insert a male 120 Ohm XLR termination plug in the 3 pin or 5 pin output of the last fixture on the link X Spot user s manual Setting menu Address 1 512 Auto 1 E 2 Sound ENO TiltRev A ENO Degree 360 180 270 180 E Oooo o DMX protocol DMX channel DMX value Function 1 Pan position 2 Pan position 16 bit 3 Tilt position 4 Tilt position 16 bit 5 Pan amp tilt motor speed fast gt slow 6 000 015 White 016 031 Magenta 032 047 Green 048 063 Yellow 064 079 Cyan 080 095 Red 096 111 Light green 112 127 Blue 128 191 Scroll clockwise slow gt fast 192 255 Scroll anti clockwise slow gt fast X Spot user s manual 10 11 000 007 E 13 000 015 14 000 015 X Spot user s manual 000 006 007 013 014 020 021 027 028 034 035 041 042 048 049 055 056 062 063 069 070 076 077 083 084 090 091 097 098 104 105 111 112 118 119 127 128 191 192 255 000 018 019 037 038 056 057 075 076 094 095 113 114 127 128 191 192 255 000 009 010 116 117 244 245 255 000 008 009 016 017 239 240 255 Clear Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 8 Gobo 7 Gobo 6 Gobo 5 Gobo 4 Gobo 3 Gobo 2 Gobo 1 Clear Scroll clockwise slow gt
9. os coartada EN 61000 3 2 EN 61000 3 3 EN 61000 6 2 EN 61000 6 4 X Spot user s manual LUDI LIGHTING www ludiled com Nanhai Foshan Guangdong China Phone 86 757 81280299 Fax 86 757 81858213 X Spot user s manual
10. resents risks of severe injury or death due to fire and burn hazards electric shock and falls Read this manual before installing powering or servicing the fixture follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture If you have questions about how to operate the fixture safely please contact your Ludi supplier PROTECTION FROM ELECTRIC SHOCK Disconnect the fixture from AC power before removing or installing any cover or part including fuses and when not in use Always ground earth the fixture electrically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault earth fault protection Before using the fixture check that all power distribution equipment and cables are in the perfect condition and rated for the current requirements of all connected devices Isolate the fixture from power immediately if the power plug or any seal cover cable or other component is damaged defective deformed wet or showing signs of overheating Do not reapply power until repairs have been completed Do not expose the fixture to rain or moisture Refer any service operation not described in this manual to a qualified technician X Spot user s manual Socket outlets used to supply fixtures with power or external power switches must be located near the fixtures and easily accessible so that the fixtures can be easily dis
Download Pdf Manuals
Related Search