RGBW LED beam movinghead User manual - Bax
Contents
1. DMX control mode Select a DMX starting address and a DMX channel mode to operate this fixture with a DMX controller The fixture either uses 13 or 29 channels depending on the settings you have chosen E im 4 N ME i 3 Jemen m jm gt i si Us 6 Cluster 4 White dimmer White 0 100 0 255 Installation and maintenance Mounting the bracket On the bottom of the movinghead there are two holes to mount the included bracket using the included bolts It is possible to mount a G clamp or halfcoupler to this bracket It is also possible to mount the bracket on a ceiling wall bar floor desk or any flat surface Use proper equipment to install this fixture as a dropping fixture may cause severe injury Ayra is not responsible for any damage or injuries caused by improper installation Cleaning Make sure to clean the exterior of the unit frequently as the build up of dust and dirt may have negative effects on the cooling and optics of the fixture The exterior plastic parts of the unit can be cleaned with a damp cloth The optics of the fixture can be cleaned with a clean cloth or paper towel with the addition of a non aggressive glass cleaning solution Clean the fan outlet and the cooling vents with a small brush while using vacuum cleaner suction to remove any loose dust and or dirt Clean the exterior of this fixture once a month When using this fixture intensively the frequency of maintenance needs to be2. mode The status of the movinghead is shown on the display which automatically shuts off after a few seconds of inactivity The shown values determine the current status and can be changed by pressing the buttons on the control panel The four buttons each have their own function for easy navigation Press the MODE ESC button to switch modes so you can easily C C C select the built in automatic music controlled or DMX mode MODE ESC UP DOWN ENTER To adjust settings or to read certain values the display will show several codes An explanation for each code can be found below EE 000 18000 RGBW full on intensity When using several fixtures in master slave mode please note that only the first fixture can be set to master settings The other fixtures will respond as slaves which will mimic the movement intensity and colours of the first fixture Working modes The ERO Minibeam 12 movinghead is equipped with several working modes Sound active mode The fixture will react to music with an internal microphone The microphone sensitivity is digitally adjustable with the LCD display and menu buttons Auto mode The fixture will run through different colours and the built in programs The programs and colours are adjustable with the LCD display and menu buttons Slave mode The unit will run as slave fixture thus mimicking the master fixture XLR XLR cables are required for this function not included
3. FIRER ERO INNGERN le RGBW LED beam movinghead User manual Safety precautions WARNING This unit may cause serious injury to the eyes when used incorrectly It is therefore strongly advised to read this user manual carefully to get familiance yourself with the functions of this device WARNING This unit must be operated by or under the supervision of an adult This device is not suitable for children WARNING Do not look directly into the beam from a short distance This may cause serious injury to the eyes Ayra is not responsible for any injuries caused by incorrect use of this device Installation requirements Always check the power supply to which you want to connect the device If the voltage requirements do not meet do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Only use the included mounting bracket if you want to position the unit against a ceiling or truss system When installed in a hanging position above your audience this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device The unit is designed to be installed with a halfcoupler or G clamp by using the included mounting brackets Direct installation with proper bolts is also possible Make sure there are no flammable objects in the direct environment of the device Do not block the beam exit and
4. bined in auto mode Connectors DMX 3p XLR male and female Power IEC power connector Included accessories Power cable with Shucko amp IEC connectors Mounting bracket Product manual revision 03 09 2013 10
5. fan Keep a minimum distance of 0 25 meter from any walls to provide sufficient cooling Make sure the beam exit and fan are not blocked by any objects in the near environment Always use the included power supply Contact your local dealer for a replacement unit if necessary Maintenance and protection Keep the unit away from dusty envronments as this may have negative effects on the fan cooling system and optics Clean the optics and fan with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Always disconnect the unit from the power supply when cleaning the unit Reconnect the unit only when any moist on the fixture has evaporated completely Do not switch the power on and off frequently as this may cause serious damage to the unit Avoid heaw shocks and collision during transport and use as this may cause damage to the LED light source electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage Box contents Box contents 1x ERO Minibeam 12 1x power cable 1x installing bracket 1x small bag with mounting hardware Unit and accessory inspection A
6. increased Transport When using this fixture in mobile setups provide sufficient protection during transport Use the original packaging of this unit or use a professional flightcase with proper foam inlay This way the electronics optics and housing are protected against severe shocks exterior damage and failing electronics Make sure the moving parts of the movinghead pan and tilt motors are secured during transport Shocks and fierce movement of the pan and tilt stepping motors may cause permanent damage After use let the unit cool down for at least 10 minutes When using DMX use the black out option on your DMX controller This way the unit is positioned in a static stand by mode and the internal fan is able to cool down the internal electronics which decreases the chance of damage during transport Replacing the internal fuse First check whether a failing power supply may be the cause of malfunction When you suspect that the internal fuse is broken the fuse can be replaced by removing the fuse cover located directly below the power inlet WARNING Before changing the fuse always disconnect the fixture from your wall outlet or any other power supply to prevent electric shocks Always replace a broken fuse with a fuse that has the same type and rating After the fuse has been replaced always close the fuse cover Reconnect the fixture to your power supply and check whether the problem is solved When this does not solve yo
7. l specifications high power LED beam movinghead light source 12x RGBW 10 Watt LED module CREE branded LED light source expected LED lifespan 100 000 hours RGBW colour mixing for fluent color changes control over four seperate LED segments for creative lighting applications and unique chase effects high precision stepping motors with smooth 16 bit movement movement speed adjustable for pan and tilt wide movement range 540 pan 180 tilt 0 100 dimmer for each colour master dimmer narrow beam angle 8 large graphic LCD display with menu buttons for easy access to several parameters and settings display flip function for easy menu operation in hanging position working voltage 90 250V AC 50 60 Hz power 120W max weight 5 kg Working modes Sound active mode with internal microphone digital sensitivity adjustment Auto mode with eight internal customizable programs Master slave mode DMX mode DMX control 13 or 29 DMX channels dimmer function for each colour master dimmer dimmer function for each colour in each segment master dimmer only in 29 channel mode strobe mode 0 30 Hz pan and tilt control pan fine and tilt fine control RGBW master control 0 100 for each colour pan tilt soeed adjustment combined auto run select different internal chases with certain DMX values auto run speed variable speed for pan andt tilt com
8. lways use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it If the unit is not going to be used for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any light do not look directly into the lens When the fixture suddenly produces a beam it may cause injury to your eyes Device overview Beam output Control panel with display and menu functions On off switch Fan IEC power inlet DMX input DMX output 1 2 3 4 5 6 7 Setting up the unit To activate the unit connect the included power supply to the unit and a suitable 230V 50 Hz power outlet Switch the on off switch to the ON position the LED movinghead will activate Give the movinghead time to calibrate the stepping motors which are used to determine the position of the head You may hear and see some shaking which is normal The stepping motors use an end point to determine the beginning and end of their movement After calibration the movinghead will start the previously used mode but by default it is set to DMX
9. ur problem contact your local dealer for help IMPORTANT A spare fuse is located inside a special compartiment of the fuse holder Spare parts This unit has no user serviceable parts inside When any damage to internal components occurs contact your local dealer or a specialized technician in order to repair the fixture Checkup To prevent dangerous situations make sure your fixture is in optimal condition before using it Check your fixture frequently by using the following checklist All screws must be mounted tightly Check all screws and metal parts for corrosion No visible corrosion may be present The exterior of your fixture must be in optimal condition Check your fixture for dents cracks or missing parts Your installation spot must be in optimal condition Check your installation spot for corrosion cracks dents and strength Electrical components connectors and cables must be in optimal condition Any form of damage cuts exposed wire cores or any other visual deformities should not be present If any visual or mechanical damage is detected contact your local dealer or a specialized technician Do not use a damaged or failing fixture Connectors and wiring schematics DMX connections Electrical wiring EUA AUAI eine nee Cable International XLR mounting socket XLR mounting plug rown 1 Ground 1 Ground 2 Signal 2 Signal i Yellow Green 3 Signal 3 Signal i Technica
Download Pdf Manuals
Related Search