GARDEN CULTIVATOR - Lidl Service Website
Contents
1. soil for the purpose of mixing in ferti liser peat and compost in domestic areas Any use other than that specifically named in this manual may lead to damage to the tool and represents a serious injury hazard for the operator The operator or user of the tool is responsible for any damage or injury caused to other per sons or property This tool is intended for use by adults Chil dren and persons unfamiliar with the manual must not be allowed to use the tool Do not use the tool in rain or damp surroundings The manufacturer shall not be held liable for damage arising from improper use or incor rect operation of the tool Flora Best 7 GB CIE CY Assembly instructions Always disconnect the tool from the mains before conducting any work on it Scope of delivery Carefully remove the tool from the packaging and check that the following parts are com plete e Motor housing with tines and frame tubing e Right hand fork with dead man lever and permanently fixed mains cable e Left hand fork grip e Plastic cross plate with cable guide e Assembly tools cable clips and belt clip e User manual While assembling the tool make sure that the mains cable does not become caught and has enough slack Fitting the grip tubing 1 Push the two fork grips 1a 1b into the plastic cross plate 3 and screw the plate into the corresponding holes in the grip tubing from behind using the bolts provided 13 2 Push t2. GARDENA CULTIVATOR L FGH700 9 k CED E GARDEN CULTIVATOR Operation and Safety Notes ie RR a GB CE CM Before reading unfold the page containing the illustrations and familiarise yourself with all functions of th device GB IE CY Operation and Safety Notes GB CIE CY User manual FGH 700 9 Electric Tiller Contents Safety A 4 Symbols eee 4 General safety notes 5 Functional description 7 Functional palts aid 7 Intended purpose ee 7 Assembly instructions 8 Scope of delivery pp 8 Fitting the grip tubing pp 8 Op ration 2 2 8 Switching on and off 8 Operating instructions 8 Cleaning maintenance storage 9 General cleaning and maintenance work 9 Changing the tines 4 9 STOJE anne ee ee TCA 10 Guarantee siii 10 Replacement parts pp 11 Disposal environmental protection 11 Technical specifications 11 EC Declaration of Conformity 12 Exploded diagram pp 13 Grizzly Service Center 14 Before first using the machine please read this instruction manual carefully for your own safety and for the safety of others Keep the manual in a safe place and pass it on to any subse quent owner to ensure that the infor mation contained the
3. careful while moving backwards danger of tripping over e Do not use the tool if it is damaged in complete or altered without the approval of the manufacturer In particular do not work with the tool if guards or protection fittings are damaged or missing e Do not overload the tool Only work in the performance range stated Do not use tools that do not have sufficient power for heavy jobs Do not use the tool for any use other than that intended by the manu facturer e Avoid damage to the tool Do not apply extra weight and do not drag the tool over hard surfaces such as tiles or steps Stopping work Warning The tines will continue to turn for a few seconds after you switch the tool off Wait until they have stopped moving injury hazard e Do not lift or transport the tool while the motor is running Turn the tool off and wait for the tines to stop moving then disconnect the tool from the mains before changing the area you are working on e Never leave the tool unattended where you were using it Switch the tool off wait for the tines to stop moving and disconnect the tool from the mains under the following circum stances Always before leaving the tool Before removing remnants of soil and plants When the tool is not in use Before you conduct maintenance or cleaning work on the tool If the mains cable is damaged or caught up If the tool collides with an obstacle or starts to vibrate in a
4. ead to loss of guarantee Working with the tool Keep your hands and feet away from the tines while working especially when starting up the tool injury haz ard Observe any noise prevention regulations and local by laws Using the tool may be limited or prohibited on certain days such as Sundays or public holidays or during certain times of the day midday at night or in certain areas such as at health spas and hospitals Do not use the tool to chop up stones or till lawn soil as such use may damage the tool Do not use the tool in rain foul weather or damp surroundings such as near garden ponds or swimming pools Only use in daylight or good lighting conditions Be sensible Do not use the tool if you are tired or easily distracted or after the use of alcohol or medicines Take a break as soon as you need one Make sure that you are standing firmly when using the tool especially on slopes Flora Best 5 GB CIE CY If working on a slope work along the slope not upwards or downwards Be particularly careful when changing direc tion on the slope Do not use the tool on excessively steep slopes e If there is any danger of slipping on sloped ground have a second person secure the tool with a rod or cable The second person should stand up the slope at a safe distance from the tool e Always hold the tool securely in both hands while working with it e Make sure that the grips are dry and clean Be
5. ectrical appliances in household waste GB CIE CY Technical specifications FGH 700 9 Electric Tiller Motor power input 710 W Mains voltage 230V AC Mains freQUEnNcy n 50 Hz Working width oo 360 mm Max working depth 180 mm Number of tine wheeElS 4 Nominal rotation rate Approx 230 rpm Weight pirelli 7 85 kg Sound pressure level 69 3 dB A Guaranteed sound power level 93 dB A Vibration at hand grip 2 66 m s Noise and vibration values have been deter mined according to the standards and regula tions named in the declaration of conformity Technical and optical alterations may be made without notice for the purposes of improve ment No guarantee can be given for the ac curacy of dimensions notices and specifica tions stated in this manual The manufacturer shall therefore not accept liability for statutory claims arising from the manual Flora Best 11 EU declaration of conformity We hereby confirm that the FGH 700 9 series electric tiller conforms with the following applicable relevant version of the EU guidelines as of model year 2008 98 37 EC 2004 108 EC 2006 95 EC 2000 14EC In order to guarantee consistency the following harmonised standards as well as national standards and s
6. eet The tines may cause an accident Be careful while moving backwards danger of tripping Do not touch the gearbox as it may become hot during operation dan ger of burns 8 Flora Best To avoid damage to the tool e Never lift or drag the tool with the mo tor running Lift the tool while moving it over hard surfaces such as tiles or steps Switch the tool off after working with it and for transport disconnect from the mains and wait for the tines to stop moving e Walk the tool through the soil at nor A mal pace and in a line as straight as possible e Always work away from the mains socket Make sure that the cable is kept well away from the working area Hanging the cable into the belt clip included in the package will help e Overload protection The motor will cut out immediately if overloaded The tool cannot be used until it has completely cooled down again Cleaning maintenance storage Warning Always return the tool to the service centre for work not described in the manual Only use original parts Switch the tool off unplug it from the mains and wait for the tines to stop moving before carrying out any mainte nance or cleaning work on the tool en Perform regular maintenance and cleaning on the tool This will ensure long reliable service General cleaning and maintenance work Do not spray the tool down with water especially not under pressure and do not clean it unde
7. ent owner to ensure that the information it contains is al ways available Please read the following safety guide lines in order to avoid risk of fire electric shock personal injury and damage to objects Preparation For safety reasons do not allow children or young people under 16 or anyone not familiarised with this instruction manual to use the tool Never use the tool while others especially children or pets are close by Familiarise yourself with handling the tool and pay attention to all possible dangers that may be overheard while working with the tool Check the terrain on which you will be us ing the tool and remove stones sticks wires or other foreign objects that may be caught up and spun off Wear proper working clothes such as firm GB CIE CY footwear with non slip soles and strong long trousers Do not use the tool barefoot or wearing open toed sandals To prevent injury from the tines only switch the tool on in its working position Examine the tool beforehand every time you use it Do not use the tool when the safety components such as the power safety catch or guard cutting parts or bolts are missing worn or damaged In particular check the mains cable and dead man lever for damage Only replace damaged bolts or tines in complete sets to prevent imbalance Only use replacement and accessory parts delivered and recommended by the manufacturer Using foreign parts will im mediately l
8. he mains cable into the cable guide 14 on the cross plate 3 Position the assembled grip frame with the tube ends on the left and right hand sides at the lower frame tubing 5 4 Push the two finger bolts into the holes from the outside inwards and tighten them with the wing nuts 4 5 Fasten the mains cable with the cable clips supplied Large cable clip 6a above the cross plate Small cable clip 6b at the frame tubing Operation Observe noise abatement laws and lo cal by laws Switching on and off Note Before switching the tool on make sure that the tool is not touch ing any other objects and hold it firmly in both hands 1 Plug the tool into the extension cable 2 Loop the end of the extension cable and hang it onto the cable tension relief 16 to ease the tension on the cable 3 Plug the tool into the mains 4 Hang the extension cable onto the belt clip 12 and fasten it to your trouser belt 5 To switch on press the safety release catch 17 and then squeeze the dead man lever 18 Release the safety release catch 17 The tines will begin to rotate and dig themselves into the earth 6 To switch off release the dead man lever 18 Warning The tines will continue to turn for a few seconds after the tool has been switched off Do not touch the rotating tines injury hazard Operating instructions Always keep a firm grip on the tool with booth hands and watch your f
9. n unusual manner In this case examine the tool for dam age and have it repaired if necessary Use the tool away from flammable fluids or gases Failure to do so may result in fire or explosion Maintenance and storage Make sure that all nuts bolts and screws are tight and that the tool is in safe work ing order Do not attempt to repair the tool yourself unless you are qualified to do so Return the tool to our service centre to carry out any work not listed in the user manual Keep the tool in a dry place out of chil dren s reach Be careful in handling the tool Keep the tines sharp and clean to improve its work ing safety and effectiveness Follow the maintenance regulations Electrical safety Warning Do not use the tool if the mains or extension cable is damaged danger of electrical shock Keep the mains cable away from the tines Always trail the mains cable behind you or the person operating the tool If the cable becomes damaged during use im mediately disconnect it from the mains Never touch the mains cable before un 6 Flora Best plugging it from the mains e Make sure that the mains voltage match es the data on the tool s rating label e If possible connect the tool to a socket with a residual current RC trip switch at a triggering current of not more than 30 mA e Avoid skin contact with earthed objects such as metal fences and posts e Make sure that the connector on the ex tensi
10. on cable is protected from splash water and is made of rubber or has a rub ber covering Only use extension cables that are intended for outdoor use and are labelled as such Use extension cables with a cable core diameter of at least one square millimetre Always completely un wind the cable reel before use Check the cable for damage e Use the cable hanger fitted for the pur pose when using an extension cable e Do not carry the tool by the cable Do not unplug the cable by tugging on it Keep the cable away from heat oil and sharp edges Functional description Your hand operated garden tiller is equipped with a maintenance free electric motor and a gearbox with sump lubrication The tool is fitted with four rotating tine wheels that automatically dig themselves into the ground The aluminium frame can be folded to aid storage Please refer to the following descriptions for the function of the controls The major functional parts are shown on the foldout page GB CIE CY Functional parts 1a Right hand fork grip with dead man lever safety release catch and cable tension relief Left hand fork grip Mains cable Plastic cross plate Wing nuts and bolts for securing the grips 5 Frame tubing 6a Large cable clip 6b Small cable clip 7 Vent 8 Motor housing 9 Gearbox 10 Driveshaft 11 Tines 12 Belt clip ON oO Intended purpose The tool is intended for breaking up and tilling coarse
11. or improper use is not covered by guarantee Certain components are sub ject to normal wear and are not covered by guarantee Such components particu larly include tines e Guarantee service is also conditional upon compliance with cleaning and main tenance instructions Any damage caused by faults in materials or manufacturing shall be remedied by free repair or replacement e You may have repairs not covered by guarantee carried out for a charge at our service centre Our service centre will be pleased to supply you with a cost esti mate We can only process orders on tools sent in with adequate postage and packing e Tools sent in by express measurement cargo or other special forms of post age with freight collect will be refused e We will dispose of tools free of charge Replacement parts Use the service address or fax number sup plied to order replacement parts Make sure you include the order number in your order Set of tines Right left Order No 30261000 Please contact our service address for all other replacement part numbers Disposal environmental protection Be environmentally friendly Return the tool accessories and packaging to a recycling cen tre when you have finished with them amp Return the tool to a recycling centre The plastic and metal parts used can be separated and sorted for recycling Ask our service cen tre for details Do not dispose of el
12. r running water GB CIE CY Wear protective gloves when carrying out maintenance and cleaning work on the tool to avoid injury from cuts Always clean the tool thoroughly after each use Always keep the tool clean Do not use cleaning fluids or solvents e Remove any soil and dirt residues stuck to the tines driveshaft tool surface and vents with a brush or dry cloth e Spray or rub biodegradable oil into the tines e Clean soiled grips with a damp cloth e Always check the tool for obvious damage such as loose worn or damaged parts before using it Check that all nuts bolts and screws are tight e Check the covers and guards for damage and correct fit Change them if necessary We shall not be held responsible for any dam age caused in any of the following ways Improper repair Use of non original parts Use other than for the intended purpose Changing the tines The tool is fitted with four tine wheels that can easily be changed in pairs Both of the tine wheel pairs can be fitted on the left or right as required Always change both tine pairs at the same time to avoid damage to the tool from imbalance Switch the tool off unplug it and wait for the tines to stop turning 1 Lay the tool on the ground with the rating label facing upwards 2 Unscrew the hex bolt 19 and the self locking nut 20 on the tine wheel pair 11 Flora Best 9 GB CIE CY 3 Slide the tine wheel pair off
13. rein is available at all times im Safety notes This section deals with the basic safety regu lations while working with the electric tiller Symbols Symbols on the tool A AG Danger of injury from objects spin ning off Keep surrounding persons away form the hazard area Warning Read the user manual Warning Protect from rain and damp Warning Switch off the tool and disconnect it from the mains before carrying out any cleaning or mainte nance work Danger from damaged mains cable f Keep mains cables away from tines Qe A Danger of injury from rotating parts The tines will continue to rotate after amp the tool has been switched off Wait for them to stop moving 9 Sound power level L in dB dB E Safety class Il a Do not dispose of electrical equipment in household waste 4 Flora Best Symbols in the manual Warning symbols with information on damage and injury prevention Instruction symbols the instruction is explained at the place of the exclama tion mark with information on preventing damage Help symbols with information on im proving tool handling General safety notes may lead to serious injury Read this Warning Improper use of this tool instruction manual carefully before you start working with the tool and famil larise yourself with its controls Keep the manual in a safe place and pass it on to any subsequ
14. the shaft 10 4 Clean the driveshaft with biological oil 5 Slide the new tines onto the drive shaft with the holes on the axles aligned to the holes on the driveshaft 21 Make sure that the tines are set to their proper turning direction The arrows on the gearbox and tines should point the same way No 22 6 Slide the hex bolt through the hole and tighten on the self locking nut Supplied with each new tine wheel pair 23 Storage e Leave the motor to cool down before you put the tool into a closed space e Keep the tool clean dry and out of the reach of children Unscrew the wing nuts No 4 and fold the fork grips down to reduce the space taken by the tool Make sure that the ca ble does not become jammed e The frame tubing No 5 also serves as a hook to hang up the tool at the place of storage e Do not cover the tool in plastic bags as moisture may form Do not use the tool with the handle folded closed Guarantee e This tool is subject to a guarantee period of thirty six months A shorter guarantee period of 12 months shall apply for com mercially used and replacement tools ac cording to statutory regulations If you have a justified guarantee claim please contact us at our service cen tre see last page for our telephone number fax number and e mail ad dress We will then give you the de tails on the claims procedure e Damage caused by natural wear over load
15. tipulations have been applied EN 709 A1 1999 EN 60335 1 A2 2006 EN 50366 A1 2006 EN 55014 1 A2 2002 EN 55014 2 A1 2001 EN 61000 3 2 A2 2005 EN 61000 3 3 A2 2005 We additionally confirm the following in accordance with the 2000 14 EC emissions guideline Guaranteed sound power level 93 0 dB A Measured sound power level 89 3 dB A Compliance evaluation process carried out in accordance with Appendix V 2000 14 EC Labelled with CE identification mark in 2008 Responsible for product manufacture and technical documentation safekeeping x x 7 x x Grizzly Gartengerate GmbH 8 Co KG u Am Gewerbepark 2 A y MU D 64823 GroB Umstadt 12 11 08 ie Andreas Gr schl Techn director i 13 20 ep ll T Ci f Exploded diagram 7 q Y qe TA Y gt Grizzly Service Center GB 14 DES Ltd Unit 14 15 Bilston Industrial Estate Oxford Street Bilston WV14 7EG Tel 0870 787 6177 Fax 0870 7876168 Email grizzly deslimited com From Ireland Tel 0044 870 787 6177 Fax 0044 870 787 6168 Flora Best Flora Best IAN 41803 Grizzly Gartenger te GmbH amp Co KG Am Gewerbepark 2 D 64823 Grof Umstadt Last Information Update 11 2008 Ident No 76005517 112008 6
Download Pdf Manuals
Related Search