Home

PF102

1. 495mm 422mm a E a pee A D N 455mm E 1 E A For purposes of product enhancement certain specifications or appearance may be changed without notice Copying any part or the entire contents of this manual is probited The contents of this manual may be changed without notice If you have noticed any errors or omissions please contact our support desk Our Support desk Phone Number 0120 481 484 Free dial Open Hours 10 00 to 17 00 Mon to Fri Not available Sat Sun national or business holidays Homepage http kneader jp Japan Kneader CO LTD 2346 1 Hongo Ebina Kanagawa Japan postal code 243 0417 http kneader jp 602A50292
2. Appliance Fermenter heater folding plate top plate door Accessories Shelf plates 2 Humidification dish Convection board User s manual this book Warranty card X Recipes Operating Instructions Preparing the Fermenter Place heater on a stable surface 3 Attach the folding plate to the heater Fit the groove of the folding plate to the heater at the mounting knob Snap the rear folding plate onto the heater pressing against the top of the folding plate for easy attachment Be careful not to apply impact to the Temperature Sensor as that may cause it to disfunction D Groove os Mounting Groove SES knob Mounting knob Temp sensor 4 Mount and attach the top plate by lightly tapping by hand from the top Z I Front is written on the inside of the top plate Place it properly 5 Attach door while holding up the folding plate door can be attached either on the left or right Hold the door with both hands
3. KNEADER Fermenter Part number PF 102 Owner s Manual General household articles Please do not use for business purpose PINEA DER z O we eo LEB eo O N WT Thank you for purchasing the Kneader Fermenter PF 102 Please keep this manual so that you can refer to it in the future Before using this appliance be sure to read all the instructions This appliance was designed for use in Japan only and should not be used in other countries Table of contents Safety concerns Please observe oe Meaning of symbols Warnings Cautionary measures Tank usage Features of the Fermenter PF 102 Names of parts E eet See eee eter Main parts How to use ESANTA OESE EAE NE AE ANEA IEE A anaes Preliminary preparation of Fermenter Operating parts Using the Fermenter M intenancE ecesecsarreisseseiieennae tine Main body parts Disassembling and storage In case of malfunction AEA After sales service E E E E E sees Specifications E E EEE Safety instructions and warnings The content below consists of important safety instructions to prevent harm
4. S ESL Please press START is off you can reset by pressing wens Flashes for 5 seconds and afterwards and stand by screen will return Using the Fermentator Turn on the power switch The system performs a self check O 0FF gg will be displayed 1 ON i RO heHULTKCK PERL Please press START will blink Press gt ia Stand by screen will be displayed 2 Setting fermentation temperature and time Pressing eo the setting screen will appear Will show 35 C or 30 minutes Fermentation temperature is between 20 and 45 C Can be set in increments of 1 C Fermentation time is between 1 min and12 hours Can be set in increments of 1 minute The fermentation temperature and time can be changed anytime Set fermentation time and temperature according to type of bread E Dif START is pressed during Press BES preheating then preheating fermentation will be displayed Heating will start arid eount begie 4 When preheating process is completed a buzzer will sound Place dough inside 5 Press gt a Fermentation will start 6 When fermentation is complete a buzzer will sound The heater will turn off Please dry the inside and leave the door open to dry the Fermentor Please keep the inside of the Fermenter clean Returning to Stand by screen 23 5 When Press the Start is
5. after you have fitted the protrusion at the top of the door into the hole into the top plate while lifting the top plate lightly in the direction of the arrow and attach the lower protrusion of the door to the heater 6 Firmly attach the door to the heater and folding plate with the mounting knob Both sides im f Ti ji I Drying position The appliance can be dried by leaving the door ajar as shown 7 Place on horizontal surface a proper distance away from walls and other objects The front of the appliance should be kept clear Please leave a space of more than 4 5 cm from back and sides Please make sure that the table on which the Fermenter is placed is secure ORAS OE S E E sy 4 5cm zt Et 8 Attach the shelf plate and the convection board additional shelves Please insert the rack with the grills facing up EE a VA S d Shelves can be added as purchase options q NT q Shelf plate Convection board 9 Placing the humidification dish FIII dish with about 200cc of co
6. off press oO 1 When using for the first time there may be a smell of resin upon opening the door Place about 50cc of lukewarm water in a dish inside the Fermenter Smell will disappear after a while 2 Please keep the door closed to save electric power and maintain its condition Refrain from keeping the door open for long periods of time 3 This appliance is equipped with auto off feature enhancing safety and its eco friendly design If after the preheating process the fermentation process has not been started if the setting temperature and inside temperature difference are too great and within 1 hour the set temperature cannot be reached the heater will turn off automatically 12 13 Maintenance Please keep up maintenance per use Caution When you are done be sure to remove the plug from the wall outlet Do not use benzine thinner polish scrub brush nylon scrub brush steel wool etc to clean the device e After use wipe off water droplets that appear on the inside of the fermenter and the door with a cloth then leave the door open to dry e Also please wipe with a cloth while using the fermenter if there is excessive water e Please wipe off water oil dough etc thoroughly with a cloth e When cleaning and maintaining please do not drop or apply impact to the fermenter e Please keep the inside of the fermenter clean Appliance Before cleaning please be sure the hot plate
7. or damage to yourself or others Please be sure to follow instructions In case of wrong usage what may occur LN Warning Can lead to serious injury or death AN Caution Can lead to harm to persons or damage to property About the Symbols The meanings of the symbols are as follows S Never do amp Do not use near fire Do not touch Use only in dry environment Never use in damp places such as baths washrooms or on wet floors Be sure to unplug from the outlet Do not handle plug with wet hands Do not attempt to repair or modify the appliance Aways obey the display signals Refer all servicing to authorised repair technicians Extremely hot Specific explanations on appliance gt OG Use this appliance according to the written cautions and warnings Carefully avoid any accidents A Warning Do not damage or modify C Remove the dust from the power plug S the power cord Dusty plugs are fire and electrical shock hazards Damaged or modified cords are fire and electrical shock hazards Do not excessively twist Do not use plug with wet hands pull or bend the power cord Doing so can damage the cord Damaged cords are fire and electrical shock hazards S Do not place objects on power cord S Do not overload outlets Doing so may produce severed elements and short circuits In addition do not damage the power cord If the po
8. e lower surface of the heater Operating Unit Display Info displayed error codes etc About serial number SER We use a Serial number as an identification number for this product You will find the serial number label it on the lower PUA be SA ALB PF102 EREE 100V ERBABI 150W HERM 50 60H2 SUNEEe Olen eats aaa Trini ieee Write the number and date of purchase down in the SER gt KK gt K gt K gt KK KKK boxes below in order to be able to confirm the _ number promptly Serial number SER is 9 digits date of month day year Specifications Main specifications are as follows Power supply AC 100V for both 50Hz and 60Hz Power consumption Timer 150W minimum 1 minute maximum 12 hours 720 minutes Temperature setting range Displayable internal temperature of Fermenter 20 C 45 C Recommended temperature range 18 C 30 C 10 50 C under 10 C LO over 50 C gt HI Current temperature fuse Temperature monitoring system automatic switch off function 495x422x455mm 434x348x360mm approx 1 5 m Safety features External dimensions WxDxH Internal dimensions WxDxH Cord length Product weight approx 7 0 kg W Dimensions
9. has completely cooled down There is a risk of burns The housing portion of this appliance folding plate top plate door shelves convection board can be washed after disassembly except for the heater You can wipe surface dirt off lightly with a cloth Please wipe with a dry cloth until completely dry If it is very dirty continue to wipe and wring out the excessive water in the cloth Mold may form if appliance is stored with moisture remaining inside This can cause deterioration of the insulation and decrease performance After using the fermenter make sure to leave the door open a little to air dry the inside The door can be left open For safe usage keep the door in the drying position Drying position of the door The door can be left half open Disassembly and storage Turn off power switch and unplug from wall outlet 1 ON l Oe Remove shelf plate humidification dish and convection board SSS j 3 Loosen mounting knob on both sides Both sides Mounting Knob A imi TT 4 While holding the appliance down with one hand lift the door gently from the bottom with the other hand and remove the door attachment protrusions of the door top first and then bottom 14 5 Remove the top p
10. ing or tipping of this product can cause injury Always use placed on a flat stable surface May not be used in vicinity of fire or water QG Fire hazard Water may get into appliance causing electrical shock hazard Never place any objects on top of the appliance Placing things on the appliance surface may cause it to be deformed or damaged Do not pour water over the operating panel Electrical circuit may fail In case of getting wet wipe immediately with a dry cloth Do not place more than weight of 5kg on the shelf plate Do not place excessive weight on the shelf plate There is risk of damage Do not use other than fermentation of bread dough or yeast leaven May overheat and cause accident if used to dry cloth When disassembling make sure to start from door Otherwise door may fall causing risk of injury S Do not clean with flammable solvents Fire hazard Do not touch the hot plate or humidification dish when in use or immediately afterwards The top of the heating plate may reach the temperature of 100 C Please do not touch t Keep unplugged when not in operation e g cleaning or maintenance Risk of injury During maintenance be sure to unplug Recommendations for appliance operation In the following cases unplug and stop operation immediately Please consult our support desk When power switch doesn t work If power cord or pl
11. late and the folding plate then fold the folding plate N 7 ON 2 6 Remove the condensed water Remove the crick of the gutter rotating slightly in the direction of the arrow remove and clean the crick N FF WIS Pull the condesation water recovery bottle then discard the water in the bottle VA Store after disassembling QS Mm 15 In the event of failure Please check the following before requesting repair Display EO E1 E2 E3 E4 Flashing Entire LCD screen flashing Problem No display appears even after switch is turned on Temperature does not rise Temperature does not fall Does not
12. ld or lukewarm water and place in the center of the hot plate If used for a long time add more water to the humidification dish y Humidification dish O Plug into an electrical outlet Please use an outlet of 100V Do not overload outlet Storage method After pre heating is completed f Oven dish f j p p g p q p q 4 Refrigerant q In the case of small rolls 3 to 6 stages To lower the temperature you may of oven dishes will fit place a refrigerant on the convection board D fal p q p g q p q OKNEADER p p E a SSE S When using a pot manufactured by You can bake up to 4 loaves of bread the Japan Kneader Company after place the pot on the bottom convection board 10 11 v button once Setting Temperature button When you press the or button the word azz settings will flash on and off Please set temperature while settings is flashing To increase or decrease by 1 C press or To increase or decrease co
13. ly possible for up to one hour press the START button before time is up switch to fermenting process If issues persist even after following the above please contact our support desk See page 17 After sales services 16 17 After sales services Please contact our support desk for consultation on repair handling and purchasing of parts Guarantee deadline conditions Guarantee period is one year from the date of purchase e Repair within the guarantee period Our support desk will respond in accordance with the contents of the guarantee e Repair beyond the guarantee period If your Fermenter has a technical issue and is repairable it will be repaired for a charge as per request Holding period of repair for performance parts The manufacturer ensures availability of replacement parts and repairs for up to 6 years after the manufacture of this appliance has been discontinued Replacement parts Spare parts required for the operation of the product Our Support desk Phone Number 0120 481 484 Free dial Open Hours 10 00 to 17 00 Mon to Fri Not available Sat Sun national or business holidays Homepage http kneader jp When contacting us we may ask you for the part number serial number and contents of the operation unit Please prepare these before contacting our support desk Part Number Written on the operation unit or on the cover of the Owner s Manual Serial Number Labelled on th
14. ntinuously press and hold until you reach your desired temperature How to operate eA QO KNEADE A Setting fermentation time button When you press the or button the word azz settings will flash on and off To increase or decrease by one minute press or button once to increase or decrease continuously press and hold until you reach your desired time Maximum time setting is 12 hours R ims Power switch Temperature display Temperatures from 10 C to 50 C can be displayed Less than 10 C will be displayed as LO Over 50 C will appear as HI Temperature setting range is between 20 C and 45 C When it reaches the set temperature you will be notified by buzzer a Fermentation time display The time count starts when fermentation begins Start Button Power up screen AS bheHUTCIESV Please press START will blink Stand by screen RO bheHULTCIESV Please press START will blink Preheating will start after 35 0 pressing gt WUeoh Preheat screen PA Preheat will blink Aget Press o Fermentation will begin End of Preheat screen AS KALT IES Please press START will blink Press Q Fermentation will begin Fermentation screen F Fermentation will blink Fermentation completion screen returns to stand by screen When AY K HRLT lt
15. reach the temperature setting When set to preheated to warm after hearing a beeping sound temperature suddenly falls What to do There may be a problem with the temperature sensor if the error code does not disappear from the display even when you operate the power switch Please turn off power unplug from outlet and contact our support desk Make sure the folding plate is set properly gt Please set the plate in place Check to see if the door is open gt Please close the door securely Is the convection board set gt Please set the convection board properly in place Things to check for Is the power cord securely plugged in gt Please plug in securely or insert the plug into another outlet Is the power switch turned on gt Please make sure it is on Did you press the START button gt Please make sure that preheating light is on Check to see if the setting temperature is not below room temperature gt Please use a temperature setting higher than room temperature Check that the temperature setting is not below room temperature gt Since this product does not have the ability to cool itself it can be set at a temperature below room temperature Please use above room temperature If room temperature is below 18 C or above 30 C it may not reach the set temperature This is not a malfunction Did you keep preheating for more than one hour gt Since the preheating is on
16. ug is damaged or frayed If the appliance has been deformed from falling If liquid gets into the the appliance the frame If the appliance has been exposed to prolonged rain and or wind If the appliance emits smoke or burnt smell does not work normally even in accordance with the Instruction Manual The warning label attached to the appliance contains important notes for your safety Please observe the following precautions e The attached safety label must be in a visible place and may not be covered or hidden e Do not remove or modify the label If the label has become damaged or soiled please request a new one You may contact our support desk to obtain a new label Accidents failure or visible deterioration due to factors such as excessive UV light extreme temperatures humidity detergent oil mold prolonged non use may occur due to natural aging Also general abrasion of parts and abrasion caused by repeated opening and closing of door over several years may lead to deteriorative failure Please always remember to unplug after use to prevent accidents Oo ARK W N OO Features of the Fermenter PF102 It can be easily assembled without tools Can be folded into a compact small size and doesn t take up storage space Door can be attached on either the left or right it does not choose the location The Storage Unit employs a double plastic structure lightweight and durable with e
17. wer cord is damaged it may cause an electric shock or fire Electrical shock hazard May overload circuits causing malfunction and electric shock A Warning S Do not wash heating parts If water gets inside the heater it may cause short circuiting or malfunction T Use with 100V AC outlet only Overload of electrical current may cause electric shock or malfunction Heating parts should not be disassembled or modified Disassembling or modifying heating parts can cause malfunction or fire Inside this appliance and high voltage component there is a high risk of electric shock causing serious physical injury Any internal inspection repairs for this product not disclosed or described in this manual should be referred to our support desk Do not share outlet with other appliances Branch outlet becomes abnormally hot when used with other appliances posing a risk of fire Children are strictly prohibited from using this product Do not keep within reach of children Risk of burns electric shock and injury other objects and keep a space of more than 4 5 cm from sides and walls Close quarters may cause malfunction or a fire D Leave the front of the appliance free of Do not place the lower shelf plate directly in front of the heater surface May cause malfunction or fire A Caution Do not use on an unstable surface or over a powdery oily surface Fall
18. xcellent insulation PAT 4613253 Can be used for up to 12 hours at a time Wide temperature range 20 45 C The Fermenter does not have cooling capacity feature it will not operate below room temperature The inner wall convection system patent pending can perform uniform fermentation in the lower middle and upper parts of the appliance with advanced air rotation system High precision temperature control all the three places have independent temperature control systems patent pending providing appropriate temperature environment Water condensation recovery system patent pending Door can be kept open to dry the inside of Fermentor drying position Names of parts Main components Top Plate Hollow construction Folding Plate plastic PP Door double structure Hollow construction Shelves iron plastic PE plastic PET plastic PP Power Plug Operation display Power switch Heat plate Water condensation bottle antibacterial plastic PP Heater flame resistant plastic ABS Mounting Knob 2 plastic ABS Lower convection board plastic PS Temperature sensor N ss Gutter for condensed water Humidifcation dish stainless steel plastic PC Operation manual Recipe D AA Warranty card a eas lt lt Appliance and accessories First please check whether the following items are all included

PF102

Contents

Download Pdf Manuals

Related Search

Related Contents