2015 ENG user manual for side snow plow KSM
Contents
1. fourteen 14 business days after the purchaser s written notice of the warranty case If the cause is covered by the warranty the seller shall eliminate it within 20 twenty working days after the expert analysis is carried out Warranty repairs shall be carried out at the shipping address specified in the order confirmation Repair work of larger scale shall be carried out in the territory of the seller Cost of transporting the product for warranty repair shall be paid by the purchaser The purchaser shall cover the expenses and transport costs for repair works excluded from the warranty terms and conditions Warranty shall not cover defects which are caused asaresult of natural wear and tear of the product asaresult of road surface characteristics or damage thereof In connection with the use of the product contrary to the technical requirements safety regulations and intended purpose due to failure to observe the maintenance requirements of the product duetoatraffic accident of which the purchaser has not notified the seller in writing within seven days following its occurrence and or the purchaser has not given the seller an opportunity to determine the cause of the defect pursuant to the contract Inthe extent to which the increasing of the defect could have reasonably been prevented by the seller Product warranty shall expire prematurely from the time when the product Is repair2. and without the moldboard extension Skid shoes must be adjusted so that the steel blades are 0 15 mm above the ground depending on the road surface Avoid excessive wear to the slide foot as it may break and fall off Always install the handle splint 2 Drawing and Drawing 17 after adjusting the skid shoe in order to keep the skid shoe at desired height 4 3 1 Using skid shoe on KSM3103 In case of steel blades both skid shoes can be used Fasten the front skid shoe by using the lower holes 3 Drawing 6 In case of rubber blades only the front skid shoe can be used Fasten the skid shoe by using the upper holes 4 Drawing 6 Drawing 16 Front skid shoe 4 3 2 Using skid shoe on KSM3703 In case of steel blades both skid shoes can be used Fasten the front skid shoe by using the lower holes 3 Drawing 6 Fasten the rear skid shoe by using the front holes 3 Drawing 6 WWW MEIRENSNOW COM 18 SIDE WING PLOUGH KSM 03 WW A if Ne Drawing 17 Rear slide foot when using the steel blades In case of rubber blades both skid shoes can be used Fasten the rear skid shoe by using the rear holes 4 Drawing 18 UNA ANN i NW aw 7 ASM 2 l SSX Drawing 18 Rear slide foot when using the rubber blades WWW MEIRENSNOW COM 19 5 MAINTENANCE OF THE SNOW PLOUGH SIDE WING PLOUGH KSM 03 MAINTENANCE IN EVERY 8 MAINTENANCE IN EVERY 150 MAJOR SEASONAL MAIN
3. that the fastenings are not damaged Check that the safety markings plough side lights if provided and reflectors are in good operational order Check the operational order of cutting edges if provided also the condition of slide feet or wheels The cutting edges shall be adjusted reversed or replaced latest when the distance between the cutting edge and the fastening openings is less than 30 mm Rubber blades must worn down or replaced at the latest when the blade reaches 10 mm below the bottom edge of the blade holder Check the condition of the fastening wedges of the blades Check the condition of levers and fastening pins of the cylinders Check that the hydraulic hoses are intact and properly fastened Check that the plough Is properly greased WWW MEIRENSNOW COM 4 SIDE WING PLOUGH KSM 03 Check that the plough has no damages Working with the snow plough To operate the plough the person shall be at least 18 years of age shall have a driving licence of the appropriate category and shall have read through the operation instruction of the snow plough Always pay attention to the surrounding and other traffic including from the side roads and to the vehicles approaching from the rear Pay attention to the pedestrians and cyclists not to cause them any risk when working with the snow plough All warning lights must always be switched on during working Follow the general traffic rules The maximum permitted operat
4. 3 Otherwise it will protrude from the vehicle dimensions Drawing 6 Pin of the lift cylinder 4 WORKING WITH THE PLOUGH The plough can be used for enlarging the working width during snow removal for cleaning the road shoulders as well as for cutting the snow walls on the road shoulders lower If you plan to enlarge the working width or clean the road shoulders the lift cylinder should be retracted completely to ensure that the plough s moldboard is in the floating position WWW MEIRENSNOW COM 11 SIDE WING PLOUGH KSM 03 If you want to cut the snow walls lower the plough s moldboard should be raised with the lift cylinder and the plough should be extended with the rotating hydraulic cylinder The cylinders are operating independently and therefore the plough can be first extended and then lifted It is also possible at any time to switch from cutting the snow walls to cleaning the road shoulders and on the contrary A In order to retract the plough s moldboard and lock it in the travelling position using the rear attachment the plough s moldboard must be raised with the lift cylinder and then retracted with the rotating hydraulic cylinder Both rubber and steel blades can be used on the plough In order to ensure optimal work with different types of blades the blade holders are replaceable Rubber blades should be used when the road shoulders are still soft and not frozen Steel blades should be used when the road shoulders a
5. LOUGH KSM 03 Raising bilateral action cylinder 1 pcs Turning bilateral action cylinder 1 pcs Dil usage 30 100 l min Maximum work pressure 150 200 bar Table 2 Hydraulics of the plough 1 1 Side wing snow plough in standard equipment Lifting frame according to the vehicle Set of pivot cylinder with rear mounting beam Set of Strobe emergency lights Skid shoe holder rear Skid shoe VAUTID 240 300 rear Mechanical impact and vibration reducer Impact relief valve for pivot cylinder Safety markings 1 2 Accessory equipment Blade holders Rubber or steel blades Extension unit 300 mm front Skid shoe holder front attached to lifting frame Skid shoe VAUTID 240 300 mm front 2 SAFETY REQUIREMENTS FOR OPERATING THE SNOW PLOUGH Before operating the plough Check that the plough set is complete and that it is in good operational order It is forbidden to use equipment that Is not in good operational order Check that there are no people or objects near the plough which could be injured or damaged by the plough In addition safety of people carrying out maintenance of the plough repairing the plough or moving the plough with the help of hydraulics or any other means has to be ensured Neglecting of the safety requirements can cause injuries to people It is forbidden to work under a plough that is lifted up and not supported Check that the plough is properly fastened to the truck or tractor and
6. SIDEPLOUGH KSMOQ3 MEIREN ENGINEERING OU VAIKE MANNIKU 7 TALLINN 11216 ESTONIA PHONE 372 682 5002 FAX 372 610 0589 E MAIL INFO MEIREN EE WWW MEIRENSNOW COM E USER MANAUL 2015 2016 This user manual applies to snow ploughs from serial number 0891XXXXXX SNOW MEIR Push your limits Expand your boundaries SIDE WING PLOUGH KSM 03 CONTENT CE DECLARATION OF CONFORMITY ccsssciceisiottacscestenttntadoasasnacsetins ofbacesess laut canensasenasmeaseosgadonnaeaavsaaceateouoanmiaesoadese 4 FOREWORD ssnin 5 GENERAL SAFETY REQUIREMENTS cessa deinen aeai E E E E EEE 5 PERSONNEL vorisi e E E S 5 1 PRODUCT DESCRIPTION se xtccetesiessteccectoourencasintesecbeticanssncnecstscsvac destacesmoeetcaescbocaedstecivee dectuedentrnlesessboceestaees 6 bet SIDE WING SNOW REOUGHIN STANDARD EQUIPMENT lt s cossc0scsesecsascencacuseatsnestaassnnybonueseaaastnduseenatosoeonionetaaeetacnstacemtesmeeesy f Te ACCESSORY EQUIPMENT satiascusc noenee aR a A O 2 SAFETY REQUIREMENTS FOR OPERATING THE SNOW PLOUGH 00 00 cc ccetccceceecserrceceessesecessesseeeees f 3 MOUNTING AND DEMOUNTING OF A PLOUGH eesooeeeeessseesessssecessssoccessssoccesessoocessssoceessssocesssssoeesssssoeceses 9 A WORKING WITH THE PLOUGH o oiriciioeseinoteireisiis eise a ian NEE EAE EEEE E EEE 11 AL vee CEN E ING it eB EP DE HOLDER canneto a aT E E 13 4 1 1 Removing and installing the rubber blade holdet teesessssssssscsssssss
7. TENANCE WORKING HOURS WORKING HOURS Repair all paint damages Check all bolt connections and hydraulic connections and tighten if required Check that there are no leakages in the hydraulic system If required tighten the connections of the hydraulic parts and hose ends Check the condition and fastening of the cutting edges If required adjust the cutting edges or replace them WWW MEIRENSNOW COM Check all bolt connections and hydraulic connections and tighten if required Grease all the grease points grease nipples on the cylinders horizontal and vertical pivot of the lift arms of the plough rear attachment of the plough and the skid shoe as well Check the condition and fastening of the cutting edges If required adjust the cutting edges or replace them Check all bolt connections and hydraulic connections and tighten if required Check that there are no leakages in the hydraulic system If required tighten the connections of the hydraulic parts and hose ends Spray the zinc coated parts hydraulic valves and hose ends with rust resistant wax Grease all grease points Also grease or wax the extended adjustment surfaces of the internal pipe of the wheel mechanism Check the plough visually and see if there are parts that need to be replaced Retract the piston rod of the cylinder and cover it with proper grease Store the plough in a place exposed to winds but protected from rain and UV ra
8. catcneco ss deacessateecuouatendendescaneosedencencateamsbamtendens 17 Drawing L6 Front SKA SNOG cerea E E T T T S E 18 Drawing 17 Rear slide foot when using the steel blades oo eee eeseeeeseseeseeeeseeeescsecsseesceeeaceeescseeaceeeasseeaseeees 19 Drawing 18 Rear slide foot when using the rubber blades ooo eee eeeseeceeeeeeceeeseeeceeeseeeceeeseeeesesaeeeeeeeaeeeseeeaeees 19 Drawing GSAS DOIN Srecan an a aves ee nea ale ts anaes alta aed 21 Drawing 20 Grease POINTS susricnnecie anan R E E T ae a 21 WWW MEIRENSNOW COM 3 CE DECLARATION OF CONFORMITY Manufacturer Meiren Engineering OU Vaike Manniku 7 11216 Tallinn Estonia Phone 372 682 5002 www meirensnow com We hereby declare that the below mentioned product Highway side wing snow plough MEIRER KSM3103 KSM37 03 Model Serial number Manufacturing date meets the following directives and standards 2006 42 EC EN 349 1993 A1 2008 WWW MEIRENSNOW COM SIDE WING PLOUGH KSM 03 SIDE WING PLOUGH KSM 03 FOREWORD Thank you for choosing this Meiren Snow product This user manual contains the technical specifications of the KSM snow plough series the product usage and maintenance instructions and the warranty terms and conditions The KSM snow plough series is designed for removal of loose snow from hard surface roads This product is not suitable for removal of sand gravel packed snow ice etc Inexpedient application of the snow plough can result in economic lo
9. ck nut WWW MEIRENSNOW COM 13 SIDE WING PLOUGH KSM 03 Drawing 9 Installation of the rubber blade holder Before installing the rubber blade holder be sure to remove the side blade holder with the side blade from the moldboard of the plough and the steel blade holder Drawing 3 positions 10 12 20 23 4 1 2 Replacing the rubber blade Release the bolts 6 Drawing 9 Remove the worn out rubber blade 4 Place a new rubber blade 4 between the blade holder 1 and the fastening plate 5 NB Length of the rubber blade should match with length of the blade holder Drawing 10 Table 3 Tighten the plate 5 against the rubber blade using bolts pos 6 tightening torque 60 70 Nm Locations of the side plough blades are shown in drawing 8 and lengths of the respective positions according to the plough models are described in table 3 Position on drawing 9 ene KsM3i03_ _KSM3703 po 954220 915 1220 w w Width of steel blades mm a a 1220 Width of rubber blades mm pot 915 1215 915 1215 915 1215 eis 1000 Table 3 Lengths of the side plough blades _in case of extension WWW MEIRENSNOW COM 14 SIDE WING PLOUGH KSM 03 Drawing 10 Location of the blades 4 1 3 Description and use of Hardox rubber blades Hardox rubber blades are highly durable rubber blades with Hardox metal reinforcement that withstand difficult conditions better than standard rubber blades and ensur
10. e significantly longer lifetime thanks to wear resistant metal Hardox blade is suitable for use instead of rubber blade with all snow ploughs Hardox rubber blade includes steel blade segments surrounded by rubber Hardox rubber blade can be used on both sides up to the red area marked on the blade If one side of the blade is worn out up to the red area turn the blade over and use the other side until it reaches the red area Hardox rubber blade wear must not exceed the red line i e 70 mm on both sides re Drawing 11 Hardox rubber blade 4 1 4 Fastening of the blade holder Place the rubber bushings 5 into the holes of the plough s moldboard 2 Drawing 12 Place the required 45 mm rubber strip 3 between the steel blade holder 1 and the plough s moldboard Press the steel bushings 6 through the rubber bushings 5 into the holes in the rubber strip Fasten the blade holder with bolt 4 by placing a conical washer under the bolt head Then screw a regular nut pos tightening torque 60 70 Nm on the steel bushing add a Nord Lock washer 8 and secure with a Nylock nut 9 Fasten the side blade holder together with the side blade Drawing 12 positions 10 12 20 23 NB Length of the steel blade 11 Drawing 12 must match with length of the blade holder Drawing 10 Table 3 WWW MEIRENSNOW COM 15 SIDE WING PLOUGH KSM 03 The steel blade holder is removed in the same way only i
11. ecessary backing If possible avoid snow ploughing in heavily loaded crossings and roads during peak hours All warning lights must always be switched on during working Each time there is an incident during operation that could damage the equipment an inspection of the equipment shall be arranged with the aim of detecting and evaluating possible damages Damages cracks in the structure or welded joints deformed parts may damage property and cause injuries It is forbidden to continue work until the damages are repaired Drawing 1 Safety marking RISK OF ACCIDENT WWW MEIRENSNOW COM 8 SIDE WING PLOUGH KSM 03 3 MOUNTING AND DEMOUNTING OF A PLOUGH Spring of the parallelogram 1 Drawing 2 must be tightened so that it prevents the lower arm 2 from sinking down under its own weight when it is not supported from the lift cylinder of the parallelogram 3 Purpose of the spring is to reduce the impact of the parallelogram s weight to the plough s moldboard The pin of the parallelogram s lift cylinder is only used by installing the plough to adjust the height of the parallelogram up down Always remove the pin before the operation to ensure the floating position of the plough in relation to the road surface First attach the support 5 with holder 8 to the moldboard of the plough 1 Drawing 3 3 and adjust so that the plough is raised from backside up from the ground When installing the plough to the vehicle must be drive
12. ed independently without acquiring a prior written approval from the seller the design is changed additional equipment and or spare parts have been installed independently without acquiring a prior written approval from the seller In the event that the seller despite repeated written appeal from the purchaser fails to fulfil its warranty obligations under the contract the purchaser shall have the right to repair the product at the cost of the seller The purchaser must notify the seller in writing at least 5 five business days prior to the replacement or repair of the defective product and provide a reasonable estimation of the expected cost The purchaser may withdraw from the contract and demand the collection of the product and refund only in the event that there is a defect which cannot be repaired or a part which cannot be replaced and the replacement of the defective product with a new product would also not give results which would allow using the product as intended The warranty for the product or its part replaced during the warranty period shall cover the product or its part until the end of the general warranty period WWW MEIRENSNOW COM 23
13. es too much the pressure relief valve opens In especially extreme cases when the above mentioned shock absorbers prove to be insufficient the bolts of the rear axle of the rotating hydraulic cylinder break and the cylinder moves back for a detailed description and a drawing refer to the section 4 in this manual In case of collision with an obstacle it is also possible that the bolts of the blade and the rubber bushings break 2 Drawing 9 and 4 5 Drawing 12 If there are only the parallelogram of the plough weight 386 kg and the rear attachment weight 160 kg without the moldboard on the vehicle chassis then the additional weight affecting the vehicle chassis is approx 546 kg Total width of cutting edges Blade holder for steel blades 3045 3350 3655 3960 mm Blade holder for rubber blades 3045 3350 3655 3960 Plough working width in max angle mm 2436 2923 Total width of the plough blade mm 3323 3650 3892 4195 Distance between the holes of the blade bolts mm 305 10 hole 11 hole 305 12 hole 13 hole Plough height with blades Blade holder for steel blades 987 1325 587 1455 mm Blade holder for rubber blades 676 1411 675 1543 Tilt angle of cutting edges in Blade holder for stee blades relation to the ground Blade holder for rubber blades 95 Plough weight in standard equipment kg 1010 1070 Table 1 Technical specification of the plough _In case of extension WWW MEIRENSNOW COM 6 SIDE WING P
14. ion speed of the plough in normal road conditions is up to 60 km h Follow the weather conditions when it is melting reduce the speed when the snow Is light pay attention to the wind direction and reduce the speed if necessary When working on soft ground reduce the speed since the cutting edges may cut in the surface and you may lose control of the truck or tractor and the vehicle may run off the road If the surface is soft support the plough with slide feet wheels or an additional blade The plough can only be used for removing loose snow It is forbidden to use the plough for removing ice frozen snowdrifts rock gravel sand and other similar material tis forbidden to remove the snow bank at maximum permitted full speed since this may damage the plough Itis forbidden to remove snow outside of road boundaries In the event the highway plough is used in the city or on uneven roads where there is a risk of damaging the plough vehicle or road surface the user shall bear sole responsibility for such an activity The manufacturer shall not be liable for any losses caused by the abovementioned activities It is forbidden to attach such additional equipment on the moving parts of the plough that are not approved by the manufacturer Itis forbidden to use hydraulically operating equipment as a lifting jack The plough may be lifted only from eye bolts ATTENTION Pay extra attention to when cleaning crossings Avoid unn
15. n parallel to the moldboard of the plough so the axle 3 Drawing 4 on the vehicle goes into the guides on the plough s moldboard At the same time should the plough s moldboard have about 10 angle from the vehicle Afterwards lock the upper guide with the respective pin 2 Drawing 4 Lock of the lower guide 4 Drawing 4 is locked with pin 7 into guide A Drawing 4 Then push out the shock absorber 2 Drawing 5 from the beam that is attached to the rear of the vehicle position the joint of the rotating hydraulic cylinder 1 axle 3 in the respective hole and lock it Remove the support 5 Drawing 3 3 Finally connect the quick couplings on the rotating hydraulic cylinder to the couplings on the rear beam Remove the pin of the lift cylinder 2 Drawing 6 and place it in the holder Always remove the pin before operation Drawing 2 Lifting frame WWW MEIRENSNOW COM 9 SIDE WING PLOUGH KSM 03 Drawing 3 Support for installing the plough s moldboard to the vehicle Drawing 4 Front attachment of the plough s moldboard WWW MEIRENSNOW COM 10 SIDE WING PLOUGH KSM 03 Drawing 5 Rear attachment The plough s removing is analogous to attaching only in reverse order However lock of the lower guide 4 Drawing 4 must be opened and locked with pin 7 into hole B When the plough is not in use the shock absorber 2 Drawing 5 in the rear beam should be pushed in the beam and locked with an axle
16. n reverse order Blade attaches to the blade holder in a standard way with wedge bolts or other bolts Cut the corners Drawing 4 pos 6 and Drawing 10 pos 1 of the front steel blade diagonally phase 60x45 or radius R50 IO CO V NS non 3 10 h 1 11 Drawing 12 Fastening of the blade holder Drawing 13 Installing the side blade 4 2 Adjusting the corner of the plough s moldboard The angles of the moldboard in relation to the horizontal surface can be adjusted as needed by adding or removing plastic plates 1 Drawing 14 between the moldboard of the plough and the pivot Use one plastic WWW MEIRENSNOW COM 16 SIDE WING PLOUGH KSM 03 plate by default It is also possible to adjust the arm with washers Drawing 5 The washers can be placed on the left or right side of the arm By default two washers are placed on the right side of the upper arm and one washer on both sides of the lower arm 1 Drawing 5 Position of the fastening plate 2 Drawing 8 can be adjusted as needed Drawing 15 Adjusting with washers WWW MEIRENSNOW COM 17 SIDE WING PLOUGH KSM 03 4 3 Using skid shoes Depending on the equipment the plough may be equipped with two skid shoes One can be attached to the moldboard rear skid shoe and one to the parallelogram front skid shoe When using the moldboard extension do not use the skid shoe attached to the parallelogram Both skid shoes can be used with steel blades
17. ng is allowed only by the soft snow A The cutting of frozen compacted snow or ice is not allowed because it can damage the plough Depending on the installation to the vehicle the plough s moldboard can be raised up to 335 400 mm from the ground by using the steel blades and 250 305 mm by using the rubber blades There is 53 angle in relation to the vehicle when the plough is in fully opened position Depending on the slope of road surface can the plough s moldboard angle be varied in relation to the ground from 2 to 1 During cutting the ridges of the snow piles the plough Is in the edge about 1 higher than normally Changing the angles of the snow plough in relation to the ground can be done by adding or removing the plastic sheets between the moldboard and the axle of rotation For protecting the snow plough and the frame of the vehicle even in extreme situations there are used different shock absorbers and protect mechanisms As the first shock absorber has the snow plough on the rear attachment of the rotating cylinder the rubber bushing which minimize the momentary shocks and noise as well Next protection is the hydraulic accumulator which guarantees the backward movement of the snow ploughs moldboard by serious obstacles If the pressure will be too high for hydraulic accumulator the pressure relief valve opens If the hydraulic battery proves to be insufficient and the pressure in the rotating hydraulic cylinder increas
18. re already frozen Operation with steel blades requires the blade holders which ensures that the blades have a 40 angle in relation to the ground Operation with rubber blades requires a blade holders which ensures that the blades have a 95 angle in relation to the ground Rubber blade holders have a rubber quick attachment system There is no need to drill holes through the rubber and it speeds up the installation and replacing the rubber refer to section 4 1 Rubber blade holders makes possible the rubber blade and the steel blade using at the same time In this case the steel blades can be installed in front of the rubber blade For this purpose the rubber blade holders include wedge bolt openings There is a45 mm thick rubber strip between the steel blade holder and the moldboard that reduces noise and makes the response of the blades more flexible by harmonizing pressure of the blades to the road surface Blades are fastened to the blade holders in a standard way with wedge bolts There are support plates under the blade holders to reduce its wear upon excessive wear of the blades When the side plough collides with an obstacle the primary blow is dampened by the hydraulic battery and the safety valve If the impact is too strong then bolts 1 Drawing 7 of the rear axle of the rotating hydraulic cylinder may also break In this case the cylinder moves back through the fastening hole and the plough can move back freely When the bolts of the
19. rear axle break the hydraulic hoses may break as well Bolts are strength grade 10 9 regular bolts and must be replaced afterwards It is important to remember to use Nord Lock washers 2 Drawing 7 when replacing the bolts Drawing 7 Rear attachment of the rotating hydraulic cylinder WWW MEIRENSNOW COM 12 SIDE WING PLOUGH KSM 03 In travelling position the plough must be locked with the fastening plate 2 Drawing 8 to the joint 1 Position of the fastening plate is adjustable as needed by using additional holes in the plate NN S Drawing 8 Locking the plough in travelling position 4 1 Replacing the blade holders Different blades must be used in different weather conditions In early winter when the ground is not frozen the rubber blades should be used for snow clearing from road shoulders In that case the plough s moldboard does not dig into the ground When the ground is already frozen and there is compressed snow on the sides of the road steel blades should be used for snow clearing 4 1 1 Removing and installing the rubber blade holder To remove the rubber blade holder release the bolted joint 2 Drawing 9 Remove the blade holder with the rubber blade fastening plate and bushings Drawing 9 positions 1 4 5and 3 The rubber blade holder is installed in the same way only in reverse order When fastening the bolt joint 2 Drawing 9 remember to use Nord Lock washers under the bolt head as well as the Nylo
20. scsssssssssssscssssscssssssssssssssssssssssses 13 AS BOINE NETIBOLI O rnEeE E O A EO OO O O en vosten 14 4 1 3 Description and use of Hardox rubber DIGGS iaceianiaiacsite les ceteeaaseacaeteas peotuasaila Gasauestesiiemieenetaat 15 ALA Fann OF NE LAGE NOTO nE EEEE E EE E O N E Sahat aioe 15 Ale ADJUSTING THE CORNER OFTHE PLOUGH S MOLDBOARD sisscisinpiecroieicsn aites nei a a aa atai 16 A USINGSKID SHOE Sarine ena A E A N N teas 18 A Ide USIP SKIG SINOC ONION DLO SD aI EEEE AEREE OU T O 18 LIe USINE SNORO IMI r UT iir EE A AAT 18 bs MAINTENANCE OFTHE SNOW PLOUGH ioooceiccscscsccicccsti cca ccstiteaetet scatds ES 20 Se ASE ie ONES ca aie a A tie each ca 21 6 WARRANTY CONDITIONS OF THE PRODUCT iisicccscccsccscetsvecectcdvcnecoctieesidciiesdstaueiashcavaneeiiseetdddeerdeeiwaneaet 23 TABLES Tabled Technic alrSpec iN atiONniOIMne DIOUON s itnccesscztenohtuascnca sted saleustesrap a E a 6 Table z Hydraulics On Te OlOU duemen a E A ocesemucneascews ved E otesemecne wanes Aeegttocor reece lables Lenoths Or the SIdeplOUGMD AGES inia aien alah aie eetamieicas 14 Papier IS COP ChEaS ePOS mcii tanan e E E E E ohare satus naue east 22 DRAWINGS Drawing 1 Safetymarking RISKOF ACCIDENTI six ctscraces ti iatte tse cateels e a bit wiatendar th AR 8 Drawine LNG Ti aC as tesccet aes Geet a eRe Se tava ted leah Aa a an te wei cnd esata diet aa eased 9 Drawing 3 Support for installing the plough s moldboard to the vehicle s s sssesesesesesesesesesesesesrsr
21. sesrsesesesesesesess 10 Drawing 4 Front attachment of the plough S moldboard s s s sesesesesesesesrsesrsrsrsesrsrsrsrsrsrsrsrsrsrsrsrsrsrsrsrsrsrsesrsesesene 10 Drawings Rearatachinen tenir R 11 BDrawine 6aPn OFRENE CUING narei E E east souates TI WWW MEIRENSNOW COM 2 SIDE WING PLOUGH KSM 03 Drawing 7 Rear attachment of the rotating hydraulic cylinder ee eee teeeeseeeeeeeeeeceeeseeeceeeseeeeseeaeeeeseeeeeaeeeeeeees 12 Drawing 8 Locking the plough in travelling POSITION eee eeseeeeteeeeseeeeseeeeseeescecscseescseescseesceeeaceeeasseeasseeaeeeees 13 Drawing 9 Installation of the rubber blade holder ssssssessssesssessssssssesrssssssesesrsrsrssssesesrstsrssesestsrsrsreteresesesrsreresess 14 Drawing 10 Location of the blades snaccass aeacncessvacenss detswaapeinateagecetceace uatiecesdedseaapenasiecap det caasaouatiesandetsonapetatecasdeasecessuetecesee 15 Drawa TE TARO OX FUDD TAG naese ccm acee se teas eae et Rare cash actin ed sem test eee are cash elie um test ieee ace at eet ey 15 Drawing te Fastening ofthe blade Nolde ensarinaroniianicanii a a 16 Drawing 13 Installing the side blade essenssssssessssssesesrssssssssrsrsrssesssesrsrstssesesesrstststeseststsrsrstesesestsrsretetesesesesrsreresess 16 Drawing 14 Adjusting the corner of the plough s moldboard sssssssssessssssssesesesesesssessesesesesesessesesesesesssseseseseseseses 1 Drawing 15 Adjusting with washers odes dccesicsaconaicadendancamepsedencencsteectonatenden
22. sses and cause human bodily harm That is why it is essential for the person operating the snow plough to read the manual carefully and use the product in compliance with the stipulated requirements Any misuse of the product shall release the manufacturer from liability to compensate for resulting damage and losses GENERAL SAFETY REQUIREMENTS As the construction of the product is complex and it contains moving parts it is of the utmost importance that the person working with the equipment be aware of all safety risks To reduce the risks It is important that the operator have read through the operator manual the operator have been given an appropriate training which gives him the permit to use a product of this type in his work the operator have been provided with all necessary tools and is wearing suitable working clothes PERSONNEL This product may only be used and maintained by properly trained personnel The operator s employer is obliged to ensure fulfilment of all user instructions and safety requirements stipulated by the manufacturer Before starting working with the plough please read carefully through the operator s manual WWW MEIRENSNOW COM 5 SIDE WING PLOUGH KSM 03 1 PRODUCT DESCRIPTION The KSM side wing snow plough has durable construction Using this plough makes possible to substantially enlarge the working width as well as clean the snow on road shoulders by cutting the ridges of the snow piles The cutti
23. ys 20 SIDE WING PLOUGH KSM 03 5 1 Grease points MN i p a a Si Drawing 19 Grease points d j 7 f i Tih eo Da N NS Drawing 20 Grease points 21 WWW MEIRENSNOW COM WWW MEIRENSNOW COM Pos no Location of grease points Ouantty i Brotketofrearae 4 2 Pvoteyinder a 3 ea a 4 Lawerleverofparaletogam 4 e ee ee Oe Upper lever of paralellogram a Lifting cylinder lt a ng Ca T aum In all Table 4 List of grease points SIDE WING PLOUGH KSM 03 22 SIDE WING PLOUGH KSM 03 6 WARRANTY CONDITIONS OF THE PRODUCT The seller shall give the product a warranty period of 12 twelve months The warranty period shall begin when the product is transferred to the purchaser the delivery time shall be the date specified on the instrument of delivery and receipt or the CMR consignment note The warranty shall cover the elimination of discovered manufacturing material or structural defects of the product by the seller The seller shall be obligated to replace the defective product with a new one only if the product or its component parts cannot be repaired or the detail cannot be replaced The purchaser shall agree to notify the seller in writing within 7 seven calendar days of becoming aware of the defect describing the defect with sufficient accuracy The seller shall be required to carry out an expert analysis to identify the causes of the defect within
Download Pdf Manuals
Related Search