MAGNETIC DOOR CONTACT
Contents
1. Battery type CR2032 3V Lithium Number of batteries 1 Battery operation time 18 months Radio transmitter receiver frequency 868 Mhz Range of Operating Temperatures 20 455 C Door contact dimensions 60x37x18mm Magnet dimensions 60x17x16mm Radio communication range 30 meters in premises 150 meters in open areas Compatible with security systems ELDES Wireless This operation time might vary in difference conditions Changing the battery Only CR2032 3V Lithium batteries should be used Install only new good quality and not expired batteries In order to replace old battery with a new one remove front cover of the magnetic door contact see chapter 1 carefully remove the device PCB and remove old battery Then insert the new CR2032 3V Lithium battery ATTENTION The battery must be removed if device is not in use ATTENTION In order to avoid fire or explosion hazards the system must be used only with approved battery Special care must be taken when connecting positive and negative battery terminals Dispose old batteries only into special collection sites Do not charge disassemble heat or incinerate old batteries USER MANUAL EWD1 V1 0 3 MAGNET FRONT SIDE BACK SIDE 1 BATTERY 2 LED 3 PANIC button 4 RESET button 5 PINS for firmware updates 6 TAMPER Fig No 4 Restoring default parameters 1 Remove the battery 2 Press and hold RESET button 3 Add removed b2. B Warranty period starts from the day the system has been purchased by the end user The warranty is valid only if the system has been used as intended following all guidelines listed in the manual and within specified operating conditions Receipt must be kept as a proof of purchase date The warranty is voided if the system has been exposed to mechanical impact chemicals high humidity fluids corrosive and hazardous environment or other force majeure factors Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around Don t use the system where it can be interfere with other devices and cause any potential danger Don t use the system with medical devices Don t use the system in hazardous environment Don t expose the system to high humidity chemical environment or mechanical impacts Don t attempt to personally repair the system Any system repairs must be done only by qualified safety aware personnel the product must not be disposed of together with household waste To prevent possible harm to human health and or the environment the product must be disposed on in an approved and environmentally safe recycling process For further infor ga Mation on how to dispose of this product correctly contact the system supplier or the local authority responsible for waste disposal in your area x The WEEE Waste Electrical and Electronic Equipment marking on
3. attery 4 Hold RESET button till LED indicator starts fast several times blinking 3 Configuration using software ELDES Configuration Tool Software ELDES Configuration Tool is used to work directly with central device of the security system which can be connected to the computer via USB port This software simplifies system configuration process by allowing to use PC in the process Using this software user can 1 To bind new magnetic door contacts EWD1 to central monitoring station 2 To remove or replace old magnetic door contacts with new ones 3 To configure settings of all added to the system magnetic door contact 4 To configure security system settings Software ELDES Configuration Tool is a freeware and can be downloaded from website www eldes lt 4 Configuration command SMS Messages ATTENTION send command SMS messages to the number used by the central device of the security system All SMS messages should start with the main 4 digit user password in the examples provided XXXX marking is used Underscore symbol _ is used to represent space symbol 4 1 Binding Modules to the Security System ATTENTION before sending SMS message check whether magnetic door contact EWD1 has the battery inserted If it hasn t binding to the central security system will be unsuccessful Binding of magnetic door contact EWD1 to the central device of security system station is performed by indicating module ide
4. c door contact EWD1 To change an old magnetic door contact EWD1 with a new one send the following SMS message XXXX_REP ID lt ID5 Here instead of ID indicate identification number ID of the old magnetic door contact EWD1 Identifi cation number of the new magnetic door contact EWD1 is indicated instead of ID5 marking The new magnetic door contact is provided with the same zone number with all previous settings valid for the old one 4 6 Deleting magnetic door contact EWD1 To delete magnetic door contact EWD1 from the security system send the following SMS message 1111 del 07000022 XXXX_DEL ID Here instead of ID indicate identification number ID of the magnetic door contact EWD1 want to dele te Removed from the system zones can be used to connect other wireless devices 5 Additional Information Limited Liability The buyer must agree that the system will reduce the risk of fire theft burglary or other dangers but does not guarantee against such events ELDES UAB will not take any responsibility regarding personal or property or revenue loss while using the system ELDES UAB liability according to local laws does not exceed value of the purchased system ELDES UAB is not affiliated with any of the cellular providers therefore is not responsible for the quality of cellular service Manufacturer Warranty The system carries a 24 month warranty by the manufacturer ELDES UA
5. eldes e 1 MAGNETIC DOOR CONTACT EWD1 Magnetic door contact with panic button EWD1 is a wireless device with magnetic contact which are used to secure doors windows or any other opening parts and operating with ELDES wireless security systems Users have to bind it to the central device of secu rity system by sending a corresponding command via SMS message or using software ELDES Configuration Tool When EWD1 is connected to the system two wireless zones are added First wireless zone is used to monitor the magnetic contacts and the second wireless zone is for managing the panic button By default panic button zone is configured as Silent zone and in case of violation system will cause an alarm to administrator numbers or and to monitoring station without turning the siren on It is possible to connect up to 16 wireless devices to the central security system at a time Maximum distance for wireless connection is 150 meters in open areas 1 Device Installation 1 Open EWD1 case and insert the battery o o S Fig No 1 oo 2 Magnetic door contact consists of two parts a magnet and a sensor Sensor components are a mounting part and the sensor Magnet components are a mounting part and the cover 2 1 Fix the sensor mounting part with two screws on the door or window jamb 2 2 Fix the magnet mounting part with two screws next to the sensor mounting part on door or window frame How to fix the ma
6. enabled or disabled By initial factory default parameters all activated zones are enabled Any zone can be enabled by sending SMS message with the following format XXXX_Z1 0ON Z2 0N Z3 0N Any secured zone can be disabled by sending SMS message with the following format XXXX_Z1 OFF 22 OFF 23 0FF an Indicate as many zones as you want to change their statuses separating entries by symbol as shown in the examples provided 4 3 Requesting system status information To find out the alarm texts and statuses of activated zones send the following SMS message XXXX_STATUS You will receive system response via SMS message for example Z1 ON OFF Zone1 Z2 ON OFF Zone2 C1 ON OFF Controller1 C2 ON OFF Controller2 This information SMS message indicates all wireless ELDES devices connected to the system and their current parameters ATTENTION System informs about all active zones If there are many active zones the system informs about all of them in several SMS messages 4 4 Requesting number of available slots to connect wireless devices To find out the number of available slots to connect wireless devices to the central device of security system send the following SMS message XXXX_STATUS_FREE NOTE maximum number of wireless devices that can be connected to the central device of the security system station is 16 units USER MANUAL EWD1 V1 0 5 4 5 Changing magneti
7. gnetic door contact correctly see Fig No 2 The distance between the magnet and the door contact must be no larger than 20 mm 0 0 MAX 20 mm gt i O ie Fig No 2 2 3 The sensor should be attached to the fixed sensors mounting part When attaching sensor pay attention to the tamper micro switch it must be pressed 2 4 The magnet cover should be attached to the fixed magnet mounting part NOTE it is not recommend to fix the magnetic door contact other ways than with screws e g with duck tape The incorrect ways of fixing magnetic door contact see Fig No 2 Fig No 3 3 Bind the device to central monitoring station Use a software ELDES Configuration Tool or send corresponding SMS messages Please read software Help section or central system installation manual for more information Software ELDES Configuration Tool and installation manual can be downloaded for free in website www eldes lt The system automatically informs about su ccessful unsuccessful bound device If attempt to bind is unsuccessful try to move the door contact EWD1 closer to central monitoring station and bind anew 4 EWD1 magnetic door contact is ready to use 2 Technical Specifications Package content 1 EWD1 door CONA Cassimin tye 1 De MaQTe A PREIEI RE AEI AAE ENRE te I 3 CR2032 3V Lithium battery 4 User manual y 1 y 1 5 Screws y 4 Electrical and Mechanical Characteristics
8. ntification numbers XXXX_SET ID1 Here ID1 means magnetic door contact identification number This identification number can be found on the back of the device The system automatically provides two security zones to the connected door contact The system informs about this via SMS messa ge for example ID1 Z14 ID1Z15 here instead of ID1 will be identification number of the module that you want to connect Z14 and Z15 the numbers of free zones provided by the system nn You can bind more than one magnetic door contact at a time In such a case separate identification numbers by symbol for exam ple XXXX SET ID1 1D2 D16 4 2 Settings of Activated Zones After activating magnetic door contacts EWD1 each of them is automatically given zones numbers and set to the default settings 4 2 1 Adjusting Alarm Text Alarm text of a particular zone is adjusted by sending the following SMS message XXXX_Z2 TEXT Here instead of Text enter the required alarm text consisting of up to 24 characters and instead of Z2 indicate the number of the corresponding zone You receive this alarm text by SMS message when a corresponding zone is triggered To change alarm text of more than one zone separate entries by symbol for example XXXX Z2 Text2 Z3 Text3 4 2 2 Enabling Disabling Zones You can choose which zones after activating the alarm in the whole system will be
9. this product see right or its documentation indicates that Copyright ELDES UAB 2010 All rights reserved It is not allowed to copy and distribute information in this document or pass to a third party without advanced writ ten authorization by ELDES UAB ELSDES UAB reserves the right to update or modify this document and or re lated products without a warning Hereby ELDES UAB declares that this EWD1 magnetic door contact is in com pliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www eldes It ce USER MANUAL EWD1 V1 0 7
Download Pdf Manuals
Related Search