Valhalla Scientific Inc. G6 Duo User Manual
Contents
1. Spanish Espa ol Portuguese Portugu s German Deutsch French Fran ais Italian Italiano 13 Section VI Maintenance Calibration Before calibrating your G6 DUO you will need a reference weight between 200 and 350 Lbs The scale can be calibrated using lower weights However to insure linearity of the measurements we recommend the above listed weight range as a calibration reference Press 9 to access Menu Menu Password PW 7538 When prompted MENU press the 9 The screen will display CAL Y N Press the YES key to start calibration NO to cancel When prompted ZERO CAL remove any weight from the scale and press ENTER d er dE The scale will calibrate the zero reference as it counts down from 10 to 0 5 When prompted WGT ON place a weight on the scale and press ENTER The scale will calibrate the weight reference as it counts down from 10 to O 6 When prompted CAL WGT type the value of the weight applied to the scale and press ENTER Note always enter the value in a 4 digit format Example 200 Lbs enter 2000 or 309 2 Lbs enter 3092 7 The screen will display the cal factor Press ENTER 8 CAL DONE Zero Calibration Press O when scale is idle to reset any zero offset For additional information Call 1 800 548 9806 Visit our Website at www bodycompscale com 142. Recall the Last Measurement The G6 DUO models allow the user to recall the last measurement and reprint it To recall the last results 1 Press the RCL button on the display panel The data will be displayed The display clears after about 15 seconds or can be cleared by pressing the CLR button 2 Toprint the results select graphic or plain and press ENTER The last results are erased if the scale is turned OFF Section III Printouts When the results are displayed the G6 allows you to select the print type Plain or Graphic Plain Printouts The Plain printout type is a single page containing all the results from the measurements and calculations Programming Number of Copies The user can pre define the number of copies of this print out to print The default value is 1 To change the value 1 Without stepping on the scale Press 3 to access Settings Menu Menu Password PW 7538 When prompted MENU press Plain Enter the number of copies you wish to print Wait for the scale to return to standby Graphic Printouts The Graphic printout type is a multi page printout designed for specific preprinted paper The G6 Duo scale uses 2 types of Graphic printouts a 5 page for adults and a 7 page for children Make sure that the printer is loaded with the appropriate paper before printing ion SIZE ao h ee E m J f masy IPO AA SE eri Adults IPO en pow scat Section IV Spe
3. Valhalla Scientific Inc G6 Duo User Manual Rev 2 41 Table of Contents SOC EON RS AAC E E E T N E OEE NEE EEN ON 3 Receiving and Inspection AAA 3 edade AAE 3 Connecting Scale TOP eia dl AAA 3 PONS LIRE aA 4 Matching the Scale to a new HP6100 Printer sise 5 How to Identify Firmware Revision and Serial Number 5 SECUON BU bagil eie daiela 6 How to Take a Measurement dE 6 How to Recall the Last Measurement siens 7 ede diela Ba b diada D ea 8 BL LUS PINTOU PP EEE 8 Programming Number of Co EEA 8 Graphic PUI zele 8 S CUHON IN Special A ala 10 JAN ziza Only Aaa 10 ugalde Mele 10 Body Suarez 10 Section CIS TONNE e E E E E E E 11 OIG TON AAA 11 PVC OI eie diat AAA 11 b 6 F SEA 11 Salezan NO BU Oil AEA 12 Disabling Enabling the Calorie DOOR 12 ENS OO a A de a ce 200107 13 Section V Aziak aer 14 CD AO ee PARADE AGIR MRCA 14 FOTO Dr O ee i 14 Section I Installation Receiving and Inspection The G6 DUO has been thoroughly inspected and tested at the factory prior to shipment If shipping carton damage is apparent when the unit is received the carrier agent should be present when the unit is unpacked Retain the shipping carton for carrier inspection Take pictures of the box and damage Call 800 548 9806 and Valhalla will issue a UPS return Call tag DO NOT return the unit to the Valhalla Scientific factory before an authorization number has been obtained Storage The G6 DUO should be stored in a temperature r
4. ange of 50 to 90 F Exposure to extended periods of heat or cold may result in component damage or possible failure Connecting Scale to Printer Connect the G6 DUO USB printer port located on the back side on the scale base to the HP printer via the provided USB printer cable Powering up Before plugging the adapter into the wall verify that the power switch located on upper part of the neck is in the OFF position Connect the power supply to the wall socket and then to the scale e The power supply receptacle is located on the lower part of the neck Once the connection is made flip the switch to the ON position The display should briefly display a start up message which will include the Model Number and the Firmware version installed CE EE Gyan BMI PERCENTILE Kg cm o Female RESTING ENERGY EXPENDITURE e Lbs Ft O Male Yes A A EDE DDD 650500 UNDERWGT HEALTHY ATRISK HIGHRISK CE BodyCompScale com gt i z da O o Graphic G600O Valhalla Scientific 800 548 9806 The startup will be followed by a synchronization countdown Once the display goes blank the scale is ready to be used Matching the Scale to a new HP6100 Printer To match your new HP6100 printer to the scale perform the following steps wW N de ek 10 11 Make sure the printer is ON and connected to the scale Make sure the printer has finished its
5. automatically return to Standard Mode measurements 10 Section V Customizing Lock Option The Lock option allows you to lock the G6 DUO and prevent it from being used by unauthorized people When the G6 DUO is locked you will be required to enter an authorization ID before each test To enable the Lock feature 1 Press 3 to access Settings Menu Menu Password PW 7538 2 When prompted MENU press 9 The screen will display PIN Y N 3 Press the YES key to enable the Lock Pin Option NO to cancel The default authorization ID number is 1234 The ID can be changed at any time To change the Authorization ID Number Press 9 to access Maintenance Menu Menu Password PW 7538 When prompted MENU press 1 Enter PW 1973 The screen will display NEW PIN 3 Enter the new 4 digit ID Print Ohms Option The Print Ohms option gives you the choice of whether or not to print the measured bio impedance value on the printouts When you first receive the G6 DUO the Print Ohms function is set to OFF To enable the printing of the Ohms measurement 1 Press 3 to access Settings Menu Menu Password PW 7538 2 When prompted MENU press 5 The screen will display OHMS MODE Y N 3 Press the YES key to enable the Print Ohms Option NO to cancel Physician ID The G6 DUO allows the user to set a physician s ID The ID can be a number up to 8 digits and if set will be printed on the prin
6. cial Modes Weight Only Mode The G6 DUO allows you to take weight only measurements To enable this measurement mode Press Weight Only before stepping onto the scale The scale will display WGT ON Step on the scale and press Enter The display will count down from 5 to 1 and display your weight To clear the weight Press CLR Athletic Mode To qualify as athletic the subject must meet the following requirements Work out 40 minutes in duration 20 min aerobic 20 min anaerobic 3 days a week for at least the last 6 months In order to enable the Athletic Mode predictive equation 1 Before stepping on the scale Press 7 The screen will display ATH MODE Y N 2 Press the YES key to enable the Athletic Mode equations NO to cancel These steps will enable the Athletic Mode for a single use After the test is performed the G6 DUO will automatically return to Standard Mode measurements Body Builder Mode To qualify as a bodybuilder the subject must be at least 20 above their ideal weight as defined in the Metropolitan Height Weight chart and that weight must be primarily muscle mass In order to enable the Bodybuilder Mode predictive equation 1 Before stepping on the scale Press 8 The screen will display BB MODE Y N 2 Press the YES key to enable the Body Builder Mode equations NO to cancel These steps will enable the Bodybuilder Mode for a single use After the test is performed the G6 DUO will
7. e a Measurement Attention Model G6 Duo requires that the user removes shoes and socks before standing on the scale 1 Stand on scale Stay still while the G6 DUO measures your weight 2 When prompted enter the Age For children 4 to 17y11m the age must be entered in Years and Months From 4 to 9 you will need to press enter after the year is entered from 10 to 17 the scale will automatically skip to the month s section For Adults 18 to 99 no months are required Press the flashing ENTER button to confirm 3 The G6 DUO will prompt you to enter the Height The height may be entered in several formats A height of 6 feet 2 inches can be entered as 6 0 2 or 6 2 The button is used to add a half inch to the height For example 5 feet 7 5 inches is entered as 5 0 7 or 5 7 1 2 If a wrong number is pressed press CLR clear to start over Press the flashing ENTER button to confirm the height and move to the next step 4 When prompted enter the Gender Select Male or Female and press the flashing ENTER button to confirm selection 5 When prompted grip the side handles so that the palm of each hand makes contact with both handles on both sides of the display module The thumb should rest gently on top of upper handle The G6 DUO will now measure your bio impedance display the results 6 To print the results select graphic or plain and press ENTER See Section III Printouts for details on the print types How to
8. power up routine Make sure the printer has paper loaded Without stepping on the scale Press 9 to access Maintenance Menu Menu Password PW 7538 When prompted MENU press 7 The screen will go blank Press the RCL button on the display panel The data will be displayed Press the Plain button followed by the Enter button The display will flash PRNT PLS WAIT for approximately 30 seconds At this point the default printer settings have been cleared Without stepping on the scale Press 9 to access Maintenance Menu Menu Password PW 7538 When prompted MENU press 7 The screen will go blank Press the RCL button on the display panel Data will be displayed Press the Plain button followed by the Enter button The display will flash PRNT PLS WAIT for approximately 30 seconds At this point the new printer settings have been installed and the printer should have printed a test page with all zeros How to Identify Firmware Revision and Serial Number To identify your G6 DUO press 4 The BMI Percentile window will display the firmware version The REE window will display the scale type The serial number of the scale can be found on the serial tag sticker located under the head of the scale or on the display 1 Press 9 to access Maintenance Menu Menu Password PW 7538 2 When prompted MENU press 8 The screen will display the serial number Section II Operations How to Tak
9. touts under Prepared By To set the Physician ID 1 Press 5 before stepping on the scale The screen will display ID 0000 0000 2 Enter the preferred ID up to 8 digits and press ENTER The Physician ID can be changed or reset at anytime 11 Patient ID Option The Patient ID option gives you the choice of using a Patient ID with every test When you first receive the G6 DUO the Patient ID function is set to OFF To enable the Patient ID Option Press 2 to access Settings Menu Menu Password PW 7538 When prompted MENU press 4 The screen will display ID MODE Y N 3 Press the YES key to enable the Patient ID Option NO to cancel Disabling Enabling the Calorie Option Disabling the calorie option will prevent the scale from displaying and printing REE and activity level burn rates To disable the Calorie Option 1 Press 3 to access Settings Menu Menu Password PW 7538 2 When prompted MENU press 8 The screen will display CALS Y N 3 Press the NO key to disable the Calorie Option Yes to Enable 12 Language Option The Language option gives you the choice of selecting the language of the printouts To set the language Press 3 to access Settings Menu Menu Password PW 7538 When prompted MENU press 3 The screen will display NEW LANG Enter the number associated with the language you wish to choose dd T 2 language Available SAI LZ es English ri
Download Pdf Manuals
Related Search