Home
Mode d`emploi - Gamme Première - V101 User Manual
Contents
1. Mode d emploi Gamme Premiere VIOI User Manual Premi re Range VIOI Gebrauchsanweisung Reihe Premi re VIOI Modo de empleo Gamma Premi re VIOI WELCOME TO THE WORLD OF EUROCAVE Our biding desire is to accompany your enthusiasm for wine throughout the years To do so EuroCave puts all of its know how into action to bring together the 6 essential factors in optimal wine maturing Temperature The two worst enemies of your wine are extreme temperatures and sudden fluctuations in temperature A constant temperature of 10 to 14 C 50 to 57 F is considered to be ideal for your wine to reach its apogee Humidity This is an essential factor enabling corks to retain their sealing qualities The humidity rate must be higher than 50 ideally between 60 and 75 Darkness Light and more especially its ultra violet component will rapidly prove noxious to your wine by irreversible oxidation of its tannins For this reason we strongly advise that wines be stored in the dark far from U V light Lack of vibration Vibration disturbs the slow process of your wine s biochemical evolution and is often fatal for the finest wines Storage Moving bottles too often is harmful to wine preservation Having the right type of storage which restricts undue handling is essential Natural aeration A constant supply of filtered air from the exterior is indispensable in order to avoid the development of unpleasant odours a
2. Recycling A caring gesture Electrical and electronic equipment have potentially hazardous effects on the environment and public health due to the presence of noxious substances You should therefore never trash electrical or electronic equipment along with unsorted municipal waste When buying a new EuroCave product Wine cabinet cellar conditioner Vin au Verre you can entrust the recycling of your old appliance to your EuroCave dealer Speak to your EuroCave dealer he will explain all the collection and disposal resources that have been set up within the EuroCave network In compliance with the legal provisions covering respect and care for the environment your wine cabinets does not contain CFC Power saving Install your cabinet in an appropriate place see page 7 and within the recommended temperature range Keep the door open for as short a time as possible Ensure that the door seal is in good condition and not damaged If it is damaged contact your EuroCave dealer N B When replacing your wine cabinet condemn the lock so that children cannot accidentally shut themselves inside Place unusable appliances out of use by unplugging them and by cutting the power lead 5 INSTALLING YOUR WINE CABINET Generalities When your appliance is delivered ensure after unpacking that your cabinet shows no exterior appearance defects impacts buckling etc Open the door and check the integrity of the inside of y
3. LESHOOTING 110 TECHNICAL SPECIFICATIONS Il LAYOUT SIMULATIONS p 6 p 6 p 6 p 9 p 9 p 9 p 10 10 10 1 1 D HH V y N p 21 22 DESCRIPTION OF YOUR WINE CABINET I Cabinet body Hinge Door with lock 2 Universal matted Sliding shelf ABCU EH Storage shelf Temperature sensor location Identification label 2 adjustable feet for levelling Free breather hole Breather hole active carbon filter Control panel Grid Lock receiver um YN 2 IMPORTANT SAFETY RECOMMENDATIONS Warning When using your wine Never use your wine cabinet for anything other than its specific purpose as described in this guide cabinet you should Never unplug the cabinet by pulling on the supply lead Take a firm hold on the plug and pull out smoothly in a straight line from always observe certain the wall socket basic precautions Never use a split power lead or one showing signs of wear along the length A damaged lead should be changed immediately Do not allow children to climb sit stand on or hang from the cabinet shelves They could damage your wine cabinets as well as badly hurting themselves Make sure that you keep the keys always out of the reach of children so there is no risk of them locking themselves in especially N B For optimal safety the cabinet is equipped with a two movement lock To open or close the door you must first push and maintai
4. OUR WINE CABINET Ill Description of control panel Temperature display On Off button Adjustment buttons V Confirmation boutton IV Temperature setting Setting the temperature of your wine cabinet is carried out on the control panel inside Temperature display Displays the current temperature inside your wine cabinet e Adjustment buttons i W set the desired temperature inside the cabinet Confirmation button P confirm the setting temperature On off button U switches the wine cabinet on and off To adjust the temperature of your cabinet e Press and hold down the button for a few seconds The symbol SPI will appear alternatively with the previous temperature setting e Set the desired temperature by pressing the Ma and W buttons Confirm your programming by pressing and holding down the P button for a few seconds Your programming will be automatically confirmed if no button is pressed within the 15 seconds following programming The recommended control range for preserving and maturing your wine is from 48 F to 59 F the default setting is 54 F A To operate correctly your cabinet should be located in a room with a temperature between 32 F and 95 F When there has been a significant modification in set temperatures it can take several hours for your wine cabinet to stabilise and display the desired temperature You have loaded your cabinet with a large number of bottles it ta
5. at something is not functioning correctly notifying your retailer of this possible anomaly is the best way to ensure that your wine cabinet will provide you with long and faithful service 9 OPERATING ANOMALIES In the event of your cabinet not operating correctly please contact your EuroCave wine cabinet retailer If the compressor does not start even though the desired temperature is lower more than 2 C 36 F than room temperature check the wall socket by plugging in any type of electric appliance and make sure that the display is correctly supplied with power see button U on the control panel lf the compressor does not stop place your hand on the condenser metal grid located the length of the rear wall of your appliance Contact your dealer if the condenser is cold If the condenser is hot set the cold temperature as high as possible If the compressor does not stop unplug the cabinet and contact your dealer In the event that the temperature sensor is faulty the symbol EI or El is displayed Where the critical temperature threshold is exceeded for temperatures below 3 C 37 F the display indicates LOI For temperatures above 22 C 71 F the display indicates HII N Use of a glass door can change your wine cabinet s performance in certain extreme temperature conditions Any intervention on the refrigeration unit must be carried out by a qualified refrigeration technician who will check th
6. de Carefully set down your wine cabinet onto its side The side where the flexible cable is attached Remove the screws lower hinge and spacer see Fig B Fit on the opposite side the spacer and the lower hinge using the torx screws see Fig C and position it according to the guidelines Fig D e Stand the cabinet upright Position the door onto the pin of the lower hinge Hold the door against the door seal Place the pin of the upper hinge in the corresponding slot of the door Fit the 3 screws Ensure that the hinge is fixed properly into place if not adjust it See Fig E Fit the 3 grommets Wait 48 hours before plugging in 6 LAYOUT STORAGE Your EuroCave cabinet has been designed to be evolutionary Depending on the model it enables you to adapt it to your needs and evolve in terms of storage Various types of storage Universal slatted sliding shelf Ref ACUP EH Capacity 12 Bottles 13 Bordeaux bottles Universal matted sliding shelf Ref ABCU EH Your wine cabinet s configuration can be modified according to your requirements Refer to pages 21 to 22 for a selection of storage simulations To optimise the layout of your V 10 wine cabinet the sliding shelf n 4 page 5 must be a universal matted sliding shelf ABCU EH I Recommendations on your wine cabinet layout Your EuroCave wine cabinet has been designed to hold a maximum number of bottles in complete safe
7. des erreurs contenues dans le pr sent manuel ni de tout dommage li ou cons cutif la fourniture la performance ou l utilsation de cet appareil La photocopie la reproduction ou la traduction totale ou partielle de ce document sont formellement interdites sans le consentement pr alable et crit de EuroCave WARNING The information in this document is subject to modification without prior notice EuroCave offers no guarantee on this equipment item if it is used for any specific purpose other than that for which it was designed EuroCave cannot be held responsible for any errors in this manual nor for any damage linked to or following the provision performance or use of the equipment item All photocopying reproduction translation wether partial or total are strictly prohibited without prior written consent from EuroCave VW ARNUNG Die Angaben in diesem Dokument k nnen ohne Ank ndigung ge ndert werden EuroCave gew hrt keine Garantie wenn das Ger t anders als f r seine gedachte Zweckbestimmung eingesetzt wird EuroCave haftet nicht f r Fehler die diese Anweisung enthalten k nnte und auch nicht f r Sch den in Zusammenhang oder im Anschluss an die Lieferung Leistung oder Verwendung des Ger tes Das Dokument darf ohne zuvoriges und schriftliches Einvernehmen von EuroCave weder ganz noch teilweise fotokopiert vervielf ltigt oder in andere Sprachen bersetzt werden ADVERTENCIA Las informaciones contenidas e
8. e circuit is waterproof before powering up In the same way any intervention on the electrical circuit must be carried out by a qualified electrician ST 10 TECHNICAL SPECIFICATIONS Height Width Depth Empty weight Usage limits Consumption k Min T F Max T F er 24h kWh VIOI 950 654 689 44 32 95 0 7 24h consomption measured with a solid door and an outside temperature of 25 C 77 F Setting precision 1 C 2 F Display precision 1 C 2 F SIMULATIONS DE RANGEMENT ES STORAGE LAYOUT EXAMPLES LAGERUNGS BEISPIELE SIMULACIONES DE COLOCACI N 22 Temp VFIOI ABCUH 10 AXUH 101 bouteilles 101 bottles 101 Flaschen 101 botellas Les capacit s des armoires sont calcul es en configurations usine avec des bouteilles Bordeaux Tradition The cabinet capacities are calculated in factory configuration using traditional Bordeaux bottles Die Kapazit ten der Schr nke werden mit Bordeauxflaschen Tradition in Fabrik Konfigurationen berechnet Las capacidades de las bodegas est n calculadas en configuraciones de f brica con botellas Burdeos Tradici n AVERTISSEMENT Les informations contenues dans ce document sont sujettes modifications sans pr avis EuroCave n offre aucune garantie sur cet appareil lorsqu il est utilis pour un usage particulier autre que celui pour lequel il a t pr vu EuroCave ne pourra pas tre tenu pour responsable
9. it fluids can settle gently tip cabinet backwards in order to adjust the front feet by unscrewing or tightening so as to achieve a level for your cabinet we recommend the use of a spirit level Remove the protective elements inside your cabinet Position the carbon filter which you will find in the accessories bag placing it inside the cabinet in the breather hole at the top left see adjoining diagram This wine cabinet is designed to be used as a free standing unit only Never connect several wine cabinets to a multi socket N B Whenever moving your cabinet never tip by more than 45 And always on the lateral face on the electrical lead side Did you know A wine cabinet has to be designed so that no bottle comes into contact with the back wall If this were to happen the condensation on the wall could trickle over the shelves and damage the bottle labels Incidentally contact with the cold wall could create a frost point which would be harmful to your wine A 5 INSTALLING YOUR WINE CABINET Il Door reversibility a Parts summary 2 grommets 3 Torx screws 25 4 upper hinge 5 spacer 6 lower hinge b Door reversibility Your wine cabinet door is reversible In this way you can change which way it opens Close the door Remove the grommets see Fig A Remove the torx screws and the upper hinge Lift and take off the door and put it to one si
10. kes several hours for your cabinet to reach the right temperature This could happen when first starting up the cabinet this is not due to an operating fault If however after a few days the problem persists contact your EuroCave or Around Wine dealer N B Only prolonged exposure to excessive temperatures or violent fluctuations in temperature will harm your fine crus e 8 EVERYDAY MAINTENANCE Your EuroCave wine cabinet is a tried and tested easy to use appliance The following few maintenance operations will enable your cabinet to provide you with many years of faithful service Each year you should replace the active carbon filter located in the upper breather hole of your cabinet Manually remove the carbon filter see diagram opposite You can obtain a replacement carbon filter from your usual retailer The replacement part should have an original manufacturer s guarantee Clean and dust the condenser metal grid located the length of the rear wall of the cabinet twice a year When cleaning the back of the cabinet and before moving it make sure it has been disconnected from the mains power supply and that there are no bottles left in the cabinet Once a year completely clean the interior of your cabinet after emptying it and ensuring it disconnected from the power supply use water and a non abrasive cleaning product then rinse carefully Checking the appliance regularly and if you suspect th
11. n este documento estan sujetas a modificaciones sin previo aviso EuroCave ofrece ninguna garant a sobre este aparato cuando se utilice para un uso particular distinto de aquel para el que ha sido previsto EuroCave no podr ser considerado responsable de los errores contenidos en el presente manual ni de cualquier da o asociado o consecuente al suministro las cualidades t cnicas o la utilizaci n de este aparato La fotocopia la reproducci n o la traducci n total o parcial de este documento est n formalmente prohibidas sin el consentimiento previo y por escrito de EuroCave H menm Euro Leader dans le domaine de la conservation la pr sentation et le service des vins depuis plus de 30 ans EuroCave vous propose des solutions adapt es chacun de vos besoins Armoires vins rangements climatiseurs de cave syst me de Vin au verre n h sitez pas contacter votre revendeur EuroCave pour toute information compl mentaire Leader in the wine preservation presentation and service sector for over 30 years EuroCave offers you solutions adapted to every one of your requirements Wine cabinets storage layouts cellar conditioners wine by the glass system don t hesitate to contact your EuroCave or Around Wine dealer for further information Seit mehr als 30 Jahren f hrend im Bereich der Lagerung der Pr sentation und dem Ausschank von Weinen schl gt Ihnen EuroCave L sungen vor die jedem Ihrer Bed rfnisse angepas
12. n pressure while turning the key see diagram DANGER Risk of child entrapment Before you throw away your old wine cabinet Take off the door Leave the shelves in place so that children may not easily climb inside A Never damage your appliance s refrigeration unit 3 ELECTRICAL POWER SUPPLY For your personal safety the wine cabinet must be correctly earthed The wine cabinet power lead is equipped with a standard plug for an earthed wall socket to prevent any risk of electrical shocks Have your mains socket checked by a qualified electrician who can verify correct earthing and if necessary bring your installation into line with Standards Contact your usual EuroCave dealer to change your power lead if it is damaged It must be replaced with a guaranteed manufacturer s part EuroCave lead IMPORTANT any intervention must be made by a qualified electrician Ensure that your socket is correctly earthed and that your installation is protected by a differential circuit breaker 30 mA not valid for some countries A Should you move to another country check if the wine cabinet specifications comply with the country voltage frequency p 4 CARE FOR THE ENVIRONMENT AND POWER SAVING Disposal of packaging The packaging units used by EuroCave are entirely made of recyclable materials After unpacking your cabinet take the packaging to a waste disposal centre For the most part it will be recycled
13. nd mould All of these specific features can be found in the EuroCave VIOI wine cabinet you have bought We thank you for the confidence you have placed in us Usual wine serving temperatures French wines Australian Wines Rhine wine Cabernet franc Beaujolais Cabernet sauvignon Bordeaux Sweet White Chardonnay Bordeaux Dry White Merlot Bordeaux Red Muscat petit grain Burgundy White Burgundy Red Champagne Jura Languedoc Roussillon Provence Ros Savoie Vins de Loire Dry White Vins de Loire Sweet Vins de Loire Red Vins du Rh ne Vins du Sud Ouest Sweet Vins du Sud Ouest Red Pinot noir Sauvignon blanc Semillon Shiraz Verdhelo Other wines Californian Chile Spain Italy CONTENTS DESCRIPTION OF YOUR WINE CABINET PT IMPORTANT SAFETY RECOMMENDATIONS SP e ELECTRICAL POWER SUPPLY Fei e CARE FOR THE ENVIRONMENT AND POWER SAVING LA Is e INSTALLING YOUR WINE CABINET l Generalities Il Door reversibility ES e LAYOUT STORAGE l Various types of storage Il Recommendations on your wine cabinet layout Ill Adding sliding shelves IV Modification to cabinet layout Lal e COMMISSIONING YOUR WINE CABINET l Connection Il Switching on the cabinet Ill Description of control panel IV Temperature setting Oe e EVERYDAY MAINTENANCE lo e TROUB
14. our appliance walls shelves hinges control strip etc In the event of a problem contact your EuroCave dealer Now move your cabinet to its chosen location This location should be open to the exterior to enable air circulation not a closed cupboard etc be removed from any heat source not be too damp laundry room utility bathroom etc have a solid and flat floor have an electrical power supply standard power socket 6A with earth and differential circuit breaker 30 mA not valid for some countries Do not place your cabinet in an area that might be flooded willt Avoid water splashes over all or part of the back of the appliance wll IN IN Place the water recuperation tank on the compressor stand you will find this in the accessories bag in your cabinet ANN Ill ge il sliding it under the little outlet hose from the casing with the deepest part of the tank under the hose cacao HI da Take the power lead which you will find in the accessories bag in your cabinet and connect it to the connector at the bottom left of the cabinet see adjoining diagram Release the power cable so that it is accessible and position your appliance leaving a space of 8 to lOcm between the wall and the rear of your wine cabinet Release the power cable so that it does not enter into contact with any part of the appliance Wait 48 h before plugging in so that the internal circu
15. re tighten the screws Repeat this operation for a second if required Adjustment screw E la Adjustment screw Slider al d e EE Slider ES 6 LAYOUT STORAGE IV Modification to cabinet layout To change the position of a storage shelf first of all completely unload the shelf and move the shelf supports taking care to re attach them as shown opposite Shelf support To change the position of a sliding shelf first of all completely unload the shelf Then lift the sliding shelf and slid it towards you whilst holding the front of it upwards Remove the wall slider guides marking which is right and which is left then reinstall them as shown below Installing the rear section of the guide Then replace the sliding shelf as shown opposite Sliding shelf Guide Installing the front section of the guide Wall E Connection Check that the plug is connected to a power supply presence of correct amp fuses functioning 30 mA differential circuit breaker not applicable to certain countries Make sure you wait 48H before commissioning Il Switching on Press the U button located on the adjustment panel until the display is activated When the adjustment function is starting up the message OD will appear Wait for the temperature to be displayed do not touch any of the control buttons or unplug the appliance during this time 7 COMMISSIONING Y
16. st sind Wein Zigarrenklimaschranke Weinkeller Kompaktklimaanlagen Ger te f r den glasweisen Offenausschank Weinkeller Regalsysteme Zogern Sie nicht l nger setzen Sie sich mit Ihren EuroCave Handler in Verbindung wenn Sie noch irgendwelche Fragen haben L der en el campo de la conservaci n presentaci n y el servicio de vinos desde hace 30 a os EuroCave le propone soluciones adaptadas a cada una de sus necesidades Bodegas estanter as climatizadores de bodegas sistemas de vinos a la copa Para toda informaci n complementaria no dude en contactar a su distribuidor EuroCave 07 2008 100 www eurocave com info eurocave com
17. ty We recommend that you abide by the following suggestions in order to optimise its storage capacity Please distribute your bottles as evenly as possible on the various shelves in your cabinet in order that the weight is distributed over a wider area Also make sure that bottles do not touch the back or the walls of the cabinet Please distribute bottles as evenly as possible over all of the upper area of the wine cabinet try not to put all your bottles either at the top or at the bottom Be sure to follow the storage recommendations according to the type of storage shelves in your cabinet and never pile bottles on top of each other on a sliding shelf If you are equipped with sliding shelves it is preferable to place these at the top of the cabinet for ease of daily access For the same reason place one or two bottles of each of your various wines on the sliding shelves and keep you reserve bottles on the storage shelves You then only have restock the top shelves a you drink a bottle When using your wine cabinet never pull out more than one sliding shelf at a time III Adding sliding shelves When you buy your cabinet the sliding shelves are perfectly adjusted to the interior dimensions of the appliance you have just bought If you buy additional sliding shelves you may need to carry out this adjustment yourself To do this loosen the right or left screw 2 screws on the first slider then set to the width required and
Download Pdf Manuals
Related Search
Related Contents
Mode d`emploi nomenclature VQR3-10 On-board unit user manuals Onduleur/chargeur Conext™ SW Onkyo TXSR307 User's Manual 1 - Toshiba Users manual online payments and reservation Laundry SGNK 1 - enrdd.com Copyright © All rights reserved.
Failed to retrieve file