Home

User`s Manual - CNET Content Solutions

1. 1 E Some types and formats of DVD R DL and DVD R DL discs might be unreadable BH Disc created in DVD R DL format4 Layer Jump Recording cannot be read When writing or rewriting Please observe the following points while you write or rewrite data to a media m Always copy data from the hard disk drive to the optical media Do not use the cut and paste function as the original data will be lost if there is a write error User s Manual 4 10 Do not perform any of the following actions m Change users in the Operating Systems m Operate the computer for any other function including such tasks as using a mouse or Touch Pad or closing opening the display panel m Start a communication application Apply impact or vibration to the computer Install remove or connect external devices including such items as a memory media card USB device external monitor or an optical digital device m Use the audio video control button to reproduce music or voice m Open the optical disc drive Do not use shut down log off Sleep Mode or Hibernation Mode functions while writing or rewriting Make sure that the write rewrite operation is completed before going into either Sleep Mode or Hibernation Mode You can remove an optical media on the optical disc drive after writing is completed If the media is of poor quality or is dirty or damaged writing or rewriting errors might occur Set the computer on a level surface and avoid
2. If Sleep and Charge function is enabled the computer s battery discharges during hibernation or when the computer is turned off Connect the AC adaptor to the computer or disable the Sleep and Charge function Some external devices might not work when connected to a compatible port if the Sleep and Charge function is enabled Reconnect the external device after turning the computer ON If the external device still does not work connect device to an USB port that does not have the Sleep and Charge function or change to disable the Sleep and Charge function Problem Procedure The USB Wakeup When Sleep and Charge function is enabled the function does not USB WakeUp function does not work for ports work that support the Sleep and Charge function In that case use an USB port that does not have the USB Sleep and Charge function or change to disable Sleep and Charge function Sound system In addition to the information in this section also refer to the documentation supplied with your audio device Problem Procedure No sound is heard Press the function keys to increase or decrease volume Check the software volume settings Check to see if Mute is turned to Off Check to make sure that the headphone connection is secure Check within the Windows Device Manager application to ensure that the sound device is enabled and that the device is properly working Annoying sound is In this instance you might be experien
3. Po NS 4 About the JEITA 5GHz Wireless LAN supports W52 W53 W56 Channel IEEE802 11b g n IEEE802 11a n w56 Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low power data communication system radio station stipulated in the Telecommunications Business Law of Japan Intel Centrino Wireless AC 7260 Wireless LAN and Bluetooth The Name of the radio equipment 7260NGW DSP Research Inc Approval Number D130021003 Intel Centrino Wireless N 7260 Wireless LAN and Bluetooth The Name of the radio equipment 7260NGWBN DSP Research Inc Approval Number D130021003 Intel Centrino Wireless AC 3160 Wireless LAN and Bluetooth The Name of the radio equipment 3160NGW DSP Research Inc Approval Number D130092003 Atheros QCNFA335 Wireless Network Adapter b g n and Bluetooth The Name of the radio equipment QCNFA335 DSP Research Inc Approval Number D130158003 Broadcom BCM43142 Wireless Network Adapter b g n and Bluetooth The Name of the radio equipment BCM43142 DSP Research Inc Approval Number D135106201 The following restrictions apply Do not disassemble or modify the device Do not install the embedded wireless module into other device Radio approvals for wireless devices A User s Manual This equipment is approved to the radio standard by the countries regions in the following table If
4. The battery might not begin charging immediately under the following conditions E The battery is extremely hot or cold if the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity charge it at room temperature of between 5 C to 35 C 41 95 F E The battery is nearly completely discharged In this instance leave the AC adaptor connected for a few minutes and the battery should begin charging The DC IN Battery indicator might show a rapid decrease in battery operating time when you try to charge a battery under the following conditions E The battery has not been used for a long time E The battery has completely discharged and been left in the computer for a long time In such cases do the following 1 Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off 4 20 2 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power 3 Charge the battery until the DC IN Battery indicator glows white Repeat these steps two or three times until the battery recovers normal capacity Monitoring battery capacity T Remaining battery power can be monitored using the following methods Clicking the battery icon on the Windows Taskbar Via the Battery Status in the Windows Mobility Center window E Wait at least 16 seconds after turning on the com
5. package FreeType Project and FreeType archive refer to the set of files originally distributed by the authors David Turner Robert Wilhelm and Werner Lemberg as the FreeType Project be they named as alpha beta or final release 7 20 User s Manual You refers to the licensee or person using the project where using is a generic term including compiling the project s source code as well as linking it to form a program or executable This program is referred to as a program using the FreeType engine This license applies to all files distributed in the original FreeType Project including all source code binaries and documentation unless otherwise stated in the file in its original unmodified form as distributed in the original archive If you are unsure whether or not a particular file is covered by this license you must contact us to verify this The FreeType Project is copyright C 1996 2000 by David Turner Robert Wilhelm and Werner Lemberg All rights reserved except as specified below 1 No Warranty THE FREETYPE PROJECT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE OF THE FREETYPE PROJECT 2 Redistribution Thi
6. AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The licence and distribution terms for any publically available version or derivative of this code cannot be changed i e this code cannot simply be copied and put under another distribution licence including the GNU Public Licence FreeType License Issues The FreeType Project LICENSE 2006 Jan 27 Copyright 1996 2002 2006 by David Turner Robert Wilhelm and Werner Lemberg User s Manual 7 19 User s Manual Introduction The FreeType Project is distributed in several archive packages some of them may contain in addition to the FreeType font engine various tools and contributions which rely on or relate to the FreeType Project This license applies to all files found in such packages and which do not fall under their own explicit license The license affe
7. Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Click E Tap the Touch Pad or click the left Touch Pad control button once m Left click the mouse once m Tap the touch screen once only for touch screen models User s Manual 2 1 Right click Double click Charm Desktop Start screen Apps view Click the right Touch Pad control button once Right click the mouse once m Press and hold on the touch screen only for touch screen models E Tap the Touch Pad or click the left Touch Pad control button twice m Left click the mouse twice m Tap the touch screen twice only for touch screen models By swiping in from the right edge only for touch screen models or pointing the mouse pointer to the lower right or upper right corner of your screen you can find a list of charms Search Share Start Devices and Settings Click the Desktop tile from the Start screen to access the desktop You can go back to the Start screen from an app or the desktop by the following ways H Click the Start charm m Move the mouse pointer all the way into the lower left corner of the screen and then click the Start button SH m Use the Windows logo key SH on your keyboard For detailed information please refer to the Windows Help and Support You can find all of your apps including desktop programs in the Apps view To get to the
8. Figure 2 3 Connecting the DC output plug to the computer Product appearance depends on the model you purchased 1 DC IN 19V jack 2 DC output plug 3 Plug the power cord into a live wall outlet The DC IN Battery indicator glows Opening the display The display panel can be opened to a wide range of angles for optimal viewing While holding down the palm rest with one hand so that the main body of the computer is not raised slowly lift the display panel It allows the angle of the display panel to be adjusted to provide optimum clarity Figure 2 4 Opening the display panel S T P Product appearance depends on the model you purchased 1 Display panel Use reasonable care when opening and closing the display panel Opening it vigorously or slamming it shut could damage the computer 1 Be careful not to open the display panel too far as this could put stress J on the display panel s hinges and cause damage H Do not press or push on the display panel B Do not lift the computer by the display panel User s Manual 2 5 amp Do not close the display panel with pens or any other objects left in between the display panel and the keyboard m When opening or closing the display panel place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel Do not use excessive force when opening or closing the display panel Turning on the power This secti
9. Graphics and Media Control Panel You can access this control panel in the following way Right click on the desktop and click Graphics Properties In Intel HD Graphics Control Panel 1 Click Power and select On battery from the drop down menu under Power in the upper left corner 2 Click Disable under Display Power Saving Technology 3 Click Apply If you want to enable this feature click Enable under Display Power Saving Technology In Intel Graphics and Media Control Panel 1 Click Power 2 Select On battery from the drop down menu in Power Source 3 Clear the Display Power Saving Technology check box 4 Click OK If you want to enable this feature under the conditions mentioned above select the Display Power Saving Technology check box AMD Vari Bright User s Manual AMD GPU models might include the AMD Vari Bright feature that can save the computer s power consumption by optimizing picture contrast on the internal LCD This feature can be used if the computer is E running under battery mode H using the internal LCD display only The Vari Bright feature can be enabled in the AMD VISION Engine Control Center Catalyst Control Center You can access the center in the following way H_ Right click on the desktop and click AMD VISION Engine Control Center Catalyst Control Center In this control panel 1 Select PowerPlay under Power 2 Select Enable PowerPlay check box and th
10. LAN jack 2 LAN cable Product appearance depends on the model you purchased 3 Plug the other end of the cable into a LAN hub connector or router Check with your LAN administrator and hardware or software vendor before using or configuring a network connection Memory media A i User s Manual The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices such as digital cameras and Personal Digital Assistants Keep foreign objects out of the memory media slot Never allow metal objects such as screws staples and paper clips to enter the computer or Keyboard Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury An adaptor is required to use miniSD microSD Card Not all memory media have been tested and verified to work correctly Therefore it is not possible to guarantee that all memory media can operate properly 4 25 Figure 4 7 Examples of memory media Qo Secure Digital SD Card microSD card adaptor and microSD card MultiMediaCard MMC Points to note about the memory media card F SD SDHC SDXC memory cards comply with SDMI Secure Digital Music Initiative which is a technology adopted to prevent unlawful copy or playback of digital music For this reason you cannot copy or play back protected material on an
11. Secure Digital and SD are trademarks of SD Card Association MultiMediaCard MMC and eMMC are trademarks of MultiMediaCard Association Blu ray Disc Blu ray BDXL and the logos are trademarks of th e Blu ray Disc Association ATHEROS is a trademark of Qualcomm Atheros Inc registered in the United States and other countries DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS Inc DTS Inc All Rights Reserved Realtek is a registered trademark of Realtek Semiconductor Corporation All other product names and service names in this manual might be trademarks or registered trademarks of their respective companies Regulatory Information FCC information User s Manual FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter
12. The BIOS setup utility will load 3 In the BIOS setup screen select Advanced gt System Configuration gt Boot Mode Note Please skip the following contents if you cannot find the Boot Mode option in your system 4 Select UEFI Boot Default If you set the Boot Mode as CSM Boot the recovery media created by Recovery Media Creator will NOT be able to restore If you create a recovery image using advanced recovery tools from Control Panel also make sure to use the default Boot Mode option UEFI Boot in the BIOS setup utility before restoring 1 Load the Recovery Media into the Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port Click the power icon cy on the Start screen and then select Restart 3 Hold down the F12 key and then release this key one second after the computer is power on 4 Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media 5 A menu is displayed from which you should follow the on screen instructions If you have previously chosen to remove the recovery partition and are trying to create Recovery Media the following message appears The Recovery Media Creator can not be launched because there is no recovery partition When there is no recovery partition the Recovery Media Creator cannot make Recovery Media However if you have already created a Recovery Media you can use it to restore t
13. rkiye Elektrikle ali an ve elektronik ekipmanda belirli tehlikeli maddelerin kullanimiyla ilgili kisitlama y netmeli i gereklerini tamamen yerine getirmektedir m The number of possible pixel failures of your display is defined according to ISO 9241 307 standards If the number of pixel failures is less than this standard they will not be counted as defect or failure Battery is a consumption product since the battery time depends on the usage of your computer If the battery can not be charged at all then it is a defect or failure The changes in battery time is not a defect or failure Following information is only for India The use of this symbol indicates that this product may not be treated as household waste By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please visit our website http www toshiba india com or contact call center 1800 200 8674 These symbols might not stick depending on the country and region where you purchased User s Manual 1 7 Video Standard Notice User s Manual THIS PRODUCT IS LICENSED UNDER THE AVC THE VC 1 AND MPEG 4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR I ENCODING VIDEO IN COMPLIANCE
14. 4 28 External displays allow you to share your desktop or extend the desktop area Connecting an external display T T User s Manual Your computer comes with a built in display but you can also connect other external displays via available ports on the computer E Some models may include the Triple Monitor function that can display image on Triple Monitor independently E As the port operation of all external display devices have not been confirmed some devices might not function properly External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer To connect an external analog monitor do the following 1 Connect the RGB cable to the External RGB monitor port Figure 4 9 Connecting the RGB cable to the External RGB monitor port 1 External RGB monitor port 2 RGB cable Product appearance depends on the model you purchased There are no fastening screws for an external monitor cable on the External RGB monitor port However external monitor cables which have connectors with fastening screws can still be used 2 Turn the external monitor s power on When you turn on the power the computer automatically recognizes the monitor and determines whether it is a color or monochrome device When displaying desktop on an external analog monitor desktop is sometimes displayed on the center of the monitor with black bars around desktop with small size A
15. 8 The Grand Tour Front with the display closed ccsccceseeesseeeseseeeeeeeeesenseeeeeseenenesees 3 1 Left Side oo eeceeeceeeeeeseseeenseeneeeeeeseseceeeaseaueeeeeeesaseeeesseansuseeeeeaseeeesseenaneneeees 3 2 Right Sid sos siissescovescesetebesatustencoteasssueuatetessitectedesauasuicercnesbutuewivestueeediecsdusten 3 3 Bak onnaa aaia aaia 3 5 Underside eeeceeeneeeeeeeeeeeeneeeeeeseeeeeesasaeeeeseeeeneeeeesseeeseseeaeeaseneesseenanenaeen 3 5 Front with the display open 2 ccscss eceeeeeeeeeceeeeeeeeeeeeeeeeeesnaeeeeeeees 3 6 Internal Hardware Components scsscececceeeeeeeeeeeeeseeeneneneeenesees 3 9 Power Condition Descriptions ccccceeeeseeeeeeee sense eeeeeeeeeseeeeeees 3 12 Operating Basics Using the Touch Pag siooni ceeds ceesete i cee teste ek este ce cee te deck cedeeet chewed 4 1 Th Keyb rd ionsar a aa Eiaa adaa 4 2 Optical disc driv S ace civics scuscscve dives dinastiari iaa aaa aaia iaaiiai 4 4 CyberLink PowerDVD for TOSHIBA 2 csc eceeeseeseeeeeeeeeeeeeeeeees 4 11 TOSHIBA Blu ray Disc Player cccceseeeesssceeeeeeeeeeeeeeesseneneseeneneeeeees 4 13 3D Playback on an External 3D Device 2 ceceeeeeeeeeeeeeeeeeeees 4 16 Battery cinduen enanas ranana na aaaea aka anada Eia Ninaa 4 18 LAN i cc eea S A AEE EE E 4 24 Memory Media ssrin alee evades ae eee eee ace 4 25 External Display sivccccscsccistesesesteucenedecssunceendevstnees
16. Apps view m Move the mouse pointer and then click the icon in the lower left corner of the screen H Slide up from the middle of the Start screen only for touch screen models Using your computer for the first time T User s Manual Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer It is intended to help you be more comfortable and productive while using a notebook computer By following the recommendations in it you can reduce your T chance of developing a painful or disabling injury to your hand arms shoulders or neck This section provides basic information to start using your computer It covers the following topics Connecting the AC adaptor Opening the display Turning on the power Initial setup Use a virus check program and make sure that it is updated regularly Never format storage media without checking its content formatting destroys all stored data It is a good idea to back up the internal Hard Disk Drive or other main storage device to external media periodically General storage media is not durable or stable over long periods of time and under certain conditions might result in data loss Before you install a device or application save any data in memory to the Hard Disk Drive or other storage media Failure to do so might result in data loss Connecting the AC adaptor A User s Manual Attach the AC ad
17. Disc Player might not function properly Do not change the screen resolution while running the TOSHIBA Blu ray Disc Player Do not change the display device while running the TOSHIBA Blu ray Disc Player Starting TOSHIBA Blu ray Disc Player Use the following procedure to start TOSHIBA Blu ray Disc Player Insert a Blu ray Movie Disc in the optical disc drive while the operating system is running When a Blu ray Movie Disc is set in the Blu ray drive for models with Blu ray drive TOSHIBA Blu ray Disc Player might start automatically Click TOSHIBA Blu ray Disc Player under TOSHIBA in the Apps view Operating TOSHIBA Blu ray Disc Player Notes on using TOSHIBA Blu ray Disc Player Screen display and available features might vary amongst Blu ray Videos and scenes If the menu is opened in the Display Area using the Control Panel s Top Menu or Menu buttons Touch Pad and mouse menu operations might not be able to be used Open TOSHIBA Blu ray Disc Player Manual TOSHIBA Blu ray Disc Player features and instructions are explained in details in TOSHIBA Blu ray Disc Player Manual Use the following procedure to open TOSHIBA Blu ray Disc Player Manual User s Manual Press the F1 key when TOSHIBA Blu ray Disc Player is launched and click the Help button 3D Playback on an External 3D Device 3D playback on an external 3D device feature is only provided with some models Effect of 3D can be shown only on an ex
18. Europe and China USA United Kingdom UL approved BS approved Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability T User s Manual The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing OFDM radio technology and is compliant to E The IEEE 802 11 Standard on Wireless LANs Revision a b g n b g n or Revision a b g n ac as defined and approved by the Institute of Electrical and Electronics Engineers Bluetooth Modules are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum FHSS radio technology and is compliant to H Bluetooth Specification depending on the model you purchased as defined and approved by the Bluetooth Special Interest Group Logo certification with Bluetooth wireless technology as defined by the Bluetooth Special interest Group This Bluetooth product is not compatible with devices using Bluetooth Version 1 0B specifications The wireless devices have not completed verification of connection and operation with all devices which are using the Wireless LAN or Bluetooth radio technology Bluetooth and Wireless LAN devices operate within the same radio frequency range and might int
19. Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Carefully clean the dust on the surface of the cooling vents using a soft cloth Front with the display open This section shows the computer with the display panel open In order to open the display lift up the display panel and position it at a comfortable viewing angle for you Figure 3 6 The front of the computer with the display panel open SS ES ay E E E E ra LAC User s Manual 3 6 User s Manual Figure 3 7 Top side of the touch screen model 1 Microphone 2 Web Camera LED 3 Web Camera 4 Microphone 8 Display hinges 9 Power button 10 Power indicator 11 Keyboard 5 Wireless communication antennas 12 Touch Pad not shown 6 Display screen 7 Stereo speakers 13 Touch Pad control buttons Provided with some models Product appearance depends on the model you purchased Microphone Web Camera LED Web Camera The built in microphone allows you to import and record sounds for your application Refer to the Sound System and Video mode section for more information The Web Camera LED glows when the Web Camera is operating Web Camera is a device that allows you to record video or take photographs with your computer You can use it for video chat
20. Refer to the Power Condition Descriptions section for further information Problem Procedure AC adaptor does not Check the connections to make sure that the power the computer power cord adaptor is firmly connected to the computer and a working power outlet Check the condition of the cord and terminals If the cord is frayed or damaged it should be replaced while if the terminals are soiled they should be cleaned with a clean cotton cloth If the AC adaptor still does not power the computer you should contact TOSHIBA Support Battery If you suspect a problem with the battery check the status of the DC IN Battery indicator Problem Procedure Battery does not The battery might be discharged Connect the AC power the computer adaptor to recharge the battery User s Manual 6 5 Problem Procedure Battery does not If the battery is completely discharged it will not charge when the AC begin charging immediately In these instances adaptor is attached wait a few minutes before trying again If the battery still does not charge you should check that the power outlet the AC adaptor is connected to its supplying power This can be tested by plugging another appliance into it Check whether the battery is hot or cold to the touch if so it will not charge properly and should be allowed to reach room temperature before you try again Unplug the AC adaptor and remove the battery to make sure its connecting terminals are
21. User s Manual This section describes the types of writable discs Check the specifications of your drive to see the types of discs it can write CDs m CD R discs can be written only once The recorded data cannot be erased or changed BH CD RW discs including multi speed CD RW discs high speed CD RW discs and ultra speed CD RW discs can be recorded more than once DVDs E DVD R DVD R DVD R DL and DVD R DL discs can be written only once The recorded data cannot be erased or changed E DVD RW DVD RW and DVD RAM discs can be recorded more than once Blu ray discs E BD R BD R DL BD R TL and BD R QL discs can be written only once The recorded data cannot be erased or changed E BD RE BD RE DL and BD RE TL discs can be recorded more than once Writing discs User s Manual You can use the DVD Super Multi drive to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW or DVD RAM discs You can use the Blu ray Writer drive to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW DVD RAM BD R BD R DL BD RE or BD RE DL discs You can use the Blu ray Writer drive BDXL to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW DVD RAM BD R BD R DL BD RE BD RE DL BD R TL BD R QL or BD RE TL discs When writing information to media using an optical drive you should always ensure that you connect the AC adaptor t
22. User s Manual When the power in the battery pack becomes low the DC IN Battery indicator flashes amber to indicate that only a few minutes of battery power remain If you continue to use the computer while the DC IN Battery indicator flashes the computer enters Hibernation Mode so that you do not lose any data and automatically turn itself off You must recharge a battery pack when it becomes discharged Procedures To recharge a battery pack connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet The DC IN Battery indicator will glow amber while the battery is being charged User s Manual Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack Never attempt to charge the battery pack with any other charger Charging Time The following table shows the approximate time required to charge an exhausted battery fully Battery type Power off Power on Battery pack 24Wh 3 about 3 hours about 3 5 hours cell Battery pack 48Wh 6 about 3 hours about 3 5 hours cell Battery pack 66Wh 6 about 4 hours about 4 6 hours cell high capacity Be aware that the charging time when the computer is on is affected by ambient temperature the temperature of the computer and how you are using the computer If you make heavy use of external devices for example the battery might scarcely charge at all during operation Battery charging notice
23. WITH THE ABOVE STANDARDS VIDEO AND OR II DECODING AVC VC 1 AND MPEG 4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM ENERGY STAR Program D ENERGY STAR Your Computer model may be ENERGY STAR compliant If the model you purchased is compliant it is labeled with the ENERGY STAR logo on the computer and the following information applies TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes To conserve energy your computer is set to enter the low power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode TOSHIBA recommends that you leave this and other energy saving features active so that your computer will operate at its maximum energy efficiency You can wake the computer from Sleep Mode by pressing the power button Your ENERGY
24. battery is charging Power indicator User s Manual White No light Indicates that the AC adaptor is connected and the battery is fully charged Under any other conditions the indicator does not light If the battery pack becomes too hot while it is being charged the charge stops and the DC IN Battery indicator goes out When the temperature of the battery pack falls to a normal range charging will resume This process occurs regardless of whether the computer s power is on or off Check the Power indicator to determine the power status of the computer The following indicator conditions should be noted White Flashing white No light Indicates that power is being supplied to the computer and the computer is turned on Indicates that the computer is in Sleep Mode and that there is sufficient power available AC adaptor or battery to maintain this condition Under any other conditions the indicator does not light Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that must be taken when using it Using the Touch Pad The Touch Pad located in the palm rest might support the following gestures Tap a A Two Finger Tap i f Pinch or stretch NN t O Swipe Two Finger Scroll User s Manual Tap once on the Touch Pad to activate an item such as an app Tap once on the Touch Pad with two finger
25. be used to playback 2D video contents of Blu ray Disc or AVCHD in 3D using real time 2Dto3D conversion E The 3D playback function of the Player is meant for only personal home use Take note that applicable copyright laws might prohibit the public display when you offer 3D viewing of third party video contents to unidentified personels or mass public H The 2Dto3D conversion function uses TOSHIBA s original algorithm to apply a 3D effect to your own 2D videos However note that this function does not provide the same video content as a video originally provided in 3D and does not create a new video in the 3D format but only plays 2D videos in a 3D like mode User s Manual 4 16 User s Manual The picture generated by 2Dto3D conversion function is not the same as a picture produced for 3D playback use The 2Dto3D conversion function simply uses TOSHIBA s original algorithm to apply pseudo 3D effect to the 2D content The Player is set by default in the 2D format By pressing the 2Dto3D conversion function button you decide to activate the 2Dto3D conversion function and therefore decide to watch your 2D content in 3D The Player will not run the 2Dto3D conversion function automatically Please see the warnings in this section as regards potential copyright infringement and confirm you have any necessary authorization The Player is intended for playing DVD Video DVD VR and video files and for viewing 2D home video content and other 2D c
26. clean if necessary wipe them with a soft dry cloth lightly dipped in alcohol Connect the AC adaptor and replace the battery taking care to ensure that it is securely seated in the computer Check the DC IN Battery indicator If it does not glow allow the computer to charge the battery for at least twenty minutes If the DC IN Battery indicator starts to glow after this period allow the battery to continue to charge for at least another twenty minutes before turning on the computer However if the indicator still does not glow the battery might be at the end of its operating life and should be replaced However if you do not believe the battery is at the end of its operating life you should speak to TOSHIBA Support Battery does not If you frequently recharge a partially charged power the computer battery the battery might not charge to its full as long as expected potential In these instances fully discharge the battery and then attempt to charge it again Check the Power saver option under Choose or customize a power plan in the Power Options User s Manual 6 6 Real Time Clock Problem The BIOS setting and system date time are lost Keyboard Procedure The lasting time of the Real Time Clock RTC has run out You must set the date and time in the BIOS setup utility by using the following steps 1 Click the power icon l on the Start screen and then select Restart 2 Hold down the F2 key and t
27. conditions m When the CAPS LOCK indicator glows the keyboard produces capitals when any letter is typed When the NUM LOCK indicator glows the ten key allows you to enter numbers Figure 4 1 Keypad indicators SS Sy I Se SSeS SS E E 1 CAPS LOCK indicator 2 NUM LOCK indicator CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format NUM LOCK When the NUM LOCK indicator glows you can use the number keys on the keyboard for number entry Function Key The function keys F1 F12 are the twelve keys at the top of your keyboard User s Manual 4 2 User s Manual You can configure the function keys mode as Special function mode or Standard F1 F12 mode by clicking System Settings gt Keyboard under TOSHIBA group in the Apps view Special function mode allows you to use special functions without pressing the FN key Special Standard F1 Function function mode F12 mode F1 FN F1 Launches the help file supplied with the software F2 FN F2 Decreases the brightness of the display panel in individual steps F3 FN F3 Increases the brightness of the display panel in individual steps F4 FN F4 Changes the active display device To use a simultaneous mode you must set the resolution of the internal display panel to match the resolution of the external display device F5 FN F5 Enables or d
28. cool before moving it Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged Pressure or impact damage Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer s components or otherwise cause it to malfunction Cleaning the computer A To help ensure long trouble free operation keep the computer free of dust and dirt and use care with all liquids around it Be careful not to spill liquids into the computer If the computer does get wet turn the power off immediately and let the computer dry completely In these circumstances you should get the computer inspected by an authorized service provider in order to assess the scope of any damage Clean the plastics of the computer using a cloth slightly dampened with water You can clean the display screen by spraying a small amount of glass cleaner onto a soft clean cloth and then wiping the screen gently with the cloth Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer User s Manual Moving the computer While the computer is designed for flexible day to day usage you should exercise a few simple precautions when moving it in order to help ensure trouble free operation Make sure all disk disc activity has ended before moving the computer Turn off shut down
29. display TV you need a 3D enabled display TV that has an HDCP compliant HDMI port 3D video content can only be displayed on an external display connected using HDMI with 3D 3D Settings can be changed on the Settings Screen but the default settings are highly recommended Changing the settings may cause the 3D stereoscopic effect to become stronger which in turn might cause eye fatigue Battery B The 3D effect differs between individuals Refrain from or stop viewing and check your equipment settings if you can see doubly substituted video images or cannot feel the 3D stereoscopic effect when watching 3D video images Still if you cannot see correctly refrain from or stop viewing Refrain from or stop viewing if you feel ill or experience discomfort before or while watching 3D video images H Position yourself directly in front of the display when watching 3D video images And take regular breaks in between m Due to the possibility of impact on vision development viewers of 3D video images should be aged 6 or older Consider whether it is suitable or is there a need for limiting the viewing time before allowing your child to watch a 3D content Hs This software does not have parental lock for 3D video viewing Use the login password functions of Windows if you are worried about the effect of 3D playback on your child s visual function E This software can playback MPEG2 MP4 and WTV files Your own 2D video content
30. foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Optical disc drive The computer might be configured with a DVD Super Multi drive or Blu ray Writer drive 2 6GB and 5 2GB DVD RAM media cannot be read from or written to Right side User s Manual The following figure shows the right side of the computer Figure 3 3 The right side of the computer seq 0000000070000000 1 Headphone jack 5 HDMI out port 2 Microphone jack 6 LAN jack 3 Universal Serial Bus USB 3 0 port 7 External RGB monitor port 4 Universal Serial Bus USB 3 0 port 8 Cooling vents Product appearance depends on the model you purchased Headphone jack A 3 5 mm mini headphone jack enables connection of stereo headphones i HDMI A O User s Manual Microphone jack A 3 5 mm mini microphone jack enables connection of a mini jack for monaural microphone input The integrated sound system provides support for the computer s internal speakers and microphone as well as allowing an external microphone and headphones to be connected via the appropriate jacks Universal Serial Bus Two Universal Serial Bus ports which comply to USB 3 0 ports the USB 3 0 standard are provided on the right side of the computer The USB 3 0 port is compliant with US
31. gt Adjust resolution under Windows System in the Apps view The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window The memory module is installed in the computer Legal Footnote Memory Main System For more information regarding Memory Main System please refer to the Legal Footnotes section Graphics Processing Unit Graphics processing unit GPU performance might vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and might decrease considerably when operating in battery power mode Legal Footnote Graphics Processing Unit GPU For more information regarding Graphics Processing Unit GPU please refer to the Legal Footnotes section Intel Display Power Saving Technology User s Manual Intel GPU models might include the Display Power Saving Technology feature that can save the power consumption of the computer by optimizing picture contrast on the internal LCD This feature can be used if the computer is E running under battery mode H using the internal LCD display only The Display Power Saving Technology feature is enabled as the factory default If you want to disable this feature you can disable it The Display Power Saving Technology feature can be disabled in the Intel HD Graphics Control Panel Intel
32. gt 3 280 feet above sea level muse of computer at temperatures outside the range of 5 C to 30 C 41 86 F or gt 25 C 77 F at high altitude all temperature references are approximate and might vary depending on the specific computer model contact TOSHIBA support for details CPU performance might also vary from specifications due to design configuration Under some conditions your computer product might automatically shut down This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions in your product documentation Contact TOSHIBA technical service and support refer to TOSHIBA support section for more information 64 Bit Computing Certain 32 bit device drivers and or applications might not be compatible with a 64 bit CPU operating system and therefore might not function properly Memory Main System Part of the main system memory might be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities The amount of main system memory allocated to support graphics might vary depending on the graphics system applications u
33. in the BIOS setup utility Refer to Troubleshooting for further information Care and use of the battery pack i This section provides the important safety precautions in order to handle your battery pack properly Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions m Make sure the battery is securely installed in the computer before attempting to charge the battery pack Improper installation could generate smoke or fire or cause the battery pack to rupture m Keep the battery pack out of reach of infants and children It can cause injury E The battery pack can explode if not replaced used handled or disposed of properly Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements E Charge the battery pack only in an ambient temperature from 5 through 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened H Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor Never remove the battery pack while the computer is in Sleep Mode as data could be lost Never remove the battery pack while the Wake up on LAN function is enabled as data will be lost Before you remove a battery pack disable the Wake up on LAN function Charging the batteries
34. indicator 3 12 Display automatic power off 5 5 hinges 3 8 opening 2 5 screen 3 8 Documentation list 2 1 Dual Pointing Device Touch Pad 6 9 DVD Super Multi drive using writing Equipment checklist 2 1 External monitor problems 6 14 Graphics Processing Unit 3 10 Hard disk drive automatic power off 5 5 Keyboard function keys 4 2 Function keys F1 F12 4 2 problems 6 7 Windows special keys 4 4 Index 1 User s Manual LAN cable types 4 24 connecting 4 24 Media care Card care 4 27 Memory card care 4 27 memory media card inserting 4 27 removing 4 28 Memory media slot 4 25 Moving the computer 1 13 MultiMediaCard removing 4 28 Password power on 5 5 Starting the computer by password 5 8 Supervisor 5 8 user 5 7 Pointing Device Touch Pad 3 8 Power conditions 3 12 Hibernation Mode 2 11 panel on off 5 5 Shut Down mode 2 8 Sleep Mode 2 9 turning off 2 8 S turning on 2 6 Problems AC power 6 5 Analyzing the problem 6 2 Battery 6 5 Dual Pointing device 6 9 External monitor 6 13 Hardware and system checklist 6 4 HDD 6 8 Internal display panel 6 7 Keyboard 6 7 Memory Media Card 6 9 Overheating power down 6 5 Power 6 4 Real Time Clock 6 7 Sound system 6 13 TOSHIBA support 6 16 Touch Pad 6 9 USB device 6 11 USB mouse 6 10 Recovery hard disk drive 5 16 Recovery Media 5 15 Restarting the computer 2 9 SD SDHC SDXC Card formatting 4 26 note 4 26 Security lock 4 32 Sle
35. loss 3 Click the power icon c on the Start screen and then select Shut down 4 Turn off any peripheral devices connected to your computer Do not turn the computer or peripheral devices back on immediately Wait a short period to avoid any potential damage Restarting the computer Certain conditions require that you reset the computer for example if m You change certain computer settings To restart the computer there are several ways this can be achieved BH Click the power icon on the Start screen and then select Restart E Inthe Settings charm click Power and then select Restart m Press CTRL ALT and DEL simultaneously once to display the menu window and then select Restart by clicking the power icon in the lower right corner Sleep Mode User s Manual If you have to interrupt your work you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode In this mode data is maintained in the main memory of the computer so that when you turn on the power again you can continue working right where you left off When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled always shut down the computer This includes turning off any wireless communication functionalities and canceling settings that reactivate the computer automatically such as a timer recording function Failure to shut
36. no obstruction Remove any foreign object Check whether the disc is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner For further information refer to Operating Basics Problem Memory media card error occurs You cannot write to a memory media card You cannot read a file Pointing device User s Manual Procedure Remove the memory media card from the computer and then reinsert it in order to ensure that it is firmly connected If the problem persists then you should refer to the documentation supplied with your memory media card for further information Remove the memory media card from the computer and check to ensure that it is not write protected Check to ensure the required file is actually on the memory media card that is inserted into the computer If you are still unable to resolve the problem contact TOSHIBA Support If you are using a USB mouse also refer to both the USB mouse section and the documentation supplied with your mouse Touch Pad Problem The Touch Pad does not work Procedure Check the Device Select settings Click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view 6 9 Problem On screen pointer does not respond to pointing device operation Double tapping Touch Pad does not work The on screen pointer moves too fast or too slow The reaction of Touch Pad is either too sensitive
37. one or more external displays are connected the operating system can automatically detect identify and set up the display settings You can also manually manage how the external displays will work and change the display settings by pressing P while holding down the Windows HH key If you disconnect the external display before you turn off the computer s power be sure to switch to the internal display Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft The computer has a security lock slot on its left side into which you can attach one end of the security cable while the other end attaches to a desk or similar object The methods used for attaching security cables differ from product to product Refer to the instructions for the product you are using for more information Connecting the security lock In order to connect a security cable to the computer do the following 1 Turn the computer so its left side faces you 2 Align the security cable with the lock slot and secure it in place User s Manual 4 32 Figure 4 11 Security lock 1 Security lock slot 2 Security lock Product appearance depends on the model you purchased Optional TOSHIBA Accessories To make your computer even more powerful and convenient to use you can add a number of options and accessories For reference the following list details some of th
38. one or more of the following phrases to refer to this software in your documentation or advertising materials FreeType Project FreeType Engine FreeType library or FreeType Distribution As you have not signed this license you are not required to accept it However as the FreeType Project is copyrighted material only this license or another one contracted with the authors grants you the right to use distribute and modify it Therefore by using distributing or modifying the FreeType Project you indicate that you understand and accept all the terms of this license 4 Contacts There are two mailing lists related to FreeType E freetype nongnu org Discusses general use and applications of FreeType as well as future and wanted additions to the library and distribution If you are looking for support start in this list if you haven t found anything to help you in the documentation m freetype devel nongnu org Discusses bugs as well as engine internals design issues specific licenses porting etc Our home page can be found at http www freetype org 7 22 Index User s Manual AC adaptor additional 4 33 connecting 2 3 DC IN 19V jack 3 2 ASCII characters 4 4 Battery extending life 4 22 monitoring capacity 4 21 save mode 5 5 Battery indicator Battery pack replacing 4 22 Bluetooth 7 7 Cleaning the computer 1 12 Cooling vents 3 5 3 6 DC IN indicator 3 2 DC IN Battery
39. or not sensitive enough USB mouse Problem On screen pointer does not respond to mouse operation Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK Adjust the touch Sensitivity To access it click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view If you are still unable to resolve the problem contact TOSHIBA Support Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure that it is firmly attached Problem Double clicking does not work The on screen p
40. the computer Disconnect the AC adaptor and all peripherals before moving the computer Close the display panel Do not pick up the computer by its display panel Before carrying your computer shut it down disconnect the AC adaptor and allow it to cool down A failure to follow this instruction might result in minor heat injury Do not expose the computer to rapid temperature changes for example in a situation where you carry the computer from a cold environment to a warm room Do not turn on the power until condensation disappears Be careful not to subject the computer to impact or shock A failure to follow this instruction could result in damage to computer computer failure or loss of data Never transport your computer with any cards installed This might damage either the computer and or the card resulting in computer failure Always use a suitable carry case when transporting the computer When carrying your computer be sure to hold it securely so that it does not fall or hit anything Do not carry your computer by holding any of its protruding elements Mobile phones Be aware that the use of mobile phones can interfere with the audio system The operation of the computer will not be impaired in any way but it is recommended that a minimum distance of 30 cm is maintained between the computer and a mobile phone that is in use Instruction Manual for Safety and Comfort All important information on the safe and proper
41. to both the device documentation and the operating system documentation User s Manual Sleep and Charge function For more information and settings refer to the USB Sleep and Charge section Problem cannot use the Sleep and Charge function The battery depletes quickly even when turned OFF the power of the computer External devices connected to the compatible ports do not work when connected to a compatible port Procedure Sleep and Charge function might be disabled Enable the Sleep and Charge function in the TOSHIBA System Settings When there is a current overflow of the external device connected to the compatible port USB bus power DC5V supply might be stopped for safety reasons When this happens disconnect an external device if some external devices are connected After that turn the power of the computer ON OFF to restore the function If this function cannot be still used even if only one external device is connected stop using the external device because its current is over the acceptable value of this computer Some external devices might not be able to use the Sleep and Charge function In this case please try one or more of the following methods m Turn OFF the computer while external devices are connected m Connect external devices after turning OFF of the computer If this function cannot be still used change the setting to disable the function and stop using this function
42. use of this computer is described in the enclosed Instruction Manual for Safety and Comfort Be sure to read it before using the computer Safety Icons Safety icons are used in this manual to bring important information to your attention Each type of message is identified as follows User s Manual User s Manual Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions A caution informs you that improper use of equipment or failure to follow instructions might cause data loss equipment damage or might result in minor or moderate injury Please read A note is a hint or advice that helps you make best use of your equipment Chapter 2 Getting Started This chapter provides an equipment checklist and basic information to start using your computer If you use an operating system that was not pre installed by TOSHIBA some of the features described in this manual might not function properly Equipment checklist Carefully unpack your computer taking care to save the box and packaging materials for future use Hardware Check to make sure that you have all the following items mH TOSHIBA Portable Personal Computer m AC adaptor and power cord 2 pin plug or 3 pin plug Documentation QuickStart H Instruction Manual for Safety and Comfort BH Warranty Information If any of the items are missing or damaged contact your dealer immediately
43. writing to discs refer to the Writing discs section To load discs do the following 1 When the computer s power is on press the eject button to open the disc tray slightly 2 Grasp the disc tray gently and pull until it is fully opened Figure 4 2 Pressing the eject button and pulling the disc tray open Product appearance depends on the model you purchased 1 Eject button 2 Disc tray User s Manual 4 5 T User s Manual 3 Lay the disc label side up in the disc tray Figure 4 3 Inserting a disc 1 Laser lens When the disc tray is fully opened the edge of the computer covers the disc tray slightly Therefore you must turn the disc at an angle when you place it in the disc tray After seating the disc however make sure it lies flat E Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment E Prevent foreign objects from entering the drive Check the surface of the disc tray especially the area behind the front edge of the disc tray to make sure there are no such objects before closing the drive 4 Press gently at the center of the disc until you feel it click into place The disc should lie below the top of the spindle flush with the spindle base 5 Push the center of the disc tray to close it Press gently until it locks into place If the disc is not seated properly when the disc tray is closed the disc might be damaged Also the disc tray might no
44. your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE TOSHIBA will NOT be held responsible for any loss of any data any loss of use or access to your HDD or for any other losses to you or any other person or organization that result from the loss of access to your HDD If you cannot accept this risk do not register the HDD User Password m When saving the HDD User Password shut down or restart the computer If the computer is not shut down or restarted the saved data might not be correctly reflected For more information on shutting down or restarting the computer refer to Turning on the power Supervisor Password If you set a Supervisor Password some functions might be restricted when a user logs on with the User Password To set a Supervisor Password Click Password Utility gt Supervisor Password under TOSHIBA group in the Apps view This utility lets you do the following m Register or delete the Supervisor Password H Specify restrictions for general users Starting the computer using a password i User s Manual If you have already registered a user password there is one way to start the computer E Enter the password manually The password is necessary only if the computer was shut down in Hibernation mode or boot mode It is not needed in Sleep mode and Restart To enter a password manually do the following 1 Turn on the power as described in the Getting Started section The following messa
45. 1998 2011 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Avww openssl org 4 The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission For written permission please contact openssl core openssl org 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project User s Manual 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Awww openssl org THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND A
46. 49 583 3000 This information is only applicable for the countries regions where it is T required EU Declaration of Conformity This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA EUROPE GMBH Hammfelddamm 8 41460 Neuss Germany The complete and official EU Declaration of Conformity can be found on TOSHIBA s web site http epps toshiba teg com on the Internet CE compliance This product is labeled with the CE Mark in accordance with the applicable European Directives notably RoHS Directive 2011 65 EU Radio User s Manual 1 3 User s Manual Equipment and Telecommunications Terminal Directive 1999 5 EC Ecodesign Directive 2009 125 EC ErP and the related implementing measures This product and the original options are designed to observe the related EMC Electromagnetic Compatibility and safety standards However TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented In this case the persons who have connected implemented those options cables have to provide assurance that the system PC plus options cables still fulfils the required standards To avoid general EMC problems the following guidance should be noted H Only CE marked options should be connected implemented m Only best shielded cables should be connected Working environment T
47. B 3 0 standard and backward compatible with USB 2 0 devices The port with the icon 4 has Sleep and Charge function USB 3 0 port s might work as USB 2 0 port s when operating in USB Legacy Emulation mode Note that it is not possible to confirm the operation of all functions of all USB devices that are available Some functions associated with a specific device might not operate properly HDMI out port HDMI out port can connect with Type A connector HDMI cable LAN jack This jack lets you connect to a LAN The adaptor has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Refer to Operating Basics for details Do not connect any cable other than a LAN cable to the LAN jack It could cause damage or malfunction External RGB monitor This port provides 15 pin analog RGB port port Refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment This port allows you to connect an external RGB monitor to the computer Cooling vents The cooling vents help the processor to avoid overheating AN Do not block the cooling vents Keep foreign metal objects such as screws Staples and paper clips out of the cooling vents Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in seriou
48. BA Manual CyberLink PowerDVD for TOSHIBA features and instructions are detailed in CyberLink PowerDVD for TOSHIBA Help Use the following procedure to open CyberLink PowerDVD for TOSHIBA Help Press the F1 key when CyberLink PowerDVD for TOSHIBA is launched TOSHIBA Blu ray Disc Player Please be aware of the following limitations when you use TOSHIBA Blu ray Disc Player Notes on Use User s Manual This software can only be used on Windows operating system TOSHIBA Blu ray Disc Player is only provided with models configured with a Blu ray Writer drive Playback of high bit rate content might cause frame dropping audio skipping or decrease in computer performance Close all other applications before playing back video Do not open any other applications or carry out any other operations during video playback Do not switch to Hibernation or Sleep Mode when running the TOSHIBA Blu ray Disc Player Because Blu ray Disc playback operates according to programs built into the content operation methods operation screens sound effects icons and other features might vary from disc to disc For more information on these items refer to instructions included with content or contact the content manufacturers directly User s Manual Make sure to connect the AC adapter of the computer when playing a video TOSHIBA Blu ray Disc Player supports AACS Advanced Access Control System copy protection technology Renewal of the AACS
49. MHz Revision a and n E Band 2 4 GHz 2400 2483 5 MHz Revision b g and n The range of the wireless signal is related to the transmit rate of the wireless communication Communications at lower transmit range might travel larger distances E The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials H Range is also impacted due to obstacles in the signal path of the radio that might either absorb or reflect the radio signal Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5 15 to 5 25GHz frequency range High power radars are allocated as primary users i e priority users of the bands 5 25 to 5 35GHz and 5 65 to 5 85GHz and that these radars could cause interference and or damage to LE LAN devices Bluetooth wireless technology User s Manual Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers printers and mobile phones When it is enabled Bluetooth provides the wireless personal area network environment which is safe and trustworthy that is quick and easy You cannot use the built in Bluetooth functions of the computer and an external Bluetooth adaptor simultaneously For reference Bluetooth wireless technology has the following features Security Two advanced security mec
50. NY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE This product includes cryptographic software written by Eric Young eay cryptsoft com This product includes software written by Tim Hudson tijn cryptsoft com Original SSLeay License Copyright C 1995 1998 Eric Young eay cryptsoft com All rights reserved This package is an SSL implementation written by Eric Young eay cryptsoft com The implementation was written so as to conform with Netscapes SSL This library is free for commercial and non commercial use as long as the following conditions are aheared to The following conditions apply to all code found in this distribution be it the RC4 RSA Ihash DES etc code not just the SSL code The SSL documentation included with this distribution is covered by the same copyright terms except that the holde
51. Restart 2 Hold down the corresponding key and then release this key one second after the computer is power on 3 Follow the on screen instructions to proceed Hardware and system checklist This section discusses problems caused by your computer s hardware or attached peripherals Basic problems might occur in the following areas E Power m USB device E Keyboard E Sound system E Internal display panel E External monitor H Hard Disk Drive E LAN E Optical Disc Drive E Wireless LAN m Memory Media Card E Bluetooth E Pointing Device Power User s Manual When the computer is not plugged into an AC power outlet the battery pack is the primary power source Your computer also has Real Time Clock RTC function All of the power resources are interrelated with anyone having the ability to produce apparent power problems Overheating power down If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory is lost Problem Procedure Computer shuts Leave the computer off until it reaches room down automatically temperature If the computer has reached room temperature and it still does not start or if it starts but shuts down quickly contact TOSHIBA Support AC power If you have trouble turning on the computer with the AC adaptor connected check the status of the DC IN Battery indicator
52. STAR certified computer should be set by default to enter a low power sleep mode after a period of inactivity Simply touching the mouse or keyboard wakes the computer in seconds These sleep features can save you up to 23 per year 200 kWh per year in electricity and prevent up to 300 pounds of greenhouse gas emissions annually To learn how to adjust or activate these sleep settings on your computer please go to www energystar gov sleepinstructions To activate sleep settings organization wide quickly and easily through network tools please go to www energystar gov powermanagement Disposing of the computer and the computer s batteries User s Manual Discard this computer in accordance with applicable laws and regulations For further information contact your local government This computer contains rechargeable batteries After repeated use the batteries will finally lose their ability to hold a charge and you will need to replace them Under certain applicable laws and regulation it may be illegal to dispose of old batteries by placing them in the trash H Please be kind to our shared environment Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly Optical disc drive safety instructions F Be sure to check the precautions at the end of this section AN m The drive model employs a laser system To ensure proper use of this product please
53. TOSHIBA Leading Innovation gt gt gt User s Manual C70 B L70 B S70 B P70 B X70 B Table of Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 User s Manual TOSHIBA Legal Regulatory and Safety Copyright Disclaimer and Trademarks 2 c cceseeeeeeeeeeeeeeeeeeeees 1 1 Regulatory Information sic cccc cscecetesceceetiecstececestectcetesendteestecendteccteesseseen 1 2 Video Standard Notice cecccccseeceeeeneeeeeeeesseneeeseeeeeseeeseesoeesseeenseenes 1 8 ENERGY STAR Program cccceeeeeeseneeeeseeeeseeeeeeeeeseeeeeeeenseeeeeseeeenesaees 1 9 Disposing of the computer and the computer s batteries 1 9 Optical disc drive safety instructions 00 0 eeeeeeseeeeeeeeeneeeeeeneeneeeees 1 10 General Precautions cccccesseeeseeeeeseeeseeeneeeeeeeseseeeeeeseneeeeeeeenesneeenss 1 11 Safety ICONS oicisssccccssccecesaeeceseecvacedacesceedassceresieesenateedsumeeed sav dddenedeuduaneress 1 13 Getting Started Equipment checklist cl ii su scc ae pees sail ea cia na ck attache sagt ep eeadeeedi nnmnnn nne 2 1 CONVENTIONS ociiiiniec cose ccete nce daaneveetnvecseeeetuadecendtiesdunendrvcenetdenteduianceesadinenteuee 2 1 Using your computer for the first time cccceseeseeeeesseeeeeseeeeeeeeees 2 2 Getting to know WINKOWS cceeeeeeseeee sence ee seeeeenseneeeneeesneneeeenenneeeenees 2 7 Turning Off the POWER ccccceeesneneseeeesseeeeeseeneneseeesnseeeeseeeeeeseeeesnseneeenes 2
54. a clean dry cloth or if this fails with a good quality LCD screen cleaner In this latter instance you should always follow the instructions with the screen cleaner and always ensure that you let the display panel dry properly before closing it Procedure Check to see whether there is a disc in the optical disc drive if so remove it and try to start the computer again If this has no effect check the Boot Priority Options setting within the TOSHIBA System Settings The files on the Hard Disk Drive might be fragmented In this instance run the disk Defragmentation utility to check the condition of your files and the Hard Disk Drive Refer to the operating system s documentation or online Help File for further information on operating and using the Defragmentation utility As a last resort reformat the Hard Disk Drive and then reload the operating system and all other files and data If you are still unable to resolve the problem contact TOSHIBA Support For further information refer to Operating Basics User s Manual Memory Media Card Problem You cannot access a CD DVD Blu ray Disc in the drive Procedure Make sure the drive s disc tray is securely closed Press gently until it clicks into place Open the disc tray and make sure the disc is properly seated It should lie flat with the label facing up A foreign object in the disc tray could block laser light from reading the disc Make sure there is
55. able types The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures If you are using Gigabit Ethernet LAN 1000 megabits per second 1000BASE T be sure to connect with a CAT5e cable or higher You cannot use a CAT3 or CAT5 cable If you are using Fast Ethernet LAN 100 megabits per second 100BASE TX be sure to connect with a CAT5 cable or higher You cannot use a CAT3 cable If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or higher cable Connecting the LAN cable User s Manual To connect the LAN cable do the following 4 24 E Connect the AC adaptor before connecting the LAN cable The AC adaptor must remain connected during LAN use If you disconnect the AC Adaptor while the computer is accessing a LAN the system might hang up E Do not connect any other cable to the LAN jack except the LAN cable Otherwise malfunctions or damage mightoccur E Do not connect any power supplying device to the LAN cable that is connected to the LAN jack Otherwise malfunctions or damage might occur 1 Turn off the power to all external devices connected to the computer 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Figure 4 6 Connecting the LAN cable 1
56. afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux Les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c a d qu ils ont la priorit pour les bandes 5 25 5 35GHz et 5 65 5 85GHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met USA Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Refer to the FCC information section for the detailed information The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits Nevertheless the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized In the usual operating configuration the distance between the antenna and the user should not be less than 20cm Please refer to the computer user s manual for the details regarding antenna location User s Manual The installer of this radio equipment must ensure that the antenna i
57. any error messages against the operating system documentation A Hardware If you cannot find a software problem you should then check the setup and configuration of your hardware First run through the items in the preliminary checklist as described previously then if you still cannot correct the problem try to identify the source The next section provides checklists for individual components and peripherals Before using a peripheral device or application software that is not an authorized TOSHIBA part or product make sure that the device or software can be used with your computer Use of incompatible devices might cause injury or might damage your computer If something goes wrong User s Manual Your computer does not respond to the keyboard commands If an error occurs and the computer does not respond to your keyboard commands do the following Press the power button and hold it down for five seconds Once the computer has turned itself off wait 10 15 seconds before turning on the power again by pressing the power button Your program stops responding If you are working with a program that suddenly freezes all operations chances are the program has stopped responding You can exit the failed program without shutting down the operating system or closing other programs To close a program that has stopped responding 1 Press CTRL ALT and DEL simultaneously once then click Task Manager The Windows Task Manager
58. aptor when you want to charge the battery or operate from AC power It is also the fastest way to get started because the battery pack must be charged before you can operate from battery power The AC adaptor can automatically adjust to any voltage ranging from 100 volts to 240 volts and to a frequency of either 50 hertz or 60 hertz enabling you to use this computer in almost any country region The adaptor converts AC power to DC power and reduces the voltage supplied to this computer E Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor H Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit Failure to do so could result in a fire or electric shock possibly resulting in serious injury Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use Failure to do so could result in a fire or electric shock possibly resulting in serious injury The supplied power cord conforms to safety rules and regulations in the region the computer is bought and sh
59. ards to liquids or store in humid areas or lay media close to containers of liquid Do not touch the metal part of a card or expose it to liquids or let it get dirty m After using card return it to its case The card is designed so that it can be inserted only one way Do not try to force the card into the slot E Do not leave a card partially inserted in the slot Press the card until you hear it click into place H Set the write protect switch to the lock position if you do not want to record data E Memory cards have a limited lifespan so it is important to backup important data Do not write to a card if the battery power is low Low power could affect writing accuracy m Do not remove a card while read write is in progress 2 For more details on using memory cards see manuals accompanying the T cards About the write protect feature Memory media cards have a write protect function SD Card SD memory card SDHC memory card and SDXC memory card AN Set the write protect switch to the lock position if you do not want to record data Inserting memory media The following instructions apply to all types of supported media devices To insert memory media do the following 1 Turn the memory media so that the contacts metal areas face down 2 Insert the memory media into the memory media slot on the computer User s Manual 4 27 3 Press the memory media gently until it clicks into place Fi
60. arge under TOSHIBA group in the Apps view Move the slider to enable or disable the Sleep and Charge function m The Sleep and Charge function might not work with certain external devices even if they are compliant with the USB specification In those cases turn the power of the computer ON to charge the device m When Sleep and Charge function is enabled USB bus power DC5V is supplied to compatible ports even when the power of the computer is turned OFF USB bus power DC5V is similarly supplied to the external devices which are connected to the compatible ports However some external devices cannot be charged solely by supplying USB bus power DC5V As for the specifications of the external devices contact the device manufacturer or check the specifications of the external devices thoroughly before use m Using the sleep and charge function to charge external devices takes longer than charging the devices with their own chargers E f Sleep and Charge function is enabled the computer s battery discharges during hibernation or when the computer is turned off It is recommended that you connect the AC adaptor to the computer while using Sleep and Charge function User s Manual m External devices connected to the USB bus power DC5V function that interfaces with the power ON OFF of the computer might always be in an operational state E When there is a current overflow of the external devices connected to the compatible por
61. arranty in any way TOSHIBA standard limited warranty terms and limitations apply Starting the TOSHIBA PC Health Monitor User s Manual The TOSHIBA PC Health Monitor can be opened by clicking PC Health Monitor under TOSHIBA group in the Apps view The TOSHIBA PC Health Monitor main screen is displayed This utility might be disabled by default on your computer You can enable it by clicking Please click here to enable TOSHIBA PC Health Monitor The PC Health Monitor Software Notice amp Acceptance screen is displayed Carefully read the information displayed Selecting ACCEPT and clicking OK enables the program By enabling the TOSHIBA PC Health Monitor software you agree with these terms and conditions and to the use and sharing of the collected information Once the program is enabled the TOSHIBA PC Health Monitor screen is displayed and the program begins monitoring system functions and collecting information i A message is displayed if any changes which might interfere with the operation of the program are detected Follow the instructions displayed on screen in the message System Recovery There is a hidden partition allocated on the Hard Disk Drive for the System Recovery Options in the event of a problem You can also create recovery media and restore the system The following items are described in this section Creating Recovery Media Restoring the pre installed software from your created Recovery Media Res
62. ate of initial system use and also computer and device usage that is power settings battery temperature and recharging for models with battery CPU memory backlight illumination time and temperatures for various devices The collected information is not limited to the examples specified here The stored data uses a very small portion of the total hard disk capacity approximately 10 MB or less per year This information is used to identify and provide a notification of system conditions which might affect the performance of your TOSHIBA computer It might also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA authorized service providers Additionally TOSHIBA might also use this information for quality assurance analysis Subject to the use restrictions above the data on the internal storage drive logged might be transferred to entities located outside of your country or region of residence for example European Union Those countries might or might not have the same data protection laws or data protection levels as required by your home country or region You can disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel Doing so will automatically delete all collected information from the internal storage drive The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA obligations under its standard limited w
63. be observed to further reduce the risk of personal injury or damage to the computer Be certain to read the following general precautions and to note the cautions included in the text of the manual Provide adequate ventilation Always make sure that your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet even if your computer is in Sleep Mode In this condition observe the following m Never cover your computer or AC adaptor with any object m Never place your computer or AC adaptor near a heat source such as an electric blanket or heater m Never cover or block the air vents including those at the base of the computer m Always operate your computer on a hard flat surface Using your computer on a carpet or other soft material can block the vents m Always provide sufficient space around the computer Overheating your computer or AC adaptor could cause system failure computer or AC adaptor damage or a fire possibly resulting in serious injury Creating a computer friendly environment User s Manual Place the computer on a flat surface that is large enough for the computer and any other items you are using such as a printer Leave enough space around the computer and other equipment to provide adequate ventilation Otherwise they might overheat To keep your computer in prime operating condition prote
64. board of airplanes or E In any other environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment for example airports you are encouraged to ask for authorization to use the Wireless device prior to turning on the equipment Wireless LAN Technology A User s Manual The wireless communication function of the computer supports some wireless communication devices Only some models are equipped with both Wireless LAN and Bluetooth functions B Do not use the Wireless LAN Wi Fi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields Interference from a microwave oven or other source can disrupt Wi Fi or Bluetooth operation User s Manual m Turn off all wireless functionalities when near a person who might have a cardiac pacemaker implant or other medical electric device Radio waves might affect pacemaker or medical device operation possibly resulting in serious injury Follow the instruction for your medical device when using any wireless functionality E Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors Radio waves can cause malfunction of such equipment possibly resulting in serious injury m It migh
65. cessary lowering the processor speed or by lowering the processor speed first then if necessary turning on the fan Both of these functions are controlled through the Power Options When the processor s temperature falls within normal range the fan and the processor operation returns to its standard speed If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory will be lost TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security User and Supervisor User s Manual 5 6 i Passwords set by the TOSHIBA Password Utility function are different from the Windows password User Password T i User s Manual To start the utility click the following items under TOSHIBA group in the Apps view Password Utility gt User Password User authentication might be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords and so on Set button Click this button to register a password After a password is set you are prompted to enter it when you start the computer After you set the password a dialog box appears asking whether you want to save it to other media If you forget the password you can open the password file on another computer Be sure to keep the media in a safe place When entering the cha
66. cing heard feedback from either the internal microphone or an external microphone connected to the computer Refer to Sound System and Video mode for further information Volume cannot be adjusted during Windows start up or shut down If you are still unable to resolve the problem contact TOSHIBA Support External monitor Also refer to Operating Basics and to the documentation supplied with your monitor for further information User s Manual 6 13 LAN User s Manual Problem Monitor does not turn on No display Display error occurs Problem Cannot access LAN Procedure After confirming that the monitor s power switch is on you should check the connections to make sure that the power cord adaptor is firmly connected to the monitor and to a working power outlet Try adjusting the contrast and brightness controls on the external monitor Press the function key in order to change the display priority and ensure that it is not set for the internal display only Check to see if the external monitor is connected When the external monitor is set as the primary display device in extended desktop mode it does not display when the computer wakes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode To keep this from happening do not disconnect the external monitor while the computer is in Sleep or Hibernation Mode Remember to turn off the computer before disconnecting t
67. consider the simplest solution first The items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem m Make sure that you turn on all peripheral devices before you turn on the computer this includes your printer and any other external device you are using H Before you attach an external device you should first turn off the computer then when you turn the computer back on it recognizes the new device m Make sure that all optional accessories are configured properly in the computer s setup program and that all required driver software has been loaded refer to the documentation included with the optional accessories for further information on its installation and configuration Check all cables to ensure that they are correctly and firmly attached to the computer loose cables can cause signal errors Inspect all connecting cables for loose wires and all connectors for loose pins Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them ina permanent error log this helps you to describe your problems to TOSHIBA Support In addition if a problem recurs the log you have made helps to identify the problem faster Analyzing the problem User s Manual Sometimes the computer gives you clues that can help you identify why it is malfunctioning In view of this keep the following questions in mind Which part of the computer i
68. ct your work area from Dust moisture and direct sunlight H Equipment that generates a strong electromagnetic field such as stereo speakers other than speakers that are connected to the computer or speakerphones Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters E Extreme heat cold or humidity H Liquids and corrosive chemicals Stress injury Carefully read the nstruction Manual for Safety and Comfort It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use It also includes information on work space design posture and lighting that can help reduce physical stress Heat injury Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can become very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time for example if you rest the computer on your lap or if you keep your hands on the palm rest your skin might suffer a low heat injury If the computer has been used for a long time avoid direct contact with the metal plate supporting the various interface ports as this can become hot The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction If you need to transport the AC adaptor disconnect it and let it
69. cts thus the FreeType font engine the test programs documentation and makefiles at the very least This license was inspired by the BSD Artistic and IJG Independent JPEG Group licenses which all encourage inclusion and use of free software in commercial and freeware products alike As a consequence its main points are that E We dont promise that this software works However we will be interested in any kind of bug reports as is distribution m You can use this software for whatever you want in parts or full form without having to pay us royalty free usage m You may not pretend that you wrote this software If you use it or only parts of it in a program you must acknowledge somewhere in your documentation that you have used the FreeType code credits We specifically permit and encourage the inclusion of this software with or without modifications in commercial products We disclaim all warranties covering The FreeType Project and assume no liability related to The FreeType Project Finally many people asked us for a preferred form for a credit disclaimer to use in compliance with this license We thus encourage you to use the following text Portions of this software are copyright C lt year gt The FreeType Project www freetype org All rights reserved Please replace lt year gt with the value from the FreeType version you actually use Legal Terms Throughout this license the terms
70. d Canadian regulatory information Canada only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications Note that Canadian Department of Communications DOC regulations provide that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la class B respecte toutes les exgences du R glement sur le mat riel brouileur du Canada Following information is only valid for EU member States Disposal of products products must be collected and disposed of separately from household waste Integrated batteries and accumulators can be disposed of with the product They will be separated at the recycling centres et The crossed out wheeled dust bin symbol indicates that jt The black bar indicates that the product was placed on the market after August 13 2005 By participating in the separate collection of products and batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your cou
71. d and Connectors ccccceeeeceseneeeseeeeeseeeensseeeeseeneeeeeens 7 3 Information for Wireless Devices cceeeeseseeeeeeeeeeseeeeeneneeeeeeeneeeeeees 7 4 Legal FOOtm te ii caiisstsssccce cece ceccche de siecacceasestceacecpaauesoccesscsenncesseenecueuedeess 7 14 VCCI Class B Information Japan Only 2 sseecceeeeeeeeeeeeeeeeeeees 7 17 OpenSSL Toolkit License Issues cccseseeeseeeenseeeeeeeeneeeeeeeeneneeeeees 7 17 FreeType License ISSUES ccceeeeeeeeeeeeeeeeeeee cee eeseeaeeeeeeseeeeeeeeeees 7 19 Index Chapter 1 TOSHIBA Legal Regulatory and Safety This chapter states the Legal regulatory and safety information applicable to TOSHIBA computers Copyright Disclaimer and Trademarks Copyright 2014 TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein First edition November 2014 Copyright authority for music movies computer programs databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner Copyrighted material can be reproduced only for personal use or use within the home Any other use beyond that stipulated above including conversion to digital format alteration transfer of copied material and distribution on a network
72. der to a higher level Audio Enhancements In order to apply the sound effects for your current speaker do the following 1 Right click on the Speakers icon on the Windows Taskbar and then select Playback devices from the sub menu 2 Select Speakers and click Properties 3 On the Enhancements tab select the sound effects you would like and click Apply DTS Sound DTS Sound utilizes advanced patented techniques to retrieve audio cues buried in the original source material and deliver immersive surround sound complete with deep rich bass and crystal clear dialog DTS Sound is provided with some models It provides the following features E Immersive surround sound with bass and dialog enhancement H Broad sweet spot with elevated sound image E Improved volume output delivering maximum volume without creating clipping or distortion mDialog enhancement for clear and intelligible vocals m Bass enhancement for rich low frequency production High frequency definition for crisp details To access the utility click DTS Sound under DTS Inc in the Apps view U S patents apply to this product See http patents dts com Manufactured under license from DTS Licensing Limited Video mode User s Manual Video mode settings are configured via the Screen Resolution dialog To open the Screen Resolution dialog click Control Panel gt Appearance and Personalization gt Display gt Change display settings under Win
73. down the computer in this way could allow the operating system to reactivate and run pre programmed tasks or preserve unsaved data which could interfere with aviation or other systems possibly causing serious injury User s Manual Before entering Sleep Mode be sure to save your data To prevent data loss do not switch to Sleep Mode while transferring data to external media such as USB devices memory media or other external memory devices Do not remove the battery pack while the computer is in Sleep Mode unless the computer is connected to an AC power source It can cause data loss in the memory When the AC adaptor is connected the computer will go into Sleep Mode according to the settings in the Power Options to access it click Control Panel gt System and Security gt Power Options under Windows System in the Apps view To restore the operation of the computer from Sleep Mode press and hold the power button or any key on the keyboard for a short amount of time Note that keyboard keys can only be used if the Wake up on Keyboard option is enabled within the TOSHIBA System Settings If the computer enters Sleep Mode while a network application is active the application might not be restored when the computer is next turned on and the system returns from Sleep Mode To prevent the computer from automatically entering Sleep Mode disable Sleep Mode within the Power Options To use the Hybrid Sleep function configur
74. dows System in the Apps view 4 34 l If you are running some applications for example a 3D application or video J playback you might see some disturbance flickering or frame dropping on your screen If that occurs adjust the resolution of display lowering it until the screen is displayed properly User s Manual 4 35 Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer and the advanced usage of some utilities Utilities and Applications This section describes the pre installed utilities that come with the computer and details how to start them For further information on their operation refer to online manual help files or README TXT file if User s Manual applicable of each utility TOSHIBA Display Utility TOSHIBA Password Utility TOSHIBA Display Utility includes Desktop Text Size utility Split Screen utility or Resolution settings Desktop Text Size allows you to make the text size bigger or smaller on the desktop according to your usage and favorite You can change the text size on the display and on the title bar of windows by changing the scaling of the text size When the scaling is smaller more information appears on the display simultaneously but the text size becomes smaller When the scaling is larger less information appears on the display simultaneously but the text size becomes larger You can install Split Screen utility by you
75. e it in the Power Options Benefits of Sleep Mode The Sleep Mode feature provides the following benefits Restores the previous working environment more rapidly than the Hibernation Mode feature Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature Allows the use of the panel power off feature Executing Sleep Mode You can enter Sleep Mode in one of following ways Click the power icon cy on the Start screen and then select Sleep In the Settings charm click Power and then select Sleep Close the display panel Note that this feature must be enabled within the Power Options Press the power button Note that this feature must be enabled within the Power Options When you turn the power back on you can continue where you left off when you shut down the computer When the computer is in Sleep Mode the Power indicator blinks white If you are operating the computer on battery power you can lengthen the overall operating time by turning it off into Hibernation Mode Sleep Mode consumes more power while the computer is off Sleep Mode limitations Sleep Mode will not function under the following conditions Power is turned back on immediately after shutting down Memory circuits are exposed to static electricity or electrical noise Hibernation Mode A User s Manual The Hibernation Mode feature saves the contents
76. e items that are available from your reseller or TOSHIBA dealer Universal AC Adaptor If you frequently use your computer at more than one site it might be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to carry the adaptor with you always Battery pack An additional battery pack can be purchased for use as either a spare or replacement Refer to the Battery section for further information Sound System and Video mode This section describes some of the audio control functions Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows H To launch the Volume Mixer utility right click on the speaker icon on the Windows Taskbar and then select Open Volume Mixer from the sub menu H To adjust the volume level of speakers or headphones move the Speakers slider H To adjust the volume level of an application that you are using move the slider for the corresponding application User s Manual 4 33 Microphone Level To change the microphone recording level do the following 1 Right click on the speaker icon on the Windows Taskbar and select Recording devices from the sub menu 2 Select Microphone and click Properties 3 On the Levels tab move the Microphone slider to increase or decrease the microphone volume level If you feel the microphone volume level is inadequate move the Microphone Boost sli
77. e problem and suspect that it is hardware related read the enclosed warranty booklet or visit the TOSHIBA technical support website http pc support toshiba eu Chapter 7 Appendix Specifications This section summarizes the technical specifications of the computer Physical Dimensions The following physical dimensions do not include parts that extend beyond the main body The physical dimensions might vary depending on the model you purchased Size m Approximately 413 w x 268 d x 29 33 7 h millimeters m Approximately 413 w x 268 d x 28 4 33 1 h millimeters E Approximately 413 w x 268 d x 31 2 35 9 h millimeters not including parts that extend beyond the main body Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 20 to 80 95 F noncondensing Non operating 20 C 4 F to 60 C 10 to 90 140 F noncondensing Wet bulb temperature 29 C maximum Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum User s Manual 7 1 Power Requirements AC adaptor 100 240V AC 50 Hz or 60 Hz cycles per second Computer 19V DC External RGB monitor port pin assignment o 6 Pin Signal Name Description 1 0 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 5V Power Sup
78. ed features for sleep mode hibernate mode and shutdown state H Display Allows you to select the internal LCD and or external monitor when the computer boots up H Boot Options Allows you to change the sequence in which your computer searches the drives for the operating system E Keyboard Allows you to access the wake on keyboard function or to configure the function keys mg USB Allows you to set conditions for USB gH SATA Allows you to set conditions for SATA T m LAN Allows you to set conditions for LAN The settings or options explained here might vary depending on the model you purchased After you changed the settings a dialog box might appear to prompt you that the changes will take effect after the computer is restarted Make sure to restart your computer immediately to apply these changes USB Charge Your computer can supply USB Bus power DC5V to the USB port The port with the icon 4 supports the following feature m USB Sleep and Charge E System ON CDP Charge USB Sleep and Charge User s Manual You can use the Sleep and Charge function to charge certain USB compatible external devices such as mobile phones or portable digital music players Your computer can supply USB bus power DC5V to the compatible port even when the computer is turned OFF Power OFF includes Sleep Mode Hibernation Mode or shutdown state To set USB Sleep and Charge feature click System Settings gt Sleep and Ch
79. en select the Enable Vari Bright check box If you want to improve the picture quality under the conditions mentioned above adjust the setting towards Maximize Quality or disable this feature Power Condition Descriptions Power conditions i The computer operating capability and battery charge status are affected by different power conditions including whether an AC adaptor is connected and what the charge level is for that battery The LED in the following table refers to the DC IN Battery indicator AC adaptor connected AC adaptor not connected Battery fully charged Battery partially charged or no charge Remaining battery capacity is above low battery trigger point Remaining battery capacity is below low battery trigger point Remaining battery capacity is exhausted DC IN Battery indicator Check the DC IN Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected The following indicator conditions should be noted User s Manual Flashing amber Amber Power on Power off no operation Operates e No charge e No charge e LED white e LED white e Operates Quick charge e Charge e LED amber e LED amber e Operates e LED off e Operates LED flashes amber Computer shuts down The battery charge is low The AC adaptor must be connected to recharge the battery Indicates that the AC adaptor is connected and the
80. environmental temperature operating time decreases at low temperatures 4 21 m Whether you enable Sleep and Charge function Batteries exhausted time When you turn off the power of your computer with batteries fully charged the batteries exhaust within the following approximate period Battery type Sleep Mode Shut Down Mode Battery pack 24Wh 3 about 2 days about 22 days cell Battery pack 48Wh 6 about 4 days about 43 days cell Battery pack 66Wh 6 about 5 5 days about 60 days cell high capacity Extending battery life To maximize the life of your battery packs do the following at least once a month 1 Turn off the computer s power 2 Disconnect the AC adaptor and turn on the computer s power If it does not turn on then go to Step 4 3 Operate the computer on battery power for five minutes If you find that the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharge However if the DC IN Battery indicator flashes or there is some other warning to indicate a low battery condition go to Step 4 4 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power The DC IN Battery indicator glows amber to indicate that the battery pack is being charged However if DC IN Battery indicator does not glow this indicates that power is not being supplied Check the connections for the AC adaptor and the pow
81. ep Mode setting 2 9 System automatic 5 5 Sound system Index 2 problems 6 13 U USB device problems 6 11 V Video mode 4 34 Video RAM 3 10 W Web Camera 3 7 Wireless communication 7 5 User s Manual Index 3
82. er cord 5 Charge the battery pack until the DC IN Battery indicator glows white Replacing the battery pack Be aware that the battery pack is classified as a consumable item The operating life of the battery pack will gradually reduce through repeated charging and discharging and should be replaced when it reaches the end of its operating life In addition to this you might also replace a discharged battery pack with a charged spare when you are User s Manual 4 22 operating your computer away from an AC power source for an extended period of time This section explains how to remove and install the battery pack and begins with the removal process which is detailed through the following steps AN E Do not remove the battery pack while the computer is in Sleep Mode as data is stored in RAM so if the computer loses power it could be lost In Hibernation Mode data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries Removing the battery pack To remove a discharged battery do the following 1 Save your work 2 Click the power icon cy on the Start screen and then click Shut down while holding down the SHIFT key Ensure that the Power indicator is off 3 Remove all cables a
83. erfere with one another If you use Bluetooth and Wireless LAN devices simultaneously you might occasionally experience a less than optimal network performance or even lose your network connection If you experience any such problem immediately turn off either one of your Bluetooth or Wireless LAN If you have any questions about using Wireless LAN or Bluetooth Module visit http www pc support global toshiba com In Europe visit http www toshiba europe com computers tnt bluetooth htm Wireless Devices and your health Wireless products like other radio devices emit radio frequency electromagnetic energy The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones Because Wireless products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes Wireless products are safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of Wireless products might be restricted by the proprietor of the building or responsible representatives of the organization These situations might for example include m Using the Wireless products equipment on
84. ety of easy to view angles Press this button to power on off the computer The Power indicator glows white when the computer is turned on However if you turn the computer off into Sleep Mode this indicator will blink white The keyboard contains character keys control keys function keys and special Windows keys providing all the functionality of a full size keyboard Refer to the The Keyboard section for details The Touch Pad located in the palm rest is used to control the movement of the on screen pointer To use the Touch Pad simply touch and move your fingertip across it in the direction you want the on screen pointer to go Touch Pad appearance depends on the model you purchased User s Manual Touch Pad control buttons The two buttons located on the bottom of the Touch Pad are used like the buttons on a standard mouse Press the left button to select a menu item or to manipulate text or graphics designated by the pointer and press the right button to display a menu or other function depending on the software you are using Touch Pad control buttons appearance depends on the model you purchased Internal Hardware Components This section describes the internal hardware components of your computer The actual specifications might vary depending on the model you i A User s Manual purchased CPU Legal Footnote CPU The processor type varies depending on model To check which type of proces
85. ff 1 Low battery automatic Hibernation Mode This feature automatically cuts off power to the computer s display panel when there is no keyboard input for a specified time with power being restored the next time a key is pressed This can be specified in the Power Options This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time with power being restored when the hard disk drive is next accessed This can be specified in the Power Options This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time This can be specified in the Power Options Two levels of password security supervisor and user are available to prevent unauthorized access to your computer A microprocessor in the computer s intelligent power supply detects the battery s charge automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor This can be specified in the Power Options This feature lets you configure the computer in order to save battery power This can be specified in the Power Options This feature automatically turns power to the computer off when the display panel is closed and turns it back on when the display panel is opened This can be specified in the Power Options When battery
86. g figure shows the left side of the computer Figure 3 2 The left side of the computer E t 1 Security lock slot 4 Universal Serial Bus USB 2 0 port 2 DC IN 19V jack 5 Optical disc drive 3 Universal Serial Bus USB 2 0 port Provided with some models Product appearance depends on the model you purchased Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer D DC IN 19V jack The AC adaptor connects to this jack in order to sd power the computer and charge its internal batteries Note that you must only use the model of AC adaptor supplied with the computer at the time of purchase Using the wrong AC adaptor can damage the computer User s Manual 3 2 T Universal Serial Bus One or two Universal Serial Bus ports which USB 2 0 ports comply to the USB 2 0 standard are provided on the left side of the computer The USB 2 0 port is not compatible with USB 3 0 devices Bm Note that it is not possible to confirm the operation of all functions of all USB devices that are available Some functions associated with a specific device might not operate properly E Before removing a USB device from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove Keep
87. g on the country and region where you purchased REACH Compliance Statement User s Manual The European Union EU chemical regulation REACH Registration Evaluation Authorization and Restriction of Chemicals entered into force on 1 June 2007 with phased deadlines to 2018 Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation Please consult the following website www toshiba eu reach for information about the presence in our articles of substances included on the candidate list according to REACH ina concentration above 0 1 weight by weight Following information is only for Turkey H Disposal of products The crossed wheelie bin symbol means that this ps product should not be collected and disposed with other household wastes When product become waste at the end of life to protect environment and human health it should be given to nearest collection recycling or disposal center For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchased E Toshiba meets all requirements of Turkish regulation 28300 Restriction of the use of certain hazardous substances in electrical and electronic equipment AEEE Y netmeli ine Uygundur Toshiba 28300 say l T
88. ge PC settings Click Update and recovery under PC settings and then click Recovery Click Get started under Remove everything and reinstall Windows Follow the on screen instructions to finish the recovery Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability however should problems occur you are able to use the procedures detailed in this chapter to help determine the cause You should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place Problem solving process If you observe the following guidelines resolving problems will be much easier H Stop immediately when you recognize a problem exists as taking further action might result in data loss or damage or you might destroy valuable problem related information that can help solve the problem m Observe what is happening Write down what the system is doing and what actions you performed immediately before the problem occurred Make a screenshot of the current display Also be aware that the questions and procedures described in this chapter are meant only as a guide they are not definitive problem solving techniques In reality many problems can be solved simply but a few may require help from TOSHIBA Support If you find you need to consult others be prepared to describe the problem in as much detail as possible Preliminary checklist User s Manual You should always
89. ge appears in the screen Enter Password At this point the function keys do not work They will function after you enter the password 2 Enter the Password 3 Press ENTER If you enter the password incorrectly three times in a row or if you do not enter the password within 1 minute the computer shuts off In this case some features that can power on the computer automatically Wake up on LAN Task Scheduler etc might not work You must turn the computer back on to retry password entry TOSHIBA System Settings i User s Manual TOSHIBA System Settings is the TOSHIBA configuration management tool available through the Windows operating system To run TOSHIBA System Settings click System Settings under TOSHIBA group in the Apps view The TOSHIBA System Settings window contains a number of tabs to allow specific functions of the computer to be configured In addition there are also three buttons OK Cancel and Apply OK Accepts your changes and closes the TOSHIBA System Settings window Cancel Closes the window without accepting your changes Apply Accepts all your changes without closing the TOSHIBA System Settings window Some options shown in gray are possible to confirm their status TOSHIBA System Settings screen might have the following tabs m General Allows you to view the current BIOS version or change certain settings back to their default values H Sleep and Charge Allows you to set advanc
90. gram recording errors Please view video during times when there is no recording prescheduled The resume function cannot be used with some discs on the CyberLink PowerDVD for TOSHIBA It is recommended the AC adaptor be connected when playing video Power saving features may interfere with smooth playback When playing video using battery power set the Power Options to Balance The screen saver is disabled during video playback using the CyberLink PowerDVD for TOSHIBA The computer will not automatically go into Hibernation or Sleep mode Do not configure the Display automatic power off function to run while the CyberLink PowerDVD for TOSHIBA is running Do not switch to Hibernation or Sleep Mode when running the CyberLink PowerDVD for TOSHIBA Do not lock the computer using the Windows logo H L keys when running the CyberLink PowerDVD for TOSHIBA The CyberLink PowerDVD for TOSHIBA does not have a parental control function Carry out the installation uninstallation of the CyberLink PowerDVD for TOSHIBA under a user account with administrator rights Do not change Windows Users while CyberLink PowerDVD for TOSHIBA is running For some DVD or video files using the control window to change the audio track will also change the subtitle track The playback of some media files may not be normal by this player This may also happen when using Windows Media Player and Video app Display Devices amp Audio User s Manual If the
91. gure 4 8 Inserting memory media 1 Memory media slot 2 Memory media Product appearance depends on the model you purchased Make sure the memory media is oriented properly before you insert it If you insert the media in wrong direction you might not be able to remove it When inserting the memory media do not touch the metal contacts You could expose the storage area to static electricity which can destroy data Do not turn off the computer or switch to Sleep Mode or Hibernation Mode while files are being copied Failure to do so might cause data loss Removing memory media The following instructions apply to all types of supported media devices To remove memory media do the following 1 E AVN Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar Select memory media Push the memory media until you hear a click to partially release it Grasp the media and pull it out of the slot If you remove the memory media or turn off the power while the computer is accessing the memory media you might lose data or damage the media Do not remove the memory media while the computer is in Sleep or Hibernation Mode The computer could become unstable or data in the memory media could be lost Do not remove only the miniSD microSD Card while leaving the adaptor in the memory media slot External Display Your computer video capabilities can be enhanced with additional displays User s Manual
92. hanisms ensure a high level of security H Authentication prevents access to critical data and makes it impossible to falsify the origin of a message m Encryption prevents eavesdropping and maintains link privacy Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2 4 GHz band which is license free and compatible with radio systems in most countries in the world Radio Regulatory Information User s Manual Radio links You can easily establish links between two or more devices with these links being maintained even if the devices are not within a line of sight of each other The Wireless device must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product This product complies with the following radio frequency and safety standards Europe Restrictions for Use of 2400 0 2483 5MHz Frequencies in Europe France Italy Luxembourg Norway Russian Federation Outdoor use limited to 10mW e i r p within the band 2454 2483 5MHz Implemented Implemented Military Radiolocation use Refarming of the 2 4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 For private use a general authorization is required if WAS RLAN s are used outside own premises For public use a general authorization is required General authoriza
93. he external monitor When the display panel and an external monitor are set to clone mode and they are turned off by the timer the display panel or the external monitor might not display when turned on again If this occurs press the function key to reset the display panel and external monitor to clone mode Check that the cable connecting the external monitor to the computer is firmly attached If you are still unable to resolve the problem contact TOSHIBA Support Procedure Check for a firm cable connection between the LAN jack and the LAN hub Problem Wake up on LAN does not work Wireless LAN Problem Cannot access Wireless LAN Bluetooth Problem Cannot access Bluetooth device User s Manual Procedure Make sure the AC adaptor is connected The Wake up on LAN function consumes power even when the system is off Check to make sure fast startup is disabled 1 Click Control Panel gt System and Security gt Power Options under Windows System in the Apps view 2 Click Choose what the power button does or Choose what closing the lid does 3 Click Change settings that are currently unavailable 4 Clear the Turn on fast startup check box 5 Click the Save changes button If problems persist consult your LAN administrator Procedure Make sure that the wireless communication function of the computer is on If problems persist contact your LAN administrator Procedure Check t
94. he recovery partition If you have not created Recovery Media contact TOSHIBA support for assistance Restoring the pre installed software from the Recovery Hard Disk Drive T User s Manual A portion of the total Hard Disk Drive space is configured as a hidden recovery partition This partition stores files which can be used to restore pre installed software in the event of a problem If you set up your Hard Disk Drive again later do not change delete or add partitions in a manner other than specified in the manual otherwise you might find that space for the required software is not available In addition if you use a third party partitioning program to reconfigure the partitions on your Hard Disk Drive you might find that it becomes impossible to set up your computer Make sure that the AC adaptor is connected during the restoring process When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost 1 Click the power icon Q on the Start screen and then select Restart 2 Hold down 0 zero key and then release this key one second after the computer is power on Choose Yes if you want to continue 3 Select Troubleshoot User s Manual 4 5 Select Reset your PC Follow the on screen instructions to finish the recovery You can also perform the restoration through PC settings in the operating system 1 2 3 Click the Settings charm and click Chan
95. hen operating in AC power mode and might decrease considerably when operating in battery power mode Total Available Graphics Memory is the total of as applicable Dedicated Video Memory System Video Memory and Shared System Memory Shared System Memory varies depending on system memory size and other factors Wireless LAN User s Manual The transmission speed over the wireless LAN and the distance over which wireless LAN can reach might vary depending on surrounding electromagnetic environment obstacles access point design and configuration and client design and software hardware configurations The actual transmission speed is lower than the theoretical maximum speed Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media VCCI Class B Information Japan Only CORES JIABSRMRHEE CT COREL RERA CE AT ScLERMELTHET AM CORED OFLE VAL SMEMIIRL CRASH SL PEM BSS SRCT CLABES MIRRA EIRO TEL RUIRUEL TEAL VCCI B OpenSSL Toolkit License Issues User s Manual LICENSE ISSUES The OpenSSL toolkit stays under a dual license i e both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit See below for the actual license texts Actually both licenses are BSD style Open Source licenses In case of any license issues related to OpenSSL please contact openssl core openssl org OpenSSL License Copyright c
96. hen release this key one second after the computer is power on The BIOS setup utility will load 3 Set the date in the System Date field 4 Set the time in the System Time field 5 Press F10 a confirmation message will be displayed 6 Select Yes the BIOS setup utility will end and the computer will restart Keyboard problems can be caused by the setup and configuration of the computer Refer to the The Keyboard section for further information Problem Output to screen is garbled Procedure Refer to your software documentation to ensure that it is not remapping the keyboard in any way remapping involves changing or reassigning the function of each key If you are still unable to use the keyboard you should contact TOSHIBA Support Internal display panel User s Manual Apparent problems of the computer s display panel might be related to setup and configuration of the computer Problem No display Procedure Press the function keys to adjust the display priority and to make sure that it is not set for output to an external monitor Problem Markings appear on the computer s display panel Hard Disk Drive Problem Computer does not boot from Hard Disk Drive Slow performance Optical Disc Drive Procedure These marks might have come from contact with the keyboard and Touch Pad while the display panel has been closed Try to remove the marks by gently wiping the display panel with
97. his product was designed to fulfil the EMC Electromagnetic Compatibility requirements to be observed for so called Residential commercial and light industry environments TOSHIBA do not approve the use of this product in working environments other than the above mentioned Residential commercial and light industry environments For example the following environments are not approved E Industrial Environments e g environments where a mains voltage of 380 V three phase is used mH Medical Environments E Automotive Environments E Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA The consequences of the use of this product in non approved working environments may be Interference with other devices or machines in the near surrounding area Malfunction of or data loss from this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non approved working environments before use In the case of automobiles or aircraft the manufacturer or airline respectively should be asked for permission before use of this product Furthermore for general safety reasons the use of this product in environments with explosive atmospheres is not permitte
98. isables the Touch Pad F6 FN F6 Moves media backward F7 FN F7 Plays or pauses media playback F8 FN F8 Moves media forward F9 FN F9 Decreases the computer s volume F10 FN F10 Increases the computer s volume F11 FN F11 Turns the sound on or off F12 FN F12 Turns the Airplane mode on or off FN 1 FN 1 Reduces the icon size on the desktop or the font sizes within one of the supported application windows FN 2 FN 2 Enlarges the icon size on the desktop or the font sizes within one of the supported application windows FN Space FN Space Changes the display resolution FN Gx FN f Turns the keyboard backlight on or off This function is supported with some models Some functions show the toast notification at the edges of the screen Those toast notifications are disabled at factory default You can enable them in the TOSHIBA Function Key application To access it click Function Key under TOSHIBA group in the Apps view Windows special keys The keyboard provides two keys that have special functions in Windows the Windows logo key activates the Start screen while the application key has the same function as the secondary right mouse button This key activates the Windows Start screen This key has the same function as the secondary right mouse button Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation but you are able to gene
99. key integrated into this product is required for uninterrupted enjoyment of Blu ray Disc An Internet connection is required for renewal AACS key renewal is provided free of charge for 5 years after the purchase of this product however renewal beyond 5 years is subject to conditions specified by the software provider TOSHIBA Corporation Do not play back video while recording television programs using other applications Failure to do so might cause video playback or television program recording errors In addition if pre scheduled recording starts during video playback it might cause video playback or television program recording errors Please view video during times when there is no recording prescheduled While playing a BD J title keyboard shortcut is ineffective Resume play function cannot be used with some discs on TOSHIBA Blu ray Disc Player The interactive function on Blu ray discs might not work depending on the contents or network situation Blu ray drives and their associated media are manufactured according to the specifications of three marketing regions Region codes can be set from TOSHIBA Blu ray Disc Player Click the Settings button in the Control Panel And click the Blu ray Region Setting Tab When you purchase Blu ray Video make sure it matches your drive otherwise it will not play properly To play back video on an external display or TV using TOSHIBA Blu ray Disc Player use output devices like exte
100. ll stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m To remain in conformance with European spectrum usage laws for Wireless LAN operation the above 2 4GHz and 5GHz channel limitations apply for outdoor usage The user should use the wireless LAN utility to User s Manual User s Manual check the current channel of operation If operation is occurring outside of the allowable frequencies for outdoor use as listed above the user must contact the applicable national spectrum regulator to request a license for outdoor operation Canada Industry Canada IC This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage regu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable Les dispositifs fonctionnant dans la bande 5 15 5 25GHz sont r serv s uniquement pour une utilisation a l int rieur
101. ly before use Always use the USB cable that was included with your USB device Function under Battery Mode This option can be used to enable disable sleep and charge under battery mode It also displays the remaining battery capacity Move the slider to enable or disable this function Enabled Enables Sleep and Charge function under battery mode Disabled Enables Sleep and Charge function only when the AC adaptor is connected Disable features when Specifies the lower limit of remaining battery life the battery level by moving the slider bar If the remaining battery reaches life falls below the setting the Sleep and Charge function is stopped This setting is only available when the Function under Battery Mode is enabled System ON CDP Charge i This function enable disable CDP Charging Downstream Port to use rapid USB charge while the computer is powered on When System ON CDP Charge Mode is enabled your computer can supply USB bus power DC5V 1 5A to the compatible ports while the computer is turned on To set System ON CDP Charge Mode click System Settings gt USB under TOSHIBA group in the Apps view Enabled Rapid USB battery charge at maximum 1 5A while PC is powered On Disabled Conventional USB battery charge while PC is powered On The System ON CDP Charge Mode might not work with certain external devices even if they are compliant with the USB specifications In those cases use a USB port witho
102. me of the disc media might not be compatible with the optical disc drive connected to your computer You should therefore verify that the optical disc drive supports the blank media you have chosen before proceeding m USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding 2 Turn on your computer and allow it to load the Windows operating system from the Hard Disk Drive as normal 3 Insert the first blank disc into the optical disc drive tray or insert the USB Flash Memory into one available USB port 4 Click Recovery Media Creator under TOSHIBA group in the Apps view 5 After Recovery Media Creator starts select the type of media and the title you wish to copy and then click the Create button Restoring the pre installed software from your created Recovery Media A User s Manual If the pre installed files are damaged you are able to use the Recovery Media you have created to restore the computer to the state it was in when you originally received it To perform this restoration do the following m When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost m Please make sure to use the default Boot Mode option in the BIOS setup utility before restoring 1 Click the power icon l on the Start screen and then select Restart 2 Hold down the F2 key and then release this key one second after the computer is power on
103. mined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected H Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits might be attached to this equipment Operation with non compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s external RGB monitor port Universal Serial Bus USB 2 0 and 3 0 ports HDMI port and Headphone Microphone combo jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 9
104. n to your computer you can also download many other applications at the click of your mouse In the Windows Store you can search for and browse thousands of apps all grouped into easy to find categories Sign in options Windows offers a number of sign in options including Password kD PIN E and Picture password E authentication to prevent from unauthorized access If you have multiple sign in methods set for a user account you can select an option on the Windows login screen by clicking sign in options Password authentication is the default sign in option Turning off the power The power can be turned off in one of the following modes either Shut Down Mode Sleep Mode or Hibernation Mode Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the main screen of the operating system the next time it is turned on 1 Ifyou have entered data either save it to the Hard Disk Drive or to other storage media User s Manual 2 8 A 2 Make sure all disk disc activity has stopped before removing the disk disc m f you turn off the power while a disk disc is being accessed you might lose data or damage the disk m Never turn off the power while an application is running Failure to do so can cause data loss m Never turn off the power disconnect an external storage device or remove storage media during data read write Failure to do so can cause data
105. nd peripherals that are connected to the computer 4 Close the display panel and turn the computer upside down 5 Slide the battery lock into its unlocked position 6 Slide and hold the battery release latch to disengage the battery pack and then lift it up to remove it from the computer Figure 4 5 Releasing the battery pack 1 Battery lock 3 Battery pack 2 Battery release latch Installing the battery pack To install a battery pack do the following User s Manual 4 23 LAN i LAN Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries Insert the battery pack as far as it will go into the computer 2 Ensure that the battery pack is securely in place and the battery lock is in its locked position 3 Turn your computer over The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T This section describes how to connect disconnect to a LAN m The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature m The Link speed 10 100 1000 megabits per second changes automatically depending on the network conditions connected device cable or noise and so on c
106. ntry please visit our website www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product User s Manual 1 5 A Disposal of batteries and or accumulators The crossed out wheeled dust bin symbol indicates that batteries and or accumulators must be collected and disposed of separately from household waste PD MEGA If the battery or accumulator contains more than the specified values of lead Pb mercury Hg and or cadmium Cd defined in the European Battery Directive then the chemical symbols for lead Pb mercury Hg and or cadmium Cd will appear below the crossed out wheeled dust bin symbol By participating in the separate collection of batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health To achieve this you should take any battery and or accumulator to your local recycling site or to a retail outlet or facility that offers to collect these devices for environmentally friendly disposal ensuring that the terminal contacts are covered by non conductive tape For more detailed information about the collection and recycling programmes available in your country please visit our website www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product These symbols might not stick dependin
107. o a live electrical outlet It is possible that if data is written while powered by the battery pack the write process might sometimes fail due to low battery power In these instances data loss might occur Important message Before you write or rewrite to any of the media supported by the optical disc drive read and follow all of the setup and operating instructions in this section If you fail to do so you might find that the optical disc drive might not function properly and you might fail to write or rewrite information successfully This might cause you to either lose data or incur other damage to the drive or media Disclaimer TOSHIBA does not assume responsibility for the following m Damage to any disc that might be caused by writing or rewriting with this product m Any change or loss of the recorded contents of media that might be caused by writing or rewriting with this product or for any business profit loss or business interruption that might be caused by the change or loss of the recorded contents E Damage that might be caused by using third party equipment or software Given the technological limitations of current optical disc writing drives you might experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices In view of this it is good practice to make two or more copies of important data in case of any undesired change or loss of the recorded contents Before w
108. o ensure that the wireless communication function of the computer is on Check to ensure that the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on Check to ensure that no optional Bluetooth Adaptor is installed in the computer The built in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller If you are still unable to resolve the problem contact TOSHIBA Support TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer you might need to contact TOSHIBA for additional technical assistance Before you call Some problems you experience might be related to software or the operating system so it is important that you investigate other sources of assistance first Before contacting TOSHIBA try the following H Review troubleshooting sections in the documentation supplied with your software and or peripheral devices m If aproblem occurs when you are running software applications consult the software documentation for troubleshooting suggestions and consider calling the software company s technical support department for assistance m Consult the reseller or dealer from where you purchased your computer and or software they are your best resource for current information and support TOSHIBA technical support User s Manual If you are still unable to solve th
109. o the Legal Footnotes section Handle your computer carefully to avoid scratching or damaging the Surface Front with the display closed User s Manual The following figure shows the front of the computer with the display panel in the closed position Figure 3 1 Front of the computer with display panel closed T s gt w a 1 Memory media slot 3 Wireless communication indicator 2 DC IN Battery indicator Memory media slot This slot lets you insert an SD SDHC SDXC memory card minisD microSD Card and MultiMediaCard Refer to the Memory media section for more information Keep foreign metal objects such as screws staples and paper clips out of the Memory media slot Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury wi DC IN Battery The DC IN Battery indicator shows the condition indicator of the DC IN and the battery charge status White indicates that the battery is fully charged while the power is being correctly supplied from the AC power adaptor Refer to the Power Condition Descriptions section for more information on this feature yp Wireless The Wireless communication indicator glows communication amber when the Bluetooth or Wireless LAN indicator functions are turned on Only some models are equipped with Bluetooth and Wireless LAN functions Left side The followin
110. of memory to the Hard Disk Drive when the computer is turned off so that the next time it is turned on the previous state is restored Note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer Save your data While entering Hibernation Mode the computer saves the contents of memory to the Hard Disk Drive However for safety sake itis best to save your data manually Data will be lost if you disconnect the AC adaptor before the save is completed To prevent data loss do not switch to Hibernation Mode while transferring data to external media such as USB devices memory media or other external memory devices Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits Saves data to the Hard Disk Drive when the computer automatically shuts down because of a low battery condition You can return to your previous working environment immediately when you turn on the computer Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature Allows the use of the panel power off feature Starting Hibernation Mode To enter Hibernation Mode click the power icon Q on the Start screen and then select Hibernate 1 To show Hibernate in Power menu set up according to the following J steps 1 Click Control Panel gt System and Security gt Power Op
111. ointer moves too fast or too slow The on screen pointer moves erratically USB device In addition to the information in this section also refer to the documentation supplied with your USB device User s Manual Problem USB device does not work Procedure In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Control Panel gt Hardware and Sound gt Mouse under Windows System in the Apps view 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK The elements of the mouse responsible for detecting movement might be dirty Refer to the documentation supplied with the mouse for instructions on how to clean it If you are still unable to resolve the problem contact TOSHIBA Support Procedure Remove the USB device from the computer and then reconnect it to a free port in order to ensure that it is firmly attached Ensure that any required USB device drivers are properly installed To achieve this refer
112. on describes how to turn on the power The Power indicator indicates the status Refer to the Power Condition Descriptions section for more information a E After you turn on the power for the first time do not turn it off until you have set up the operating system E Volume cannot be adjusted during Windows Setup Open the display panel 2 Press the power button Figure 2 5 Turning on the power 1 Power button Product appearance depends on the model you purchased Initial setup The Windows Startup Screen is the first screen displayed when you turn on the power To install the operating system properly follow the on screen instructions on each screen User s Manual 2 6 T When it is displayed be sure to read the License Terms carefully Getting to know Windows For detailed information on what is new and how to operate Windows refer to the Windows Help and Support Start screen The Start screen is the launching pad for everything you can do in the Windows operating system providing new and easy ways to access everything from your favorite apps and websites to your contacts and other important information From the Start screen you can start typing to search for what you want From there you can easily switch between results for apps files and more Windows Taskbar Point to the bottom edge to show the Windows Taskbar on the Start screen If you ve moved the Windows Taskbar to another edge
113. ontent created by you in 3D The 3D playback of any video content not created by the user might require the direct or indirect permission of third parties where such content is protected by copyright unless otherwise permitted under applicable law The protection of intellectual property rights is essential for TOSHIBA In this respect TOSHIBA underlines that the Player should not be used in a manner infringing such rights It is your responsibility to ensure that you do not infringe any applicable intellectual property laws when you decide to use the Player and more specifically when you decide to activate the 2Dto3D conversion function of the Player Some functions cannot be used during 3D playback In such cases any buttons used for those functions may be disabled Depending on the system environment the player may automatically switch into 2D if you perform any of the following operations during 3D playback Furthermore you may experience some time lag when the switching occurs Opening windows or pop ups such as Right Click Menu Settings Window File Select or Error Message Using Windows features Using any other applications Make sure to use AC adapter when playing with 3D playback feature enabled Depending on the system environment 3D playback may only be used when the Video Display Window is at full screen 3D playback might not function when windowed In order for the 3D playback to work on an external
114. other computer or other device and you cannot reproduce any copyrighted material except for your personal enjoyment The following is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards m SD SDHC and SDXC memory cards appear the same externally However the logo on memory cards is different so pay careful attention to the logo when purchasing The SD memory card logo is S5 The SDHC memory card logo is 92 The SDXC memory card logo is 2 E The maximum capacity of SD memory cards is 2 GB The maximum capacity of SDHC memory cards is 32 GB The maximum capacity of SDXC memory cards is 128 GB Memory media format User s Manual New media cards are formatted according to specific standards If you wish to reformat a media card be sure to do so with a device that uses media cards Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards If you reformat a memory card be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards not with the format command provided within Windows 4 26 gl To format all areas of the memory card including the protected area you J must obtain an appropriate application that applies the copy protection system Media care Observe the following precautions when handling the card H Do not twist or bend cards Do not expose c
115. ould not be used outside this region For use in other regions buy power cords that conform to safety rules and regulations in the particular region Do not use a 3 pin to 2 pin conversion plug When you connect the AC adaptor to the computer always follow the Steps in the exact order as described in this User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts Never place your computer or AC adaptor on a wooden surface furniture or any other surface that could be marred by exposure to heat since the computer base and the surface of the AC adaptor increase in temperature during normal use Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions 1 Connect the power cord to the AC adaptor Figure 2 1 Connecting the power cord to the AC adaptor 2 pin plug PRS Figure 2 2 Connecting the power cord to the AC adaptor 3 pin plug ED y Either a 2 pin or 3 pin adaptor cord is included with the computer I depending on the model User s Manual 2 Connect the DC output plug of the AC adaptor to the DC IN 19V jack on your computer
116. ower radio stations for mobile object identification systems RFID used in factory production lines Other Radio Stations 1 Before using this equipment ensure that it does not interfere with any of the equipment listed above User s Manual 2 If this equipment causes RF interference to other radio stations promptly change the frequency being used change the location of use or turn off the source of emissions 3 Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations 2 Indication for Wireless LAN The indication shown below appears on this equipment 1 2 34 eee 2 4 This equipment uses a frequency of 2 4GHz DS This equipment uses DS SS modulation OF This equipment uses OFDM modulation 4 The interference range of this equipment is less than 40m This equipment uses a frequency bandwidth from 2 400MHz to 2 483 5MHz It is possible to avoid the band of mobile object identification systems arkwWNs gt 3 Indication for Bluetooth The indication shown below appears on this equipment 1 2 3 Lt 4 2 4 This equipment uses a frequency of 2 4 GHz FH This equipment uses FH SS modulation 1 The interference range of this equipment is less than 10m This equipment uses a frequency bandwidth from 2 400 MHz to 2 483 5 MHz It is impossible to avoid the band of mobile object identification systems
117. places subject to vibration such as airplanes trains or cars In addition do not use the computer on an unstable surface such as a stand Keep mobile phones and other wireless communication devices away from the computer CyberLink PowerDVD for TOSHIBA Be aware of the following limitations when you use the CyberLink PowerDVD for TOSHIBA Notes on use User s Manual This software can only be used on Windows operating system CyberLink PowerDVD for TOSHIBA is only provided with models configured with a DVD Super Multi drive CyberLink PowerDVD for TOSHIBA software is supported for playback of DVD and video file Frame dropping audio skipping or out of sync audio and video may occur during playback of some video titles Close all other applications when using the CyberLink PowerDVD for TOSHIBA Do not open any other applications or carry out any other operations during video playback Playback may stop or not function properly in some situations Unfinalized DVDs created on home DVD recorders may not be playable on the computer Use DVD Video discs with a region code which is either the same as the factory default setting if applicable or ALL Do not playback video while watching or recording television programs using other applications Doing so may cause video playback or television program recording errors In addition if prescheduled recording starts during video playback it may cause video playback or television pro
118. ple s faces You can easily create a polished slideshow or video of your digital life utilizing your photos and videos This utility is only provided with some models To access it clickCyberLink MediaStory in the Apps view For details on how to use CyberLink MediaStory please check out the tutorials by clicking Preferences fg in the main window and then clicking Tutorials Do not change the display device while running CyberLink MediaStory i User s Manual 5 3 TOSHIBA Function This utility allows you to perform some features Key by pressing a specified key or combined with the FN key To set up this utility click Function Key under TOSHIBA group in the Apps view For details refer to the Function Key section TOSHIBA Service This application allows your computer to Station automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs When enabled this application periodically transmits to our servers a limited amount of system information which will be treated in strict accordance with the rules and regulations as well as applicable data protection law To access this utility click Service Station under TOSHIBA group in the Apps view TOSHIBA PC Health The TOSHIBA PC Health Monitor application Monitor proactively monitors a number of system functions such as power consumption battery health and system cooling informing you of
119. ply 10 GND Ground 11 Reserved Reserved 12 SDA Serial Data Signal VO 13 HSYNC Horizontal Sync Signal O 14 VSYNC Vertical Sync Signal O 15 SCL Serial Clock Signal O I O I Input to computer I O O Output from computer User s Manual 7 2 AC Power Cord and Connectors The AC input plug of the power cord must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Certification agencies User s Manual China CQC U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 Australia AS Japan DENANHO Europe Austria OVE Italy IMQ Belgium CEBEC The Netherlands KEMA Denmark DEMKO Norway NEMKO Finland FIMKO Sweden SEMKO France LCIE Switzerland SEV Germany VDE United Kingdom BSI In Europe two conductors power cord must be VDE type HOSVVH2 F or HO3VVH2 F and for three conductors power cord must be VDE type HOSVV F For the United States and Canada two pin plug configuration must be a 2 15P 250 V or 1 15P 125 V and three pin plug configuration must be 6 15P 250 V or 5 15P 125 V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part Il The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia
120. point there You can see all of your recently used apps on the Windows Taskbar Power Options icon The Start screen provides you a convenient way to enter the Shut Down Sleep Hibernation Mode You can just click the power icon Q on the upper right of the Start screen and then select the mode you want Charms User s Manual Use the Windows charms to start apps find documents set up system components and perform most other computing tasks By pointing the mouse pointer to the upper or lower right of your screen you can find a list of charms Search Share Start Devices and Settings Search This charm allows you to search your computer apps settings and files the web or within an app You can also find the Search icon on the upper right of the Start screen Share This charm allows you to share items links photos and more rT Start This charm takes you to the Start screen or if am already on the Start screen returns you to your last app Devices This charm allows you to manage your hardware ro Settings This charm allows you to access your computer settings volume brightness connecting to the internet and more Tiles Tiles can be accessed and launched from the Start screen Typical Start screen tiles are the Desktop tile and Mail tile as well as tiles representing all other applications downloaded to your system Windows Store Although many applications are pre installed or built i
121. power is exhausted to the point that computer operation cannot be continued the system automatically enters Hibernation Mode and shuts itself down This can be specified in the Power Options Sleep Mode If you have to interrupt your work you can use this feature to allow you to turn off power to the computer without exiting from your software Data is maintained in the computer s main memory so that when you next turn on the power you can continue working right where you left off Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software The contents of main memory are automatically saved to the Hard Disk Drive so that when you next turn on the power again you can continue working right where you left off Refer to the Turning off the power section for more details USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports For example if a mouse or USB keyboard is connected to a USB port clicking the mouse button or pressing the keyboard will wakeup the computer Heat dispersal 1 To protect against overheating the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer s internal temperature rises to a certain level You are able to select whether to control this temperature by either turning on the fan first then if ne
122. puter before trying to monitor the remaining operating time This is because the computer needs this time to check the remaining capacity of the battery and then calculate the remaining operating time based on this together with the current power consumption E Be aware that the actual remaining operating time might differ slightly from the calculated time With repeated discharges and recharges the battery capacity will gradually decrease In view of this it is noted that an often used older battery will not operate for as long as a new battery even when both are fully charged Maximizing battery operating time User s Manual The usefulness of a battery depends on how long it can supply power on a single charge while how long the charge lasts in a battery depends on Processor speed Screen brightness System Sleep Mode System Hibernation Mode Display power off period Hard Disk Drive power off period How often and for how long you use the Hard Disk Drive and external disk drives for example optical disc How much charge the battery contained to begin with How you use optional devices such as a USB device to which the battery supplies power m Whether you enable Sleep Mode which can conserve battery power if you are frequently turning the computer off and on m Where you store your programs and data m Whether you close the display panel when you are not using the keyboard closing the display saves power E The
123. r is Tim Hudson tjh cryptsoft com Copyright remains Eric Youngs and as such any Copyright notices in the code are not to be removed If this package is used in a product Eric Young should be given attribution as the author of the parts of the library used This can be in the form of a textual message at program startup or in documentation online or textual provided with the package Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgement This product includes cryptographic software written by Eric Young eay cryptsoft com The word cryptographic can be left out if the rouines from the library being used are not cryptographic related 4 If you include any Windows specific code or a derivative thereof from the apps directory application code you must include an acknowledgement This product includes software written by Tim Hudson tjh cryptsoft com THIS SOFTWARE IS PROVIDED BY ERIC YOUNG
124. racter string to register the password enter from the keyboard character by character and do not enter as ASCII code or copy and paste the character string In addition ensure that the registered password is correct by outputting the character string to the password file When entering a password do not enter any characters for example I or produced by pressing the SHIFT or ALT keys Delete button Click this button to delete a registered password Before you can delete a password you must first enter the current password correctly Change button Click this button to change a registered password Before you can change a password you must first enter the current password correctly Owner String text box You can use this box to associate text with the password After you enter text click Apply or OK When the computer is started this text is displayed together with the prompt asking you to enter a password You can use BIOS Setup to set change or delete the HDD Password or HDD Master Password Tostart BIOS Setup 1 Click the power icon l on the Start screen and then select Restart 2 Hold down the F2 key and then release this key one second after the computer is power on the BIOS setup utility will load Toend the BIOS Setup press F10 and then select Yes to accept the changes The computer will restart m fyou forget your HDD User Password TOSHIBA will NOT be able to assist you and
125. rate these characters using their specific ASCII codes 1 Hold down the ALT key 2 Using the numeric keypad type the ASCII code of the character you require 3 Release ALT the ASCII character will appear on the display screen Optical disc drives The computer may be installed with a DVD Super Multi drive or Blu ray Writer drive BDXL When the computer is accessing an optical disc the indicator on the drive glows Formats User s Manual The drives support the following formats DVD Super Multi drive The drive supports the following formats CD ROM DVD ROM DVD Video CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA Addressing Method 2 DVD R DVD RW DVD R DVD RW DVD RAM DVD R DL Format1 DVD R DL Blu ray Writer drive In addition to the above formats Blu ray Writer drive supports BD ROM BD ROM DL BD R BD R DL BD RE and BD RE DL Blu ray Writer drive BDXL In addition to the above formats Blu ray Writer drive BDXL supports BD R TL BD R QL and BD RE TL 1 Some types and formats of DVD R DL and DVD R DL discs might be J unreadable Using optical disc drives The full size drive provides high performance execution of disc based programs You can run either 12 cm 4 72 or 8 cm 3 15 discs without an adaptor 7 Use the DVD playback application to view DVD Video discs For precautions on
126. read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location m Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure E Toprevent direct exposure to the laser beam do not try to open the enclosure Location of the Required Label Sample shown below Location of the label and manufacturing information may vary Location of the required label THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANU FACTURE TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F Bldg No 102 Digital empire2 486 Sin dong Yeongtong gu Suwon si Gyeonggi do Korea 443 734 Precautions CLASS TLASER PRODUCT CAUTION This appliance contains Sacre aria 1 PRODUKT a laser system and is classified as a 23A 1 VP BLA CLASS 1 LASER PRODUCT To use this model properly read the instruction manual carefully and keep this manual for your future reference In case of any trouble with this model please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure User s Manual 1 10 General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should
127. replug it wait at least 5 seconds before you replug the HDMI cable again When you change the display output device the playback device may not switch automatically In this case in order to set the playback device to the same device as the display output device please adjust the playback device manually by the following steps 4 30 1 Click Control Panel gt Hardware and Sound gt Sound under Windows System in the Apps view 2 In the Playback tab select the playback device which you want to switch to 3 To use the internal speakers on your computer select Speakers To use the television or the external monitor that you have connected to the computer select a different playback device 4 Click the Set Default button 5 Click OK to close the Sound dialog Settings for display video on HDMI To view video on the HDMI display device be sure to configure the following settings otherwise you might find that nothing is displayed Be sure to use the function key to select the display device before starting to play video Do not change the display device while playing video Do not change the display device under the following conditions E While data is being read or written E While communication is being carried out Selecting HD Format To select the display mode do the following 1 Click Control Panel gt Appearance and Personalization gt Display gt Change display settings gt Advanced settings gt Li
128. riting or rewriting User s Manual H Based on TOSHIBA limited compatibility testing we suggest the following manufacturers of disc media however it must be noted that disc quality can affect write or rewrite success rates Also be aware that in no event does TOSHIBA guarantee the operation quality or performance of any disc CD R TAIYO YUDEN CO Ltd MITSUBISHI KAGAKU MEDIA CO LTD CD RW Multi Speed High Speed and Ultra Speed MITSUBISHI KAGAKU MEDIA CO LTD DVD R DVD Specifications for Recordable Disc for General Version 2 0 TAIYO YUDEN Co Ltd for 8x and 16x speed media MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 16x speed media DVD R DL MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD R MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 16x speed media DVD R DL MITSUBISHI KAGAKU MEDIA CO LTD for 8x speed media DVD RW DVD Specifications for Recordable Disc for Version 1 1 or version 1 2 MITSUBISHI KAGAKU MEDIA CO LTD for 2x 4x and 6x speed media DVD RW MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD RAM DVD Super Multi drive only DVD Specifications for DVD RAM Disc for Version 2 0 Version 2 1 or Version 2 2 Panasonic Corporation for 3x and 5x speed media BD R Panasonic Corporation BD R DL Panasonic Corporation BD RE Panasonic Corporation BD RE DL Panasonic Corporation BD R TL TDK Corporation BD RE TL Panasonic Corporation
129. rnal displays or TV that have HDCP supported HDMI port The video cannot be displayed on an external display or TV connected to the RGB connector The Blu ray Disc movie can be played only on internal LCD displays or external devices connected via an HDMI output In Clone mode Dual View TOSHIBA Blu ray Disc Player might not function properly This product does not play HD DVD discs Blu ray discs with high definition content are required for HD viewing This software can only play back MPEG2 MP4 and WTV files created by the preinstalled applications on the same computer Playback might not function properly if you use the files other than these types The playback of some media files might not be normal by this player This might also happen when using Windows Media Player and Video app Display Devices amp Audio If the video image is not displayed on an external display or television stop the TOSHIBA Blu ray Disc Player and change the screen resolution To change the screen resolution click Control Panel gt Appearance and Personalization gt Display gt Adjust resolution under Windows System in the Apps view However video cannot be output to some external displays and televisions due to output or playback conditions When viewing video on an external display or TV change the display device before playing Video can be played only on internal LCD displays or external displays In Clone mode Dual View TOSHIBA Blu ray
130. rself Split Screen utility enables you to create multiple display zones on a screen and to fit the active windows to within those zones Resolution is an image processor that performs high quality image enhancements such as Color Correction and Sharpness on video playbacks This feature is only provided with some models To access this utility click Display Utility under TOSHIBA group in the Apps view For details on this utility see the help file This utility allows you to set a password in order to restrict access to the computer To access this utility click Password Utility under TOSHIBA group in the Apps view User s Manual TOSHIBA System Settings CyberLink PowerDVD for TOSHIBA TOSHIBA Blu ray Disc Player TOSHIBA Setup Utility This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use To access this utility click System Settings under TOSHIBA group in the Apps view This software is provided for playback of DVD Video To access this utility click CyberLink PowerDVD for TOSHIBA in the Apps view For details on how to use CyberLink PowerDVD for TOSHIBA see the help file This software is provided for playback of Blu ray Disc It has an on screen interface and functions To start this utility click TOSHIBA Blu ray Disc Player under TOSHIBA group in the Apps view For details on how to use TOSHIBA Blu ray Disc Player
131. s located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca Taiwan Article 12 Without permission granted by the NCC any company enterprise or user is not allowed to change frequency enhance transmitting power or alter original characteristic as well as performance to an approved low power radio frequency devices Article 14 The low power radio frequency devices shall not influence aircraft security and interfere legal communications If found the user shall cease operating immediately until no interference is achieved The said legal communications means radio communications is operated in compliance with the Telecommunications Act The low power radio frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices Using this equipment in Japan In Japan the frequency bandwidth of 2 400MHz to 2 483 5MHz for second generation low power data communication systems such as this equipment overlaps that of mobile object identification systems premises radio station and specified low power radio station 1 Important notice The frequency bandwidth of this equipment may operate within the same range as industrial devices scientific devices medical devices microwave ovens licensed radio stations and non licensed specified low p
132. s together to display a menu or other function depending on the software you are using Similar to right click Place two or more fingers down on the Touch Pad and move them toward each other pinch or away from each other stretch This shows different levels of information or visually zooms in or out Place two fingers down and slide them vertically or horizontally from anywhere on the Touch Pad This allows you to operate the scroll bars of a window Quickly move your finger in from the edge of the Touch Pad without pausing when you first touch it Swipe from the left edge shows your recently opened apps Swipe from the right edge opens or closes the charms Search Share Start Devices Settings Swipe from the top edge opens or closes the app command bar a Some of the Touch Pad operations described in this section are only J supported in certain applications The Keyboard The number of keys available on your keyboard depends on which country region your computer is configured for with keyboards being available for numerous languages There are different types of keys specifically typewriter keys function keys soft keys Windows special keys and the keypad overlay Never remove the key caps on your keyboard Failure to do so could damage the parts under the key caps Keyboard indicator The following figure shows the position of the CAPS LOCK indicator and NUM LOCK indicator which show the following
133. s injury Carefully clean the dust on the surface of the cooling vents using a soft cloth Back The following figure shows the back of the computer Figure 3 4 The back of the computer Product appearance depends on the model you purchased Battery pack The rechargeable lithium ion battery pack provides power to the computer when the AC adaptor is not connected For more detailed information on the use and operation of the battery pack refer to the Battery section Underside The following figures show the underside of the computer Ensure that the display is closed before the computer is turned over to avoid causing any damage Figure 3 5 The underside of the computer 2 CS gge 1 Battery lock 3 Battery pack 2 Battery release latch 4 Cooling vents Product appearance depends on the model you purchased User s Manual 3 5 ca Battery lock Slide the battery lock to release the battery pack ready for removal t 2 Battery release latch Slide and hold this latch into its Unlock position in order to release the battery pack for removal For more detailed information on removing the battery pack refer to the Battery section Cooling vents The cooling vents help the processor to avoid overheating Do not block the cooling vents Keep foreign metal objects such as screws staples and paper clips out of the cooling vents
134. s license grants a worldwide royalty free perpetual and irrevocable right and license to use execute perform compile display copy create derivative works of distribute and sublicense the FreeType Project in both source and object code forms and derivative works thereof for any purpose and to authorize others to exercise some or all of the rights granted herein subject to the following conditions H Redistribution of source code must retain this license file FTL TXT unaltered any additions deletions or changes to the original files must be clearly indicated in accompanying documentation The copyright notices of the unaltered original files must be preserved in all copies of source files H Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team in the distribution documentation We also encourage you to put an URL to the FreeType web page in your documentation though this isnt mandatory These conditions apply to any software derived from or based on the FreeType Project not just the unmodified files If you use our work you must acknowledge us However no fee need be paid to us 3 Advertising 7 21 User s Manual Neither the FreeType authors and contributors nor you shall use the name of the other for commercial advertising or promotional purposes without specific prior written permission We suggest but do not require that you use
135. s not operating properly keyboard Hard Disk Drive display panel Touch Pad Touch Pad control buttons as each device produces different symptoms Check the options within the operating system to ensure that its configuration is set properly What appears on the display Does it display any messages or random characters Make a screenshot of the current display and if possible look up the messages in the documentation included with the computer software or operating system Check that all connecting cables are correctly and firmly attached as loose cables can cause erroneous or intermittent signals Do any indicators light if so which ones what color are they and do they stay on or blink Write down what you see Do you hear any beeps if so how many are they long or short and are they high pitched or low pitched In addition is the computer making any unusual noises Write down what you hear Record your observations so you can describe them in detail to TOSHIBA Support Software The problems might be caused by your software or disk If you cannot load a software package the media might be damaged or the program might be corrupted In these instances try loading another copy of the software if possible If an error message appears while you are using a software package you should refer to the documentation supplied with it as this usually includes a problem solving section or a summary of error messages Next check
136. s recorded using home video camcorder and other content created by you can be played in either 2D or 3D using real time 2Dto3D conversion As for playback of 3D video content only Side by Side and Interleave 3D video formats are supported E Notall files can be played This section explains battery types use recharging methods and handling Battery pack User s Manual When the AC adaptor is not connected the main power source of the computer is this lithium ion battery pack also referred to in this manual as the main battery You can purchase additional battery packs for extended use of the computer away from an AC power source although you should not change the battery pack while the AC adaptor is connected Before you remove the battery pack save your data and shut down the computer or place the computer into Hibernation Mode Be aware that when placing the computer into Hibernation Mode the contents of memory are saved to the HDD SSD although for safety sake it is best to also save your data manually Real Time Clock RTC function The Real Time Clock RTC function is supported The main battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off If the RTC lasting time completely runs out the system will lose this information and the real time clock and calendar will stop working You can change the Real Time Clock settings
137. see the help file TOSHIBA Setup Utility is a BIOS setup utility that provides you a menu based user interface so that you can easily view and change BIOS settings TOSHIBA eco Utility This computer is equipped with eco mode This mode slightly lowers performance of some devices to reduce electric power consumption You can realize measurable power savings by using it continuously TOSHIBA eco Utility helps control the power consumption of your computer Various information can help you understand your degree of contribution to the environment Furthermore this utility contains Peak shift function that can help reduce power usage during periods of peak demand by shifting some power consumption to periods when demand is lower The utility also supports eco charge mode The battery will not be fully charged in this mode thus extending the life cycle of the battery It is recommended using the computer with AC adaptor connected as the battery operating time is comparatively short in this mode Depending on the usage situation the life cycle of the battery might not be extended properly To access this utility click eco Utility under TOSHIBA group in the Apps view For details on TOSHIBA eco utility see the help file CyberLink MediaStory CyberLink MediaStory helps you to quickly manage and share your multimedia content Your photos and videos are organized by event date in a calendar geographical places and by peo
138. significant system conditions This application recognizes the system and individual component serial numbers and tracks specific activities related to their usage To access this utility click PC Health Monitor under TOSHIBA group in the Apps view For details on TOSHIBA PC Health Monitor see the help file TOSHIBA Resolution The plug in lets you upconvert wmv and mp4 Plug in for Windows videos on Windows Media Player Media Player For more information refer to the TOSHIBA Resolution Plug in for Windows Media Player Help To access it click TOSHIBA Resolution Plug in for Windows Media Player Help under TOSHIBA group in the Apps view This utility will not be installed if the Resolution feature in TOSHIBA Display Utility is provided 1 You might not have all the software listed in this section depending on the D model you purchased User s Manual 5 4 Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use User s Manual Access each function using the following procedures 1 To access the Power Options click Control Panel gt System and Security gt Power Options under Windows System in the Apps view Display automatic power off HDD automatic power off System automatic Sleep Hibernation Mode 1 Power on password Intelligent power supply Battery save mode Panel power on o
139. sor is included in your model open the TOSHIBA PC Health Monitor utility by clicking PC Health Monitor under TOSHIBA group in the Apps view and then click PC Information For more information regarding CPU refer to the Legal Footnotes section Hard Disk Drive or Solid State Drive The capacity of the hard disk drive varies depending on the model To check which type of HDD SSD is included in your model open the TOSHIBA PC Health Monitor utility by clicking PC Health Monitor under TOSHIBA group in the Apps view and then click PC Information Note that part of the hard disk s overall capacity is reserved as administration space E n this manual the word HDD or Hard disk drive also refers to the SSD unless otherwise stated m SSD is a large capacity storage device which uses Solid State Memory in place of a magnetic disk of the hard disk Under certain unusual conditions of prolonged non use and or exposure to high temperatures the SSD might be vulnerable to data retention errors Legal Footnote Hard Disk Drive HDD Capacity For more information regarding Hard Disk Drive HDD Capacity refer to the Legal Footnotes section Video RAM Memory module The memory in the graphics adaptor of the computer used to store the image displayed on a bitmap display The amount of Video RAM available depends on the system memory of the computer Click Control Panel gt Appearance and Personalization gt Display
140. st All Modes under Windows System in the Apps view 2 Select one of the modes at List All Modes Wireless display User s Manual Your computer may support Wireless display a wireless technology which utilizes Wi Fi to allow the computer to be wirelessly connected to external displays including TVs as extended screens With Wireless display documents streamed local media contents or other online contents can be shared wirelessly with others To use Wireless display either one of the following devices is required Acompatible external display with built in support for Wireless display An external display with HDMI port and a Wireless display adaptor The Wireless display adaptor is a device that connects to the external display via HDMI port and can receive Wi Fi signals from your computer To wirelessly connect to an external display you can follow the steps as described below 4 31 1 Inthe Settings charm click Change PC settings gt PC and devices gt Devices 2 Click Add a device Your computer will start searching for the Wireless display device 3 After the Wireless display device is searched follow the on screen instructions to finish connection After the connection is established the name of the Wireless display device will appear under Projectors To disconnect the Wireless display device click the Wireless display device name and then click Remove device Changing the display settings After
141. t not be possible to make a network connection to a specified network name using the ad hoc network function If this occurs the new network has to be configured for all computers connected to the same network in order to re enable network connections Make sure to use new network name Security TOSHIBA strongly recommends that you enable encryption functionality otherwise your computer is open to illegal access by an outsider using a wireless connection If this occurs the outsider might illegally access your system eavesdrop or cause the loss or destruction of stored data H TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof Card Specifications Compatibility IEEE 802 11 Standard for Wireless LANs Network Operating B Microsoft Windows Networking System Media Access HB CSMA CA Collision Avoidance with Protocol Acknowledgment ACK Radio Characteristics Radio Characteristics of Wireless LAN module might vary according to H Country region where the product was purchased E Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4 GHz and 5 GHz band local radio regulations might impose a number of limitations to the use of wireless communication equipment Radio Frequency E Band 5 GHz 5150 5850
142. t open fully when you press the eject button Removing discs To remove the disc do the following Do not press the eject button while the computer is accessing the optical disc drive Wait for the optical disc drive indicator to go out before you open the disc tray Also if the disc is spinning when you open the disc tray wait for it to stop before you remove it 1 To pop the disc tray partially open press the eject button Gently pull the disc tray out until it is fully opened A When the disc tray pops open slightly wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open 2 The disc extends slightly over the sides of the disc tray so you can grasp it Gently lift out the disc 3 Push the center of the disc tray to close it Press gently until it locks into place How to remove disc when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off If the power is off you can open the disc tray by inserting a slender object about 20 mm such as a straightened paper clip into the manual eject hole near the eject button Figure 4 4 Manual release with the eject hole Product appearance depends on the model you purchased 1 Manual eject hole Turn off the power before you use the manual eject hole If the disc is spinning when you open the disc tray the disc could fly off the spindle and cause injury Writable discs
143. t that time please read the manual of the monitor and set the display mode which is supporting at the monitor Then it will be displayed with suitable size with correct aspect ratio 4 29 T User s Manual The HDMI out port HDMI High Definition Multimedia Interface port digitally transfers both video and audio data without reducing the quality HDMI compatible external display devices including televisions can be connected via the HDMI port Some models can support ultra high definition 3840 x 2160 pixels display on compatible external display devices via HDMI output port To use this function you must purchase an HDMI cable corresponding to 3840x2160 pixels or higher To connect an HDMI compatible display device do the following To connect a device to the HDMI out port you must purchase a suitable HDMI cable 1 Plug one end of the HDMI cable into the HDMI in port of the HDMI display device 2 Plug the other end of the HDMI cable into the HDMI out port on your computer 3 Turn the HDMI display device s power on Figure 4 10 Connecting the HDMI out port 1 HDMI out port 2 HDMI cable Product appearance depends on the model you purchased Do not plug unplug an HDMI device under the following conditions m The system is starting up m The system is shutting down When you connect a television or external monitor to the HDMI port the display output device is set to HDMI When you unplug the HDMI cable and
144. ternal 3D devices connected via an HDMI output It cannot be shown on the internal display In order for 3D playback to work on external display TV you need a 3D enabled display TV that has an HDCP compliant HDMI port 7 3D playback feature supports the following resolutions 1920x1080 24Hz Dl and 1280x720 60Hz Please change the Screen Resolution to one of the above before using 3D playback function Important Safety Information for 3D Function E Refrain from or stop viewing if you feel ill or experience discomfort before or while watching 3D video images H Refrain from viewing 3D video images if you experience convulsions photosensitivity reaction or heart disease H Due to the possibility of impact on vision development viewers of 3D video images should be aged 6 or older Children and teenagers might be more susceptible to health issues associated with viewing in 3D and should be closely supervised to avoid prolonged viewing without rest E Avoid use of the 3D function when under the influence of alcohol E Read the user s manual that comes with the computer carefully before using the 3D playback function mH The 3D effect differs between individuals Notes on 3D Playback for TOSHIBA Blu ray Disc Player The 3D playback function can playback 3D video content and your 2D home video content and other 2D content created by you DVD or video file in 3D using real time 2Dto3D conversion m The 3D playback function CANNOT
145. tilized system memory size and other factors If your computer is configured with more than 3 GB memory the memory might be displayed as approximately 3 GB only depending on the hardware specifications of the computer This is correct because the operating system usually displays the available memory instead of the physical memory RAM built into the computer Various system components like the video adapter s GPU and PCI devices like Wireless LAN and so on require their own memory space Since a 32 bit operating system cannot address more than 4 GB of memory these system resources overlap the physical memory It is a technical limitation that the overlapped memory is not available to the operating system Even though some tools might display the actual physical memory built into your computer the memory available to the operating system is still approximately 3 GB only Computers configured with a 64 bit operating system can address 4 GB or more of system memory Battery Life User s Manual Battery life might vary considerably depending on product model configuration applications power management settings and features utilized as well as the natural performance variations produced by the design of individual components Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication Recharge time varies depending on usage Battery might not charge while comp
146. ting or video conferences using a communication tool Do not point the web camera directly at the sun Do not touch or press strongly on the web camera lens Failure to do so might reduce image quality Use an eyeglass cleaner cleaner cloth or other soft cloth to clean the lens if it becomes dirty Wireless communication antennas Depending on the configuration of your computer one or all of the following antennas are built in m Wireless LAN H Wireless LAN Bluetooth Legal Footnote Wireless LAN For more information regarding Wireless LAN refer to the Legal Footnotes section 3 7 Display screen Legal Footnote LCD 41 3 cm 17 3 LCD screen configured with one of the following resolutions HD 1600 horizontal x 900 vertical pixels E FHD 1920 horizontal x 1080 vertical pixels Be aware that when the computer is operating on the AC adaptor the image displayed on the internal screen is somewhat brighter than when it operates on battery power This difference in brightness levels is intended to save power when operating on batteries For more information regarding LCD refer to the Legal Footnotes section Stereo speakers Display hinges Power button Power indicator Keyboard Touch Pad The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system The display hinges allow the display panel to be positioned at a vari
147. tion required for network and service supply This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny Alesund Only for indoor applications Restrictions for Use of 5150 5350MHz Frequencies in Europe Italy Luxembourg Implemented For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply Russian Limited Federation e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m Restrictions for Use of 5470 5725MHz Frequencies in Europe Italy Luxembourg Implemented Russian Limited Federation For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at a
148. tions under Windows System in the Apps view 2 Click Choose what the power button does or Choose what closing the lid does 3 Click Change settings that are currently unavailable 4 Select the Hibernate check box from Shutdown settings 5 Click the Save changes button Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid To define these settings do the following 1 Click Power Options and then click Choose what the power button does or Choose what closing the lid does 2 Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid 3 Click the Save changes button Data save in Hibernation Mode When you turn off the power in Hibernation Mode the computer takes a moment to save the current data in memory to the Hard Disk Drive After you turn off the computer and the content of memory has been saved to the Hard Disk Drive turn off the power to any peripheral devices AN Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge User s Manual 2 12 Chapter 3 The Grand Tour 7 This chapter identifies the various components of the computer It is recommended that you become familiar with each before you operate the computer Legal Footnote Non applicable Icons For more information regarding Non applicable Icons refer t
149. toring the pre installed software from the Recovery Hard Disk Drive Creating Recovery Media i User s Manual This section describes how to create Recovery Media Be sure to connect the AC adaptor when you create Recovery Media Be sure to close all other software programs except the Recovery Media Creator Do not run software such as screen savers which can put a heavy load on the CPU Operate the computer at full power Do not use power saving features Do not write to the media when the virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background Do not use utilities including those intended to enhance Hard Disk Drive access speed They might cause unstable operation and damage data Do not shut down log off or Sleep Hibernate while writing or rewriting the media Set the computer on a level surface and avoid places subjected to vibrations such as airplanes trains or cars Do not use on an unstable surface such as a stand A recovery image of the software on your computer is stored on the Hard Disk Drive and can be copied to either disc media or USB Flash Memory by using the following steps 1 Select either blank disc or USB Flash Memory The application allows you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory E So
150. ts USB bus power DC5V supply might be stopped for safety reasons m When Sleep and Charge function is enabled the USB Wakeup function might not work for compatible ports In that case if there is a USB port that does not have the Sleep and Charge function attach the mouse or keyboard to it If all USB ports have the Sleep and Charge function change to disable Sleep and Charge function The USB Wakeup function now works but the Sleep and Charge function is disabled Metal paper clips or hair pins clips can generate heat if they come into contact with USB ports Do not allow USB ports to come into contact with metal products for example when carrying the computer in your bag Your PC has multiple charging modes so that many different USB devices can be supported for Sleep and Charge function Auto Mode Default is suitable for a wide range of digital audio players While using Auto Mode your computer can supply USB bus power at maximum 2 0A to the compatible ports while the computer is turned off When USB device cannot be charged by Auto Mode change to Alternate Mode This function might not be able to be used with some connected external devices even if the appropriate mode is selected In this situation disable and stop using this function Some external devices cannot use Auto Mode As for the specifications of the external devices contact the device s manufacture or check the specifications of the external device thorough
151. ut USB Sleep and Charge function or disable System ON CDP Charge Mode It is recommended that AC adaptor is connected to the computer while supplying USB bus power DCS5V 1 5A When your computer battery capacity is too low to continue System ON CDP Charge Mode might not work In those cases connect the AC adaptor and reboot the computer Always use the USB cable that was included with your USB device When System ON CDP Charge Mode or USB Sleep and Charge function is enabled the USB Wakeup function might not work In that case use a USB port without USB Sleep and Charge function or disable both System ON CDP Charge Mode and USB Sleep and Charge function TOSHIBA PC Health Monitor User s Manual The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption battery health for models with battery and the system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and tracks specific activities related to the computer and their usage The collected information includes device operation time and number of actuations or status changes that is number of power button and FN key combination uses AC adaptor battery for models with battery LCD fan for models with fan HDD SSD sound volume wireless communication functionalities and USB information d
152. uter is consuming full power After going through many charge and discharge cycles the battery will lose its ability to perform at maximum capacity and needs to be replaced This is a normal phenomenon for all batteries To purchase a new battery pack see the accessories information that is shipped with your computer Hard Disk Drive HDD Capacity LCD 1 Gigabyte GB means 10 1 000 000 000 bytes using powers of 10 The computer operating system however reports storage capacity using powers of 2 for the definition of 1 GB 230 1 073 741 824 bytes and therefore shows less storage capacity Available storage capacity will also be less if the product includes one or more pre installed operating systems such as Microsoft Operating System and or pre installed software applications or media content Actual formatted capacity might vary Over a period of time and depending on the usage of the computer the brightness of the LCD screen will deteriorate This is an intrinsic characteristic of LCD technology Maximum brightness is only available when operating in AC power mode Screen dims when the computer is operated on battery power and you might not be able to increase the brightness of the screen Graphics Processing Unit GPU Graphics processing unit GPU performance might vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized w
153. uuiedecnadeeivdnecedeadaneedsng 4 28 Chapter 5 Chapter 6 Chapter 7 User s Manual Security JOCK wisiincecceicenteciriannecesssveecetedeusdeseesseeeastacdeudenesdesunewennaeeucisnendtiy 4 32 Optional TOSHIBA Accessories eceeeeeeeeeeeeeeneeneeeeeeneeeeeeeennsneeenes 4 33 Sound System and Video mode scccesseceeeeeeeneeeeeeeseneeeenenennsnenenes 4 33 Utilities and Advanced Usage Utilities and Applications cccccceceseeeee ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 5 1 Special features cceeeccsseee esse eeeeeeeeeseeeeeeeeeseseeeeeeseneeesseeseesseesesseneeneees 5 5 TOSHIBA Password Utility cceeccssseeeeeseeeeeeeeeseseeeeseeneneeeeeensenenenes 5 6 TOSHIBA System SettingS ccceeceseseeeeeeeeeeeeeeesseeeeeeeeeeeeseensnsneeenes 5 9 USB Ch i sciis cavsieasevcacivcutedevsauabbentaie catcenuudasennadesduncaeviwancoasee 5 10 TOSHIBA PC Health Monitor ccscccecececeeseeeeeeeeeeeeeeeeseeneeseneeseeeeenes 5 12 System Recovery u ccceceecceseeeeseseeeeseeeeseneeeesnsenseseeeesesaeeeseseeaeeeeeesnnsoneeees 5 14 Troubleshooting Problem solving process ccccceeeeseeeeeeeeeeeee eee eeeeeeeeeeeseeeeseaeeeeeeeees 6 1 Hardware and system checklist ccccceeesesseeeeeseeeeeeeeeeesseeeeseeeneeeseeens 6 4 TOSHIBA support 00 ce cece ceeeeee seen eneseeesneeeeeesseneeeseeesneneeesnsoneeeneenennseaees 6 16 Appendix Specifications sensona aanas fete tates en eee 7 1 AC Power Cor
154. video image is not displayed on an external display or television stop the CyberLink PowerDVD for TOSHIBA and change the screen resolution To change the screen resolution click Control Panel gt Appearance and Personalization gt Display gt Adjust resolution under Windows System in the Apps view However video cannot be output to some external displays and televisions due to output or playback conditions When viewing video on an external display or TV change the display device before playing Video can be played only on internal LCD displays or external displays In Clone mode Dual View CyberLink PowerDVD for TOSHIBA may not function properly Do not change the screen resolution while running the CyberLink PowerDVD for TOSHIBA Do not change the display device while running the CyberLink PowerDVD for TOSHIBA Starting CyberLink PowerDVD for TOSHIBA Use the following procedure to start CyberLink PowerDVD for TOSHIBA 1 Insert a DVD Video in the optical disc drive while the operating system is running When a DVD Video disc is set in the DVD drive for models with DVD drive CyberLink PowerDVD for TOSHIBA may start automatically Click CyberLink PowerDVD for TOSHIBA in the Apps view to start CyberLink PowerDVD for TOSHIBA Operating CyberLink PowerDVD for TOSHIBA Notes on Using CyberLink PowerDVD for TOSHIBA Screen display and available features may vary amongst videos and scenes Open CyberLink PowerDVD for TOSHI
155. window appears 2 Select the program you want to close then click End Task Closing the failed program should allow you to continue working If it does not continue with the next step 3 Close the remaining programs one by one by selecting the program name then End Task Closing all programs should allow you to continue working If it does not power off your computer and then restart it The computer does not start Make sure that you attached the AC adaptor and power cord cable properly If you are using the AC adaptor check that the wall outlet is working by plugging in another device such as a lamp Verify that the computer is on by looking at the Power indicator If the indicator is glowing the computer is on Also try turning the computer off and then on If you are using an AC adaptor verify that the computer is receiving power from the external power source by looking at the DC IN Battery indicator If the indicator is glowing the computer is connected to a live external power source The computer does not load advanced options during startup By holding down one of the following keys during startup your computer can load the following advanced options Key Advanced option F2 BIOS utility F12 Boot menu 0 zero Recovery options If your computer starts to load the Operating System instead of desired advanced options do the following 1 Click the power icon Q on the Start screen and then select
156. without the permission of the copyright owner is a violation of copyright or author s rights and is subject to civil damages or criminal action Comply with copyright laws in making any reproduction from this manual Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for your computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the computer and the manual Trademarks Intel Intel SpeedStep Intel Core and Centrino are trademarks or registered trademarks of Intel Corporation AMD the AMD Arrow logo PowerPlay Vari Bright and combinations thereof are trademarks of Advanced Micro Devices Inc User s Manual 1 1 Windows Microsoft and Windows logo are registered trademarks of Microsoft Corporation The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Toshiba Corporation and its affiliates is under license The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries CyberLink CyberLink PowerDVD and CyberLink MediaStory are registered trademarks of CyberLink Corporation
157. you use this equipment in the countries regions which are not listed in the following table contact TOSHIBA Support As of November 2014 Austria Belgium Bulgaria Canada Cyprus Czech Rep Denmark Estonia Finland France Germany Greece Hong Kong Hungary Iceland India Indonesia Ireland Italy Japan Korea Latvia Liechtenstein Lithuania Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA Legal Footnotes Non applicable Icons CPU User s Manual Certain computer chassis are designed to accommodate all possible configurations for an entire product series Therefore be aware that your selected model might not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis Central Processing Unit CPU Performance Legal Footnotes CPU performance in your computer product might vary from specifications under the following conditions muse of certain external peripheral products muse of battery power instead of AC power muse of certain multimedia computer generated graphics or video applications use of standard telephone lines or low speed network connections use of complex modeling software such as high end computer aided design applications m use of several applications or functionalities simultaneously muse of computer in areas with low air pressure high altitude gt 1 000 meters or

User`s Manual - CNET Content Solutions

Contents

Download Pdf Manuals

Related Search

Related Contents