Lassco Spinnit EBM-2.1 Paper Drill
Contents
1. Traversing the EZ Glide Table Step 8 To move the Table to the next desired hole on the pattern bar press in on either of the Release Handles EZ 1010 located on both ends of the table Press ing in the Release Handle releases the Table Pin allowing the table to traverse Release the Handle and slide the Table until it locks into place in the next desired position Repeat Steps 7 and 8 as desired until complete Table Release Handle Release Handle q Page 09 Operating Instructions Clearing the Chips Step 8 E It is important to clear the chips from the drill bit when you are finished drilling so that the chips won t clog the drill bit Make sure to turn the power off on the machine Place the Chip Clearer CC 2 below the hollow drill bit using one of the three prongs that best fits the drill bit size you are drilling with Making sure it is properly aligned with the drill bit pull down on the handle with very slight pressure allowing the Chip Clearer to push the remaining chips up through the ar drill bit and into the Chip Chute l E Note The CC 2 Chip Clearer was designed for use on drill bits SSS 3 16 in diameter and higher Chip Clearer Note Make sure that if you remove the drill bit to clear the chips you should never force the chips down through the tip of the drill bit Chips should always b2. Operating Instructions Drill bit Removal and Installation Step 1 Step 2 Note Step 3 Step 4 E Remove the hole guard which is attached to the chuck This is done by grasping the bent end and sliding the guard off E Using the Chuck Release Key EBM 32 insert the tapered end facing down into the chuck hole With a clockwise motion turn the Chuck Release Key 45 degrees The drill bit will slide out of the chuck It is recommended that you hold onto the drill bit so that it does not drop out of the chuck damaging the tip Please note that drill bits may be hot after drilling Please wait to change drill bits until they have cooled down E To install a drill bit grasp the drill bit and being careful to keep it straight press it up into the chuck E Seat the drill bit by using a stack of scrap paper or a phone book Set the scrap on the table as shown and pull lightly down on the handle to raise the table toward the drill bit Put ab light pressure on the hollow drill bit seating it firmly in place IEN Remove the scrap paper and turn the machine on to check the i concentricity of the bit If the bit is not concentric remove it and repeat steps 3 and 4 until it is concentric When the drill bit is correctly installed replace the hole guard back onto the chuck to protect debris from clogging the chuck Page 08 Operating Instructions Leveling The Drill Bits Step 6 E To level the drill bits
3. around the entire edge of the chip chute making sure it is snug Note Be sure to empty the chip bag regularly as needed Failure to empty the chip bag can result in clogging of the chip chute Pattern Bars Step 7 E Your EBM 2 1 comes with five pattern bars included Four common patterns and one blank pattern as shown C o o oo e ER 3 holes 2 3 4 apart center to center C o o o US 3 holes 3 1 2 apart center to center O b o x 2 holes 2 3 4 apart center to center TT l o o U 3 holes 4 1 4 apart center to center standard three ring binder E Insert a Pattern Bar by loosening the Pattern Bar Stop EZ 1022 and inserting the desired pattern into the slot on the Pattern Bar Guide as shown in the diagram Insert the angled end into the slot as far as it will go so that the slot at the end of the Pattern Bar lines up with the Pattern Bar Stop When you have the pattern correctly inserted tighten down the Pattern Bar Stop through the slot on the Pattern Bar locking it in place Electrical Start Up Step 8 E Making sure nothing is interfering with the drill bit plug the cord set into a grounded 115V outlet To turn the machine on press the Rocker Switch on the upper left hand side of the shroud 0 Power Cord Rocker Switch E Your Spinnit Paper Drill is now ready for use With proper operation and maintenance it will give you trouble free operation for years Page 07
4. Lassco Spinnit EBM 2 1 Paper Drill User s Manual N Provided By M VuBin ding When Image Matters Lassco Wizer Spinnit EBM 2 1 two Inch Bench Model Serial Number Date of Purchase Dealer Address Before operating this equipment please read these instructions completely and keep these operating Telephone Number instructions for future reference Lassco Wizer 485 Hague Street Rochester NY 14606 U S A Tel 585 436 1934 Fax 585 464 8665 www lasscowizer com info lasscowizer com Table Of Contents Introduction MOON CUO eE EE Page 02 E Shipping Damage INSPeCtiON ccccceeeceeeeeeeeeeeseees Page 02 Safety Information E Salety WINS UC TONS ssis err nna rE E SNES i Page 03 VV ING SS ogee ces cezencevcusere nce ntece niran aA Enn Rea Page 03 E Loose Materials INVOMIONY eccrine ieiccteotaunud ivsanuneedeveaseadnetsdinie Page 04 E 30e Atos 010 en rhe ae eee RE Page 05 E Backgauge ASSN ised ates ect aseseareteed entero eed eneeceorocec Page 06 E Paper Side SIO DS ai ee adenine Page 06 EEND 1219 Rane Nennee nr recente eine ene ete eens ee ee eee rey Page 07 ae S gt coe ee ec ae ee ene meron nee nee Page 07 E Electrical Start UD aemae seen nne ent ae tet en ene mteee ae eta eRe Page 07 E Drill Bit Removal and Installation ccecceeeeeeeeeees Page 08 E Leveling The Drill NS ocsea senate ice teagnaeesadastesrcrsteadedeunce azo Page 09 BT E A aed
5. ace with a screwdriver adjust cam spacers under the V Rollers located on the Fork Plate See Setting Up Your Machine Table pivots front and back Table guides are out of adjust ment Loosen the two screws holding the table guides located on the sides ofthe upright and readjust Page 12 Parts Diagrams Front Back and Side View See Parts List on Page 15 Page 13 Parts Diagrams Interior Front and Back See Parts List on Page 15 Page 14 Parts Diagrams 1 EZ 108A Handle Assembly 2 FM5 5006 Rocker Switch On Off 3 EZ 117A Shroud Assembly 4 FM5 5003 Chuck 5 FM5 5011 Chuck Release Guard 6 Hollow Drill Bit 7 EBM2 0111A Pressure Foot Assembly 38 14 Table Scale 9 EZ 1010L Table Release Handle Left EZ 1010R Table Release Handle Right 11 EBM 44A Channel Guard 12 FM4 4007 Paper Side Stop Knob Table Height Adjustment Knob 13 EZ 1034 Table Guide EZ 107A Pattern Bar Housing Assembl
6. chine from the carton and inspect for any shipping damage If any damage is present report the damage to the carrier immediately Failure to do so may void any warranties Page 02 Safety Information Safety Instructions E All operators must read and understand the Users Manual and all other safety instruc tions before using this equipment If after reading the manual you are still uncertain about use please contact a Service Technician for assistance If you need contact information for a Service Technician nearest you please call 585 436 1934 Failure to fully understand the safety instructions can result in personal injury E This machine is designed for one person operation Never operate the machine with more than one person E Safety of this equipment is the responsibility of the users E Keep hands hair and loose clothing away from the drills E Please read and follow all warning labels on your machine E Always turn the machine off and wait for the drills to stop spinning before installing or removing drill bits Keep hands away from drills when operating PLEASE NOTE THAT THE DRILL BITS MAY BE HOT AFTER USE PROCEDE WITH CAUTION WHEN CHANGING THE DRILL BITS E ONLY A SERVICING TECHNICIAN IS TO SERVICE THIS MACHINE Warning Labels E The following labels appear on your EBM 2 1 paper drill Make sure all operators understand and follow the safety instructions Please read and make sure that all operators understa
7. debe euntaessadevieaen Page 09 E Traversing the EZ Glide Table ccccceccseccseeeeeeeeees Page 09 E Cleaning i gion 7 a 0 eee ener ne ina r Page 10 E DS ON DAN ea Page 10 Trouble Shooting Guide E Problem Cause and Correction cccecececeeeecececeeeeess Page 12 Parts Diagrams E Front Side and Back VICW cccecececececeeeeeeeeceeeseeneess Page 13 E nterior Front and IS ACK ces eee cecetetssee ance seaenesmenanosteueenceeee Page 14 i ee na e en er ee eee ee Page 15 Page 01 Introduction Introduction E Thank you for your purchase of the Spinni EBM 2 1 Paper Drill Lassco Wizer has been designing and manufacturing proven performance equipment for the graphic arts office screen printing sign awards and engraving industries for over 60 years E We ask that you take a moment to fill in the serial number and other information on the front cover of this manual Please keep this manual as a reference for future use E For parts and service please contact the Lassco Wizer Dealer from whom you purchased the machine If you require assistance in locating a Lassco Wizer Dealer nearest you please contact our customer service department at 585 436 1934 Please have the model of your machine and the serial number when you call E f you wish to write to us please contact us at Lassco Wizer 485 Hague Street Rochester NY 14606 Shipping Damage Inspection E Remove the ma
8. e cleared in the same direc tion as when drilling Tips On Drilling E Use a sharp bit at all times Using a drill bit sharpener Lassco Wlzer MS 1 recom mended sharpen your drill bits regularly Apply light pressure when sharpening Too much pressure may cause flaring of the tip Once a drill bit has a flared tip it becomes defective E Sharpening Stone Use to debur the outside cutting edge of the drill bits for better perfor mance E Lubricate drill bits occasionally use Drill Ease or Spin Eze While the drill is running simply touch the Drill Ease stick to the drill bit or brush on the Spin Eze Drill through scrap to remove any excess This will allow for a smoother cut E Drill Strips When drilling a drill bit must stop slightly above the drill strip Replace worn out drill strips regularly to ensure proper drilling Page 10 Maintenance E Remove back panel and lubricate the lift pin with a good grade of light machine oil j Lubricate H Note Refer to your Trouble Shooting Guide for problem solving CAUTION KEEP FINGERS FROM BETWEEN LIFT COMPONENTS OBSERVE ALL SAFETY PRECAUTIONS DURING THE PREVENTATIVE MAINTENANCE OF THIS MACHINE Page 11 Trouble Shooting Guide Problem Cause Correction Drill bit not concentric Foreign
9. g Up Your Machine Backgauge Assembly Step 3 E Assemble the Backgauge by placing the Black Fiber Washer EBM 76 over the Threaded Stud Place the Clamp Bracket EZ 1028 on the Threaded Stud with the knob end toward the center of the assembly Tighten the Elastic Stop Nut on the Threaded Stud with a wrench until it is snug allowing the Clamp Bracket to move with slight resistance Threaded Stud Black Fiber Washer Clamp Bracket amp 1 4 Knob 5 16 18 Elastic Stop Nut Step 4 E Attach the Backguage to the Table by hooking the left end over the Side Iron FM4 4003 on the side as shown in the accompanying picture Align both ends of the Backgauge using the Table Scales 3S 14 so that it is squared correctly When it is positioned as desired tighten down the Clamp Bracket Knob as shown Note Do not position the Backgauge too close to the hollow drill bit so that it touches This can cause serious damage to the hollow drill bit causing it to break or shatter The Backgauge must be at least 1 8 from the circumference of the hollow drill bit Step 5 E Attach the Paper Side Stops FM4 4006 using two Side Stop Screws FM4 4007 each Position the Paper Side Stop as desired and tighten down with light pressure Paper Side Stops Page 06 Setting Up Your Machine Chip Bag Step 6 E Attach the chip bag as shown by stretching the open end over the top hook of the chip chute Continue fitting it
10. material in chuck or in drill plug Inspect and clean Drill bit is bent Replace drill bit Drill bit not seated in chuck properly Reinsert drill bit correctly Chuck is not tight to spindle Tighten set screw Drill bit not drilling Drill bit plugged Remove and clear chips Check for other foreign matter Drill bit dull Sharpen drill bit Note In extreme conditions the drill chuck and or chip chute may be plugged Remove the drill bit loosen the chip chute pull down and clean See Operating Instructions Table lift system lifts unevenly or is noisy Ball bushings in lift system dry or worn Lubricate or replace Lift pin damaged Replace lift pin Machine vibrates wobbles resonates etc Drive motor loose Tighten Machine is sitting on eneven surface Reposition drill to obtain concentricity Drill bits are out of concentricity Reinstall drill bits to obtain concentricity Drill bit drills into drill strip drill bits not drilling through bottom sheet of paper Drill bit was not adjusted to card stock card stock not used Adjust per Operating Instructions Operator not allowing full travel of table Drill per Operating Instructions through full drilling cycle Table is too tight or too loose when sliding V Rollers under table out of adjustment With an open end wrench and holding screw head in pl
11. n Step 1 Note Table Slide Stop Release Handles Note Step 2 E Grasping the Table and depressing the Release Handles to unlock the Table Pin slide the V Bars located on the underside of the Table into the V Rollers on the Base of the machine as shown Please note that one of the Table Stops EZ 1014 comes installed Make sure when installing the Table onto the Base you are sliding it from right to left while facing the machine to avoid obstruction from the pre installed Table Stop V Bars Table Pin EN C o o Fork Plate V Rollers Underside of Table Cam Spacers Please note that although they are factory set you may have to adjust the cams on the V Rollers if the Table is too tight or too loose after installation If so remove the Table With an open end wrench and holding the screw head in place with a screwdriver adjust the cam spacers under the V Rollers If the Table is too tight adjust the V Rollers out towards the edge of the Fork Plate EZ 1000 If the Table is too loose adjust the V Rollers in toward the center of the Fork Plate E Attach the second Table Stop EZ 1014 to the underside of the table using two 1 4 lock washers and two 10 32 Elastic Stop Nuts as shown Tighten with a wrench until secure 1 4 Lock W shers AO 10 32 Elastic Stop Nuts O Page 05 Settin
12. nd the operators manual and all other safety instructions before using this equipment Page 03 Setting Up Your Machine Loose Materials Inventory E Remove and inspect the following items EZ 114A Table Assembly 1 EBM2 1034 Drill Strip 1 This item comes installed Q O 0 S on the table as shown fe o S o A N J A EZ 115A Backgauge 1 EZ 1016 Pattern Bars set of 5 bb 50 35 5 16 18 EBM 76 Elastic Stop Nut 1 Black F ber Washer 1 EZ 1028 Clamp Bracket 1 amp FM7 7005 1 4 Knob 1 N FM4 4006 Paper Side Stops 2 FM4 4007 Side Stop Screws 4 EBM2 1048 Chip Bag 1 EZ 1014 Table Stop 2 of JO One of these items comes installed 10 32 Elastic Stop Nuts 2 OO 1 4 Lock Washers 2 OO Hollow Drill Blt 1 a This item comes installed Spin Eze Drill Bit Lubricant 1 KDE CC 2 Chip Clearer 1 EBM 32 Chuck Release Key 1 C J a CD C_D E HEX 18 Hex Wrench 1 8 1 HEX 332 Hex Wrench 3 32 1 Page 04 items are not to scale Setting Up Your Machine Table Assembly Installatio
13. to the Table first loosen the Leveling Knob on the right hand side of the machine as shown Pull down on the Handle to raise the Table until the hollow drill bit is just touching the Drill Strip EBM2 1034 Hold the Handle in place and tighten down the Leveling Knob until it hits the Handle Bracket This will stop the Handle from being pulled down too far It is important to always reset the Level with each use This will make sure you don t drill into the Drill Strip dulling the hollow drill bit Note We recommend using a piece of card stock on the Table when leveling the drill bits to avoid drilling into the drill strip This will lengthen the life of your drill bits and keep them sharper Step 7 E When you are ready to drill set the product to be drilled on the table and make sure it is secure using the Paper Side Stops Turn the machine on and holding the product firmly in place with one hand pull down on the Handle raising the Table up to meet the drill bit Using one consistent smooth stroke put pressure on the Handle so that the Table rises fully allowing the drill bit to drill through the product It is important you maintain a consistent speed through the entire stack It is also important you do not go too slow or too fast If you drill too slow you can burn the paper leaving undesired marks If you drill too fast the drill bits will act more like a punch and they will break or plug
14. y 15 EZ 1022 Pattern Bar Stop 16 EZ 1004 V Rail 17 EBM2 110A Chip Chute Assembly EBM2 1047 Chip Bag Bracket FM5 5008 Power Cord 20 FM4 4003 Side Iron 21 EBM2 1034 Drill Strip 22 EZ 1033 Table 23 EZ 1025 Base Wire Harness 25 FM5 5002 1 4 HP Motor 26 EBM2 1000 Lift Pin 27 EZ 1001 V Roller EBM2 111A Housing Assembly 29 EBM2 1019 Pivot Hub EBM2 103A Pivot Arm Set Assembly 31 EZ 1026 Lift Bars 32 EZ 1023 Lift Pin Housing 33 EZ 1024 Fork 34 EZ 1000 Fork Plate 35 EZ 1003C Cam Spacer Page 15
Download Pdf Manuals
Related Search