Home
Instruction Manual - Mads Electronics
Contents
1. King or the seller correct WRONG COMMUNIC The communication between Check the connection cable or the Smarty and the ECM unitis battery charge level disturbed WRONG VIN The serial number of your Wait 30 seconds with the ignition key vehicle is not valid on and try again Page 15 of 16 GEEET v PERFORMANCE KING 11 Warranty How Do You Get Service If something goes wrong with your Product during the warranty period use the following procedure to return the Product to Smarty Performance King Company 1 Restore the STOCK software to your vehicle ECM DO NOT RETURN A VIN LOCKED SMARTY 2 Download and fill out the Assistance Request Module available from Smarty Performance King internet site or send an e mail to Smarty Performance King e mail information is available from Smarty Performance King internet site Include the following e Information from your sales receipt electronic copy would be appreciated The sales receipt must be from the location where you purchased your Product and must include the name of the business where you purchased the Product and the address of the business e Serial number of the product e A brief written description of the problem e Your address and other personal information to contact you 3 Contact Smarty Performance King distributors for immediate assistance 12 Declaration of Conformity For customers in North America FC Model number Smarty S 06 SSR Trade Name Smarty
2. Performance King Responsible Party Smarty Performance King SA Address Switzerland CH e mail admin madselectronics com Tested to Comply With FCC Standards FOR HOME OR OFFICE USE The device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation For customers in Europe Ce CE Mark indicates that this product complies with the European requirements for safety health environment and customer protection Page 16 of 16
3. Stock New lim To set the RPM limiter to Stock select a value below 3500 or simply 0 Shift limiter The Shift limiter can be programmed Stock or Off Shift lim Stock 0 stock 1 off Shift limiter programmed Off allows the engine to produce full power also during gear shifts or power braking DO NOT USE IT WITH A STOCK TRANSMISSION Torque The Torque selection can be programmed 0 stock 1 mild 2 moderate or 3 wild Torque stock 1 New T IMPORTANT with torque level 2 or above an aftermarket clutch AT Transmission is recommended Low load Injection Timing The Timing selection for low load driving condition can be programmed Stock or with a value between and 50 To select the stock timing press 0 Timing LL Stock 1 New T High load Injection Timing The Timing selection for hig load driving condition can be programmed Stock or with a value between and 50 To select the stock timing press 0 Timing HL Stock New T Low load Rail Pressure The Rail Pressure selection for low load driving condition can be programmed Stock or with a value between and 50 To select the stock rail pressure press 0 Rail Pr LL stock New R P High load Rail Pressure The Rail Pressure selection for high load driving condition can be programmed Stock or with a value between and 50 To select the stock rail pressure press 0 Rail Pr HL stock New R P Low load Injection
4. CU nee rs wf PERFORMANCE KING SMARTY SSR Micro Tuner model SO6 SSR Super Sport Race Common Rail Dodge Ram 5 9L 24 Valve Cummins Diesel Engine Instruction Manual PLEASE READ THIS ENTIRE INSTRUCTION MANUAL BEFORE PROCEEDING www madselectronics com Rev 4 05A Page 1 of 16 CNG mary v PERFORMANCE KING THIS IS A HIGH PERFORMANCE PRODUCT USE AT YOUR OWN RISK This product is intended for OFF ROAD USE ONLY This product is not intended to be used to break the law Do not use this product until you have read the following agreement This agreement sets forth the terms and conditions for the use of this product The installation of this product indicates that the buyer has read and understands this agreement and accepts the terms and conditions DISCLAIMER OF LIABILITY Smarty Performance King its distributors jobbers and dealers hereafter Seller shall be in no way responsible for the product s proper uses and service THE BUYER HEREBY WAIVES ALL LIABILITY CLAIMS The buyer acknowledges that he is not relying on the Sellers skill or judgement to select of furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof and the buyer hereby waivers all remedies or liabilities expressed or implied arising by law or otherwise including without any obligation of the seller with respect fitness merchantability and consequential damages wh
5. Duration The injection duration for low load driving condition can be programmed Stock or with a value between and 50 To select the stock injection duration press 0 Page 7 of 16 GEEET wf PERFORMANCE KING DurationLL Stock New D High load Injection Duration The injection duration for high load driving condition can be programmed Stock or with a value between and 50 To select the stock injection duration press 0 DurationHL Stock New D Pre Injection The Shift limiter can be programmed Stock or Off Pre Inj Stock 0 stock 1 off Pre Injection programmed Off disables the preliminary injection of the engine The adjusted parameters are stored in Smarty memory and used on next ECM programming Smarty asks the confirmation to program the ECM Program CaTCHER Press gt Smarty will read the serial number of your vehicle and the serial number of your ECM then store them into its onboard memory for future reference From this moment on Smarty will work only with your vehicle until your vehicle is restored back to the stock settings by Smarty Press the gt key to begin the updating session If the connection cannot be established Smarty asks you to switch off the ignition key Turn key OFF Press gt Turn the ignition key to OFF Press the gt key Smarty will then ask you to switch the ignition key ON in order to retry the connection T
6. EEET wf PERFORMANCE KING e USB Connector Used for connecting Smarty to a personal computer for updates The update softwares can be downloaded from Smarty Performance King internet site www madselectronics com A USB cable is not included Standard USB 1 1 or USB 2 0 cables can be used to connect Smarty to your personal computer e 15 pin Connector Used to connect Smarty to the vehicle through the vehicle s diagnostic port with an OBD II cable The OBD II J1926 diagnostic connector cable is included in Smarty s box Note Connecting any other cable to the 15 pin connector invalidates Smarty Performance King warranty because it could damage Smarty Smarty automatically switches on when one of the two connections described above is made NEVER CONNECT BOTH CABLES AT THE SAME TIME This could damage Smarty and the computer USB port Such failure is not covered by the Smarty Performance King warranty 3 Connecting Smarty to your vehicle e Turn on the ignition key to the RUN position DO NOT START THE ENGINE e Plug the furnished OBD II cable into the 15 pin connector in the top edge of Smarty and GENTLY tighten the screws by hand Over tightening these two screws DOES NOT make a tighter or better connection The screws are provided to keep the plug held gently to Smarty e Plug the Smarty cable into the diagnostic port on your vehicle The diagnostic port is located inside the cab to the passenger side of the steering wheel at the
7. IE EE NR N EE 7 Low load Injection Duration ccsccsssccssssccsssccsssscssscscssscssssscsssssessscsossscsssassssscsessscsssssssssssesssssonsssess 7 Hish load Injection Durations iccscsccssconscescnssdsvcsssdecesessvcsassonavsesenssesetsessecesestecsvessstcssensdesesesedecesesssesses 7 Pr Injectiot sesiciesedsssscdidecacetoacevocssdsceseandesoasssdedeccdnassoestessansedudesoescesennccsoacesendsesasbesedsssasaceessccsescasadcecaseseossaee 8 Changing SOW DT REPRE 9 Recovery OF the ECM csissisccasssssesscssssesoncssessssecdsosasssssbesdscssnsseasssecdsstoncsestessosses esesedsssssaded onnsesescdoecssesedess 10 5 Power on Demand sesse esse LL GO Reading Key on COUNCCT vis seders gered LL TARCAGING DE LEER EE EE N EN ED N EE N N N ka Reading Diagnostic Trouble Codee ccsssccsssscsssscssssscssssscssscsssssssssssesssssssssssssssessscsssssscsssssssscsossees 12 Clearing DT Gel EA N EE EE EE EE N 13 SABS Update tire height update csccsssccssssccssssccsssscsssssccssssscsssscsssssssssssssssssssssssssssssssssssssssee LD DU Patri g SIVA CY er Rm LA 10 Appendix A Error messages Gescription csssccssssccssssccssssccsssscsssssssssscsssssssssssssssssssssesseees LO 11 Warrant nui ii eire Petr di ede de bv S De Ge UAR De OG GR DARE bed RAINER EE N AE boo EUER oe ke ia dela Fa sao oes dran LO 12 Declaration of ConfOrm
8. ate the functional parameters of the ECM The following screen will appear Updating ECM Please wail During the updating session Smarty can ask to Turn key OFF and Turn Key ON Please follow these instruction DO NOT DISCONNECT Smarty before the updating session is completed At the end of the recovery operation the following screen appears UPDATE DONE After a few seconds Smarty displays the following message Unplug Smarty Please unplug Smarty from the diagnostic port and turn the ignition key off for 15 seconds The job is done The ECM has been returned to the STOCK software and Smarty is no longer VIN Locked You re ready to start from the beginning again 5 Power on Demand This function allows the user to select the preferred power level instantly also during the driving At the PoD menu 1 Power OnDemand 2 Main menu press 1 key to enter the Power on Demand function the Power page will appear Power can be selected between 99 full power and 0 lower power Just type the preferred power The number will appear in the second line of the display after a while it appears on the first line this confirms that the value has been correctly sent to the truck You have just to release the throttle to apply the new power Smarty waits for a new Power on Demand adjustment To return to the PoD menu press lt Page 11 of 16 fu 45 v PERFORMANCE KING 6 Reading Key on counter Smarty leaves n
9. atever or not occasioned by the sellers negligence The Seller disclaims any warranty and expressly disclaims any liability for personal injury and damages The buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of the equipment purchased Under no circumstances will the seller be liable for any damages or expenses by reason of use or sale of any such equipment The Seller assumes no liability regarding the improper installation or misapplication of its products It is the installer s responsibility to check for proper installation and in doubt contact the manufacturer The buyer is solely responsible for all warranty issues from the manufacturer LIMITATION OF WARRANTY Smarty Performance King Hereafter Seller gives Limited Warranty as to description quality merchantability and fitness for any particular purpose productiveness or any other matter of the Seller s product sold herewith The Seller shall be in no way responsible for the products proper use and service and the buyer hereby waives all rights other than those expressly written herein This warranty shall not be extended altered or varied except to be a written instrument signed by Seller and Buyer The warranty is limited to one 1 year from the date of sale and limited solely to the parts con
10. bottom of the dash panel near the floor 4 Updating the ECM First time update Turn on the ignition key to the RUN position DO NOT START THE ENGINE Plug Smarty s cable into the diagnostic connector of your vehicle Smarty will display Smarty CR V 4 00A D 1 00A The second line of the display shows the firmware version and the tuning data version Both the internal firmware and the tuning data information can be updated connecting a personal computer See Smarty Performance King internet site for more details Then the main menu appears 1 ECM Update 2 Data Read From the main menu press 1 to select ECM Update Before the programming The optional parameters have to be adjusted The list of optional parameter varies according to the installed software For each parameter the current option status is shown on the first line of the display With Smarty numeric keyboard the optional parameters can be adjusted To maintain unchanged the current parameter press the gt key You can return back one step in any moment with the lt key Speed limiter The speed limiter can be adjusted anywhere from 25 to 250 MPH in one MPH steps IMPORTANT Your tires might not be rated for increased speeds Please check your tires rating Page 6 of 16 GEEET wf PERFORMANCE KING To set the speed limiter to Stock select 0 RPM limiter The RPM limiter can be programmed with values between 3600 and 6000 RPM limit
11. ds the usual main menu will appear ECM ABS Update Data Read Press the 1 key and Smarty displays the following screen 1 ECM Update 2 ARS Update Press the 1 key to select ECM Update Smarty will try to establish the communication with the ECM The connection cannot be established because the last updating session has been interrupted Smarty knows that the last update has not been performed correctly and will recognise the not operational ECM condition Smarty asks you to switch off the ignition key Turn key OFF Press gt Turn the ignition key to OFF Press the gt key Smarty will then ask you then to turn ON the ignition key in order to retry the communication Turn key ON Press gt Page 10 of 16 GEEET wf PERFORMANCE KING Turn the ignition key to the RUN position DO NOT START THE ENGINE Press the gt key The communication cannot start yet Smarty shows the following message A previous update has been interrupted Press gt to restore ECM to Stock The message is longer than the display so the message will repeatedly scroll across the screen Press the gt key The recovery operation starts You will see the following message Please wait After a few seconds a numeric counter with the percentage of the transmitted software will appear At the end of the transmission when 100 is reached Smarty will upd
12. entage of the transmitted software At the end of transmission when 100 is reached Smarty will update the functional parameters of the ECM The following screen will appear Updating ECM Please wait During the updating session Smarty can ask to Turn key OFF and Turn Key ON Please follow these instructions DO NOT DISCONNECT Smarty before the updating session is completed At the end of the updating session the following screen will appear UPDATE DONE After a few seconds Smarty displays the following message Unplug Smarty Please unplug Smarty from the diagnostic port and turn the key of for 15 seconds Recovery of the ECM If an interruption occurs during an Update or the Update operation is terminated before the normal end for any reason the ECM will not be operational You must recover the ECM using Smarty to resume the update process Attention The engine will not start before the ECM has been recovered properly The Wait to Start Light will flash continuously DON T PANIC Smarty Performance King has developed a special boot loader software that is used during all the ECM Updates Unlike the OEM DRBIII tool there is no need to pull fuses or disconnect the batteries No tools are needed At Smarty Performance King we ve done our homework Just follow the directions on Smarty s display Smarty will handle the situation for you in a few simple steps Unplug Smarty then plug it in again After a few secon
13. ity eeeo enero eos vo orna ee ese soosscoesedesevevesessbssevensdenessveesssesevevesesseonssssevessteeL O Page 4 of 16 GEEET wf PERFORMANCE KING 1 Before You Begin Your vehicles STOCK program Your vehicle s ECM must contain the manufacturer s STOCK factory program If you have used a programmer from another aftermarket company you must use their product to return your ECM back to STOCK condition before proceeding If you have a performance enhancing device installed it must be removed Service Centers If you need to return your vehicle to a service center restore the vehicle ECM to its STOCK program The service center might reprogram your vehicle with an updated STOCK software ECM reflash without your knowledge If your vehicle has not been returned to its STOCK program prior to a service visit and the ECM is reflashed the Smarty Micro Tuner will no longer be able to program your vehicle Such failure is not covered by the Smarty Performance King warranty Under no circumstances will we refund repair or warranty units that are sent in that are locked Locking and Unlocking Smarty Once Smarty is used on a vehicle it is VIN LOCKED to that vehicle AND to that ECM Smarty can be used only on that vehicle to update ECM software and ABS speedometer changes In order to unlock Smarty you must use Smarty to return the ECM to the STOCK software otherwise Smarty will remain locked Only Smarty can unlock itself Follow the i
14. meter of the vehicle can be adjusted according to the tire height From the main menu shown below press the 1 key 1 ECM ABS Update 2 Data Read To change the tire height choose the ABS update function Press the 2 key in the second menu as shown below 1 ECM Update 2 ABS Update Smarty will try to establish the communication with the ABS If the ignition key was not turned to the RUN position Smarty will display this message Turn key OFF Press Press the gt key then Smarty will prompt you to turn on the ignition key to retry the connection Turn key ON Press gt When the connection has been established Smarty shows the current tire height Curr Tire in the top line of the screen Page 13 of 16 GEEET v PERFORMANCE KING Curr Tire 40 00 New Tire Type in the correct tire height with the numerical keys entering a decimal point is not required Any tire height from 25 00 to 45 00 can be chosen in 0 05 increments If you enter an increment other than 0 05 Smarty will round it to the next correct increment The lt key can be used to change entries After you have entered the correct tire height press the gt key Smarty will prompt you for confirmation to proceed New Tire 42 25 Press gt to start The key can be used return to the previous screen to change the New Tire size Press the gt key to start upda
15. nstructions in this Manual to return your vehicle to STOCK software Once unlocked Smarty may be used on a different vehicle While Smarty is VIN Locked it can still be used to read and clear Diagnostic Trouble Codes DTCs on a vehicle and ECM that it is NOT locked to Vehicle preparation Before connecting the Smarty Micro Tuner to your vehicle make sure that all power draining accessories are turned off Radio headlights lights cell phones etc All those devices need to be turned off Please apply the parking brake before you begin a download As the Smarty Micro Tuner needs full battery voltage to program ensure your vehicle battery is fully charged and NOT connected to a battery charger Do not disturb or remove the connection cable during the updating operation Smarty preparation During the first use Smarty reads the identification parameters of your vehicle After the first use Smarty can be used only with your vehicle Returning the ECM to STOCK software restores Smarty into the original unlocked condition 2 Smarty Overview Keyboard operation Smarty s keyboard is composed of 12 keys e Numerical keys from 0 to 9 used to select menu options and enter numerical values e Right arrow key used to confirm the selected operation e Left arrow key used to go one step back in the operation flow Connectors Two connectors are available in Smarty s upper ed ooo00o00 00 0 90000000 USB ECM Cable Page 5 of 16 G
16. o footprint all the trip data stored inside the ECM remains unchanged As an example you can verify that the Key on counter remains stored From the main menu press the 2 key to select the data read function ECM ABS Update Data Read Key on counter DTC codes Smarty will try to establish a communication with the ECM If the Key was not in the on position Smarty will display this message Turn key OFF Press gt Pressing the gt key Smarty asks you to turn on the ignition key to retry the connection Turn key ON Press When the connection has been established Smarty shows the key on counter Key cnt 567 Press gt Please remember that every time the key is switched off as at the end of the programming the key on counter increases 7 Reading DTC s Reading Diagnostic Trouble Codes The DTC Diagnostic Trouble Code reader function present in Smarty Micro Tuner is for convenience purpose only Smarty Performance King makes no warranty to the accuracy of the interpretations The description of all the DTC is shown on Smarty s display Many logged codes are transitory they are automatically reset From the main menu press the 2 key to select the data read function ECM ABS Update Data Read Key on counter DIC codes Smarty will try to establish communication with the ECM If the Key was not turned into the on position Smarty will display this message u
17. rn key OFF Press gt Pressing the gt key Smarty asks you to turn on the ignition key to retry the connection urn key ON Press gt When the connection has been established if no DTC codes are present the following screen appears Page 12 of 16 CU eR wf PERFORMANCE KING No DTC stored YT os ON Press gt If one or more DTC s are stored Smarty shows the number of DTC s present with the following screen 8 DIC present With the keys lt and gt all the present DTC codes can be displayed one code at a time with the following screen DTC 1 P0108 MAP sensor volta The first line of display shows the DTC P code The second line shows the DTC code description If the DTC code description is longer that the physical dimension of the display the description will scroll across the screen Clearing DTC codes At the end of the DTC code list Smarty can either clear all the stored DTC codes from the ECM memory or exit 1 Clear DTC o bxit Press the 1 key to clear all the DTC codes stored in the ECM Press the 2 key the DTC codes will not be erased and Smarty will return to the main screen When the erasing operation has been completed the following screen appears DTC Cleared Press gt 8 ABS Update tire height update Once Smarty is VIN Locked i e a CaTCHER software has been loaded in the ECM the speedo
18. tained within the products kit All products that are in question of warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt All Warranty claims are subject to approval by Smarty Performance King Under no circumstances will the Seller be liable for any labor charged or travel time incurred by in diagnosis for defects removal or reinstallation of this product or any other contingent expenses Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment In the event that the buyer does not agree with this agreement THE BUYER MAY PROMPTLY RETURN THIS PRODUCT IN A NEW AND UNUSED CONDITION WITH A DATED PROOF OF PURCHASE TO THE PLACE OF PURCHASE WITHIN TEN 10 DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS THE TERMS AND CONDITIONS Page 2 of 16 fu 46 wf PERFORMANCE KING CAUTION This Smarty Performance King product is intended for use on unmodified stock engines Remove any performance enhancing electronic devices and make sure the ECM has been returned to STOCK if you have used another manufacturer s programmer before the Smarty Micro Tuner The use of this product to change the performance characteristics of your vehicle could invalidate the warranty provided by the vehicle manufacturer Cons
19. ting the ABS unit with the new tire height A typical ABS change will take only a couple of seconds When the operation has been successfully completed the following screen appears PROGRAM DONE The ABS unit does not always change so Smarty will re read the tire height from the ABS unit and display the results as shown in the following screen Curr Tire 42 29 Press If the ABS unit did not change to the new tire height Press the lt key to return to the previous screen and re enter the correct tire height When the tire height change is completed press the gt key Smarty will display the following screen Unplug Smarty Turn key OFF Please unplug Smarty from the diagnostic port and turn the ignition key off for 30 seconds Notes To increase the speedometer reading increase the tire size To decrease the speedometer reading decrease the tire size The ABS accuracy is questionable Verify the speedometer reading with a GPS or by pacing a vehicle with a speedometer know to be accurate 9 Updating Smarty Both the internal firmware and the tuning data information can be updated through USB connector Please see Smarty Performance King internet site www madselectronics com for more details and software download Page 14 of 16 fu 45 wf PERFORMANCE KING 10 Appendix A Error messages description This section contains all the possible error messages shown by Smarty Error message Cause Solu
20. tion CAN ERROR A problem in the CAN Bus Check connection cable or contact communication Smarty Performance King if the problem persists ABS unit doesn t work unit COMM TIME OUT The ECM of the vehicle Turn the ignition key on DO NOT doesn t answer to Smarty START ENGINE or Check the connection cable has been changed STOCK before changing ECM Empty Memory The last Update operation Repeat the Update operation Please Update through USB port has been The data files are available on the unsuccessfully completed Smarty Performance King internet site Smarty memory has been corrupted assistance Smarty s memor assistance Memory Written The update file transmitted Download again the update file from Wrong Data File to Smarty through USB port Smarty Performance King internet site is corrupted and update Smarty with the correct file has been interrupted recovery procedure vehicle has not been verified SW Version doesn t The ECM software version Please contact Smarty Performance Match S N doesn t match with the serial King or the seller number UNKNOWN SOFTWARE Your vehicle contains a Please contact Smarty Performance software version unknown to King or the seller VIN Locked Smarty has been connected Restore the original vehicle back to to a different vehicle STOCK before connecting Smarty to a new vehicle WRONG CAN BUS The connection between Please contact Smarty Performance Smarty and the ECM is not
21. ts STOCK program prior to a service visit and the ECM is reflashed the Smarty Micro Tuner will no longer be able to program your vehicle Such failure is not covered by the Smarty Performance King warranty Under no circumstances will we refund repair or warranty units that are sent in that are locked Page 3 of 16 fy a v PERFORMANCE KING Index MEd You BC ul mc PG Your Vehicle s STOCK procrai ccssssestsesssssesosessessssosssesecessensssesisseesessensssuansssesesecanssenaessontsesesessendesesecses 5 Service CONCErS eL 5 Locking and Unlocking Smarr t cccscccsssssssssessssscsssccsssssssssscsssssssssscsssssssssssssscssssssssssesssscssssscssaseseass 5 Vehicle PrePparatiOnseieccccacdiccccscscrcesecsssencebecccestdsesonsstecsessecsssectcenancevstessecteuestesseaeseasdevecesssdveveasevessessdevecensss 5 Smarty eg EE N OE e oiea Esa s a sera asisas rionak oasi siise 5 Pont d lcxs o PUMCT seges ALPE EISE IE S EE EE 5 efTe DT 5 3 Connecting Smarty to your vehicle eee eee eee eee eee ee eere ee eese eee en ese Ge Gee gee gee sees ee 4 Updatine th Ui ecc DRE First ime Ui LES c ER OS ER ER aSar 6 SPO LMC GR MEE 6 High load Injection Timinng ccccccssscssssssssssssssccsssscsssscssssssssscsssscsssesscsssscsssssssesscssessssessssssessseasscesnns 7 Low load Rail y IE ic 7 High load Rail GES
22. ult your vehicle warranty before using the product on your vehicle NEVER CONNECT BOTH THE SMARTY CONNECTORS AT THE SAME TIME This could damage Smarty and the computer USB port NEVER UNPLUG SMARTY WHILE IT IS UPDATING YOUR ECM Smarty can recover without pulling fuses or disconnecting batteries BUT do not intentionally create this situation When Smarty is DONE with ECM updates ABS changes or clearing DTC codes it may be unplugged even if Smarty does not display the typical Unplug Smarty and Turn Key OFF screen It is recommended that you do not store your Smarty Micro Tuner in your vehicle if ambient temperatures in your area fall below 32 F Excessively low temperatures can cause malfunction or damage to Smarty Micro Tuner that is not covered by the Smarty Performance King warranty In the case of ECM replacement restore the ECM back to the STOCK software before the ECM replacement Smarty works only with one vehicle and one ECM at a time while it is VIN Locked Under no circumstances we will refund repair or warranty units that are send in and result VIN locked RESTORE ECM TO STOCK SOFTWARE BEFORE ANY SERVICE ASSISTANCE If you need to return your vehicle to a service center restore the vehicle ECM to its STOCK program by following the instruction in this manual The service center might reprogram your vehicle with an updated STOCK software ECM reflash without your knowledge If your vehicle has not been returned to i
23. urn key ON Press gt Turn the ignition key to the RUN position DO NOT START THE ENGINE Press the gt key to begin the updating session You will see the following screen CHECKING DATA Please wait Smarty checks its memory content before sending the data to the truck After a few seconds a numeric counter begins with the percentage of the transmitted software At the end of the download when 100 is reached Smarty will update the functional parameters of the ECM The following screen will appear Updating ECM Please wait During the updating session Smarty can ask to Turn key OFF and Turn Key ON Please follow these instructions DO NOT DISCONNECT Smarty before the updating session is completed At the end of the updating session the following screen appears UPDATE DONE After a few seconds Smarty displays the following message Page 8 of 16 GEEET PERFORMANCE KING v Please unplug Smarty from the diagnostic port and turn the Key off for 15 seconds Remember to restore the STOCK software before returning your vehicle to a service center Changing Software Turn on the ignition key to the RUN position DO NOT START THE ENGINE Plug Smarty s cable into the diagnostic connector of your vehicle Smarty will display Smarty CR 4 V 4 00A D 1 00A When the symbols are displayed on the first line Smarty is VIN locked to a vehicle The second line of the display shows the firm
24. ware version and the tuning data version After a few seconds the PoD menu will appear 1 Power OnDemand 2 Main menu Press the 2 key to select the main menu ECM ABS Update Read DTC codes ECM Update 2 ABs Update Press the 1 key to select ECM Update Smarty asks you to select either CaTCHER Software Versions see Change CaTCHER Programs below or the STOCK software 1 CaTCHER SW e stock Sy Return to STOCK program Press the 2 key Smarty asks for confirmation to restore the ECM to STOCK software Program STOCK SW Press gt Press the gt key The ECM is restored to STOCK software and Smarty is unlocked Smarty can now be used on another vehicle Change CaTCHER parameters Press the 1 key in the above described menu Before the programming The optional parameters have to be adjusted The list of optional parameter varies according to the installed software Please see the previous chapter for the parameter description A the end of the parameters adjustment Smarty asks the confirmation to program the ECM Program CaTCHER Press gt Press the gt key to confirm your selection and to begin the updating session You will see the following screen CHECKING DATA Please wait Smarty checks its memory content before sending the data to the truck Page 9 of 16 fu aaa wf PERFORMANCE KING After a few seconds a numeric counter begins with the perc
Download Pdf Manuals
Related Search
Related Contents
Brady 2461 Printer User Manual 心の機能改善 NLPベーシックコース - NPO法人いきいき・のびのび健康 E Instruments BTU4400 Industrial Combustion Analyzer User Manual 取扱説明書 充電式 インパクトドライバ TD135D GE USM Go Operating Manual Copyright © All rights reserved.
Failed to retrieve file