® CUTE - PLS Electronics
Contents
1. n a 15 pe ee ee en Cen Cree Cra n a Item number 5e One to which this declaration relates is in conformity with the following standards e EN 55015 1 Electromagnetic compatibility Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment CISPR 15 2000 CISPR 15 2000 A1 2001 CISPR 15 2000 A2 2003 e EN 61000 6 2 Immunity for industrial environments e EN 60439 1 Low voltage switchgear and controlgear assemblies Part 1 Type tested and partially type tested assemblies Therefore the upper indicated product qualifies the EU 73 23 EWG LV directive and the 89 33 EWG EMC directive considering 93 465 EWG directive for CE Place of issue Signature of authorised person Szekesfehervar HUNGARY Date of issue 01 03 2014 j Meee Vass Managing Director of PLS Ltd 15 Notes PLS Kft H 8000 Szekesfehervar G zmalom utca 22 HUNGARY Tel 36 22 789 589 Fax 36 22 382 783 E Mail info pls huWeb www pls hu2. L2 or 5 Brown Line 3 L3 or T Blue NEUTRAL N Green Yellow Protect Earth PE CAUTION The manufacturer doesn t responsible if the installer user connect the cable wrongly The guaranty will be void if the connection order is wrong and the unit can damage too Before power up always control the right connection of the Lines Neutral and the Protect Earth The unit is able to control 12 x 16Amps The input L1 L2 and L3 lines are connected to the channels as the follow 1 4 channel to Phase L1 5 8 channel to Phase L2 9 12 channel to Phase L3 You can use the unit from two or one phase too for example the L1 and L2 are the same phase If change the numbers of phases the maximum output power is change like this At 3 phases 3 x 63Amps at 2 phases 2 x 63Amps at 1 phase 1 x 63Amps These are the absolute maximum ratings A If you overdrive the dimmer can DAMAGE A PEGASUS CUTE Digital Dimmer Mains distro 4 Digital Control 4 1 DMX input The DMX input signal must be connect to the DMX In marked connector which can be found on the front side of the unit Pin Function Pin 1 Pind Pin Number Pin Pin 4 1 Ground Shield nd a ne PUS n Spare Data NC Pin 5 Pinl Pin Spare Data NC Pin 4 Pin 2 Mi a Pin 1 Pin 37 Pin 3 Table 1 Functions of XLR pins Figure 5 Outlet of the connectors front view the male connectors in the upper line The DMX input of the dimmer is power and opto i
3. stored data is present on the outputs of the dimmer and you can edit it With the UP DOWN keys select the output and press SET to change the value of that output Press the SET to store the set value or press ESC to exit without saving from this menu point Repeat the steps above to adjust the other channels if necessary If the selected memory location is not empty the dimmer prompt you that the location is contain stored data Press Ok to accept it and you overwrite the existing data or press ESC to choose another location 4 2 8 3 Record Memories With this feature you can store DMX data into the memory Use the UP DOWN keys to select memory location where you want to save the DMX input and press SET If the selected memory location is not empty the dimmer prompt you that the location is contain stored data Press Ok to accept it and you overwrite the existing data or press ESC to choose another location 11 PEGASUS CUTE Digital Dimmer Mains distro 4 2 8 4 Priority of Memories If you want to add the DMX input data with the memory at playing chose with the UP DOWN keys the HTP highest takes precedence Otherwise select No DMX to disable the DMxX input while memory playing is in progress 4 2 9 If DMX Fails Here you can set how the dimmer react if the DMX signal is fails You can choose from the following possibilities 1 Keep DMX value the dimmer keep the output levels infinitely till a new valid DMX pocket no
4. E LEE Figure 3 Back part connectors 1 DIMMER Outputs for the channels 1 to 6 This connector referred in the future as Socket A These outputs are coming from the dimmer circuits 2 DIMMER Outputs for the channels 7 to 12 This connector referred in the future as Socket B These outputs are coming from the dimmer circuits 3 HOT POWER Outputs for the channels 1 to 6 This connector referred in the future as Socket C These outputs are coming directly after the corresponding MCB 4 HOT POWER Outputs for the channels 7 to 12 This connector referred in the future as Socket D These outputs are coming directly after the corresponding MCB 5 AUX output 230V 16A protected by RCBO 6 Mains input via H07 5G10 rubber cable The pin outlet the 16 pole Harting type connectors in H version are the follows Pin number Function Output phases for channel 1 2 3 4 5 6 respectively at Socket A amp C 1 2 3 4 5 6 and output phases for channel 7 8 9 10 11 12 respectively on the Socket B amp D Output neutrals for channel 1 2 3 4 5 6 respectively at Socket A amp C 9 10 11 12 13 14 and output neutrals for channel 7 8 9 10 11 12 respectively on the Socket B amp D 7 8 15 16 and the PROTECTIVE EARTH PE side connectors PLS Kft www pls hu The pin outlet of the 16 pole Harting type connectors in HD version are the follows Pin number Function Output phases for channel 1 2 3 4 5 6 respectively at Socket A am
5. PEGASUS CUTE 12 channel Digital Dimmer Mains Distributor User s manual First edition Copyright 2014 PEGASUS CUTE Digital Dimmer Mains distro Dear Customer Thank you for chose PLS Electronics product If you have any technical question or you looking for other equipments don t hesitate to take up the contact with our sales representative ot with the manufacturer at the www pls hu web site This apparatus is a twelve channel digital dimmer mains distributor with DMX 512 1990 with a lot additional control possibilities The light control is produced by a phase angle control technology at the dimmer outputs The hot power outputs are fixed lines from the MCBs Safety first Please read carefully and understand the user manual The wrapper of the unit is NOT baby toy Keep it away form babies For technical questions and original spare patts please take up the contact with our sales representative or with the manufacturer at the www pls hu web site ATTENTION A DON T USE WITHOUT PROTECTIVE GROUND A Not allowed to make a parallel connection between any outputs phases or neutrals to increase the output current capability of the unit Otherwise the unit can be damaged CAUTION A Do not cover any air inlets and fan outlets of the dimmer A Take care to have proper airflow in and out to let cooling the unit CAUTION Disconnect mains before open the dimmer for service Service allowed only for tec
6. each 1sec or steady the output in stable Press SET for selection and now you can select with UP DOWN keys which channel you want to test from 1 to 12 Press SET to modify the light output level by the UP DOWN keys to choose another output press SET again Press ESC to exit from this menu 4 2 3 Chaser The dimmer has 9 preprogrammed non modify able scenes chaser effects After enter to this menu select with the UP DOWN keys which chaser you want to play on the output The first three are fix light outputs 30 60 and 100 for each channel the last 6 are running chasers Press SET after selection and the chaser now present on the outputs To modify the light level grand master use the UP DOWN keys To select another chaser press SET to exit from the menu press ESC 4 2 4 DMX Softpatch You can select different DMX addresses for each output in this menu First with the UP DOWN keys select the output after press the SET and now select the DMX address for that channel Press the SET to chose another output and repeat the steps described before To exit from this menu press the ESC Here the dimmer asks back to enable this settings If you want to enable press SET otherwise ESC If you choose SET the global DMX address which selected in the first menu point is now disabled If you select ESC the selected addresses are stored but not enabled the global DMX address is enabled PEGASUS CUTE Digital Dimmer Mains distr
7. ect different control curves for each output enter into this menu point With the UP DOWN keys select the output and after press SET Now you can set the control curve by the UP DOWN keys A star indicated next to the level that the data has been changed Press SET and the level will be stored into the memory and you can select another output or press ESC to exit from this menu without saving you modification If you press ESC after pressing the SET you don t want to adjust more channels the dimmer stores the data and exit from the menu The factory default is RMS Linear for each output 10 PLS Kft www pls hu 4 2 8 Memories Here you can play record and edit dimmer scenes up to 16 memories After enter with the UP DOWN keys select which function you want to enter 4 2 8 1 Play Memories With the UP DOWN keys select a memory what you want to play and press SET With the selected Fade In time the dimmer starts to fade display the memory By pressing the ESC you can fade back from the memory If the HTP is selected in the PRIORITY menu point see three sections later the dimmer continues receiving DMX signal and handle the memory in Highest Takes Precedence priority Otherwise the DMX data recetving is disabled but the LED on the front panel still indicate that the DMX is present or not 4 2 8 2 Edit Memories With the UP DOWN keys select the memory location what you want to edit and press SET After it the
8. esponding MCB 5 AUX output 230V 16A protected by RCBO 6 Mains input via H07 5G10 rubber cable The pin outlet the 19 pole Socapex type connectors is the follows Pin number Function Output phases for channel 1 2 3 4 5 6 respectively at Socket A amp C 1 3 5 7 9 11 and output phases for channel 7 8 9 10 11 12 respectively on the Socket B amp D Output neutrals for channel 1 2 3 4 5 6 respectively at Socket A amp C 2 4 6 8 10 12 and output neutrals for channel 7 8 9 10 11 12 respectively on the Socket B amp D 13 14 15 16 17 18 10 PROTECTIVE EARTH PE Recommended male plug optionally orderable form PLS Male inline plug P19 LM S M40A solderable for cable OD 16 28mm 2 Installation of the unit After unpacking the apparatus is ready for use Not to make the cable longer If it is short use standard extension Operating with injured cable is perilous CAUTION The apparatus is NOT waterproof Protect it from liquids Not to use outdoors without appropriate preventive measures If water or other liquid getting into it dry up and take to technician Working with wet apparatus is PERILOUS The unit has been shipped with 5x10mm H07 rubber cable without CEE male plug except CUTE SX R and CUTE H R where the unit supplied with rack and CEE plug The correct order of the power cable is the follows PLS Kft www pls hu Cable color Function Grey Line 1 L1 or R Black Line 2
9. ghting time the lighting time can be infinitely or can Here you can specify the Fade In and Fade Out times for the memory play back Technical information 1 User Control Curve freedom for special control cases 2 If DMX Fails setup point 3 Display Time be switch off after a specified time 4 Memory Fade Times Power SUP anainn AN Power draw with open outputs eee OHIDOPCONMMECIOE re Ru Rae Input output data connectors sss N OSE R ES eet tent wo 2 Output protection ER RRR ee TN S 3x230V 400VAC 10 3 x 40A or 3x 63A 10W 4x 16 pole Harting H 4x 19 pole Socapex SX 5 pole XLR male females Amphenol made Toroidal filters at all ch tr 100uS 5 C16 Amps circuit breakers Hager liput BTOC RS A mue ee TVS and opto and power isolation on DMX Operatno t mbetat l Rent LOLA GS TEM POLAT Cs sn e Eiaa ne DIMENSIONS cccccccesccecceccceccecceccceceececcccsceesesceecs input outputs 10 C to 35 C 10 C to 60 C 484 x 132 x 350 connectors 15 PEGASUS CUTE Digital Dimmer Mains distro Notes 14 PLS Kft www pls hu CE We PLS Electronics Limited declare under sole responsibility that the product Declaration of Conformity Product name ennenen a rame Pegasus CUTE 12 x 3 7KW dimmer Product model output variations H2 4 x 16 pole Harting SX 4 x 19 pole Socapex Serial Number
10. hnicians who had technical course by the sales representative or by the manufacturer 9 12 11 10 13 Bi a3 ID HAGER Y HAGER Ci CWA Figure 1 Handling units of front part PLS Kft www pls hu Front parts 1 AUX Output RCBO protector combined MCB RCD 30mA 2 These green LEDs show the control level of each channel 3 Output protector MCBs C16A which protects the corresponding dimmer hot power outputs 4 Phase Module state indicators If its ON the cotresponding phase unit is working 5 RCD protector for dimmer hot power outputs exclude the AUX output AUX is protected with separated RCBO Opto and power isolated DMX output 1 Opto and power isolated DMX output 2 DMX input isolated DMX control LED If it s flashing the DMX OO N A pocket is correct when OFF the DMX pocket is incorrect of not present 10 ESCAPE button use to exit from the menu of discard the modification of the selected parameter 11 UP DOWN buttons use to scroll up down on the menu list or increase the value level of the selected parameter 12 ENTER button use to enter to the menu select item and confirm the modification of the selected parameter 13 LCD display PEGASUS CUTE Digital Dimmer Mains distro Outlet of the backside connectors of CUTE H dimmer DIMMER Par A e eee DIMMER Output 7 12 crate ie ea orara Output 1 6 HOTPOWER HOT POWER aa Output 7 12 SE ale carro SUR
11. o 4 2 5 Dimmer PreHeat To give preheat level for output enter into this menu point With the UP DOWN keys select the output and after press SET Now you can set the preheat level by the UP DOWN keys A star indicated next to the level that the data has been changed Press SET and the level will be stored into the memory and you can select another output or press ESC to exit from this menu without saving you modification If you press ESC after pressing the SET you don t want to adjust more channels the dimmer stores the data and exit from the menu The factory default is 0 for each output 4 2 6 Dimmer MaxLevels To set limitation for the output level enter into this menu point Here actually the adjusted level limits the DMX input value to the selected level DON T use this feature to handle 115V bulbs Choose 120V control curve in the next menu point for those channels With the UP DOWN keys select the output and after press SET Now you can set the maximum level by the UP DOWN keys A star indicated next to the level that the data has been changed Press SET and the level will be stored into the memory and you can select another output or press ESC to exit from this menu without saving you modification If you press ESC after pressing the SET you don t want to adjust more channels the dimmer stores the data and exit from the menu The factory default is 100 for each output 4 2 7 Dimmer Curves To sel
12. p C 1 3 5 7 9 11 and output phases for channel 7 8 9 10 11 12 respectively on the Socket B amp D Output neutrals for channel 1 2 3 4 5 6 respectively at Socket A amp C 2 4 6 8 10 12 and output neutrals for channel 7 8 9 10 11 12 respectively on the Socket B amp D no eae ome tee eee PROTECTIVE EARTH PE the side connectors Recommended 16 pole male plug optionally orderable form PLS Male insert HDC HE 16 MT Tension clamp Weidmuller order no 1745840000 ot HDC HE 24 MS crew connection Weidmuller order no 1207500000 House HDC 16B TOBU 1M25G M25 cable gland Weidmuller order no 1788210000 Outlet of the backside connectors of CUTE SX dimmer CAUTION DIMMER DIMMER Re Output 7 12 Output 1 4 HOT POWER HOT POWER Output 7 12 Output 1 6 4 3 Figure 4 Back part connectors 1 DIMMER Outputs for the channels 1 to 6 Ihis connectot refetred in the future as Socket A These outputs are coming from the dimmer circuits 2 DIMMER Outputs for the channels 7 to 12 This connector referred in the future as Socket B These outputs are coming from the dimmer circuits 3 HOT POWER Outputs for the channels 1 to 6 This connector referred in the future as Socket C These outputs are coming directly after the corresponding MCB PEGASUS CUTE Digital Dimmer Mains distro 4 HOT POWER Outputs for the channels 7 to 12 This connector referred in the future as Socket D These outputs are coming directly after the corr
13. solated Not recommended to connect the Pin 1 to the Protect Earth PE The DMX Output 1 and 2 are isolated from the DMX input and refreshed 4 2 Menu specification After pressing the SET button on the dimmer you can reach the following menu points use UP DOWN keys to scroll on the menu list which ones have affect ONLY for the dimmer outputs no affect for direct Hotpower outputs 1 Start Address 2 Test Outputs 3 Run Chaser 4 DMX Patch 5 Dimmer Curves 6 Dimmer Preheats 7 Dimmer MaxLevel 8 Memories 9 If DMX Fails 10 Factory Defaults 11 Dimmer Settings PLS Kft www pls hu To enter to the selected menu press the SET button again otherwise press the ESC to go back the standby display 4 2 1 Start address set In this menu point you can set the global start address of the dimmer from the set address the dimmer receives twelve DMX data and control the outputs from 1 to 12 Use the UP DOWN keys to change the address from 001 to 512 To save the setting press SET otherwise press ESC to go back into the menu list If the dimmer is in softpatch mode you have to disable it before you select global DMX address For it the dimmer ask back when you go into this menu point To disable the softpatch press SET after this question displayed The factory default is 001 4 2 2 Test the outputs of the dimmer After entering this menu you have to select the testing way blinking the output blinks on off in
14. t arrive 2 Fade Out with the selected wait and fade out time the dimmer fade back to zero level after DMxX data fails you can set it in the Dimmer Settings menu section 3 Play memory The dimmer plays the selected memory location if the DMX fails You can set after pressing the SET button by the UP DOWN keys Press SET to store the selected memory number and ESC to exit to the main menu After change of these setting a valid DMX pocket MUST to receive or you have to restart the dimmer disconnect reconnect to have effect for the next DMX fail 4 2 10 Factory defaults To store back the factory settings you can choose from three alternatives by the UP DOWN keys 1 Clear Settings DMX addressing softpatch PreHeat and Maximum levels Control curves 2 Clear Mem Clear only the stored memories not modify the other settings 3 Clear ALL Clear the setting the memories and set back the defaults for the dimmer settings as well Press the SET at the chosen function or press ESC to exit from this menu point 12 4 2 11 Dimmer Settings PLS Kft www pls hu By pressing the SET button three times within two seconds you enter into the dimmer setting menu point where you can adjust the following preferences For each DMX input data 0 255 you can set output level from 0 100 to give Here you can select the Wait Time and the Fade Out time for the If DMX Fails menu Here you can select the display backli
Download Pdf Manuals
Related Search