8-Port 10/100Mbps 802.3af / 802.3at PoE + 1
Contents
1. Light indicates the link through that port is successfully established Blink Indicates that the switch is actively sending or receiving data over that port LNK ACT Green 2 2 Rear Panel The rear panel of the PoE Ethernet Switch indicates an AC inlet power socket which accepts input power from 100 to 240V AC 50 60Hz 2A FGSD 910P or 100 to 240V AC 50 60Hz 2 5A FGSD 910HP Figure 2 3 FGSD 910P Switch Rear Panel Figure 2 4 FGSD 910HP Switch Rear Panel The device is a power required device meaning it will not work till it is powered If your networks should be active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime Power In some area installing a surge suppression device may also help Notice to protect your FGSD 910P FGSD 910HP from being damaged by unregulated surge or current to the FGSD 910P FGSD 910HP or the power adapter Before startup Before your installation begins please refer to the following for your cabling 10 100Base TX Port 1 to Port 8 All 10 100Base TX ports come with Auto Negotiation capability They automatically support 100Base TX and 10Base T networks Users only need to plug a working network device into one of the 10 100Base TX ports and then turn on the PoE Ethernet Switch The port will automatically run in 10Mbps 20Mbps 100Mbps or 200Mbps after2. 910P FGSD 910HP PoE Ethernet Switch consists of 8x Auto Sensing 10 100Mbps Ethernet RJ 45 Ports and 1x Auto Sensing 10 100 1000Mbps Ethernet RJ 45 Port The LED Indicators are also located on the front panel of the PoE Ethernet Switch OH T Sport 10 100Mbps 1 Gigabit 802 3af PoE Switch 1 FGSD 910P Figure 2 1 FGSD 910P Switch Front Panel 8 Port 10 100Mbps 1 Gigabit 802 3at PoE Switch 1 2 3 a 5 6 E w 100 Jj LNK AC d Ve H FGSD 910HP mee Wi Figure 2 2 FGSD 910HP Switch Front Panel 2 1 1 LED Indicators E System LED Color Function PWR Green Light Indicates the switch has power E Per 10 100Mbps Port LED Color Function Light Indicates the link through that port is successfully established at 10 100Mbps full duplex mode Blink Slowly Indicates the link through that port is LNK ACT Green successfully established at 10 100Mbps half duplex mode Blink Fast Indicates that the switch is actively sending or receiving data over that port Light Indicates the port is providing 48V FGSD 910P 56V FGSD 910HP DC in line power PoE Orange E Per 10 100 1000Mbps Port LED Color Function Light Indicates the link through that port is successfully established at 1000Mbps Blink Slowly Indicates the link through that port is successfully established at 100Mbps Off Indicate the link through that port is successfully established at 10Mbps Speed Green
3. A 2 Switch s Data RJ 45 Pin Assignments 1000Mbps 1000Base T PIN NO MDI MDI X 1 BI_DA BI_DB 2 BI_DA BI_DB 3 BI_DB BI_DA 4 BI_DC BI_DD 5 BI_DC BI_DD 6 BI_DB BI_DA 7 BI DD BI_DC 8 BI_DD BI_DC Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard 4 22 A3 10 100Mbps 10 100Base TX When connecting your PoE Ethernet Switch to another Fast Ethernet switch a bridge or a hub and a straight or crossover cable are necessary Each port of the Switch supports auto MDI MDI X detection That means you can directly connect the Switch to any Ethernet devices without making a crossover cable The following table and diagram show the standard RJ 45 receptacle connector and their pin assignments RJ 45 Connector Pin Assignment PIN NO MDI MDI X Media Dependant Interface Media Dependant Interface Cross 1 Tx transmit Rx receive 2 Tx transmit Rx receive 3 Rx receive Tx transmit 4 5 Not used 6 Rx receive Tx transmit 7 8 Not used The standard cable RJ 45 pin assignment KED The standard RJ 45 receptacle connector 23 1 There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable con
4. negotiating with the connected device 10 100 1000Base T Port 9 The 10 100 1000Base T port comes with Auto Negotiation capability which automatically supports 1000Base T 100Base TX and 10Base T networks Users only need to plug a working network device into the 10 100 1000Base T port and then turn on the PoE Ethernet Switch The port will automatically run in 10Mbps 20Mbps 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after negotiating with the connected device Cabling Each 10 100Base TX and 10 100 1000Base T port uses RJ 45 sockets similar to phone jacks for connection of unshielded twisted pair cable UTP The IEEE 802 3 802 3u 802 3ab Fast Gigabit Ethernet standard requires Category 5 UTP for 100Mbps 100Base TX 10Base T networks can use Cat 3 4 5 or 1000Base T uses 5 5e 6 UTP see table below Maximum distance is 100 meters 328 feet Port Type Cable Type Connector 10Base T Cat 3 4 5 2 pair RJ 45 100Base TX Cat 5 UTP 2 pair RJ 45 1000Base T Cat 5 5e 6 UTP 4 pair RJ 45 Any Ethernet devices like hubs PCs can connect to the FGSD 910P FGSD 910HP PoE Ethernet Switch by using straight through wires The nine RJ 45 ports are auto MDI MDI X which can be used on straight through or crossover cable 2 3 Desktop Installation To install the PoE Ethernet Switch on desktop simply follow the following steps Step 1 Attach the rubber feet to the recessed areas on the bottom of the PoE Eth
5. of its PoE port can link to a specific 802 3af PoE IP camera for the administrators to centrally and efficiently manage the surveillance system in one site The 1 Gigabit TP interface in the PoE Ethernet Switch also provides Gigabit TP connection for uplink to public server groups Perfect Combination 8 Port PoE Switch 8 Ch NVR 8 PoE IP Cameras wg 6 dB a zm 1 1 Q 100Base TX UTP with PoE 10008ase T UTP 8 Channel NVR Monitoring Center Figure 2 8 802 3af IP Surveillance with NVR Connection Cable distance for switch The cable distance between the PoE Ethernet Switch and other network equipment should not exceed 100 meters for UTP STP cable Make sure the wiring is correct It can use Category 3 4 5 cable in 10Mbps operation To reliably operate your network at 100Mbps or 1000Mbps you must use an Unshielded Twisted Pair UTP Category 5 5e 6 cable or better Data Grade cabling While a Category 3 or 4 cable may initially seem to work it will soon cause data loss 2 5 2 IP Office Department Workgroup PoE Switch With the business office expansion the additional telephones required could be installed in less cost via the implementation of PoE IP Telephony system than that of the traditional circuit wiring telephony system The PoE Ethernet Switch helps enterprises to create an integrated data voice and powered network The IEEE 802 3af compliant
6. of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN55022 2010 AC 2011 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN55024 2010 IEC 61000 4 2 2008 IEC 61000 4 3 2010 IEC 61000 4 4 2012 IEC 61000 4 5 2005 IEC 61000 4 6 2008 IEC 61000 4 8 2009 IEC 61000 4 11 2004 EN60950 1 2006 A11 2009 A1 2010 A12 2011 Responsible for marking this declaration if the Manufacturer D Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager Taiwan 10 Feb 2014 idi Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 This page is intentionally left blank This page is intentionally left blank
7. 0 100Base TX ege e estera o rover NSA peor eo versae v Fore ener dos nas 23 1 Introduction 1 1 Checklist Check the contents of your package for the following parts FGSD 910P FGSD 910HP x 1 User s Manual x 1 Power Cord x 1 Two 19 Rack mounting Brackets with Attachment Screws x 8 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them again to repack the product in case there is a need to return it to us for repair The term PoE Ethernet Switch mentioned in this user s manual also means the FGSD 910P FGSD 910HP 1 2 Product Description Centralized Power Distribution for Ethernet Networking The FGSD 910P FGSD 910HP a new member in the PLANET 802 3af 802 3at PoE Fast Ethernet Switch family is an 8 port 10 100Mbps 802 3af 802 3at Power over Ethernet 1 Gigabit Port Switch with a total of 130 watts of PoE budget which is an ideal solution to fulfilling the demand of sufficient PoE power for network applications with Fast Ethernet speed transmission The eight 802 3af 802 3at PoE ports provide PoE power injector function which is able to drive 8 IEEE 802 3af compliant powered devices or 4 IEEE 802 3at compliant powered devices FGSD 910HP only The FGSD 910P FGSD 910HP also provide a simple cost effective and non blocking wire speed performance It comes with a 12 inch metal compact
8. 8 Port 10 100Mbps 802 3af 802 3at PoE 1 Port 10 100 1000Mbps Desktop Switch FGSD 910P FGSD 910HP User s Manual Trademarks Copyright PLANET Technology Corp 2014 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found
9. EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN55024 2010 IEC 61000 4 2 2008 IEC 61000 4 3 2010 IEC 61000 4 4 2012 IEC 61000 4 5 2005 IEC 61000 4 6 2008 TEC 61000 4 8 2009 IEC 61000 4 11 2004 EN60950 1 2006 A11 2009 A1 2010 A12 2011 Responsible for marking this declaration if the Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager Taiwan 18 June 2013 Jal Jan e Place Date egal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw _http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 Q PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product 8 Port 10 100Mbps 802 3at PoE 1 Port 1000Mbps Desktop Switch Model Number FGSD 910HP Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation
10. I MDI X Flow control for Full Duplex operation and back pressure for Half Duplex oper LED indicators for system power per port PoE ready and PoE activity speed Model Hardware Specification FGSD 910P FGSD 910HP Network Connector 8 Port RJ 45 for 10 100Base TX Port 1 to Port 8 1 Port RJ 45 for 10 100 1000Base T Port 9 PoE Inject Port 8 Port with 802 3af PoE 8 Port with 802 3at PoE injector function injector function LED Display System Power Green Per PoE port PoE Orange LNK ACT Green Gigabit port Speed Green LNK ACT Green Switch Architecture Store and Forward switch architecture MAC Address Table 4K MAC address table with Auto learning function Switch Fabric 3 6Gbps Switch Throughput 2 67Mpps 64Bytes Flow Control Back pressure for Half Duplex IEEE 802 3x Pause Frame for Full Duplex Power Requirements AC 100 240V 50 60Hz 2A max Power Consumption 150 watts 511BTU Dimensions W x D x H 280 x 180 x 43mm W x D x H 1U height Weight 1 7kg Power over Ethernet PoE Standard IEEE 802 3af Power over Ethernet PSE IEEE 802 3at Power over Ethernet PSE PoE Power Supply Type End Span End Span PoE Power Output Per Port 48V DC 350mA Max 15 4 watts Per Port 56V DC 600mA Max 30 watts Power Pin Assignment 1 2 3 6 1 2 3 6 PoE Power Budg
11. IP Phones can be installed without the need of an additional power cable because the power can be provided via the standard Ethernet cable from the connected PoE Ethernet Switch The Wireless AP group PoE IP Phones and Analog Telephony Adapter work perfectly with the PoE Ethernet Switch which injects power through the Ethernet cables With the PoE Ethernet Switch IP Telephony deployment becomes more reliable and cost effective which helps enterprises save tremendous cost when upgrading from the traditional telephony system to IP Telephony communications infrastructure PoE VoIP Phone lea Sie ayes Se is lene ee Phone PoE VoIP ATA 100Base TX UTP _ 100Base TX UTP with PoE t H 1000Base T UTP 1 1 H zeen Q PoE IP Camera 802 3at Splitter 0 Power Line DC Telephone wire Figure 2 9 IP Office Department Workgroup PoE Switch Connection 2 6 Power over Ethernet Powered Device 3 5 watts Voice over IP phones Enterprise can install POE VoIP Phone ATA and other Ethernet non Ethernet end devices to the central where UPS is installed for un interrupt power system and power control system 6712 watts Wireless LAN Access Points Museum Sightseeing Airport Hotel Campus Factory and Warehouse can install the Access Point anywhere with no hesitation 10 12 watts IP Surveillance x Enterprise Museum Campus Hospital and Bank f can install I
12. P Camera without limits of installation KR e location It needs no electricians to install AC y sockets 3 12 watts PoE Splitter PoE Splitter splits the PoE 48V DC over the Ethernet cable into 5 12V DC power output It f frees the device deployment from restrictions due to power outlet locations which eliminate the costs for additional AC wiring and reduces the installation time 30 watts High Power Speed Dome FGSD 910HP only x This state of the art design is considerable to fit in Y various network environments like traffic centers i shopping malls railway stations warehouses airports and production facilities for the most wT demanding outdoor surveillance applications no need electrician to install AC sockets Since the FGSD 910P FGSD 910HP per PoE port supports 48V 56V DC PoE power output please check and assure the Powered Device s PD acceptable DC power range is from 48V 56V DC Otherwise it will damage the Powered Device PD 17 1 3 Power over Ethernet Overview What is PoE The PoE is an abbreviation of Power over Ethernet the PoE technology means a system to pass electrical power safely along with data on Ethernet UTP cable The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels but can operate with category 3 cable for low power levels Power is supplied in common mode over two or more of the differential
13. UIPMENT PSE PD SPARE PAIR 1 1 T oxi On 3 3 mie e SIGNAL PAIR SPARE PAIR Figure 3 1 Power Supplied over the Spare Pins 19 1 The data pairs are used Since Ethernet pairs are transformer coupled at each end it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity POWER SOURCING POWERED DEVICE EQUIPMENT PSE PD SPARE PAIR ES Jw ee OC XE 20007 SIGNAL PAIR 7 7 SPARE PAIR Figure 3 2 Power Supplied over the Data Pins 2420 d Troubleshooting This chapter contains information to help you solve issues If the PoE Ethernet Switch is not functioning properly make sure the PoE Ethernet Switch was set up according to instructions in this manual The Link LED is not lit Solution Check the cable connection and remove duplex mode of the PoE Ethernet Switch Performance is bad Solution Check the speed duplex mode of the partner device The PoE Ethernet Switch is run at Auto negotiation mode and if the partner is set to half duplex then the performance will be poor 1000Base T port link LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiatio
14. ernet Switch as shown in Figure 2 5 Figure 2 5 Place the PoE Ethernet Switch on the Desktop Step 2 Place the PoE Ethernet Switch on desktop near an AC power source Step 3 Keep enough ventilation space between the PoE Ethernet Switch and the surrounding objects When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 4 under Specifications Step 4 Connect your PoE Ethernet Switch to 802 3af 802 3at complied Powered Devices PD and other network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports or 10 100 1000 port on the Front of the PoE Ethernet Switch B Connect the other end of the cable to the network devices such as printer servers workstations router etc Connection to the PoE Ethernet Switch requires UTP Category 5 network cabling with RJ 45 tips For more information please see the Cabling Specifications in Appendix A Step 5 Supply power to the PoE Ethernet Switch A Connect one end of the power cable to the PoE Ethernet Switch B Connect the power plug of the power cable to a standard wall outlet When the PoE Ethernet Switch receives power the Power LED should remain solid Green 2 4 Rack Mounting To install the PoE Ethernet Switch in a 19 inch standard rack follow the instructions described below Step 1 Place your PoE Ethernet Switch on a hard flat surface with the front panel pos
15. et 130 watts at room 130 watts at room temperature temperature Max number of Class 1 PD 8 8 Max number of Class 2 PD 8 8 Max number of Class 3 PD 8 8 Max number of Class 4 PD 4 Standard Conformance EMI Safety FCC Class A CE Operating Environment 0 50 degrees C Storage Environment 10 70 degrees C Operating Humidity 5 95 Relative Humidity non condensing Storage Humidity 5 95 Relative Humidity non condensing Standard Compliance IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE 802 3x Flow Control IEEE 802 3af IEEE 802 3at Power over Ethernet High Power over Ethernet FGSD 910HP only Remarks POE Power budget may be reduced if the operating temperature rises 2 Hardware Description This product provides three different running speeds 10Mbps and 100Mbps at port 1 to port 8 10 100 1000Mbps at port 9 and automatically distinguishes the speed of incoming connection This section describes the hardware features of the FGSD 910P FGSD 910HP For easier management and control of the switch familiarize yourself with its display indicators and ports Front panel illustrations in this chapter display the unit LED indicators Before connecting any network device to the FGSD 910P FGSD 910HP please read this chapter carefully 2 1 Front Panel The Front Panel of the FGSD
16. housing suitable for desktop deployment in SOHO office or department network application Perfectly Integrated Solution for IP PoE Camera and NVR System Different from the general IT industrial PoE Switch which usually comes with 12 or 24 PoE ports the FGSD 910P FGSD 910HP provides eight 802 3af 802 3at PoE ports for catering to small scale of IP Surveillance networks at a lower total cost The FGSD 910P FGSD 910HP comes with high performance switch architecture and 130 watt PoE power budget The recorded video files from 8 PoE IP Cameras can be powered by the FGSD 910P FGSD 910HP and saved in the 8 channel NVR system or surveillance software to perform comprehensive security monitoring For instance one FGSD 910P FGSD 910HP can be combined with one 8 Channel NVR 5E and 8 PoE IP cameras as a kit for the administrators to centrally and efficiently manage the surveillance system in the local LAN and the remote site via Internet Easy Cable Connection With data and power over Ethernet from one unit the FGSD 910P FGSD 910HP reduces cabling requirements and eliminates the need for dedicated electrical outlets on the wall ceiling or any unreachable place A wire that carries both data and power can lower the installation costs simplify the installation effort and eliminate the need for electricians or extension cords Providing 8 PoE interfaces the FGSD 910P FGSD 910HP is ideal for small businesses and workgroups req
17. itioned towards your front side Step 2 Attach a rack mount bracket to each side of the PoE Ethernet Switch with supplied screws attached to the package Figure 2 6 shows how to attach brackets to one side of the PoE Ethernet Switch Figure 2 6 Attaching the Brackets to the PoE Ethernet Switch You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invali date the warranty Step 3 Secure the brackets tightly Step 4 Follow the same steps to attach the second bracket to the opposite side Step 5 After the brackets are attached to the PoE Ethernet Switch use suitable screws to securely attach the brackets to the rack as shown in Figure 2 7 KK 068000 0f Figure 2 7 Mounting the PoE Ethernet Switch in a Rack Step 6 Proceeds with Step 4 and Step 5 of session 2 3 Desktop Installation to connect the network cabling and supply power to your PoE Ethernet Switch 2 5 Product Application 2 5 1 802 3af PoE IP Surveillance in Public Transportation Providing up to eight 802 3af 802 3at PoE in line power interfaces and 1 Gigabit TP interface the PoE Ethernet Switch can easily build a power centrally controlled IP Camera system for the enterprises It can work with 8 Channel NVR and surveillance software to perform comprehensive security monitoring For instance one PoE Ethernet Switch can combine with one 8 Channel NVR that is each
18. n may not recognize this type of full duplex setting Why the PoE Ethernet Switch doesn t connect to the network Solution Check the LNK ACT LED on the PoE Ethernet Switch Try another port on the PoE Ethernet Switch Make sure the cable is installed properly and make sure the cable is the right type Turn off the power After a while turn on power again Why I connect my PoE device to PoE Ethernet Switch and it cannot power on Solution 1 Please check the cable type of the connection from the PoE Ethernet Switch port 1 to port 8 to the other end The cable should be an 8 wire UTP Category 5 or above EIA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters will affect the power supply 2 Please check and assure the device is fully complied with IEEE 802 3af standard FGSD 910P 3 Please check and assure the device is fully complied with IEEE 802 3af 802 3at standard FGSD 910HP What is the power output of each PoE port Solution FGSD 910P each PoE port supports 48V DC 350mA max 15 4 watts power output Detect and inject by the standard of IEEE 802 3af FGSD 910HP each PoE port supports 56V DC 600mA max 30 watts power output Detect and inject by the standard of IEEE 802 3at 2 1 Appendix A Networking Connection A 1 PoE RJ 45 Port Pin Assignments PIN NO RJ 45 POWER ASSIGNMENT 1 Power 12345678 2 Power 3 Power 6 Power
19. nection Straight Cable 12345678 Crossover Cable 12345678 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight through and Crossover Cables Please make sure your connected cables are with same pin assignment and color as the above picture before deploying the cables into your network Q PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product 8 Port 10 100Mbps 802 3af PoE 1 Port 10 100 1000Mbps Desktop Switch Model Number FGSD 910P Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN55022 2010
20. pairs of wires found in the Ethernet cables and comes from a power supply within a PoE enabled networking device such as an Ethernet switch or can be injected into a cable run with a mid span power supply The original IEEE 802 3af 2003 PoE standard provides up to 15 4 W of DC power minimum 44 V DC and 350mA to each device Only 12 95 W is assured to be available at the powered device as some power is dissipated in the cable The updated IEEE 802 3at 2009 PoE standard also known as PoE or PoE plus provides up to 25 5 W of power The 2009 standard prohibits a powered device from using all four pairs for power The 802 3af 802 3at define two types of source equipment Mid Span and End Span Mid Span Mid Span device is placed between legacy switch and the powered device Mid Span is tap the unused wire pairs 4 5 and 7 8 to carry power the other four is for data transmit End Span End Span device is directly connecting with powered device End Span could also tap the wire 1 2 and 3 6 PoE System Architecture The specification of PoE typically requires two devices the Powered Source Equipment PSE and the Powered Device PD The PSE is either an End Span or a Mid Span while the PD is a PoE enabled terminal such as IP Phones Wireless LAN etc Power can be delivered over data pairs or spare pairs of standard CAT 5 cabling Powered Source Equipment PSE Power sourcing equipment PSE is a device such as a switch that p
21. rovides sources power on the Ethernet cable The maximum allowed continuous output power per cable in IEEE 802 3af is 15 40 W A later specification IEEE 802 3at offers 25 50 W When the device is a switch it is commonly called an End span although IEEE 802 3af refers to it as endpoint Otherwise if it s an intermediary device between a non PoE capable switch and a PoE device it s called a Mid span An external PoE injector is a Mid span device Powered device A powered device PD is a device powered by a PSE and thus consumes energy Examples include wireless access points IP Phones and IP cameras Many powered devices have an auxiliary power connector for an optional external power supply Depending on the PD design some none or all power can be supplied from the auxiliary port with the auxiliary port sometimes acting as backup power in case of PoE supplied power failure How Power is Transferred Through the Cable A standard CAT5 Ethernet cable has four twisted pairs but only two of these are used for 10BASE T and 100BASE TX The specification allows two options for using these cables for power shown in Figure 3 1 and Figure3 2 The spare pairs are used Figure 3 1 shows the pair on pins 4 and 5 connected together and forming the positive supply and the pair on pins 7 and 8 connected and forming the negative supply In fact a late change to the spec allows either polarity to be used POWER SOURCING POWERED DEVICE EQ
22. sers of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste WEEE has to be collected separately Revision PLANET 8 Port 10 100Mbps 802 3af 802 3at PoE 1 Port 10 100 1000Mbps Desktop Switch User s Manual For Models FGSD 910P FGSD 910HP Revision 1 0 JANUARY 2014 Part No 2351 AK3140 001 Table Of Contents n de 5 1 1 ee TTT 5 1 2 Produce Descriptio Die reremane neie a a a a O 5 13 e He 6 1 4 SPeCCHICATIONS e H 2 Hardware le Le 9 2 Rront PANE riria aae mavens Gne oct ne Del A e ida DE De 9 Zk WED e Mere 9 2 2 Rear Pan l wisiescccecieatirecnaciedaecand aenensctodsbaniafersentanenapianiadenedacaiananianecsane 10 2 3 We E ee EE 12 2 4 Rack Oe ul LEE 13 2 5 Product ele ee 14 2 5 1 802 3af PoE IP Surveillance in Public Transportation 14 2 5 2 IP Office Department Workgroup PoE Switch 16 2 6 Power over Ethernet Powered Device cinere ene tiit nnne ana nain inn 17 3 Power Over Ethernet OVerVIB Wc sse aco gege e geed Eege NEE 18 4 Troubleshootlrigi oui geg sate eet hr ies xen ipie nain p nin aive dai exc ves suede vk axe pecus 21 Appendix A Networking Connection eeeseeen Henne 22 Al PoE RJ 45 Port Pin ASSIGNMENT Sarina rione gEeg ga NEESS EES e 22 A 2 Switch s Data RJ 45 Pin Assignments 1000Mbps 1000Base T 22 A 3 10 100Mbps 1
23. to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Standby mode operation For energy saving please remove the power cable to disconnect the device from the power circuit Without removing power cable the device will still consuming power from the power source In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to remove the power connection for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end u
24. uiring deploying the PoE for the wireless access points IP based surveillance camera or IP phones in any places easily efficiently and cost effectively 1 3 Features E RJ 45 Interface 8 Port 10 100Mbps Fast Ethernet Switch 8 Port supports 48V DC power to PoE Powered Device FGSD 910P 8 Port supports 56V DC power to PoE Powered Device FGSD 910HP 1 Port 10 100 1000Mbps Gigabit Ethernet Switch B Power over Ethernet Complies with IEEE 802 3af 802 3at Power over Ethernet End Span PSE Up to 8 IEEE 802 3af devices powered Supports PoE Power up to 15 4 watts for each PoE port Up to 4 IEEE 802 3at devices powered FGSD 910HP only Supports PoE Power up to 30 watts for each PoE port FGSD 910HP only 130 watt PoE budget Auto detects powered device PD Circuit protection prevents power interference between ports Remote power feeding up to 100m B Switching Port 8 Port 9 ation E Hardware Link Act 1 4 Specifications Integrates address look up engine supporting 4K absolute MAC addresses Automatic address learning and address aging 12 inch desktop size 1U height 1 silent FAN to provide stable and efficient power performance Hardware based 10 100Mbps Auto Negotiation and Auto MDI MDI X Port 1 to Hardware based 10 100 1000Mbps Auto Negotiation and Auto MD
Download Pdf Manuals
Related Search