USER MANUAL
Contents
1. blocked Do not operate this unit in environmental temperatures exceeding 35 degrees Celsius 6 Check the total maximum power of your AC wall outlet if you connect several units to one wall outlet and avoid any overloading Protection from injury and damage 1 Never use any accessories or modifications not authorized by the manufacturer of this unit 2 Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow appropriate rigging rules and your country s regulations for rigging safety See appendixes if any 3 Before plugging the AC cord in the wall outlet check whether the AC mains voltage and frequency is the same as this product is specified for Whenever your AC plug should not match the wall outlet contact you dealer immediately 4 If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check 5 Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks 6 In cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check 7 To meet all aspec2. more than 8A Do not connect any high power devices such as audio power amplifiers fog machines etc to this outlet Make sure that AN all connected devices in a chain fed by the first device do not exceed a maximum of 8A current consumption All units must be properly and separately earthed V1 00 03 2010 5 User Manual LED Flower 1x4 User Manual LED Flower 1x4 m Getting started secure mounting Hanging Rigging ceiling mounted operation Risk of injury Overhead mounting requires extensive experience AN including among others calculating working load limits good knowledge of the installation material being used and periodic safety inspection of all installation material and the unit If you lack such qualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit e The unit should be installed out of reach of people and outside areas where persons may walk by or be seated e Make sure that the installation area can hold a minimum point load of 10 times the device s weight e Infixedinstallations fix the unit with self locking screws nuts to the mounting point e When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke e Where required secure the installation with an appropria
3. 0 Static 001 149 Speed 31 180 BPM 1 BPM steps 150 175 Sound to Light 1 step per 4 Beats 176 200 Sound to Light 1 step per 2 Beats 201 255 Sound to Light 1 step per 1 Beat CH3 Strobe 000 010 Strobe off 011 255 Strobe 1Hz 23Hz V1 00 03 2010 9 User Manual LED Flower 1x4 In A mode the unit does not receive any values from the DMX input but runs through its own patterns and creates related DMX values on the output with channels 001 to 003 so that similar units can show the same chase pattern if they are connected by DMX and set to Slave It further generates a second set of control signal on channels 004 to 006 which are shifted against the signal present on channels 001 to 003 by 2 pattern steps See chapter slave operation If you leave mode A for any reason and come back later into mode A the unit will recall the last chosen pattern speed even ifthe unit was switched off in between S2L Mode Sound to Light Mode Press the MODE button 1 until the display shows S2L indicating operation in S2L Sound to Light mode In this mode a seguence of different preset pictures is played while the trigger to switch to the next picture is provided by external audio picked up by the internal microphone In S2L mode the UP DOWN buttons 2 3 are disabled In S2L mode the unit does not receive any values from the DMX input but runs through its own picture prese
4. 3 2010 7
5. 3 2010 8 User Manual LED Flower 1x4 function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover m Environmental advice This unit is build to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage at the end ofits life but shall be returned to authorized recycling stations LA m Unpacking Please check that the box contains the following items Main parts 1 pcs LED Flower 1x4 main unit 1 pcs mains cable 1 pcs operation manual If any part is missing please contact your dealer immediately for replacement m Getting started choosing a location Risk of fire The LED Flower 1x4 has been designed to work in dry indoor environments at environmental temperatures up to 35 degrees Celsius For proper operation the unit must be operated with unobstructed air convection to its outside metal case Do not Operate the LED Flower 1x4 in environments with more than 35 degrees environmental temperature or more than 75 relative humidity Operate the LED Flower 1x4 in any closed environment smaller than 10cbm unless forced air convection is provided m Getting started making AC supply connections Risk of fire Safety risk The LED Flower 1x4 has an AC outlet that is designed to carry loads of no
6. USER MANUAL LED Flower 1x4 DMX controlled RGBW 1 Cluster LED Effect ENGLISH Page 2 12 RevA 03 2010 Order code 12 015 0063 80100 1 01 User Manual LED Flower 1x4 m Introduction Dear customer congratulations on the purchase of this quality item and the trust having been put in us with this decision To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before you start using the unit m Security advice before use Warning Read this section carefully before installing powering AN operating cleaning or servicing this product The following symbols are used to identify important safety information in this manual A A DANGER WARNING WARNING WARNING Safety hazard Risk Hazardous voltage Fire hazard Read manual before of injury or death Risk of severe or installation and fatal electric shock operation General advice AN 1 Read this manual completely before using the product 2 Keep this manual in your records for future reference 3 Follow all instruction printed in this manual otherwise warranty may be void 4 Follow all printed security advice on the product itself The lighting flash with arrowhead within an equilateral triangle makes you aware of non insulated AC mains voltage inside the unit The exclamation mark within an equilateral triangle makes you aware of important operating and maintenance instructi
7. d data on the DMX output Purpose of this mode is to allow simple basic remote settings for the user who is not familiar in depth with DMX but still would like to remotely enable or disable the unit and change the most vital operation parameters The functional assignment to the receiving channel is as below CH1 DMX values 000 014 Off 015 059 Various patterns 9 patterns low speed 060 104 Various patterns 9 patterns medium speed 105 149 Various patterns 9 patterns fast speed 150 199 10 pattern loop Strobe various speeds 200 249 Single pattern loop 10 patterns sound to light 250 255 10 pattern loop sound to light d3 Mode DMX Full Mode Press the MODE button 1 until the display shows d3 indicating operation in d3 DMX Full mode In alternation with displaying d3 the display will show the DMX start address which the user can change using the UP DOWN buttons 2 3 In this mode the unit receives a DMX control signal on a packet of three consecutive DMX channels starting from the start address as set above and mirrors the received data on the DMX output Purpose of this mode is to allow more in depth control for the discerning user who looks for specific effects The functional assignment to the receiving channels is as below CH1 Play 000 All off 001 148 Static Pictures 149 150 All on 151 249 Chase Patterns 250 255 All pattern loop after 4 cycles CH2 Speed 00
8. interference the last unit of a DMX chain should be terminated Use a standard 120 Ohms XLR termination plug for DMX lines on the last device in a DMX bus chain Switch on condition The unit always returns to the last mode before it was switched off In DMX Slave SLA or DMX Mode d1 d3 all DMX values are cleared if power is switched off DMX signal drop condition The device will retain the status that it was in before the DMX signal got lost but potential tact settings will be automatically cleared V1 00 03 2010 10 User Manual LED Flower 1x4 A A V1 00 03 2010 Warning Class 1M LED product 1 2 3 Do not look into the beam from a distance of less than 40 cm 16 inches Do not stare into the beam for extended periods at a short distance Do not view the beam directly with optical instruments such as magnifiers Protection from electric shock 1 2 Do not connect the AC power plug to the unit before assembly has been completed Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault protection and overload protection Where the mains plug or an appliance coupler is used as a dis connect device the disconnect device shall remain readily operable To pull the AC Cord out of the wall outlet or the units AC socket never pull the cable itself but only the AC plug Disconnect the unit from AC supply by pulling the AC plug out
9. mplies with the following standards OEE E AE E A nd EN60598 1 2008 EN60598 2 1 1989 EU EMC eeessssssisssrrsersssssrsrrnn EN55015 2006 A1 2007 EN61547 1995 A1 2000 EU Harmonics ccccccccccccceceaceeseeseececeececeeceaueauesseeceeeeeeeeseeaueaneeeeees EN61000 3 2 2006 EU Fleka einir airnn ra a A EER ap O et EN61000 3 3 2008 US Safety id item aan dal taa aaa taa nen aa a hosted a i E UL60065 asi mamma mm merd e made vu FCC Part 15 This product meets both the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC V1 00 03 2010 11 User Manual LED Flower 1x4 m Slave Operation The LED Flower 1x4 has a sophisticated ability to not only generate a DMX signal eguivalent to its own behaviour at its DMX output on channels 001 003 but also a DMX signal representing the same pattern that currently plays but shifted by 2 pattern steps on channels 004 006 A connected slave unit can be either set to synchronous slave mode setting S in menu SLAVE then using the channels 001 003 or asynchronous slave mode setting A in menu SLAVE then using the channels 004 006 For master slave operation also see the below example A Master Slave 1 Slave 2 Slave 3 Mode A Auto or S2L Mode SLA Mode SLA Mode SLA Setting A async Setting S sync Setting A async Play Play Play master 2 steps same as master master 2 steps he Termination To avoid
10. of the wall outlet or the units AC socket before any kind of cleaning on the product Use smooth and dry cloth only for cleaning Check all connection cables before reconnecting the unit Do not expose this unit to any dripping or splashing liquids and do not place objects filled with liquids such as vases on the unit Do not operate this unit near to open water or in high humidity Choose the position of the AC cord according to the lowest risk of damage by foot steps or by squeezing it Take especially care of the AC cord outlet on the unit as well as the AC plug and wall outlet at the other end of the cable Do not open the unit for service purpose as there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons Protection from fire 1 2 3 Take care of not placing the unit near sources of heat e g powerful amplifiers fog machines Allow at least about 6 15cm between this unit and other devices or a wall to allow for proper cooling Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Do not stick filters masks or other materials directly on the LEDs or the LED cover screen Take always care of sufficient air convection in the unit s environment to avoid overheating especially when mounting in a closed environment Make sure air convection slots are not User Manual LED Flower 1x4
11. ons in the literature attached to this product 5 Take care of enough distance between this product and sources of hum and noise like electric motors and transformers 6 Carry this product with greatest care Punches big forces and heavy vibration may damage this product mechanically 7 The manufacturer takes no responsibility for injury or damage caused by not following the safety precautions and instructions printed in this manual V1 00 03 2010 2 User Manual LED Flower 1x4 m Maintenance This unit does not need regular maintenance The internal circuit is protected by a 250V 2A slow blow fuse 5x20mm fuse If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer The fuse shall only be replaced by a fuse of same specification and the replacement has to be made by qualified personnel obeying applicable safety rules m Technical data LED Flower 1x4 LEDS tianshi oore k hk 180 pcs 5mm LEDs 40 R 40 G 40 B 60 W Mains IMpUtsscvii ne aa a a a a ame we AC90 250V 50 60Hz Power supply type mmerereesesnneneneaene EARE Ern switch mode Power Consum ptio saas cant ausat aidad Ad tala katat alata max 20W DMX cohnectiOMS diania nseni apaina Ea 3 pin XLR Male Female Controly protocol AASEN DMX 512 1990 Dimensions without bracket mmee LxWxH 165x150x140mm Wei era a a a E Aa a O aa Ea ea 1 45kg m Standards This product co
12. te safety cable Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails e Never stand directly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing User interface overview e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The 1 MODE selection button installations should be inspected every year by a skilled person to be sure that 2 UP Button safety is still granted 3 DOWN Button e Make sure to comply with cooling requirements of the used power supply if any f eni A silk the Mode DMX address etc inpu 6 DMX output 7 AC output 8 AC input Upon the user s choice the unit can work stand alone or may be controlled by external DMX controllers Available modes A Mode Auto DMX Master Press the MODE button 1 until the first digit on the display show A indicating operation in A mode In this mode a varied preset pattern is replayed for which the replay speed can be set in ten steps by means of the UP 2 and DOWN 3 buttons m General Operation V1 00 03 2010 6 V1 00 0
13. ts and creates related DMX values on the output with channels 001 to 003 so that similar units can show the same picture if they are connected by DMX and set to Slave It further generates a second set of control signal on channels 004 to 006 which are shifted against the signal present on channels 001 to 003 by 2 steps See chapter slave operation SLA Slave Mode Press the MODE button 1 until the display shows SLA indicating operation in SLA Slave mode In alternation with displaying SLA the display will show either the letter S for synchronous or A for asynchronous while the user can change between these two setting using the UP DOWN buttons 2 3 When being in SLA mode with setting S synchronous the unit will receive a control signal on DMX channel 001 003 3 channels while when being in SLA mode with setting A asynchronous the unit will receive a control signal on DMX channel 004 006 3 channels Bearing in mind that any unit being in A or S2L mode acts as a master and does not only generate its own played pattern as a DMX signal on channels 001 003 but also the same pattern with 2 steps shifted see slave operation on channels 004 006 then switching between setting S and A in slave mode allow the slave unit to either play in synchronisation S of shifted against the master A V1 00 0
14. ts of functionality and security during mainte nance work to be preformed on this unit all parts should be replaced by genuine spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer m Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC reguirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE reguirements eventually not to be met any more The manufacturer takes no responsibility in this case m Functional advice This unit is immune to the presence of electromagnetic disturbances both conducted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of V1 00 03 2010 4 User Manual LED Flower 1x4 d1 Mode DMX Easy Mode Press the MODE button 1 until the display shows d1 indicating operation in d1 DMX Easy mode In alternation with displaying d1 the display will show the DMX start address which the user can change using the UP DOWN buttons 2 3 In this mode the unit receives a DMX control signal on only one channel which is chosen as the start address and mirrors the receive
Download Pdf Manuals
Related Search