opc server for devices aist and imldc
Contents
1. Cancel Figure 3 5 Installation completed INSTALLATION OF THE OPC SERVER 7 USER S MANUAL 4 DESCRIPTION OF THE PRODUCT REGISTRATION PROCEDURE When starting an unregistered copy of the software the user is offered to register his or her copy of the OPC server Registration is undertaken by means of the dialog box presented in Figure 4 1 Also the OPC server allows calling the registration dialog box by using the Help Registration menu command when the server is running in configuration mode OPC Server for AIST and IMLdC devices Registration SPC KRUG 1 Titova str Penza 440028 Russia Company name Phone 8412 55 64 95 8412 55 64 97 Fax 8412 55 64 96 Your code e mail support krug2000 ru 8879F588 436E Our site www krug2000 ru Your key In order to get the key please contact us and announce your user name company name and your code Figure 4 1 Product registration dialog box To register the copy of the software you should contact SPC KRUG either by phone fax or email the relevant information is presented in the dialog box and report the following data User name e Company name Your code The value of this field is generated automatically based on the hardware configuration of the workstation After registering your copy SPC KRUG will deliver to you the key allowing you to use the OPC server2. Flags P gt 2 15 MPa PTR_P_HIGH b TRD work mode 59 Mode PTR_REJIM 0 automatic 1 manual 60 Gas gryogen mass PVK_M_GOS ee 40 95 Gas cryogen emission 61 Start PVK_PUSK mode WCD 1 active status 62 Weight Checking es ee PVK_ZPU_CLOSE pee status Device evice is stoppe 1 active 63 Mass and Flags The stop starting PVK_ZPU_OPEN SSD status device is started 1 active Weight control unit 64 Mode PVK_REJIM ee i 0 automatic 1 manual 65 AB Accumulator Gas cryogen LEEK GOS Maximum value 2 55 Battery Voltage leakage Z tons and 66 GC Gas cryogen Battery voltage U_AKB Maximum value 25 5 V Leakage 22 APPENDIX A OPC server for devices AIST and IMLDC Continuation of table A 1 2 List of parameters for the control cabinet of IMLDC Ne Parameter type Parameter name OPC server s tag name Remarks The number of The number of 67 AB Accumulator battery cycles AM_PWR Maximum value 8191 ea The number of the 0 battery 1 68 PU Power Unit battery connected NUMBER 1 battery 2 to the resistor Flags 69 E20 is faulty E20 BAD 70 E20 is on E20 ON 71 TCD E10 is on E10 BAD 72 Temperature E10 is faulty E10 ON 73 Control Device A1 is on A1_ON Stat f refri ti 74 Flags A1 is faulty A1 BAD ans a lon 75 A2 is on A2_ON 76 A2 is faulty A2_BAD APPENDIX A 23
3. DESCRIPTION OF THE PRODUCT REGISTRATION PROCEDURE UNINSTALLING THE OPC SERVER BASIC FEATURES AND WORKING PRINCIPLES 6 1 Features of the OPC server 6 2 OPC server s operations 6 2 1 Work modes 6 3 User s interface 6 3 1 Toolbar items 6 4 Configuring the OPC server 6 4 1 Creating a communication channel 6 4 2 Adding a device to the configuration 6 4 3 Adding a unit to the configuration for AIST devices 6 4 4 Searching for devices and units 6 4 5 Deleting a configuration element 6 4 6 Changing settings for a configuration element 6 4 7 Viewing parameter values of a configuration element 6 4 8 Saving configuration 6 4 9 Closing the configuration window 6 5 OPC server s functioning description 6 5 1 The main working algorithm of the OPC server APPENDIX A DEVICE PARAMETERS PROVIDED BY THE OPC SERVER A 1 List of device parameters provided by the OPC server A 1 1 List of parameters for AIST devices A 1 2 List of parameters for device IMLDC Page O aA KR Q OPC server for devices AIST and IMLDC 1 GENERAL INFORMATION The purpose of this manual is to explain to users the working principles of the OPC server for devices AIST and IMLDC version 1 01 hereinafter referred to as OPC server The document contains the description of the OPC server installation and uninstallation its modes and its user s interface along with the configuration procedure for its proper operation and full use of technical ca
4. the configuration of the OPC server Button for cancelling the search and closing the dialog box List of found devices Search progress indicator 6 4 5 Deleting a configuration element To delete a channel device unit from the configuration you should select it in the tree view and select the menu item Channel Delete Device Delete Unit Delete accordingly or click the button Delete on the toolbar 16 BASIC FEATURES AND WORKING PRINCIPLES OPC server for devices AIST and IMLDC 6 4 6 Changing settings for a configuration element To change parameters for a certain tree view item you should double click it Depending on the type of the item you will be shown either the communication channel properties dialog box Figure 6 3 or the device properties dialog box Figure 6 4 or the unit properties dialog box Figure 6 5 6 4 7 Viewing parameter values of a configuration element To view parameter values for channels devices and units you should select the corresponding item in the tree view The information about the item will automatically be displayed in the view area 6 4 8 Saving configuration In order to save configuration you should either select the menu item File Save or click the button Save on the toolbar 6 4 9 Closing the configuration window The configuration window can be closed either by selecting the appropriate item from the system menu or by selecting the men
5. OPC SERVER FOR DEVICES AIST AND IMLDC Version 1 01 User s Manual 2012 OPC server for devices AIST and MLDC Uer s Manual 1 edition This manual is for those who learn the functions and working principles of the OPC server for devices AIST Device receiving the control and management of fire and IMLDC Isothermal Module for storage of Liquid Dioxide of Carbon 1992 2012 SPC KRUG All rights reserved Registered trademark of the SPC KRUG No part of this publication for any purpose can not be reproduced in any form or by any means electronic or mechanical including photography magnetic recording or other means of copying or retention of information without the prior written permission of the copyright owners All trademarks and registered trademarks mentioned in this text are the property of their legal owners Suggestions and feedback related to the work of the OPC server content and design of the documentation should be addressed to SCIENTIFIC and PRODUCTION COMPANY SPC KRUG Ltd www krug2000 ru Address 1 Titova str Penza 440028 Russia Tel 7 841 2 49 97 75 multichannel Fax 7 841 2 55 64 96 E mail common questions info opcserver ru technical support support opcserver ru www OPCserver net www opcserver ru OPC server for devices AIST and IMLDC O na KR WHO DH A LQ CONTENTS GENERAL INFORMATION SYSTEM REQUIREMENTS INSTALLATION OF THE OPC SERVER
6. Tag s attributes e Current value e Access rights e Measurement units e Description e Value type e Value authenticity e Timestamp 18 BASIC FEATURES AND WORKING PRINCIPLES OPC server for devices AIST and IMLDC APPENDIX A DEVICE PARAMETERS PROVIDED BY THE OPC SERVER Device s tags are presented as follows lt Communication channel gt lt Device gt lt Unit gt lt Parameter gt for AIST devices lt Communication channel gt lt Device gt lt Parameter group gt lt Parameter gt for IMLDC devices where lt Communication channel gt COM port to which the device is connected This value corresponds to the value of the field Channel name specified while configuring lt Device gt the device to which the unit is connected This value corresponds to the value of the field Unit name specified while configuring lt Unit gt the unit with which the data exchange is performed for AIST devices The value corresponds to the value of the field Unit name specified when configuring lt Parameter group gt parameter group for IMLDC devices lt Parameter gt device s parameter Possible value of the fields lt Parameter group gt and lt Parameter gt are listed in tables A 1 1 and A 1 2 A 1 List of device parameters provided by the OPC server A 1 1 List of parameters for AIST devices Table A 1 1 List of
7. You need to specify it in the field Your key of the dialog box and afterwards fill all other fields of the form and click the button Register The OPC server can also be used in demo mode To run the server in this mode you should click the button Demo in the registration dialog box In this case you will be shown the window presented in figure 4 2 When running the server in demo mode you can use all the features of the OPC server but there is a time limitation 8 DESCRIPTION OF THE PRODUCT REGISTRATION PROCEDURE OPC server for devices AIST and IMLDC Attention The OPC server is being started in demo mode LY You can go on using the software in this mode For 30 days After the said period expires the demo mode wil no longer be available You wil need to register your copy of the OPC sever in order to go on using It Figure 4 2 Starting demo mode dialog box DESCRIPTION OF THE PRODUCT REGISTRATION PROCEDURE 9 USER S MANUAL 5 UNINSTALLING THE OPC SERVER To uninstall the OPC server please use the Settings Control panel menu item from the Start menu Please select Add remove programs Figure 5 1 F Add or Remove Programs Ioj xj V Show updates Sort by Name my IVI W To remove this program from your computer dick Remove Figure 5 1 Add remove program window Select the item OPC server for devices AIST and IMLDC click Re
8. aying device s parameter values There will be displayed the values for the currently selected tree view item 5 System menu It is designed for minimizing maximizing and closing the application window 6 Tree view item communication channel 7 Tree view item a device connected to the communication channel 8 Tree view item a unit connected to the device 6 3 1 Toolbar items In the upper part of the window underneath the main menu there is located the toolbar containing a set of command buttons You can invoke functions corresponding to toolbar items by clicking the appropriate button A tooltip containing additional information is displayed as the mouse cursor is hovering over a button 12 BASIC FEATURES AND WORKING PRINCIPLES OPC server for devices AIST and IMLDC ind Figure 6 2 The toolbar The toolbar contains the following items 1 Save configuration Add modify channel Add modify device Add modify unit Search for devices and units Delete configuration item oe a ae ee Show help 6 4 Configuring the OPC server Before connecting to the OPC server using an OPC client you should configure the OPC server In order to do it you must start it in configuration mode please refer to section 6 2 1 of this text While configuring the server you should specify the communication channels along with devices and units connected to them 6 4 1 Creating a communication channel In order to creat
9. e a communication channel you must select the menu item Channel Add Modify or click the button Add modify channel from the toolbar You will see the dialog box presented in Figure 6 3 Communication channel setup Channel WN COM port name Baud rate Number of atternpts coca _ Figure 6 3 Communication channel setup dialog box The dialog box has the following fields 1 Channel name 2 Number of COM port BASIC FEATURES AND WORKING PRINCIPLES 13 USER S MANUAL 3 Baud rate Number of attempts This parameter indicates the number of unsuccessful polling attempts after which the device is considered to be unavailable If you happen to experience frequent communication faults please try to augment this value When you click the button OK the specified channel will be added to the configuration If you click Cancel the channel will not be added 6 4 2 Adding a device to the configuration In order to add a device you must specify the channel to which the device is connected by selecting an appropriate element from the configuration tree view and either select the menu item Device Add Modify or click the button Add modify device on the toolbar You will be shown the dialog box presented in Figure 6 4 Device description 1 Device name 2 Device type Addres 3 Figure 6 4 Device properties dialog box The dialog box contains the following fields 1 D
10. e application will be installed The Wise Installation Wizard will install the files for OPC server for devices AIST and IMLDC in the following folder To install into a different folder click the Browse button and select another folder You can choose not to install OPC server for devices AIST and IMLDC by clicking Cancel to exit the Wise Installation Wizard Destination Folder C Program Files OPC server for devices AIST and IMLDC Figure 3 3 Install path selection window After selecting the installation path please click the Next gt button to continue installation i OPC server for devices AIST and IMLDC Setup Ready to Install the Application Click Next to begin installation Click the Back button to reenter the installation information or click Cancel to exit the wizard Cancel Figure 3 4 Setup parameters summary 6 INSTALLATION OF THE OPC SERVER OPC server for devices AIST and IMLDC If some parameters figure 3 4 do not satisfy you click lt Back to return to one the previous pages and make appropriate modifications If you agree with all the specified values click the button Next gt After finishing the procedure of copying the files you will be shown the window displayed in Figure 3 5 i OPC server for devices AIST and IMLDC Setup OPC server for devices AIST and IMLDC has been successfully installed Click the Finish button to exit this installation
11. evice name 2 A drop down list of supported devices AIST and IMLDC 3 Device address 1 to 16 Note 1 Because devices of both types cannot be used simultaneously on the same channel selection of device type is available only when the first device is added to a certain communication channel Note 2 Only one IMLDC device can be connected to a certain channel When you click OK the device will be added to the OPC server configuration If you click the button Cancel the device will not be added 14 BASIC FEATURES AND WORKING PRINCIPLES OPC server for devices AIST and IMLDC 6 4 3 Adding a unit to the configuration for AIST devices To add a unit you should specify an AIST device to which the unit is attached by selecting the appropriate tree view item After doing this you should select the menu item Unit Add Modify or click the button Add modify unit on the toolbar You will be shown the dialog box presented in Figure 6 5 Unit description Unit name Unit type Figure 6 5 Unit properties dialog box The dialog box contains the following fields 1 Device name 2 Drop down list of supported units for AIST device 3 Fields for unit address Depending on the device type some of the fields for unit address can be disabled All fields accept values from 1 to 4 When you click OK the unit will be added to the configuration of the OPC server If you click Cancel the u
12. led alarm OTV_POD 24 RCD Fault ER 25 Remote DD closed alarm RU_CLSD De ee DD opened alarm RU_OPND Device p 27 Fault ER 28 Powered by a backup source REZP Leak f th tinguishi 29 Station eakage of the extinguishing UT OTV agent alarm peuce Reduction of pressure in the 30 a eee DPBLOW motive cylinder motive flow 31 RCDPE Fault ER 32 uaciiote PE off signal PE_OFF Control Device of 33 Processing PE on signal PE ON Equipment 20 APPENDIX A OPC server for devices AIST and IMLDC A 1 2 List of parameters for device IMLDC Table A 1 2 List of parameters for the control cabinet of IMLDC Ne Parameter type Parameter name OPC server s tag name Remarks 1 TCD is faulty BVS_PTR_BAD 2 Tubular heater is BVS_TEN_BAD faulty 3 Refrigeration unit BVS_XA_BAD is faulty 4 P lt 1 95 MPa BVS_ P_LOW 5 P gt 2 15 MPa BVS_P_HIGH 6 Weight control unit BVS_PVK_BAD is faulty The motive BVS_PB_BAD To al cylinder is faulty The shut off and BVS_ZPU_BAD g BVS Data starting device is EARI faulty The shut shut off BVS_ZPU_CLOSE 9 and starting device is stopped The starting BVS_ZPU_OPEN 10 See device is started 11 Leakage BVS_LEEK The accumulator BVS_AKB_ BAD 12 val battery i
13. move You will be shown the dialog box presented in figure 5 2 OPC server for devices AIST and IMLDC Uninstall Are you sure you want to completely remove OPC server for devices AIST and IMLDC and all of its components Figure 5 2 Uninstall confirmation window If you click the button Yes the uninstall procedure will be started If you click No the operation will be cancelled 6 BASIC FEATURES AND WORKING PRINCIPLES 6 1 Features of the OPC server The OPC server implements the following main functions e Exchange of operative data with devices AIST and IMLDC The full list of device parameters provided by the OPC server is given in the Appendix A e The OPC server can use multiple channels simultaneously allowing to minimize overall time needed for the data exchange 10 MEHHCTAJIJIANNA OPC CEPBEPA OPC server for devices AIST and IMLDC e The OPC server can poll multiple devices connected to one communication channel simultaneous connection of both AIST and IMLDC devices is not allowed due to incompatibility of their data protocols e Interaction with OPC clients according to specification OPC Data Access version 2 05a 6 2 OPC server s operations 6 2 1 Work modes There are three work modes e Registration Unregistration mode e Configuration mode with configuration window e Main mode without configuration window Registration Unregistration mode this m
14. nit will not be added 6 4 4 Searching for devices and units To search for connected devices and units you should select the required communication channel in the configuration tree view select the Device Search menu item or click the button Search on the toolbar You will be shown the window presented in figure 6 5 When you click the button Start search the OPC server will try to detect AIST devices and units or a single IMLDC device The type of device being searched is determined by the switch 1 Devices are searched for at baud rate which is specified for the selected channel The resulting list will be updated as new devices and units are found If no devices or units were found the program will display a message informing about it BASIC FEATURES AND WORKING PRINCIPLES 15 USER S MANUAL If the search was successful you should select the devices which are to be added to the configuration and click the button Add refer to figure 6 6 If you click the button Cancel no devices or units will be added to the configuration 1 2 3 Search for devices and unit Figure 6 6 Search for devices and units dialog box The dialog box contains the following fields 1 ee oe oe Device type switch AIST or IMLDC Fields for specifying the address range for AIST devices Start stop search button Button for selecting all found devices in the list Button for adding found devices to
15. ode is started by running the OPC server with RegServer or UnRegServer command line arguments for registering or unregistering the server respectively The server is run in these modes automatically while installing and uninstalling the OPC server that is why you most probably will not have to run the server with these arguments if the installer is available Configuration mode with configuration window this mode started by the OPC server with Cfg command line argument This mode is designed for setting up working parameters for the OPC server You can start the OPC server in this mode by running the Start menu item corresponding to the OPC server The configuration parameters are saved in the file A ST cfg which is located in the same directory as the OPC server s executable file Main mode without configuration window this mode is started automatically as the first OPC client sends request to the OPC server using COM infrastructure 6 3 User s interface When the OPC server is launched in configuration mode the window presented in figure 6 1 is displayed on the screen BASIC FEATURES AND WORKING PRINCIPLES 11 USER S MANUAL Figure 6 1 The OPC server s configuration window The window contains the following elements Main menu Toolbar with command buttons which replicate the main menu items The tree view for displaying the hierarchy of devices A O N The area for displ
16. pabilities of devices AIST and IMLDC either independently or as part of multilevel automated systems The OPC server is implemented as an executable COM module OPCAISTSrv exe The OPC server supports the OPC DA specification version 2 05a GENERAL INFORMATION 3 USER S MANUAL 2 SYSTEM REQUIREMENTS In order to work with the OPC server the computer must meet the following requirements Processor Pentium 2 200 MHz RAM 64 MB e Free hard disk space 3 MB Serial port Operating system Windows XP 7 4 SYSTEM REQUIREMENTS OPC server for devices AIST and IMLDC 3 INSTALLATION OF THE OPC SERVER To install the OPC server run setup exe You will be shown the window presented in figure 3 1 ie OPC server for devices AIST and IMLDC Setup Welcome to the OPC server for devices AIST and IMLDC Installation Wizard It is strongly recommended that you exit all Windows programs before running this setup program Click Cancel to quit the setup program then close any programs you have running Click Next to continue the installation WARNING This program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may result in severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law Cancel Figure 3 1 Installer window Click the Next gt button You
17. parameters for AIST devices Ne Unit name Parameter name OFC servers tag Remarks name 1 Fault ER 2 Powered by a backup source REZP DCMF general Fault signal for all 3 Device AFAS and AFES oe receiving the general Attention signal for all 4 Control and AFES ae 5 Management general Fire signal for all AFES POG_PT of Fire general Start signal for all 6 AFES PUSK_PT T general Fire signal for all AFAS POG_PS APPENDIX A 19 USER S MANUAL Continuation of table A 1 1 List of parameters for AIST devices Ne Unit name Parameter name OBG veh Stag Remarks 8 Alarm loop 1 fault ER_SL1 9 Fire alarm from the loop 1 POG_SL1 10 Alarm loop 2 fault ER_SL2 11 ig Miah Fire alarm from the loop 2 POG_SL2 12 Device Alarm loop 3 fault ER_SL3 13 Fire alarm from the loop 3 POG_SL3 14 Alarm loop 4 fault ER_SL4 15 Fire alarm from the loop 4 POG_SL4 16 Fault ER 17 Powered by a backup source REZP 18 Leakage of the extinguishing UT OTV agent alarm 19 FFD The door to the protected DV O Fire premises is opened Fighti 0 automatics gaung ON 20 Device Mode MODE automatics OFF 21 Attention alarm VNIM 22 Fire alarm POG 23 extinguishing agent fi
18. s faulty 43 The network is BVS_NET_BAD i faulty 14 Interface type BVS_INTERF 15 Error 0 EO 16 Error 1 E1 17 Error 2 E2 18 Error 3 E3 19 Cree Error 4 E4 20 Central panel Error 6 E6 Power Unit 21 Errore Error 7 E7 22 Error 8 E8 23 Error 9 E9 24 Error 10 E10 25 Error 11 E11 26 WCD Error 16 E16 27 Weight Checking Error 17 E17 28 Device Error 18 E18 29 Errors Error 19 E19 30 Error 20 E20 31 Error 21 E21 32 Error 22 E22 33 Error 23 E23 34 Error 24 E24 APPENDIX A 21 USER S MANUAL Continuation of table A 1 2 List of parameters for the control cabinet of IMLDC Ne Parameter type Parameter name OPC server s tag name Remarks 35 Error 25 E25 36 Error 26 E26 37 Error 30 E30 38 Error 31 E31 39 Error 33 E33 40 Error 34 E34 41 Error 35 E35 42 Error 36 E36 1a EE SU I E37 44 Control Device Error 38 E38 45 Errors Error 39 E39 46 Error 40 E40 47 Error 41 E41 48 Error 42 E42 49 Error 43 E43 50 Error 44 E44 51 Error 45 E45 52 Gas gryogen PTR_P_GOS Maximum value 5 11 pressure MPa 53 Error 46 E46 54 Error 47 E47 39 ae erature Error 48 E48 gt Control Device Erora9 E49 57 Pressure and P lt 1 95 MPa PTR_P_LOW Emergency pressure fall 58
19. u item File Exit 6 5 OPC server s functioning description 6 5 1 The main working algorithm of the OPC server When an OPC client addresses the OPC server for the first time via COM infrastructure the server is started automatically Each subsequent OPC client connects to the already started process Therefore an OPC server can handle requests from multiple clients When all OPC clients have disconnected the server is automatically unloaded in 5 seconds The OPC server starts polling a unit only after an OPC client has requested at least one tag from that device While doing this the server creates a special thread for polling devices connected to the given port If a predefined number of attempts to poll the device resulted in failure the device is supposed to be either missing or disconnected If the device answers some of the later polls from the OPC server then the connection with this device is supposed to be restored The value of the field Number of attempts determines the time it takes the server to react to connection breakdown with a certain device The full list of device parameters provided by the OPC server is given in Appendix A BASIC FEATURES AND WORKING PRINCIPLES 17 USER S MANUAL In addition the OPC server provides for each tag a number of standard attributes described below Detailed description of these attributes is given in the OPC Data Access specification version 2 05a
20. will be shown the window with the license agreement presented in figure 3 2 i OPC server for devices AIST and IMLDC Setup License Agreement You must agree with the license agreement below to proceed LICENSE AGREEMENT IMPORTANT READ THIS CAREFULLY This document is the agreement between you individual or entity hereinafter referred to as USER and the Scientific and Production Company KRUG Co Ltd hereinafter referred to as COMPANY ATTENTION BY OPENING THE ENVELOPE WITH THE ELECTRONIC MEDIA CONTAINING THE SOFTWARE AND OR BY USING THE SOFTWARE AS DESCRIBED BELOW YOU INDICATE THAT YOU ACCEPT THE TERMS OF THIS AGREEMENT IF YOU DON T ACCEPT THEM PLEASE RETURN THE UNOPENED ENVELOPE ALONG WITH THE CONTENTS OF THE BOX TO THE SUPPLIER WITHIN 10 DAYS FROM THE DATE OF RECEIPT AND THE MAALILI AP THE CAPT AME Seth M i do not accept the license agreement Figure 3 2 License agreement INSTALLATION OF THE OPC SERVER 5 USER S MANUAL To continue the installation you must accept the license agreement In order to do this you should set the radio button to the item I accept the terms of the license agreement To exit the program please click the Cancel button To continue installation please click the Next gt button You will be shown the window presented in figure 3 3 i OPC server for devices AIST and IMLDC Setup Destination Folder Select a folder where th
Download Pdf Manuals
Related Search