Look, Listen & Live
Contents
1. to 2 0 YOUR RECEIVER 2 1 PIN code default 0000 _ 2 2 2 Front panel KA iy 16 Fig 1 1 Standby on button To turn the unit ON or to standby mode KC 2 Channel up down To change channels without using the remote S control 3 Volume up down To change volume without using the remote control 4 Remote control sensor Receives the signal from the remote control 5 Standby indicator Shows power state of the receiver Green LED receiver is tumed on Red LED receiver is in standby mode 6 LED display Shows channel number in operation and time in Standby 7 USB For connection of extemal storage devices 2 3 Rear panel Fig 2 1 SAT IN To connect to the LNB of your satellite dish for reception of satellite broadcast signal 2 SAT OUT To loop through the satellite signal to a second receiver 3 S PDIF To connect to a digital or home cinema audio amplifier 4 HDMI To connect to the HDMI input of your TV using a good guality HDMI cable 5 TV SCART To connect to TV using a SCART cable 6 DVD VCR SCART To connect to a Video or DVD recorder 7 Power cord The receiver requires a mains voltage of 100 240V AC 50 60Hz auto selecting Please check the local power conditions before connecting the receiver to the mains Supply 2 4 Remote Control Fig 3 1 0 Turns the receiver ON standby 2 To turn the sound on or off 3 RED Alphabetic search of channels in channel list mode several functions in the OSD menu and Teletex2. THS220 Digital High Definition Satellite Receiver User manual Bedienungsanleitung Manuel d utilisation Manuale d uso PyKoBOACTBO MONBSOBATENA Look Listen amp Live www thomsonstb net tel NI OO OT m OONKWO o e Fig 6 Satellite Ry Dish amp Ki TV SCART DVD VCR SCART Fig 7 Satellite Dish Ko OTA Ho SATELUTE REGEER THS220 TV SCART DVD VCR SCART Satellite Dish Fig 8 Coaxial cable Coaxial cable TV SCART DVD VCR SCART TABLE OF CONTENTS 1 0 INSTRUCTION 1 1 Safety Instructions 1 2 Storage 1 3 Equipment Set up 1 4 Accessories 1 5 Usage of external USB devices 2 0 YOUR RECEIVER 2 1 PIN code default 0000 2 2 Front panel 2 3 Rear panel 2 4 Remote Control 2 5 Installing the Batteries 2 6 Using the remote control 3 0 CONNECTIONS 3 1 Basic connection using a Scart cable 8 2 Basic connection using an HDMI cable 3 3 Connecting multiple fixed LNBs using a DISEGC 1 0 switch 4 0 FIRST TIME INSTALLATION 4 nstallation 5 0 QUICK GUIDE FOR USING YOUR RECEIVER 6 0 OPERATION 6 1 Changing channels 6 2 Info Banner 6 3 Selection of audio language
3. 6 4 Teletext 6 5 Subtitles 6 6 Changing the Aspect Ratio 6 7 Changing the resolution 6 8 EPG Electronic Programme Guide 6 9 Favourite channels 6 10 Changing between DTV VCR contents 7 0 MAIN MENU 7 1 Programme 7 2 Picture 7 3 Channel Search 7 4 Time and Date Settings 7 5 Option 7 6 System Settings 7 7 USB 2 8 0 TROUBLESHOOTING 23 9 0 SPECIFICATIONS 24 69 ago wy oO CO SN ob OOD a OOOOOOOOOO THOMSON declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004 108 EC and 73 23EEC RoHS 2002 95 EC Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change All product names are trademarks or registered trademarks of their respective owners 03 Ju 2013 14 47 THOMSON 2012 All rights reserved P1 P OV Six P2 1 0 INSTRUCTION O G amp 1 1 Safety Instructions 4 2 DO NOT INSTALL YOUR RECEIVER Ko Ina closed or poorly ventilated cabinet directly on top of or under any other KA equipment on a surface which might obstruct the ventilation slots KS 4 DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES To direct sunlight or any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage t
4. Follow the instructions displayed on screen The update process will ake some time Once the update has been completed the receiver will display Software Upgrade Complete Please Restart Unplug the receiver from the mains and plug it in again Your updated receiver will start with the last shown channel WARNING NEVER power off the receiver or remove the USB device during the software update process Doing so might cause irreparable damage to your receiver and will void your warranty Auto Standby Auto standby is a new power saving feature that helps you reduce power consumption It will switch off the receiver when no command is given for a defined period of time It is set per default to 180 minutes With the lt P buttons you can choose between different time intervals or Off for disabling the feature In the 0000 mode you can enter the desired auto standby time by using the 0 9 buttons NOTE If there are timers running the auto standby function will be disabled for the booked time 7 7 USB Press MENU and select USB The menu provides Multimedia features to playback Music Photo and Movie The different supported file formats are listed below In this menu you can also see information about the total and free space of the connected USB device make video and photo configurations and format the USB device into a format accepted by the receiver The unit supports USB devices with FAT and FAT32 format Make sure your U
5. if available for the ight LNB Motor using a motor use lt P to select between DISEgC1 2 or GOTOX depending on the motor type you use Then Press OK to show the menu to set the position or GREEN or location MAIN MENU KA DiSEgC1 2 love the motor to the right position for locking the signal ike explained below gt D Move Continue press lt P for moving West East It will keep movinckas ong as the button is hold pressed Pressing once moves in 1 step Move Step 1 press lt P for moving West East in 0 3 step Store Position o store the current motor position for the selected satellite lt Goto Reference o go to the reference 0 position 6 DISEgC1 3 Select DiSEgC1 3 with the lt P buttons Press GREEN O setup your location coordinates A pop up window will appear in which the following settings can be made Location Use lt P to select one of the pre set locations Choose a ocation nearest to you If you know the coordinates of your place of residence you can choose Manual and make the ollowing extra adjustments Longitude Direction Choose East or West Longitude Angle Use the NUMERIC buttons to enter the coordinate Lattitude Direction Choose North or South Latitude Angle Use the NUMERIC buttons to enter the coordinate Once all setting are made press EXIT to save the data and leave the window Now press OK to enter the DiSEgC1 3 menu Move Auto
6. start 7 3 5 Scanning by transponder Manual Scan Press GOTO for displaying the When using a multi feed antenna with more than Um ht Q K channels will be stored and the receiveFyill switch he satellites your antenna is adjusted to wit e tton The selected satellites will be marked by the Set the LNB inputs in the DiSEqC point and press D he settings like explained in 4 press OK or BLUE again to ulti Scan on all selected satellites ed After configuring transponder list of the highlighted satellite By pressing GOTO again you switch back to the satellites list Single Transponder Scan Use the A V buttons to highlight the transponder Multi Transponder Scan 7 3 6 Satellite Edit options Add satellites Satellite Name Edit satellites Delete satellite P16 you want to scan Press BLUE for Scan A window with scanning settings will be displayed After configuring the settings explained in 7 3 1 3 above press OK or BLUE again to start scanning the highlighted transponder When the scan process has been completed all found channels will be stored and the receiver will switch to the first found channel Select the transponders you want to scan with the OK button The selected transponders will be marked with the symbol Press BLUE for Scan A window with scan settings will be displayed After configuring the settings like explained in 7 3 1 2 above press OK or BLUE aga
7. RED in the channel list An alphabet banner will now be displayed Use AV to select the first letter or letters of the channel and OK to confirm All channels beginning with the chosen letter s will now be displayed Close the 4 Ze alphabet banner by moving the highlight to OK Now press OK and select the 4 channel in the filtered list The following buttons are available in the channel list and viewing mode RED Opens an alphabet banner for guickly finding a channel TV RADIO Toggles between TV and radio channels GOTO Opens the Satellite List for satellite selection In viewing mode FAV To switch to one of the available favourite lists 6 1 3 Using the AV buttons A will switch to a higher channel V will switch a lower channel 6 1 4 Using the RECALL button SSS Use the RECALL button for switching between the last viewed channels Please refer to section 7 6 for more details 6 2 Info Banner At any time during viewing mode you can press the button to get information about the current channel as well as the current and following programme Press i twice to view detailed info on the current and following programmes and technical details about the current channel Press again or EXIT to close the information You can change the on screen duration of the info banner in the Option menu Please refer to section 7 5 for more details Programme information is displayed when available Availability de
8. has the possibility to loop through the signal from the VCR SCART input to the TV SCART This allows you to watch content from the connected DVD or VCR recorder via the receiver P10 OPERATION i 4 Switching between DTV VCR modes in operation mode is realized by sing the DTV VER button AV IN will be displayed on the front LED when receiver js in VCR mode Press the DTV VCR button again to return to the digital TV content Please refer to Loop Through point in section 7 2 for more details K 7 0 MAIN MENU O Es 7 1 Programme Press MENU and select Programme using the lt P buttons Press OK or the V button to enter the Programme submenu Press OK or the button to edit programme settings Press EXIT to exit the menu 7 1 1 Programme Edit To edit your programme preferences lock skip favourite move or delete please go to the Programme Edit menu This menu requires a password upon access Enter your password or use the default password 0000 if you did not change it Use AV lt P to highlight a channel TV RADIO to toggle between TV and radio channel lists and GOTO to select a satellite if more than one available Set favourite programme Your receiver allows you to store channels in up to 4 favourite lists Due to the large number of channels available on satellite nowadays this can be a very useful function 1 Highlight the preferred programme then press the FAV b
9. the GREEN button to edit an existing booking Press the BLUE button to delete a booking from the Press OK to confirm deleting or EXIT to cancel it he ist You can set timers for programmes directly from the EPG Please Press MENU and select Option In this menu you can adjust the OSD Language Subtitle Language Audio Language Digital Audio mode and Banner Time Select an option and press lt gt to adjust the setting Press EXIT to exit the menu OSD Language Select the language for the On Screen Display Subtitle Language Select subtitle language Audio Language Select audio language for watching TV channels If the language is not available the default programme language will be used Digital Audio Select the digital audio output mode Settings affect both S PDIF and HDMI outputs PCM audio from any format will be converted to PCM format RAW audio from receiver will be send in original format RAW HDMI On As RAW but also affects the HDMI output OFF digital audio output disabled Banner Time Set the time out for the info banner Possible settings are 1 10 seconds P18 MAIN MENU Sy 7 6 System Settings 23 Press MENU and select System In this menu you can adjust the systerfagtings Press AV to select an option and press lt P to adjust the setting Press EXIT to exit the menu a KC Set Password Set or change the password for locked programmes and menu access Enter your o
10. SB device is correctly formatted NOTE THOMSON cannot guarantee compatibility operation and or bus power with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit P20 MAIN MENU With large amounts of data it may take longer of a USB device Some USB devices may not be properly recognized supported format some files may not play or display depending on the conte 3 7 7 1 Multimedia or the system to read tg contents Ki Even when they are i If there is no USB device plugged in a waming message No USB Device is KA Found will be displayed When a USB device is detected you can choose KA between Music Photo and Movie in this menu Select one of them press OK to enter the file browser and select the file you wish to be played Music supported file formats are MP3 and WMA Photo supported file formats are JPG and BMP Movie supported video files in various formats MPG MPEG TS VOB MP4 AVI Music Select a music file and press OK to start playback During playback following functions are available gt or OK Start playback of the selected file IL To pause resume playback and W to stop it KA A To rewind or forward playback in x2 x4 x8 x16 and x32 speed When it has fast rewinded to the beginning playback of the current file will be resumed When it has fast forwarded to the
11. SD menu disappears 7 4 Time and Date Settings Press MENU and select Time In this menu you can adjust the time and date settings Press AV to select an option and lt P to adjust the setting Press EXIT to exit the menu P17 MAIN MENU Eml kaf Q a Time Auto Select On for automatic time and date update jrom live signal or Off for entering them manually D Time Zone Select the Offset from GMT standard time Summer Time Select On or Off depending on the year s period By Date Enter the date when Time Auto is set to Off ey Time Enter the time when Time Auto is set to Off D 7 4 1 Timer Schedule Ki In this menu you can setup the schedule for automatic switchi channels at a particular dai Add Press select bui firs When you have entered Edit Delete NOTE e time The timer menu can be en viewing mode by pressing the BLUE button RED to add a new booking In ng to defined ered directly from he appearing dialog channel type and number start refer to section 6 8 for more details 7 5 Option ing date and time end time repeat cycle once daily or weekly for selecting he channel number you can use the lt P or numeric ttons but also the fast channel Find option RED allows you to enter the channel number by selecting letters of the channel s name in the pop up window all parameters press OK to store your booking Press
12. arantee the playback of video files although extensions are listed here as it depends on codec used data bit rate and resolution Connectors SAT IN SAT OUT HDMI V A Output Type A Version 1 0 TV SCART RGB CVBS Audio L R output with volume control DVD VCR SCART CVBS Audio L R S PDIF Dolby Digital Out Coaxial USB 2 0 Type A Connector P25 SPECIFICATIONS TC Af Af General Data Input voltage range 100 240 V AC 50 60 Hz b Power consumption max 18 W typ 6 W Ki Power consumption in standby max 1 00 W ZS Operating temperature O 40 C KA Storage temperature 10 50 C 2 Operating humidity range 10 85 RH Non condensing KA Size W x D x H in mm 224 x 164 x 44 KA Weight 0 63 kg P26 SPECIFICATIONS
13. ches to the next previous channel in viewing mode switches to the next previous page in the channel list or moving the highlight up down in the menu Viewing mode displays the channel list Menu activation of the highlighted item Decreases increases the volume level in viewing mode navigating through the menus changing values of settings in a menu Viewing mode displays the EPG Electronic Programme Guide Press once to display channel number name and current next info Press twice to display detailed event info and transponder signal strength information Press again back to viewing mode Increases decreases the volume level in TV mode To access your favourite channels Toggles between available favourite groups PS YOUR RECEIVER TC Af Af Ki 28 GOTO In playback mode opens the time bafjer for selecting the moment where to jump to 29 P Switches to the previous next programme D TV mode 30 DTV VCR Switches to VCR input if the receiver is in DTV ey state Switches to DTV if it is in VCR state KI 31 0 9 Channel number and numeric value input KA 32 TV RADIO Toggles between TV and radio mode 10 2 5 Installing the Batteries Fig 4 Remove the battery cover from the remote control and put 2x AAA size batteries inside the compartment The diagram inside the battery compartment shows the correct way to install the batteries 1 Open the cover 2 Install batt
14. cter When you have entered the new name navigate to the OK button on screen and press OK on the remote control to confirm the new name 8 To store the changes and exit the menu press EXIT 7 1 2 EPG Electronic Programme Guide Please refer to section 6 8 above 7 1 3 Sort Here you can sort your channels in the following order Default Sort the channels in the original order By Service Name Sort the channels in alphabetical order A Z By Frequency Sort the channels in frequency order Low High P12 MAIN MENU K By Encrypt Sort the channels from free to scrambled 72 Picture Press MENU then select Picture In this menu you can adjust the video settings Press AV to select an option and lt P to adjust the setting Press EXIT to exit ey the menu Aspect Ratio The default and recommended format is Auto You can also set the display format to available settings like 4 3 Full Screen 4 3 Pan amp Scan 4 3 Letter Box and 16 9 Wide Screen 4 3 Letter Box The full 16 9 picture will be displayed on your 4 3 TV set with black bars above and below the picture 4 3 Pan amp Scan The centre of the 16 9 picture will be displayed full screen on your 4 3 TV 4 3 Full Screen Combination of Letter box and Pan amp Scan 16 9 Wide Screen Select when using a 16 9 TV set TIP You can change the video output format directly from viewing mode by pressing the YELLOW button on the remote contr
15. d set the LNBs in the DiSEqC point The scan process will then search on all selected satellites 4 1 2 Signal Adjust The signal quality bar on the bottom of the screen allows you to fine tune the alignment of your antenna for optimum reception Adjust your antenna for maximum possible signal quality When the signal cannot be improved anymore fix the dish on this position and press the BLUE button for Scan P7 FIRST TIME INSTALLATION P OV 4 1 3 Scan Mode Six O K 04 5 Ce Use AV lt P to highlight your options of choice and press OK to start Se Channel Search It is recommended to use the default settings LA 4 1 4 Channel Search Your receiver will now perform an automatic channel search When the process SCH been completed all found channels will be stored and the receiver will switch to the KA first channel in the channel list You are now ready to enjoy your new receiver x NOTE M If no channels were found during the automatic channel scan the receiver will return to the First Installation menu Please select your language again and refer to chapter 7 3 for further instructions 5 0 QUICK GUIDE FOR USING YOUR RECEIVER We at THOMSON understand that you can t wait to enjoy your new HD receiver The fol device Io tum your receiver ON the button on the front panel owing quick guide will make you familiar with the basic operation of this We do however advice you
16. eV Six O signal PROBLEM POSSIBLE CAUSE WHAT TODO No picture The receiver can t receive Check the antenna le replace the cable or cinnect the cable to the receiver te Wrong direction of the dish Check the signal strength and adjust your dish correctly No picture or nput is not selected on Switch to correct TV input sound on TV your TV TV or VCR is not connected Check mains lead O main Firmly plug in cables between Bad cable connection receiver and TV Audio muting Press the MUTE button The receiver is switched to Press DTV VCR button DVDWOR SCART input TV power off Tum TV on Scrambled Channel is scrambled Select alternative channel channel message No response to remote control Receiver off Plug in and tum on plug andset not aimed Aim handset at IR sensor correctly R sensor obstructed Check for obstructions and set batteries Replace handset batteries automatically exhausted Password Contact local Service Hotline forgotten or send email to our Support via www thomsonstb net The external Power consumption is too Connect an extra power USB HDD does high supply adapter to your USB not start HDD device The receiver The Auto Standby function In the System gt Auto switches to is activated and reached the Standby menu you can adjust stand by adjusted time default 3h the auto p
17. end playback of the next file starts GOTO Opens a counter banner for entering the time moment you want to jump to Use the 0 9 buttons for entering the time and OK to confirm 4 WW Start playback of the previous next file REPEAT Press once for single file repeat twice to repeat all files or three times for random playing The symbol for the selected repeat mode will appear at the top of the screen Press once again to return to the common play mode RECALL Goes to the parent folder EXIT To get back to the Multimedia menu Press EXIT again if you want to leave the Multimedia menu TIP Playback of music will continue as long as the Multimedia menu is active This allows you to listen to music while watching photos Just exit of the Music submenu and select the slide mode in the Photo submenu like explained below Photo Your receiver allows you to watch a slide show with all available photos in the chosen folder To use the slide show choose a folder with photo files Press gt to start the slide show and W or EXIT to stop See the different Photo Configure options explained in point 7 7 2 below P21 MAIN MENU P OV Six P22 KA In the Photo mode following functions are available OK Opens selected photo in full screen format PA gt Starts the slide show II To pause resume the slide show Di E or EXIT To close the full screen format or to the stop slide show og return to the folder view 2 i To
18. eries 8 Close the cover NOTE The batteries should not be recharged disassembled electrically short circuited be mixed or used with other types of batteries 2 6 Using the remote control Fig 5 To use the remote control point it towards the front of the digital receiver The remote control has a range of up to 7 metres from the receiver if properly aligned towards the IR eye on the front panel The remote control will not operate if its path is blocked NOTE Sunlight or very bright light such as TL lighting might decrease the sensitivity of the remote control 3 0 CONNECTIONS 3 1 Basic connection using a Scart cable Fig 6 a Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a good quality coax cable and suitable F connector plugs b Connect one end of a good quality Scart cable to the TV SCART connector on your receiver and the other end to the SCART input of your TV c Plug the power cord to a suitable wall outlet 3 2 Basic connection using an HDMI cable Fig 7 P6 CONNECTIONS a a Connect the LNB of your satellite antenna to the SAT IN connector our receiver using a good quality coax cable and suitable F connector pi A D Connect one end of a good quality HDMI cable to the HDMI output on yr receiver and the other end to the HDMI input of your TV E c Plug the power cord to a suitable wall outlet ey Ki 3 3 Connecting mul
19. fast rewinded to the beginning playback of the current file will be resumed When it has fast forwarded to the end playback of the next file starts With the M4 bbl buttons you can jump to the previous next video file In the Movie mode it is also possible to use the REPEAT button its functionality is explained in the Music section above THOMSON cannot guarantee the playback of video files although extensions are listed here as the correct playback depends on codec used data bit rate and resolution as well Please consult the THOMSON Hotline in your country to get more details 7 7 2 Photo Configure Slide Time You can adjust the slide show interval to 1 8 seconds Slide Mode You can select one of the 60 slide show effects or Random mixed effects Aspect Ratio Keep displays the picture in its original aspect MAIN MENU 9 K Discard displays the picture in full screen mode 2 7 73 Movie Subtitle 2 This subtitle function is only relevant in the Movie menu for movies which os subtitle files in srt or txt format K During playback press SUBTITLE to select language and confirm with OK During playback of Movie files you can press SUBTITLE twice to change the subtitle KA settings described below KA Subtitle Specific Choose subtitle size between Small Normal and Big Subtitle BG Choose subtitle background between White Transparent Gray and Yellow Green Subtitle Font Colour Choose sub
20. in to start multi scan on all selected transponders Press RED to add a new satellite In the pop up banner enter the satellite s name and position by using the navigation and numeric buttons Press OK to enter text input mode In the key table select a character by using the navigation buttons Press OK to input the chosen character When you have entered the name navigate to the OK button on screen and press OK on the remote control to confirm the new name Save he settings with OK or cancel with EXIT Press GREEN to edit the focused satellite For changing settings see explanation above Confirm changes with OK or cancel with EXIT Press YELLOW to delete the focused satellite Press OK to confirm deleting or EXIT to cancel MAIN MENU SS 7 3 7 Transponder Edit options Transponders can only be edited when the transponder list is on screen do this select the satellite you wish to edit and press GOTO to open the TP Ge D options below are now available Add transponder Press RED to add a new transponder In the pop up KA banner enter the transponders data with the navigation K and numeric buttons Confirm the settings with OK or Ki cancel with EXIT An existing TP cannot be stored again oe under the same satellite Edit transponder Press GREEN to edit the highlighted transponder In the pop up banner change the transponder s data with the navigation and numeric buttons Confirm changes wi
21. iver is in VCR mode Press the DTV VCR button again to retum to the digital TV content NOTE The setting Always increases the power consumption in standby mode The front panel LED remains green in standby 7 3 Channel Search To access the menu press MENU and select Channel Search It contains two options Installation and DB Data Base Management Select an option and press OK to enter it Press EXIT to exit the menu 7 3 1 Installation 7 3 2 Satellite Selection Use the AV buttons to highlight the satellite your dish is aimed at Its antenna settings will be shown at the right side You can enter the right side with the lt gt buttons and retum to the satellite list with EXIT 7 3 3 Configure the antenna settings for selected satellite 2 22222999 LNB Type Press lt P or OK to show the list of LNB Types which is shown as frequencies You also can enter customized requencies with User Single or User Dual at the bottom of he list The default setting is Universal LNB 09750 10600 the most used on the market LNB Power Use lt gt to set the LNB power 13 18V is the setting for a Universal LNB 22KHz Use lt gt to switch the 22 KHz oscillator signal on or off Auto is the setting for a Universal LNB Toneburst To enable or disable the toneburst switcher if available DiSEgC1 0 To select the right port from up to 4 if available for the ight LNB DiSEgC1 1 To select the right port from up to 16
22. ld password or the default password 0000 You will then be asked to enter your So new password To confirm re enter your new password Press EXIT to exit the menu after confirming Restore Factory Default Reset your receiver to the default factory settings Select Restore Factory Default in the main menu and press OK or to select Enter your password or the default password 0000 and press OK to confirm This option will delete all your channels and settings The receiver will reboot and start with the First Installation menu WARNING A factory reset will permanently delete all your personal settings timers and stored channels Please consider this before you perform a factory reset Information Shows model software and hardware information Recall List Enable or disable the Recall list function which supports multi recall channel switching If the status is set ON then by pressing the RECALL button a list of all previously selected channels will be displayed for new selection If the status is set OFF then by pressing RECALL button the receiver will switch to the previously selected channel Software update Select Software Update in the main menu and press OK or to select There are two software update options available SW update by OTA The OTA Over the Air function allows you to search for software updates available on satellite Please ask your local THOMSON dealer or visit our website www thomson
23. o your receiver or to any magnetic objects such as loudspeakers ransformers etc Do not use a damaged power may clean your receiver with a soap solution and only after di ire or an electric shock cooling of the components ins Safety Precautions lever try to open the receiver due to high voltages and possi personnel When you are connecting cab he mains supply voltage Wait tis a necessity that you only u hat is suitable for the electrical cord It may cause a fire or an electric shock Do not ouch a power cord with wet hands It may cause an electric shock When the receiver is not used for a long period of time you should unplug the power cord from the wall socket Do not use alcohol or ammonia based liquids to clean the receiver If you wish you soft lint free cloth slightly made damp with a mild connecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause Do not place any objects on top of the receiver because this might prevent proper ide It is dangerous to touch the inside of the receiver ble electrical hazards Opening the receiver will void he warranty of the product Refer all maintenance or servicing to suitably qualified les be sure that the receiver is disconnected from a few seconds after switching off the receiver before you move the receiver or disconnect any equipment se an approved extension and compatible
24. ol Resolution If the video does not appear correctly change the setting These settings match the most common settings for HDMI 480i for NTSC system TV 480p for NTSC system TV 576i for PAL system TV 576p for PAL system TV 720p for NTSC or PAL system TV 1080 for NTSC or PAL system TV 1080p for NTSC or PAL system TV TIP You can change the video resolution directly from viewing mode by pressing the GREEN button on the remote control TV format Set the standard corresponding to your TV set Available options are PAL and NTSC Video output This setting is only relevant when the receiver is connected to the TV set via Scart Select RGB for the best picture quality or CVBS in case your TV doesn t support RGB Loop through VCR to TV Scart This option is only relevant if you have a device video DVD recorder connected to the VCR scart connector of your receiver Its signal will be looped through to P13 MAIN MENU Eml Six P14 Gy the TV scart output of your receiver Use this option to set the prefere joop through mode Running mode The Loop through will be switched off when the ven is in standby mode Always The Loop through is always on in operation and in KA standby mode X Switching between DTV VOR contents in the operation mode is realized by using KA the DTV VCR button on the remote control AV IN will be displayed on the front 4 LED display when the rece
25. open close the photo details banner while in full screen KA or slide snow mode 49 RED To zoom a photo use A V lt P to navigate to a certain part of the zoomed picture GREEN To turn the photo counter clockwise YELLOW To turn the photo clockwise GOTO Opens a grid view to go back press EXIT RECALL Goes to the parent folder K lt WW Open the previous next photo REPEAT The functionality is explained in the Music section above When you enter the Photo menu while listening to music then tmusic playback will automatically switch to the repeat all mode You can now enjoy pictures while listening to music and use all the repeat functions for photo playback in the slide show mode EXIT To get back to the Multimedia menu Press EXIT again if you want to leave the Multimedia menu Movie In the Movie menu you have to navigate to a movie file Select the file and press OK to start playback in the preview mode Use the RED button to switch between preview and full screen Use RECALL to go to the parent folder During playback you can use the playback control buttons such as 11 gt Raa bb 4 and yl You can check file details by pressing the i button in full screen mode To close the banner use again or press EXIT Use the GOTO button and enter the time moment you want to jump to with the 0 9 buttons then press OK to confirm With the 44 gt buttons you can rewind or forward playback in x2 x4 x8 x16 and x82 speed When it has
26. ower down time or disable it 9 0 SPECIFICATIONS Demodulator Demodulation Input symbol rate P24 QPSK 8PSK DVB S QPSK 1 45 Ms s DVB S2 8PSK QPSK 10 30 Ms s tightly GA ncorrect values of some Set the values of tuner Ta uner parameters parameters correctly in the 5 Installation menu KA SPECIFICATIONS Ki FEC decoder Auto 1 2 2 8 3 4 5 6 7 8 in CH Ode 1 2 3 5 2 8 3 4 4 5 5 6 8 9 10 S2 mode en 3 5 2 3 3 4 5 6 8 9 9 10 in 8PSK mode Video Decoder Ki 7 Profile level PEG 2 MP ML MP HL MPEG 4 H 264 AVC Op Input rate ax 20 Mbit s Sa Aspect ratio 4 3 and 16 9 Pan amp Scan Pillarbox Letterbox S Auto Video resolution PAL 50Hz 576i 576p 720p 1080i 1080p ITSC 60Hz 480i 480p 720p 1080i 1080p Audio Decoder Audio decoding MPEG 1 Layer 1 amp 2 ACB Downmix Audio mode ono L R Stereo AC3 Sampling rate 82 44 1 48 kHz Tuner Type F Type IEC169 24 Female nput frequency range 950 2150 MHz RF impedance 75 Ohm unbalanced Signal level 65 to 25 dBm LNB power 13 18 VDC 5 max 0 5 A overload protected DiSEqC versions 1 0 1 1 1 2 1 3 Tone burst System amp Memory ain processor MSTAR MSD7816 Flash memory 4 MBytes System memory 64 MBytes Multimedia Video playback Supported in various formats MPG MPEG TS VOB MP4 AVI Audio playback MP3 WMA formats Picture view JPG BMP formats THOMSON cannot gu
27. pends on broadcast 6 3 Selection of audio language Some channels support a choice of different audio formats and or languages To select another audio stream press AUDIO in viewing mode A list with available audio streams will now be displayed Use AY to select a stream and confirm with OK With the lt P buttons you can select between mono left mono right or stereo audio 6 4 Teletext Your receiver includes a fully featured Teletext To access Teletext press the TEXT button in viewing mode and use the 0 9 or AW buttons to select the number of the page you want to see Subpages if loaded and available can be selected with the lt P buttons The coloured buttons of the remote control allow you to jump to P9 OPERATION Eml Six Se selected pages directly as indicated on the bottom of the teletext scien Press TEXT again or EXIT to go back to viewing mode D 6 5 Subtitles Lan Some programmes support a choice of different DVB subtitle languages Press Pe SUBTITLE button in viewing mode to display a list of available subtitle languages 4 Use AV to select the subtitle language and confirm with OK 5 e 6 6 Changing the Aspect Ratio To change the Aspect Ratio while watching TV simply press the YELLOW button in viewing mode Each press will switch to the next format Please refer to section 7 2 for more details 6 7 Changing the resolution To change the Resolution while watching TV sim
28. ply press the GREEN button in viewing mode Each press will switch to the next format Please refer to section 7 2 for more details 6 8 EPG Electronic Programme Guide The Electronic Programme Guide is a very useful function that allows you to watch programme schedules and information on screen Press the EPG button to activate this guide you can also enter the EPG via the menu too Use AV to select a channel and RED to move the highlight to the programme list In the programme list use A W to select or scroll through programmes and lt P to display programme information for the next previous days Use BLUE to display detailed information about the selected programme If there is more than one page of information use lt P to scroll NOTE Availability of EPG data depends on broadcast Booking a programme from EPG Select a programme as described above Press OK when you have selected the programme This will lead you to the Timer Schedule menu All details are already led in for you Save the timer with OK To display the list of booked events just press the BLUE button in the channel list part of the EPG or in viewing mode Please refer to section 7 4 1 for more details 6 9 Favourite channels Use the FAV button to access your favourite channels and to toggle between available favourite groups Please refer to section 7 1 1 for details on how to create avourite lists 6 10 Changing between DTV VCR contents The receiver
29. rafpne while zapping between programmes in normal viewing mode in the channeklist mode the skipped channels remain selectable K S 3 Repeat the previous step to skip more programmes 0 4 To confirm and exit the menu press EXIT Disable a skipped TV or radio programme Press the GREEN button on the programme marked with the skip symbol Move aTV or radio programme 1 Select the programme you want to move then press the RED button Amove symbol will appear 2 Press AW to move the programme 8 Press OK or RED again to confirm the new position 4 Repeat the steps above to move more channels Locking programmes ou can lock selected programmes for restricted view 1 Select the programme you want to lock then press the YELLOW button The programme is now marked as locked 2 Repeat the previous step to select more programmes 3 To confirm and exit the menu press EXIT To view a locked programme you need to enter either the default password COOC or your last set password We recommend changing the default password to one of your preference Please refer to chapter 7 6 System for more details Disable a locked TV or radio programme Press the YELLOW button on the programme marked with the lock symbol Rename aTV or radio programme 1 Select the programme you want to rename and press the i button A key table appears 2 In the key table select a character by using the navigation buttons Press OK to enter the chara
30. stb net for more information In the OTA menu all necessary THOMSON OTA settings Satellite Frequency Symbol rate and Polarization are already set per default but could also be changed manually Press OK to initiate the update process An attention banner will now be displayed Press OK to start the update or EXIT to cancel it Follow the instructions displayed on screen The software searching and update process could take up to 20 minutes depending on the data volume in stream After the process has been completed also if no update was found the receiver will reboot and start with the last shown channel P19 MAIN MENU P OV Oix ey WARNING NEVER power off the receiver or pull the mains plug SCH Ge software upgrade process Doing so might cause irrepar damage to your receiver and will void your warranty 2 SW update by USB ag Download the required update file for your receiver model from our website www homsonstb net support page or contact your local dealer KG 3 Unzip the file on your computer if necessary and copy it to root folder of your USB D storage device Connect the USB storage device to the USB port of the receiver Press MENU and select Software Update By USB Press OK to enter the software file list Select he file containing the software image and press OK to initiate the software update An attention banner will now be displayed Press OK to start the update or EXIT o cancel it
31. t 4 GREEN In viewing mode changes the resolution of the HDMI output between 1080p 1080i 720p 576p and 576i several functions in the OSD menu and Teletext P4 YOUR RECEIVER 22 23 24 25 26 FAV YELLOW BLUE SUBTITLE TEXT AUDIO RECALL 44 Wetz REPEAT MENU EXIT AV OK lt gt EPG VOL ee n viewing mode changes the aspectatio and aspect conversion of video outputs several unctions in the OSD menu and Teletext 4 n viewing mode displays the schedule menu for easy setup of timers several functions in the O menu and Teletext To select one of the available subtitles languages KA or the current channel Ki o open Teletext if available on the current channel Displays the audio selection menu for available anguages and audio modes To switch between the last viewed channels Searches backwards during playback Each pressing increases the speed x2 x32 Searches forwards during playback Each pressing increases the speed x2 x32 Jumps to the previous file during playback Jumps to the next file during playbac Starts resumes playback Freezes resumes playback of multimedia files Stops playback of multimedia files Selects different repeat modes during playback To open the main menu in viewing mode or to go one step back in the menu Go one step back in the menu cancellation of current process exit from the main menu to viewing mode Swit
32. th OK or cancel with EXIT Delete transponder Press YELLOW to delete the highlighted transponder Press OK to confirm or EXIT to cancel 73 8 DB Management This menu allows you to save and reload the channel data base of your receiver from to a USB device This very convenient feature enables you to save your personal settings like Channel Favourite Sat and TP lists on a USB storage device and load them back to the receiver later This feature is especially helpful after unintentional changes or factory reset In such cases just skip the First Installation by pressing EXIT in the First Installation and select the DB management menu Connect the USB storage device to you receiver and select one of the options 7 3 9 Load from USB __ sss Press OK for displaying the list with available DB files if any stored before The DB files en DBM are shown with their built date day and month Select the DB file you want to load and confirm it with OK If DB was loaded successfully message appears on screen the receiver switches automatically to the first stored channel and shows its content in the background Press EXIT until the OSD menu disappears 7 3 10 Backup to USB Press OK to make a backup of the data base A DBM File xxxxx DBM with the current date day and month will be created on the USB device If DB was stored successfully a message will be displayed on screen Press EXIT until the O
33. tiple fixed LNBs using a DiSEqC 1 0 switch Bei Fig 8 a Connect the LNBs of your fixed antenna to the inputs of a DISEqC 1 0 switch b Connect the output or to receiver connector of the DISEgC 1 0 switch to the SAT IN connector on your receiver c Refer to section 3 1 or 3 2 for TV and mains connections 4 0 FIRST TIME INSTALLATION After all connections have been made properly tum on your TV and make sure the receiver is connected to the main power If you are using the receiver for the first time or restored it to factory default the First Installation menu will appear on your TV screen Use the lt P buttons to select the OSD Language of your preference and press OK to confirm An Info page will be displayed Read the info guide and press the Z button to proceed to the next Installation step You can open and close the info page again by using the button NOTE If German is selected as language German preset channels from ASTRA 19 2E will be installed You can continue with the Installation menu to scan and install further channels as described below or directly go to viewing mode by pressing the EXIT button twice to start enjoying the pre installed channels immediately 4 1 Installation 4 1 1 Satellite Selection SSS Use AV to highlight the satellite your dish is aimed at When using a multi feed antenna with more than 1 LNB select the satellites your antenna is adjusted for by pressing the OK button an
34. title font colour between Red Blue Green White and Black 7 7 4 Format WARNING The format function will delete all data and information from your USB device or selected partition THOMSON will not take any responsibility for damaged or lost data on the USB device If you have multiple partitions on your storage device select the partition you want to format and press OK to continue An attention banner will now be displayed Press OK to start formatting or EXIT to cancel The format procedure will take some time depending on the size of the used storage device At the end of process the Formatting is complete message will appear Press EXIT to exit the menu 8 0 TROUBLESHOOTING There may be various reasons for abnormal operation of the receiver Please check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact your local Service line or THOMSON dealer Alternatively you can send a support mail via our website www thomsonstb net NEVER open or disassemble your receiver This may cause a dangerous situation and will void the warranty PROBLEM POSSIBLE CAUSE WHAT TO DO Standby Mains lead unplugged Check mains lead switch indicator does multipoint connector multipoint connector on not light up switched off Front panel switch is in OFF Set front panel switch to ON position position P23 TROUBLESHOOTING P
35. to read the full manual to get the best performance from your THOMSON HD receiver or to standby use the W button on the remote control or Choose a channel with the A W buttons Alternatively you can digit the channel number with the 0 9 but display the channel list The volume can be adjusted with the lt P buttons 6 0 OPERATION In viewing mode several features are available to make watching TV a true pleasure This paragraph describes these features Please also read chapter 7 to get familiar with the menu of your new receiver 6 1 Changing channels ttons on the remote control or press OK in viewing mode to There are different ways to change channels with your new receiver Via direct access Via the channel list Via the A V buttons Via the RECALL button 6 1 1 Direct access To gain direct access to a certain channel simply input its number with the 0 9 buttons on the remote control Channel numbers can be up to four digits long Entering a number with less than four digits is possible Just wait a few seconds and your receiver will switch to the selected channel P8 QUICK GUIDE FOR USING YOUR RECEIVER KA G 6 1 2 Channel list Press OK in viewing mode to display the channel list Use A V to highligh your channel of choice and press OK once to select the highlighted channel Th channel list is equipped with a Find function to make it easier to find a certain channel Press
36. utton A Favourite Type window will pop up on screen The following 4 groups are available Movie News Sport and Music Please select one or more of them A star shaped symbol will appear and the programme is marked as a favourite Press EXIT to retum to the channel list for further selection 2 Repeat the previous step to select more favourite programmes 3 To confirm and exit the menu press EXIT Disable favourite TV or radio programme Repeat step 1 described above and select Disable in the Favourite Type window View favourite programme 1 Press the FAV to display a list of favourite programmes in normal viewing mode no menu mode While in the favourite list use 4 to switch between available favourite lists 2 Select your favourite programme with A Y and press OK to switch to it 3 Now you can select channels from the chosen favourite group only by pressing AY in viewing mode If you want to change to the main channel list press OK in viewing mode and then press GOTO and select All satellites Delete aTV or radio programme 1 Select the programme you want to delete and press the BLUE button A message will appear Press OK to delete the programme or EXIT to cancel 2 Repeat the previous step to delete more programmes P11 MAIN MENU P OV Six KA Skip TV or radio programme 1 Select the programme you want to skip and press the GREEN button 2 The programme will be marked to skip The receiver will skip this prog
37. warning information NOTE Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold Characters Move to Represents a menu item within a window Italic Characters 1 4 Accessories 1 User Manual 1 Remote control unit 2x Batteries AAA type NOTE The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries If rechargeable accumulators instead of batteries are going to be used we recommend using e g NiMH types with low self discharge to ensure long time operation of remote control 1 5 Usage of external USB devices is recommended to use USB 2 0 storage devices If your device is not compatible to USB 2 0 specifications multimedia functions of the receiver might not work properly THOMSON cannot guarantee compatibility with all tyoes of USB storage devices is advised not to store important information on USB storage devices used with he receiver Always make backups of data on your USB storage device before using it with this receiver THOMSON will not take responsibility for any loss of information or circumstances caused by loss of information Please ensure that either the USB device is already formatted to FAT FAT32 or ormat the USB device via your receiver refer to chapter 7 7 USB for details P3 INSTRUCTION Eml Six
38. will move the dish to the selected satellite automatically For Move Continue Move Step 1 and Goto Reference please see explanation above 7 3 4 Channel Scan Automatic Scan Single Satellite Scan Press BLUE for Scan A window with scan settings will be displayed Scan Mode Use lt P gt to select Default Blind Scan or NetWork Default All stored transponders in the memory will be scanned Blind Scan Slow scan in 2 MHz steps The receiver will first scan he whole frequency band to find the transponders it can ock on After gathering all transponders it scans the ransponders one by one to get all available programmes NetWork etwork search will be performed when network information is broadcasted new transponders will be found and stored Crytped Press lt P to select All Channels scrambled and free or FTA Channels free to air Service Type Press lt P to select ALL DTV or Radio After configuring press OK or BLUE again to start scanning with the selected settings Your receiver will now perform an automatic channel search with the scan progress shown on screen During the channel search you can skip transponders by pressing the MENU button or quit the scan process with EXIT When the process D 5 MAIN MENU P eV Six has been completed all found to the first found channel Multi Satellites Scan select OK bui symbo BLUE for Scan A window with scanning settings will be display Single Satellite Scan above
39. wiring power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate ai 1 2 Storage Your receiver and its accessori he back of the receiver f the receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer es are stored and delivered in a packaging designed o protect against electric shocks and moisture When unpacking it make sure hat all the parts are included and keep the packaging away from children When ransporting the receiver from one place to another or if you are retuming it under warranty conditions make sure to repack the receiver in its original packaging with INSTRUCTION a its accessories Failing to comply with such packaging procedures Cold damage the product and void your warranty A Ki 1 3 Equipment Set up h We recommend you consult a professional installer to set up your equipment ey Otherwise please follow the instructions below lt Refer to the user manual of your TV and your antenna Make sure that the SCART HDMI cable and outdoor components are in a good e condition and the SCART HDMI connections are well shielded and from good quality This manual provides complete instructions for installing and using this receiver The following symbols will serve as follows WARNING Indicates
Download Pdf Manuals
Related Search