Zycont User`s Guide - Duplicator Technical Support
Contents
1. Startup Command Copy Comp Q d Press the lt GO gt button to confirm your selection You then be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu You have now successfully set the Startup Command to Copy Comp 35 Chapter 4 Audio CD Editing This process shows you how to perform the Audio Track Selection feature It is used to combine audio tracks from various CDs into a single customize audio CD In order for the controller to do all those things you will need a temporary storage location to hold your songs before the controller can make it an audio CD The following are the choices you will have Hard Drive if a hard drive is installed If you choose the hard drive as the temporary storage location you will load all of your favorite songs into the hard drive and then copy them onto a blank 80 minute CD R media Blank CD R Media If you choose a Blank CD R as the temporary storage location you will copy all of your favorite songs onto the blank CD R one track at a time After you have finished you will finalize the CD R disc To edit audio CDs using the hard drive go to Audio CD Editing using the Hard Drive on page 37 To edit audio CDs using the Blank CD R Media go to2. This menu option selects the command that will be displayed at startup Autoloader This function allows the controller to support an external robot for automatic disc placement For additional support contact our Technical Support department using the information on the back of this manual 58 Edit The Edit menu will guide you to perform the Audio Tracking Selection feature This feature will help you combine audio tracks from various CDs into a single customized audio CD For additional information refer to Audio CD Editing on_page 45 Disc Info This feature will show the CD DVD media information for all CD DVD discs inside the duplication system Show Drive This menu option is used to show the types of drives installed in the duplication system Enter the Show Drive option using the lt GO gt button and use the lt MODE gt or lt BACK gt buttons to scan through the drives Press the lt GO gt button to return to the next higher menu Burn in This feature will help the system to check on the performance while simulating the mode you have choose Update This function will update the software in your controller To update you will need to insert manufacturer Certified Update CD into the Reader and select this function by pressing the lt GO gt button We strongly suggest you do not upgrade your controllers firmware unless your system is becoming unstable Clear This feature erases the current partition on
3. blank media it has detected your CD in the unit of audio playback time u 7 indicates the number of blank media it has detected b Once the number of blank discs you inserted matches the number of discs detected on the screen press the lt GO gt button to confirm and you should see a Progress screen similar to the following Copy 0363 0551M CD Copy Ae 38 10X The numbers in the top line indicate that 0551 MBytes M out of the total 0363M have been copied so far The CD on the right hand side indicates that the source media is a CD ROM The numbers 4 38 in the center of the bottom line indicate the time since the copy operation started The 32X indicates the copy speed 16 Note If the number of blank discs you inserted does not match the number of discs detected on the screen wait 10 15 seconds for the controller to recognize all of your blank discs Note By default the duplication process will begin automatically if all of the writer trays are filled with blank media c Once the duplication run is completed you should see the following screen OK 3 NG 0 TOK 9 Copy OCEM 10X OK 3 indicates that there were three successful OK copies on this run NG 0 indicates the number of copies that were No Good TOK 9 indicates that you have nine successful copies total d Your good copies will be ejected Next insert more blank discs to make more copies Or you can press the lt MODE gt button to go ba
4. buttons to choose track number 10 and then press the lt GO gt button to confirm You should see the following screen Total SERA im STS Track MOE 2m 12s s To tell the system that you are finished with Disc 2 use the lt MODE gt or lt BACK gt buttons to go past the last track on the disc You will see a screen similar to this Total SENAK 14m 37s Are you done t Press the lt GO gt button to proceed You should then see the following screen Finalize No Q u Since you have selected all the tracks press the lt MODE gt button to select Yes under Finalize and you should then see a Loading screen similar to this Edit 060 125 CD Edit 4 03 10X 52 v When this is complete the system will eject your master disc in the Reader tray and finalize the disc in the Writer tray When finalization is complete the disc in the Writer tray will be ejected and you will be returned to the Edit menu Edit lt mode Step 4 Start the Copy Process a Insert blank discs into each of the writers trays that you want to use and allow 5 10 seconds for the system to detect the blank discs After the blank discs have been recognized you should see a screen similar to this Copy 551M62 42 lt mode Jstart gt 551M indicates the capacity of your CD in the unit of the MB u 62 42 indicates the capacity of your CD in the unit of audio playback time 7 indicates the number of blank media it has detected Note Make s
5. If it still does not work turn off the machine and then restart the machine after a minute d Copy completed but the copies are not readable or executable Use the Compare feature to check the copied discs Based upon our experience the quality of your media plays a big role on this part Try to use quality media to prevent such problems Use another DVD CD player ROM to test the copied media Sometimes your DVD CD Player ROM may not be compatible with recordable DVDICD discs e The failure rate is high Lower the write speed and try again Refer to Selecting the Duplication Speed on page 28 for additional information Quality of the blank disc may be poor Quality of your Master disc may be poor f Do I need to upgrade my controller s firmware Unless your system is becoming unstable we strongly suggest you do not upgrade your controller s firmware Contact our distributors if your system is becoming unstable g Cannot boot up or fail to upgrade firmware Contact Tech Support 60 h Can I load data directly from my computer to my systems attached hard drive No not at all Your system s hard drive has a unique file system that no computer will recognize Therefore you cannot perform any read or write operations to the hard drive from your computer i Why some writers won t copy u Reset back to default refer to Troubleshooting item j u Maybe the writers are bad Contact the d
6. disc then you will see a screen similar to this Total Tua 6m 29s Are you done j Press the lt GO gt button to proceed You should then see the following screen Finalize No Q k Because you are not through adding tracks use the lt MODE gt or lt BACK gt buttons to choose No for finalization Press the lt GO Button to proceed You should then see a loading process screen similar to this Edit OTS AZENMI CD Edit 2108 10X 015 125M indicates the amount of data read from the disc CPD indicates that the mast disc is a CD ROM 2 03 indicates the time that the current operation has taken 10X indicates the drive read speed m Because you said No to finalize when the loading process is finished you should see the following screen Edit Insert next master 51 n Insert CD2 and you should see the following screen Total PERAR 6m 29s Track l 3m 57s o Use the lt MODE gt or lt BACK gt buttons to choose track number 9 and then press the lt GO gt button to confirm You should see the following screen Total 2 Trk 6m 29s Track 9 2m 53s p Press lt GO gt button to confirm You should then see the following screen Total Smits 9m 22s Track 9 2m 53s q Use the lt MODE gt or lt BACK gt buttons to choose track number 3 and then press the lt GO gt button to confirm You should see the following screen Total Amiga 12m 25s Track 3 3m 03s r Use the lt MODE gt or lt BACK gt
7. lt BACK gt buttons to change the X indicated in the previous screen to an A as in the following screen HDD Partition Group El A Q d Press the lt GO gt button once until the following screen is shown HDD Partition of A SJ Ox Q e Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to a B as in the following screen HDD Partit1OnNNORAE MB f Press the lt GO gt button and you will be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be sent back to the Copy menu Step 3 Load Your Favorite Tracks onto the Hard Drive a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Use the lt MODE gt or lt BACK gt buttons to select the Clear menu as shown in the following screen Clear lt mode 38 Note You must perform the Clear function before you load your favorite tracks onto the hard drive c Press the lt GO gt once to execute the Clear function Once the partition has been cleared you will see this message Master Cleared d You will then be directed back to the Copy menu Copy lt mode e Press and hold the lt MODE gt button for three seconds and
8. release it after a beep has sounded You should see the following screen Set up lt mode Go gt f Use the lt MODE gt or lt BACK gt buttons to select the Edit menu as shown in the following screen Edit lt mode g Insert an audio CD that contains your favorite track s in the Master reading tray and make sure no other discs remain in the rest of the trays If your Master reading source is not the Reader make sure the Reader tray does not have any discs inside the controller will analyze your CD and after 5 10 seconds you should see a screen similar to the following Total Omak 0m 00s Tracks 2m 52s Total 0 Trk represents the number of tracks selected 0 at this point 0m 00s indicates the sum of the selected track times in minutes and seconds Track 1 indicates the track that is currently selected 2m 52s indicates the length of the selected track in minutes and seconds 39 h When you see previous screen you can use the lt MODE gt or lt BACK gt buttons to choose the track number that you would like to add and press the lt GO gt button to confirm If you selected Track from the previous menu you should see the following screen Total dias 2m 52s Track mis 2m 52s i Use the lt MODE gt or lt BACK gt buttons to choose the next track number you would like to end and press the lt GO gt button to confirm You should then see a screen similar to this Total 2a 6m 29s Trackor 3m
9. using the Hard Drive Audio CD Editing using Blank CD Rs Editing Audio Tracks to Blank CD R Media Tutorial Editing Audio Tracks to the Hard Drive Tutorial Menu Overview Main Menu Overview Advanced Menu Overview Trouble Shooting OOO R 14 15 17 17 23 24 26 30 31 35 36 36 42 45 48 55 55 56 60 Chapter 1 Installation Additional Components Needed Before you install the Zycont Duplication Controller into a duplication system make sure you have following drives ready Figure 1 1 ATAPI IDE Disc ROM Reader or ATA IDE Hard Drive Optional Cc Figure 1 2 ATAPI IDE Disc R RW RE Writer We recommend the following brands Pioneer NEC Sony Plextor Asus etc For stable duplication ensure all writers have identical model names and firmware revisions FS o Figure 1 3 Suitable Tower Case with Power Supply Make sure that your tower case has enough bays for all the drives In addition make sure the power supply is of sufficient wattage and reliable Low grade power supplies may cause the system to become unstable and cause severe damage to both the controller and all other devices Assembling Installation Preparing the Drives Jumper Setting Except as noted the jumper settings for every drive should be set to Master mode MA man p esse Jo oo 0 Figure 1 4 Jumper Setting to the MA Master T
10. your current Master Reading Source is the top tray in order to avoid unnecessary error Messages a To check the Master reading source press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should then see following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD to CD eee Q Where XXX is either Yes or No c Press the lt MODE gt or lt BACK gt buttons repeatedly to set this option to Yes as shown in the following screen and press the lt GO gt button to confirm CD to CD Yes IO 15 d You will then be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see following screen Setup lt mode go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu Step 2 Start the Copy Process a Insert your Master disc and your blank discs into the corresponding tray s Allow 5 to 10 seconds for the controller to detect your Master disc and the blank discs You should then see the following screen For DVD Duplication For CD Duplication Copy 4352MDVD Copy 551M62 42 lt mode Istar ta lt mode Stan e 4352M indicates the capacity 678M indicates the capacity of of the Master disc in the MB your CD in the unit of the MB 7 indicates the number of 77 13 indicates the capacity of
11. 37s j You can continue to add tracks from this disc until either you are finished or the total time equals 80 minutes by repeating Steps d i To tell the controller that you are finished with this disc use the lt MODE gt or lt BACK gt buttons to go past the last track on the disc You will see a screen similar to this Total T2 oms Are you done k Press the lt GO gt button to proceed You should then see the following screen Finalize No Q 1 Use the lt MODE gt or lt BACK gt buttons to choose Yes or No for finalization Finalization will make your new mixed CD playable in an audio CD player but you will not be able to add any more tracks to it If you choose Yes you cannot add any more audio tracks to your selection If you choose No you can add more audio tracks from other audio CDs to your selection but you will not be able to listen to the CD until it is finalized m Press the lt GO gt Button to proceed You should then see a loading process screen similar to this Edit 02 125M CD Edie 2 06 10X u 02 125M indicates the amount of data read from the disc CD indicates that the mast disc is a CD ROM 2 03 indicates the time that the current operation has taken 10X indicates the drive reading speed 40 n If you said No to finalize when the loading process is finished you should see the following screen Edit Insert next master To load more tracks from other audio CDs repeat steps
12. 3m 58s Track TOR 2m 02s n Since you are done with CD2 scroll down to finalize You should then see the following screen Finalize No Q o Since you have selected all the tracks press the lt MODE gt button to select Yes under Finalize and you should then see a Loading screen similar to this Edit 060 125 CD Edit 4 03 10X p The system will eject your master disc in the Reader tray and finalize the disc in the Writer tray When finalization is complete the disc in the Writer tray will be ejected and you will be returned to the Edit menu Edit lt mode Editing Audio Tracks to the Hard Drive Tutorial This example shows you how to create a new Audio CD from two different discs when using the hard drive CDI Song 1 and song 5 CD2 Song 9 song 3 and song 10 You are going to load all those tracks onto the hard drive partition B of group A Then you are going to copy them onto a blank CD R disc Step 1 Make sure the Master reading source is set to the hard drive a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD tome XXX Q 48 c Use the lt MODE gt or lt BACK gt buttons to set this option to No as in the following screen and press the lt GO gt button to confirm CD tomer No Q d You
13. DE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt 1 There are many factors that contribute to the capacity difference between the advertised capacity and the actual capacity Hard drive manufacturers use a conversion rate of 1GB 1 Billion Bytes or 100043 Bytes However most Operating Systems including our controller use the standard conversion rate of 1GB 1 074 Billion Bytes or 102413 Bytes Therefore for an advertised 80GB hard drive 80 Billion Bytes the Duplication System capacity is actually 74 5 Billion Bytes 74 5GB In addition we round off all fractions of a GB to the lower whole number That means for a hard drive that has a 74 5GB system capacity we only recognize and use 74GB 26 a Press the lt GO gt button repeatedly until you see the following screen CD to CD XXX Q b Use the lt MODE gt or lt BACK gt buttons to set this option to No as indicated in the following screen and then press the lt GO gt button to confirm CD tGJGB FINE Q c Press the lt GO gt button repeatedly until you see following screen Setup lt mode Go gt d Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu Step 2 Specify the active slot or partition If you have already loaded your Master disc onto the hard drive then you can s
14. Editing Audio Tracks to Blank CD R Media Tutorial on page 46 Audio CD Editing using the Hard Drive When you turn on your duplication system you should see the following screen when your controller is ready Copy lt mode Step 1 Select the Master Reading Source To load your favorite tracks onto the hard drive make sure the Master reading source is set to the hard drive in order to avoid unnecessary error messages To check the Master reading source do the following a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD to CD oes Q 36 c Use the lt MODE gt or lt BACK gt buttons to set this option to No as shown in the following screen and press the lt GO gt button to confirm CD teem No Q d You will then be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu Step 2 Specify the Active Slot or Partition To load your audio tracks onto the hard drive you need to specify the slot partition where you want the audio stored Each slot partition has a unique index ID This index ID consist
15. GO gt button to confirm You should then see a screen similar to this Total 2a 6m 00S Track isi 3m 08s 46 f Tell the controller that you are finished with this disc by using the lt MODE gt and lt BACK gt buttons to go past the last track on the disc You will see a screen similar to this Total TE 6m 00S Are you done g Press the lt GO gt button to proceed You should then see the following screen Finalize eal No Q h Since you have more tracks to copy use the lt MODE gt or lt BACK gt buttons to select No under Finalize and you should then see the following Loading screen Edit 01157025M CD Edit 206 10X i When the loading process is finished CD1 will be ejected and you should see the following screen Edit Insert next master j Insert CD2 and you should see the following screen Total 2a 6m 00s Track amii 2m 17s k Use the lt MODE gt or lt BACK gt buttons to choose track number 9 and then press the lt GO gt button to confirm You should then see the following screen Total SERAK 8m 53s Track 9 2m 53s 1 Use the lt MODE gt or lt BACK gt buttons to choose track number 3 and then press the lt GO gt button to confirm You should see the following screen Total Amaia 1im 56s Tracker 3m 03s 47 m Use the lt MODE gt or lt BACK gt buttons to choose track number 10 and then press the lt GO gt button to confirm You should see the following screen Total Sala 1
16. Master disc When you load your Master disc onto the hard drive a unique image is created for that Master disc and everything you do is related to the selected image The capacity of the partition created is the same as the size of your master disc rounded up to the next Gigabyte GB The number of partitions the hard drive can hold is determined by the capacity of the hard drive and the size of the partitions created For example if you have an 80GB hard drive with a system capacity of 74GB You can load 74 CDs or 19 DVDs given a 4GB average capacity Making Copies from the Hard Drive The following steps will show you how to load your Master disc into the hard drive as a disc image and copy the stored disc image on to several blank discs This process is recommended for mass volume productions Turn on your duplication system Once the controller has completed its self tests you should see the following screen Copy lt mode Step 1 Make sure that the Master Reading Source is set to the hard drive The Master reading source should be set to the hard drive in order to avoid unnecessary error messages a To check the Master reading source press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until following screen is shown CD to CD DEER Q c Use the lt MODE gt or lt BACK gt bu
17. Zycont User s Guide www zycont com Email ventasQzycont com Copyright and Trademark Information The product and material in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor who assumes no liability or responsibility for any errors that may appear in this Manual All brand names and trademarks are properties of their respective owners This manual contains materials protected under International Copyright Laws All rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of Zycont The Zycont controller is to be used in a lawful manner Violation of the International Copyright Laws is a criminal charge Zycont is not responsible for the illegal actions of users nor consequential damage in connection with the furnishing performance or use of the equipment described herein Table of Contents Installation Additional Components Needed Assembling Installation Preparing the Drives Installation Operation Display and Controls Tutorial Guide Making Disc to Disc Copies Making Hard Drive to Disc Copies Selecting the Duplication Speed Selecting the Disc Reading Source Loading the Master Disc onto the Hard Drive Specifying the Active Slot or Partition on the Hard Drive Deleting an Existing Image in a Slot or Partition Changing the Setup Settings Audio CD Editing Audio CD Editing
18. ace will make your copying job easier than ever before Words and Terms Reader The first tray from the top of your duplication system Writer All of the trays below the reader Limitations The CD DVD BD controller will not copy a copyright protected CD DVD BD Normally most discs purchased do have some kind of copy protections BD Blu Ray 13 Display and Controls Figure 2 1 shows the LCD front panel and the front panel controls Figure 2 1 LCD Front Panel The LCD Display Panel displays the main functions and all messages Table 2 1 Front Panel Controls Control Name Function Selection for the next function Mode Scrolls up though the menu Selection for the previous function Back Scrolls down the previous menu Go Executes the function you selected 14 Tutorial Guide Making Disc to Disc Copies This process will copy a Master disc onto several blank discs simultaneously Due to it s simultaneous nature a good condition Master disc and lower recording speed is necessary for both higher duplication success rates and good quality duplicates Turn on your duplication system Once the controller has completed its self tests you should see the following screen Copy lt mode Step 1 Make sure the Master reading source is set to Reader If your duplication system does not have a hard drive inside skip to Step 2 on page 17 Note It is very important to make sure that
19. ances you might want to lower the duplication speed Those circumstances are as follows u Poor Blank Media Quality When your media quality is questionable lowering the duplication speed is necessary to make good copies u Poor Master Disc Quality If your Master disc condition is not good lowering the duplication speed will greatly reduce failure rates Duplication Quality Overall the lower the speed the higher the quality of your copies If you have time it is a good choice to lower the speed to produce good quality copies There are five types of recording speed u CD Copy the CD disc to CD R discs directly On The Fly DVD Copy the DVD disc to DVD R discs directly On The Fly HDD to CD Copy the hard drive CD image to CD R Discs HDD to DVD Copy the hard drive DVD image to DVD R Discs HDD to BD Copy the hard drive BD image to BD Discs Note 1 This only applies to CD DVD BD duplication systems Note 2 This only applies to duplication systems equipped with hard drives To achieve 16X or higher DVD duplication speed performance The source must be a hard drive image You must use 16X or higher speed certified recordable media In the following example you will see how to adjust the CD writing speed You should see the following screen when your controller is ready Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the follow
20. available basic menus You can navigate them by pressing the lt MODE gt button Copy This menu will perform duplication from an active Master disc For additional information refer to Making Disc to Disc Copies on page 17 Copy and Compare Copy Comp This menu will guide you to make copies and after the copy process has been finished it will compare the copies to the original to ensure that they have been copied correctly Emulate This menu will guide you to make simulation of copying process During this simulation process all write once recordable discs such as DVD R CD R will be reusable The purpose of performing such simulation is to ensure error free duplication Note Due to the physical limitation of DVD R recordable format you can not perform this procedure if your recordable discs are DVD R If you do so you will encounter failure messages Note If you are using CD DVD reWritable discs as your blank media during the simulation all of the content inside those discs will be erased permanently Emulate and Copy Emu Copy This menu will guide you to perform the simulation of copying process and if everything has passed during the simulation a real copying process will be performed If there s an error encountered during the simulation an error message will be displayed and the copying process will not be initiated Load XX This menu loads the contents of the Master reading source into the currentl
21. ck to the Copy menu Note Failed discs bad copies are not automatically ejected You will need to manually eject them in order to continue Making Hard Drive to Disc Copies for Duplication Systems with a HDD Installed Copying from the hard drive is the best way to make copies There are four benefits to copying from the hard drive Performance Duplicating from the hard drive will boost the CD DVD BD duplication performance for duplication speeds of 16x or greater performance Stability Duplicating from the hard drive will stabilize the duplication process compared to disc to disc copies Durability The hard drive is a much better storage device than the recordable discs The recordable discs are composed of chemical materials that tend to degrade over a period of time while hard drives are made of magnetic disk that will last over a 100 years the recordable discs are also exposed and are very easy to scratch while hard drives are covered with metal and mounted inside the duplication system Convenience With your Master discs stored inside the hard drive you can access each one easily There is no need to carry your Master discs it is all inside the duplication system 17 The optional built in hard drive is divided into a number of partitions or slots Each partition holds one and one ONLY Master disc image regardless of the capacity of your Master disc A Master disc image is a file that contains everything on your
22. e For ease of cable routing the controller should be approximately centered in the case Reader Writer Figure 1 8 Controller installed in an 13 Drive Case For all IDE cables connect the blue colored end of the IDE cable to the controllers as shown in Controller Cabling on page 7 Note IDE cables are provided in various lengths Use them based upon the placement of the writer drive in the case Figure 1 9 Controller Cabling Insert the controller with the IDE cables connected into the corresponding bay in the Tower Case IDECables Figure 1 10 Controller Installed in a Case Connect a loose black colored end of the IDE cable to each of the drives nak rez H e GL we NF ka a wos i mes me pl zo Z Figure 1 11 Controller IDE Cabling Connect the power adaptor from the power supply to each drive as well as the controller Warning Ensure the power input is installed in the correct direction on the controller s power connector to avoid damaging the controller e z re oo eh Figure 1 12 Controller Power Cabling 11 The installation is complete Close the tower and install the case screws KN Pa NHA Figure 1 13 Closing the Case Chapter 2 Operation The ZYCONT controller is a reliable high performance high speed standalone CD DVD Blu Ray duplicator controller It s professional industrial design and simple user interf
23. e the copy operation started The 10X indicates the copy speed If the number of blank discs you inserted does not match the number of discs detected on the screen wait 10 15 seconds for the controller to recognize all of your blank discs c Once the duplication run is completed you should see the following screen OK 3 NG 0 TOK 9 Copy 6 58 MOR u OK3 indicates that there were three successful OK copies on this run NGO indicates the number of copies that were No Good TOK 9 indicates that you have nine successful copies total d Your good copies will be ejected Next insert more blank discs to make more copies Or you can press the lt MODE gt button to go back to the Copy menu Note Failed discs bad copies are not automatically ejected You will need to manually eject them in order to continue Audio CD Editing using Blank CD Rs When you turn on your duplication system you should see the following screen when your controller is ready Copy lt mode When editing audio CDs directly to black CD Rs make sure the Master reading source is set to the Reader drive in order to avoid unnecessary error messages To set the Master reading source do the following a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD to
24. g m o If you said Yes to finalize the controller will bring you back to the Edit menu as shown in the following screen Edit lt mode p Use the lt MODE gt or lt BACK gt buttons to return to the Setup menu Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu Step 4 Begin the Copying Process a Insert blank discs into each of the Writer trays that you want to use and allow 5 10 seconds for the controller to detect the blank discs After the blank discs have been recognized you should see a screen similar to this Copy 551M62 42 lt mode 7start gt 551M indicates the capacity of your CD in the unit of the MB 62 42 indicates the capacity of your CD in the unit of audio playback time 7 indicates the number of blank media it has detected Note Make sure you have taken the Master disc out of the Reading tray before proceeding with the copying process Failure to do so will result unnecessary error messages b Press the lt GO gt button to confirm and you should see the following Progress screen Copy 0363 0551M CD Copy 4 38 10X The numbers in the top line indicate that 0551 MBytes M out of the total 0363M have been copied so far The CD on the right hand side indicates that the source media is a CD ROM 41 u The numbers in the center of the bottom line indicate the time sinc
25. he exception is when you connect both the reader and the hard drive to a single port via the same IDE cable For this configuration set the hard drive to Master1 and set the reader drive to Slave READER HARD DRIVE C gt EZ SL uooocoaoooocooooocoooocooo ooo UlLsooooooaooooaanacoso ooojejj OOOO erran f ooooooooooo0000000000000000 loooo qi ojojo ooooooonoooooooooooonoooooo OOOO X 10 1 Figure 1 5 SL Slave MA Master with Slave Present 1 Some drives such as Western Digital and Hitachi require a jumper setting of Master with a Slave present IDE Cables Prepare all IDE cables One IDE cable is used for every drive If needed the hard drive and the reader can share the same cable using a special three connector IDE cable IDE cables are provided in various lengths to suit different controller placements in a case Blue Controller GOOLOOOOOOOOODOWODONO C Figure 1 6 Regular IDE Cable Blue Reader Controller Hard Drive a DOCDOCOOCDCOOCOCEOCOGOCO OODIO OOOO OCIOOOCOOO 6 DODLUODOOOLOOOOODODOOOO BRR R RRB ARE e rane Figure 1 7 Special Three Connection IDE Cable Installation Note The following examples show how you can assemble the controller into an 11 drive Tower Case Use a similar principle for other cases Mount all drives into a bay in the Tower Cas
26. ing an Existing Image in a Slot or Partition If for some reason you would like to permanently delete your existing image in a slot or partition perform the following steps Note You do not have to delete the existing image in a slot or partition before you load a new image into that slot or partition Loading a new image will overwrite the existing image If you want to delete partition B of group A do the following The following procedures only apply to duplication systems with hard drives installed When you turn on your duplication system you should see the following screen when your controller is ready Copy lt mode 31 Step 1 Make sure the Master reading source is set to the hard drive It is very important to make sure the Master reading source is the hard drive in order to avoid unnecessary error messages To check the Master reading source press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt a Press the lt GO gt button repeatedly until the following screen is shown CD to CD 222 Q b Use the lt MODE gt or lt BACK gt buttons to set this option to No as indicated in the following screen and press the lt GO gt button to confirm CD toges Ne Q c You will be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt m
27. ing screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD Write Speed 28 Q The XX is the speed you can choose 23 c Use the lt MODE gt or lt BACK gt buttons to select your desired speed d Once the desired speed is selected press the lt GO gt button to confirm e Then press the lt GO gt button repeatedly until the following screen is shown Setup lt mode Go gt f Once the speed is set press and hold the lt MODE gt button for three seconds and then release it after a beep has sounded You will be guided back to the Copy menu You have now successfully changed the duplication speed Selecting the Disc Reading Source Applies to Disc to Disc Duplication ONLY When you try to make a copy from disc to disc on the fly you will need to specify whether the Master disc is in the Reader tray or is it in another Writer tray This tutorial will show you how to change the disc reading source to satisfy your needs Note that in order for this feature take effect you need to change the CD to CD setting to Yes inside the Setup menu Basically there are two scenarios that require you to select the Master reading source u Disc to Disc Copies read from the Reader tray Used when you would normally make copies on the fly You need to set the setting to Auto as your Master reading source Disc to Disc Copies read from the Writer tray Used whe
28. is finalized i Press the lt GO gt Button to proceed You should then see a copying process screen similar to this Edit 0157P M CD Edit 2108 10X 015 125M indicates the amount of data read from the disc CD indicates that the mast disc is a CD ROM 2 03 indicates the time that the current operation has taken 10X indicates the drive read speed 44 j If you said No to finalize when the loading process is finished you should see the following screen Edit Insert next master To load more tracks from other audio CDs repeat steps c h k If you said Yes to finalize the controller will eject your master disc in the Reader tray and finalize the disc in the Writer tray When finalization is complete the disc in the Writer tray will be ejected and you will be returned to the Edit menu Edit lt mode Editing Audio Tracks to Blank CD R Media Tutorial This is an example of how to create a new audio CD from two different discs CDI Song 1 and song 5 CD2 Song 9 song 3 and song 10 Step 1 Make sure the Master reading source is set to the Reader a To check the Master reading source press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown CD CONCH see Q c Use the lt MODE gt or lt BACK gt buttons to set
29. istributors j How do I reset my controller s settings back to default Power off the system Press and hold the lt MODE gt button while the system remains off While you are holding the lt MODE gt button turn on the system and remain holding the lt MODE gt button Once you hear a long beep sound release the lt MODE gt button You should see a screen similar to this Clear Setup www zycont com Email ventas zycont com 61
30. ive then you can skip this step and go to Step 4 on page 30 At this point you should see the following screen Copy lt mode a Use the lt MODE gt or lt BACK gt buttons to change to the Load option as shown in the following screen Load lt mode b Insert your Master disc into the top reader tray and make sure there are no discs in the other trays After 5 10 seconds your Master disc will start to load into the hard drive partition B of group A partition AB Load 0302 0650M CD Load 2 33 OX c Once the loading process is complete you should see the following screen Pass Load Al e152 0x Step 4 Return to the Copy menu a Press the lt MODE gt button once and you should see the following screen Load AB551M62 42 lt mode b Use the lt MODE gt or lt BACK gt buttons to select the Copy menu as it appears in the following screen Copy AB551M62 42 lt mode You have now successfully loaded your Master disc into the partition AB of the hard drive If you would like to make copies refer to Making Hard Drive to Disc Copies on page 18 29 Specifying the Active Slot or Partition on the Hard Drive A slot or partition is a unit that holds a single image that represents the Master disc you have loaded onto the hard drive The active slot or partition tells the controller which existing image inside the hard drive you want to use as the Master recording source The hard drive inside the duplication syste
31. k to the Copy menu Step 3 Deleting the Active Partition At this point you should see the following screen Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Use the lt MODE gt or lt BACK gt buttons to select the Clear menu as shown in the following screen clean AB0551M62 42 lt mode Go gt c Press the lt GO gt button once and you should briefly see the following screen Master Cleared d Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu You have now successfully deleted partition B of group A 34 Changing the Setup Settings Most of the internal settings and information are stored inside the Setup menu To explore or modify them is simple Following is an example of modify the Startup Command to Copy Comp Once the controller has finished its self test you should see the following screen Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown Startup Command Copy Q c Use the lt MODE gt or lt BACK gt buttons to select the Startup Command menu as shown in the following screen
32. kip this step and go to Step 4 on page 30 In order to load your Master disc onto the hard drive you need to specify the slot or partition where it should be loaded Each slot or partition possesses a unique index ID This index ID consists of two characters such as AD The first character A represents the partition group and the second character D represents the partition index for that particular group Each group holds 26 partition ranging from A to Z Normally you should have only group A however if your hard drive has more than 26 partitions then you should see more groups such as B C etc to hold more partitions If your hard drive consists of 12 partitions then you should only have one partition group A with 12 partitions inside The indexes IDs for your partitions are as follows AA AB AC AL gt 12 Partitions Total Partitions gt 12 Partitions Or if your hard drive consists of 60 partitions then you will have three partitions groups A B and C with 26 partitions for groups A and B but only 8 partitions for group C The indexes IDs for your partitions are as follows AA AB AC AZ gt 26 Partitions BA BB BC BZ gt 26 Partitions CA CB CC CH gt 8 Partitions Total Partitions gt 60 Partitions 27 If you want to set the partition B of group A as the active slot or partition do the following The following procedures only apply to duplication systems with hard drives insta
33. lected track in minutes and seconds 43 d When you see previous screen you can use the lt MODE gt or lt BACK gt buttons to choose the track number that you would like to add and press the lt GO gt button to confirm If you selected Track 1 from the previous menu you should see the following screen Total IAK 2m 52S Track 1 2m 52s e Use the lt MODE gt or lt BACK gt buttons to choose the ending track number and press the lt GO gt button to confirm You should then see a screen similar to this Total 2RR 6m 3085S Track IE 3m 37 8 f You can continue to add tracks from this disc until either you are finished or the total time equals 80 minutes by repeating Steps d e To tell the controller that you are finished with this disc use the lt MODE gt or lt BACK gt buttons to go past the last track on the disc You will see a screen similar to this Total TE 6m 30S Are you done g Press the lt GO gt button to proceed You should then see the following screen Finalize No Q h Use the lt MODE gt or lt BACK gt buttons to choose Yes or No for finalization Finalization will make your new mixed CD playable in an audio CD player but you will not be able to add any more tracks to it If you choose Yes you cannot add any more audio tracks to your selection If you choose No you can add more audio tracks from other audio CDs to your selection but you will not be able to listen to the CD until it
34. lled At power up you should see the following screen Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should then see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until you see the following screen HDD Partition Group FR Q Note In order to see the following screen you must set the CDto CD setting to No If you have not done so go to Step 1 on page 27 to change the CD to CD setting to No before proceeding any further c Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to an A as indicated in the following screen HDD Partition Group NR Q d Press the lt GO gt button once until you see following screen HDD Partition of A Bal Xx Q e Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to a B as indicated in the following screen HDD Partition of A PEB Q f Press the lt GO gt button and you will be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt 28 Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu Step 3 Load your Master disc onto the hard drive If you have already loaded your Master disc onto the hard dr
35. lows the system to copy special pre gap data in Index0 This option should be turned off unless your disc requires it Skip Read Error This setting allows you to choose what to do if a Master reading error has occurred You can abort the duplication by setting it to No You can skip the error and continue to duplicate rest of the data by setting it to Yes By turning this setting to Yes you may not get the exact same duplicates since your Master disc has errors Mode 2 Compare This setting allows the system to compare some special MODE 2 discs Since MODE 2 discs are not meant to be compared the Compare result of this type of disc may be inaccurate Power On Wait This sets the detection time for devices connected to the controller GO load trays This option is intended as a shortcut to load all of the trays at once by pressing the lt GO gt button Transfer Mode This setting sets the transfer mode between the controller and the writers Turbo Copycomp This setting enable disable the Turbo Copycomp mode Language This setting allows you to choose the language that you prefer to use when navigating the controller The standard controller supports English and Spanish Espa ol Build Information This screen shows information about the version of the software loaded onto your controller This information is needed when obtaining technical support ZY1 11 FLO ies Build 11 307 00 Startup Command
36. m can contain many images Operations such as copy load or delete all work on the image in the active slot or partition at a time To tell the controller the slot or partition for the image you need assign that slot or partition as the Active Slot or Partition Each slot or partition has a unique index ID This index ID consists of two characters like AD The first character A represents the partition group and the second character D represents the partition index for that particular group Each group holds 26 partition ranges from A to Z Normally you shall have only group A However if your hard drive has more than 26 partitions then you shall see more groups such as B C etc to hold more partitions If your hard drive has 12 partitions then you should only have one partition group A with 12 partitions inside The indexes IDs for your partitions are as follows AA AB AC AL gt 12 Partitions Total Partitions gt 12 Partitions If your hard drive consists of 60 partitions then you will have three partition groups A B or C with 26 partitions for groups A and B while only 8 partitions for group C The indexes IDs for your partitions are as follows AA AB AC AZ gt 26 Partitions BA BB BC BZ gt 26 Partitions CA CB CC CH gt 8 Partitions Total Partitions gt 60 Partitions If you want to set the partition B of group A as the active slot or partition perform the following steps The following
37. mes 228 Q 42 c Use the lt MODE gt or lt BACK gt buttons to set this option to Yes as shown in the following screen and press the lt GO gt button to confirm CD CORC Yes Q d You will then be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu Step 1 Copy your favorite tracks directly to blank CD Rs a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Use the lt MODE gt and lt BACK gt buttons to select the Edit menu and you should see the following screen Edit lt mode c Insert the audio CD with your favorite track s in the Master Reading tray and insert a blank CD R disc into one of the Writer trays Make sure no other discs remain in the rest of the trays The controller will analyze your CD and after 5 10 seconds you should see a screen similar to the following Total Oitmaa Om 00S Track aii 2m 52s Total 0 Trk represents the number of tracks selected 0 at this point 0m 00s indicates the sum of the selected track times in minutes and seconds Track 1 indicates the track that is currently selected 2m 52s indicates the length of the se
38. n your Master disc is full of scratches and your default reader tray failed to read it Use the writer tray as your Master reading source to make a quality copy and use the new copy as your new Master to make additional copies This example shows you how to select the first Writer as the source When you turn on your duplication system you should see the following screen when your controller is ready Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt 24 b Press the lt GO gt button repeatedly until the following screen is shown CDROM Drive Vaile Q These are the possible port options u Auto This selects the reader by default ATA 0 0 Reader Port Number ATA 1 0 or more Writer Port Number It ranges from 2 0 to 11 0 For this case you will choose the smallest ATA number other than ATA 1 0 1 1 ATA 2 0 is the smallest one c Use the lt MODE gt or lt BACK gt buttons to change the options until you see ATA 2 0 Once the Writer port is selected press the lt GO gt button to confirm d Then press the lt GO gt button repeatedly until the following screen is shown Setup lt mode Go gt e Once the correct drive is selected press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu You have n
39. ndicates the partition where the data will be loaded b Insert your Master disc into the top Reader tray and make sure there are no discs in the other trays Wait for 5 10 seconds and your Master disc will start to be loaded to hard drive partition B of group A partition AB Load 0302 0650 CD Load ZEE OX c Once the loading process is complete you should see a screen similar to this Pass Load 2 58 Ox u 2 33 indicates the amount of time that it took to load your disc Step 4 Return to the Copy menu a Press the lt MODE gt button once You should see a screen similar to the following Load AB0551M62 42 lt mode b Use the lt MODE gt or lt BACK gt buttons to return to the Copy menu as indicated in the following screen Copy AB0551M762 42 lt mode 21 Step 5 Starting the Copy Process Note Make sure you have taken the Master disc out of the reading tray before proceeding with the copying process Failure to do so will result in unnecessary error messages a Insert your blank discs into the corresponding Writer tray s and allow 5 10 seconds for the controller to detect your hard drive image and blank discs After your hard drive image and blank discs have been recognized you should see a screen similar to this Copy AB551M62 42 lt mode Jstart gt The AB indicates that the data is stored on partition AB The 551M indicates that a 551 MByte media is required CDROM The 62 42 indicates the
40. o alpha characters such as AD The first character A represents the partition group and the second character D represents the partition index for that particular group Each group holds 26 partitions ranging from A to Z Normally you should have only group A However if your hard drive has more than 26 partitions then you should see more groups such as B C etc to hold more partitions So if your hard drive consists of 12 partitions then you should only have one partition group A with 12 partitions inside The indexes IDs for your partitions are as follows AA AB AC AL gt 12 Partitions Total Partitions gt 12 Partitions Or if your hard drive has 60 partitions then you will have three partition groups A B and C with 26 partitions each for group A and B but only eight partitions for group C The indexes IDs for your partitions are as follows AA AB AC AZ gt 26 Partitions BA BB BC BZ gt 26 Partitions CA CB CC CH gt 8 Partitions Total Partitions gt 60 Partitions If you want to set the partition B of group A as the active slot or partition do the following Note that the following procedures only apply to duplication systems with hard drives installed At this point you should see following screen Copy lt mode 19 a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see following screen Setup lt mode go gt b Pre
41. o select the Clear menu option as shown in the following screen Clear lt mode Go gt Note You must perform the Clear function before loading your favorite tracks onto the hard drive c Press the lt GO gt button once to execute the Clear function Once the partition has been cleared you will see this message Master Cleared d You will be directed back to the Copy menu Copy lt mode e Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt f Insert CD1 into the Master Reading tray and make sure no other discs remain in the rest of the trays If your Master reading source is not the Reader make sure the Reader tray does not have any discs inside After 5 10 seconds your audio CD will be analyzed and you should see the following Total ORE 0m 00s Track 1 2m 52s 50 g When you see the above screen press the lt MODE gt button to choose track number 1 and press the lt GO gt button to confirm You should then see the following screen Total iia 2m 52s Track IE 2m 52S h Use the lt MODE gt and lt BACK gt buttons to select track number 5 and press the lt GO gt button to confirm You should then see the following screen Total ZAGR 6m 29s TrackRSE 3m 37s i To tell the system that you are finished with this disc use the lt MODE gt or lt BACK gt buttons to go past the last track on the
42. ode Go gt Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu Step 2 Specifying the Active Slot or Partition In order to delete a slot or partition on the hard drive you need to specify which slot partition you want to delete first Keep in mind each slot or partition possesses a unique index ID This index ID consists of two characters such as AD The first character A represents the partition group and the second character D represents the partition index for that particular group Each group holds 26 partition ranging from A to Z Normally you should have only group A However if your duplication system has more than 26 partitions then you should see more groups such as B C etc to hold more partitions If your hard drive consists of 12 partitions then you should have one partition group A with 12 partitions inside The indexes IDs for your partitions are as follows AA AB AC AL gt 12 Partitions Total Partitions gt 12 Partitions 32 If your hard drive has 60 partitions you will have three partitions groups A B and C with 26 partitions for groups A and B but only 8 partitions for group C The indexes IDs for your partitions are as follows AA AB AC AZ gt 26 Partitions BA BB BC BZ gt 26 Partitions CA CB CC CH gt 8 Partitions Total Partitions gt 60 Partitions If you want to se
43. om the hard drive or you want to do disc to disc duplication Setting it to Yes enables disc to disc duplication and setting it to No to copy from the hard drive Note This setting only appears if your duplication system has a hard drive installed HDD Partition Group This setting allows you to change to a different slot or partition group Note In order to change to a different slot or partition group your hard drive must have 26 partitions or more For additional information refer to Specifying the Active Slot or Partition on the Hard Drive on page 37 Note This setting only appears if your duplication system has a hard drive installed HDD Partition of X This setting allows you to change to a different slot or partition within the partition group X Note This setting only appears if your duplication system has a hard drive installed For additional information refer to Specifying the Active Slot or Partition on the Hard Drive on_page 37 56 Start Writers This setting allows you to set how many blanks have to be detected before automatically starting the copy process Write Method This setting allows you to select the duplication mode The default is Disc At Once CD Write Speed This setting allows you to adjust the direct disc to disc CD duplication speed HD to CD Write Speed This setting allows you to adjust the hard drive to disc CD duplication speed Note This setting only appears if your d
44. ow successfully set the disc reading source 25 Loading the Master Disc onto the Hard Drive The optional built in hard drive is divided into a number of partitions or slots Each partition holds one and one ONLY Master disc image regardless of the capacity of your Master disc A Master disc image is a file that contains everything on your Master disc When you load your Master disc onto the hard drive a unique image is created for that Master disc and everything you do is related to the selected image The capacity of the partition created is the same as the size of your master disc rounded up to the next Gigabyte GB The number of partitions the hard drive can hold is determined by the capacity of the hard drive and the size of the partitions created For example if you have an 80GB hard drive with a system capacity of 74GB1 You can load 74 CDs or 19 DVDs given a 4GB average capacity In order to copy from the hard drive you are required to load your Master disc onto the hard drive as an image To load your Master disc onto the hard drive do the following When you turn on your duplication system you should see the following screen when your controller is ready Copy lt mode Step 1 Make sure the Master reading source is set to the hard drive Note Make sure that the Master reading source is set to the hard drive in order to avoid unnecessary error messages To check the Master reading source press and hold the lt MO
45. percentage of a 80 minute CD that will be Used The 7start indicates the blank disc detected b Once the number of blank discs you have inserted matches the number of discs detected on the screen press the lt GO gt button to confirm and you should see a Progress screen similar to this Copy 0363 0551M CD Copy Ae 38 10X Note If the number of blank discs you have inserted does not match the number of discs detected on the screen wait 10 15 seconds for the controller to recognize all of your blank discs By manufacturer default the duplication process will begin automatically if all of the Writer trays are filled with blank media c Once the duplication run is completed you should see the following screen OK 3 NG 0 TOK 9 Copy 6 58 32X OK 3 indicates that there were three successful OK copies on this run NG 0 indicates the number of copies that were No Good TOK 9 indicates that you have nine successful copies total d Your good copies will be ejected Insert more blank discs to make more copies or press the lt MODE gt button once to return to the Copy menu Note Failed discs bad copies are not ejected automatically You will need to eject them manually and throw them away 22 Selecting the Duplication Speed This process will allow you to adjust the duplication speed subject to your various needs By default the duplication speed should be set to the optimal speed However under some circumst
46. procedures only apply to duplication systems with hard drives installed Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown HDD Partition Group 3 Q 30 Note In order to see the following screen the CD to CD setting must be set to No If you have not done so go back to last step to change the CD to CD setting to No before proceeding any further c Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to an A as indicated in the following screen HDD Partition Group FIR Q d Press the lt GO gt button once until the following screen is shown HDD Partition of A REA Q e Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to a B as indicated in the following screen HDD Partition of A l IRB Q f Press the lt GO gt Button and you will be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu You have now successfully set the partition B of group A as the active slot or partition Delet
47. s of two characters such as AD The first character A represents the partition group and the second character D represents the partition index for that particular group Each group holds 26 partition ranges from A to Z Normally you shall have only group A However if your hard drive has more than 26 partitions then you shall see more groups such as B C etc to hold more partitions If your hard drive has of 12 partitions then you will only have one partition group A with 12 partitions inside The indexes IDs for your partitions are AA AB AC AL gt 12 Partitions Total Partitions gt 12 Partitions If your hard drive has of 60 partitions then you will have three partitions groups A B and C with 26 partitions for groups A and B while only 8 partitions for group C The indexes IDs for your partitions are as follows AA AB AC AZ gt 26 Partitions BA BB BC BZ gt 26 Partitions CA CB CC CH gt 8 Partitions Total Partitions gt 60 Partitions To set the partition B of group A as the active slot or partition do the following At this point you should see the following screen Copy lt mode 37 a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown HDD Partition Group x Q c Use the lt MODE gt or
48. ss the lt GO gt button repeatedly until the following screen is shown HDD Partition Group x Q Note To see following screen you must have set the CD to CD setting to No If you have not done so go to Step I on page 19 to change the CD to CD setting to No before proceeding any further c Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to an A as in the following screen HDD Partition Group El A Q d Press the lt GO gt button once until the following screen is shown HDD Partition Group x Q e Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to a B as in the following screen HDD Partition Group El 5 Q f Press the lt GO gt button and you will be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode go gt Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be guided back to the Copy menu 20 Step 3 Load your Master disc onto the hard drive If you have already loaded your Master disc onto the hard drive then you can skip this step and go to Step 4 on page 22 At this point you should see the following screen Copy lt mode a Use the lt MODE gt or lt BACK gt buttons to scroll through the options until you see the following screen Load AB lt mode The AB i
49. t the partition B of group A as the active slot or partition do the following The following procedures only apply to duplication systems with hard drives installed At this point you should see the following screen Copy lt mode a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown HDD Partition Group FIR Q Note In order to see the following screen you must set the CD to CD setting to No If you have not done so go back to the last step to change the CD to CD setting before proceeding c Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to an A as in the following screen HDD Partition Group El A Q d Press the lt GO gt button once until the following screen is shown HDD Partition Group ies Q e Use the lt MODE gt or lt BACK gt buttons to change the X indicated in the previous screen to a B as in the following screen HDD Partition Group E B Q 33 f Press the lt GO gt Button and you will be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Then press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided bac
50. the hard drive and system buffer If you want to create a mix audio CD you must run this function first to clear the hard drive and or the system buffer before you begin Format This option erases all content on the internal hard drive 59 Chapter 6 Trouble Shooting a No display on LCD or the unit does not operate when the power is on Check to see if the power cable is connected and that the power outlet is providing the correct power u Make sure the power voltage matches the voltage of your power outlet If your outside temperature has dropped below 0 C within the past 24 hours leave the system inside a room with a temperature of 20 C or higher for four hours before powering it on for the first time b The Reader cannot read the disc and shows an error message Check the format of the Master CD DVD disc Check for the physical damage to your Master CD DVD itself Your Master disc may be copy protected Normally most of the DVDs and some of the CDs you purchase have been copy protected Use one of the Writers to read your Master disc by selecting one of Writers as the Master reading source refer to Selecting the Disc Reading Source on page 30 If it works make a copy of your Master disc and treat the copy as the new Master Then set the Master reading source back to the Reader and try again c The buttons do not function The system may be busy on a task Give it some time and press it again
51. this option to Yes as in the following screen and press the lt GO gt button to confirm CD EoReD Yes Q 45 d You will be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu Step 2 Copy Your Favorite Tracks Directly to Blank CD R a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Use the lt MODE gt or lt BACK gt buttons to select the Edit menu and you should see the following screen Edit lt mode Go gt c Insert CD1 into the Master Reader tray and insert a blank CD R disc into one of the Writer trays Make sure no other discs remain in the rest of the trays Wait 5 10 seconds and you should see the following screen Total ORRAK Om 00S Track 1 2m 52s d When you see previous screen you can use the lt MODE gt or lt BACK gt buttons to choose the track number that you would like to add and press the lt GO gt button to confirm If you selected Track 1 from the previous menu you should see the following screen Total IR 2m 52S Track 1 2m 52s e Use the lt MODE gt or lt BACK gt buttons to choose the next track number you would like to end and press the lt
52. ttons to set this option to No as in the following screen and press the lt GO gt button to confirm 1 There are many factors that contribute to the capacity difference between the advertised capacity and the actual capacity a hard drive Manufacturers use a conversion rate of 1GB 1 Billion Bytes or 1000 3 Bytes However most Operating Systems including our controller use the standard conversion rate of 1GB 1 074 billion bytes or 1024 3 Bytes Therefore for an advertised 80GB hard drive 80 Billion Bytes the duplication system capacity is actually 74 5 billion bytes 74 5GB m In addition we round off all fractions of a GB to the lower whole number That means for a hard drive that has a 74 5GB system capacity we only recognize and use 74GB 18 CD to CD No Q d Then you will be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see following screen Setup lt mode Go gt Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will be sent back to the Copy menu Step 2 Specify the Active Slot or Partition Note If you have already loaded your master disc onto the hard drive then you can skip this step and go to Step 4 on page 22 In order to load your Master disc onto the hard drive you need to specify the slot partition where you want it loaded Each slot or partition possesses a unique index ID This index ID consists of tw
53. uplication system has a hard drive installed DVD Write Speed This setting allows you to adjust the direct disc to disc DVD duplication speed Note This setting only appears if your duplication system is a DVD duplication system HD to DVD Write Speed This setting allows you to adjust the hard drive to disc DVD duplication speed Note This setting only appears if your duplication system is a DVD duplication system AND it has a hard drive installed CD ROM Drive This setting allows you select the default reading device for disc to disc duplication For additional information refer to Selecting the Disc Reading Source on_page 30 CDDA Load Speed This option sets the loading speed when reading a Compact Disc Digital Audio disc Audio CD Audio CDs sometimes need to be read at slower speeds than digital CDs to endure accurate reproduction Eject Disc This setting allows you to choose at what kind of situation you want the trays to be ejected Buzzer This option selects whether the buzzer in the duplication system sounds when pressing a key CD G This setting allows you to enable or disable duplication of CD G discs Note In order to duplicate CD G discs your Writer drive needs to support CD G CD 57 CopyComp Eject This setting allows you to choose whether you want the trays to be ejected between the Copying and Comparing process when you perform the Copy Comp operation Read CDDA Index0 This setting al
54. ure you have taken the Master disc out of the Reading tray before proceeding with the copying process Failure to do so will result unnecessary error messages b Press the lt GO gt button to confirm and you should see the following Progress screen Copy 0363 0551M CD Copy ZNEE 10X The numbers in the top line indicate that 551 MBytes M out of the total 0363M have been copied so far The CD on the right hand side indicates that the source media is a CD ROM The numbers in the center of the bottom line indicate the time since the copy operation started The 10X indicates the copy speed If the number of blank discs you inserted does not match the number of discs detected on the screen wait 10 15 seconds for the controller to recognize all of your blank discs 53 c Once the duplication run is completed you should see the following screen Ok 3 NG 0 TOK 9 Copy 6 58 LOX OK 3 indicates that there were two successful OK copies on this run NGO indicates the number of copies that were No Good TOK 9 indicates that you have nine successful copies total d Your good copies will be ejected Next insert more blank discs to make more copies Or you can press the lt MODE gt button to go back to the Copy menu Note Failed discs bad copies are not automatically ejected You will need to manually eject them in order to continue 54 Chapter 5 Menu Overview Main Menu Overview Following are
55. will then be guided back to the Copy menu If not press the lt GO gt button repeatedly until you see following screen Setup lt mode Go gt e Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You will then be guided back to the Copy menu Step 2 Specify the Active Slot or Partition a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Press the lt GO gt button repeatedly until the following screen is shown HDD Partition Group es Q c Use the lt MODE gt or lt BACK gt buttons until the X on the previous screen shows A as in the following screen HDD Partition Group l A Q d Press the lt GO gt button once until the following screen is shown HDD Partition of A IRS Q e Use the lt MODE gt or lt BACK gt buttons until the X on the previous screen shows B as in the following screen HDD Partition of A bel B Q 49 f You will be directed back to the Copy menu If not press the lt GO gt button repeatedly until you see the following screen Setup lt mode Go gt Step 3 Load Your Favorite Tracks onto the Hard Drive a Press and hold the lt MODE gt button for three seconds and release it after a beep has sounded You should see the following screen Setup lt mode Go gt b Use the lt MODE gt or lt BACK gt buttons t
56. y active partition on the hard disk where XX equals the corrently set partition and group see Specify the Active Slot or Partition on page 22 The partition is selected using the Setup HDD Partition Group and command Compare This menu will guide you to perform a bit by bit comparison between the Master reading source and all the copied discs inside the Writer tray The purpose to perform this compare operation is to ensure all of your copies have the exactly same information as your Master reading source 55 Quick Erase This menu will guide you to erase any rewriteable discs in the Writer Tray Verify This menu will guide you to perform disc readability checks This operation will check the readability of your Master discs and the copied discs The purpose to perform this verify operation is to ensure all of your copies are readable Advanced Menu Overview The following menus are for advance users To navigate them you need to press and hold the lt MODE gt button for three seconds from the basic menu Setup This menu contains various settings for your system Unless you have been told to do so we strongly suggest you do not touch them unless they have been mentioned in this user manual Following are some settings you might encounter However for those settings not displayed as follows we strongly suggest you do not adjust them CD to CD This setting is the key option to determining whether you want to copy fr
Download Pdf Manuals
Related Search