Wireless Motion Alert R
Contents
1. 4 Slide the switch towards the power jack to increase the volume 5 Slide the switch towards the antenna jack to decrease the volume 6 Snap the case back together 7 Plug in the power supply and antenna Volume Lower Higher M nr Changing the volume level Motion Alert 30058 37058 Page 6 Optional Accessories The Long Range Antenna increases the range of the Motion Alert system up to double the regular range The Plug In Siren increases the sound output of the Motion Alert re ceiver Driveway Monitor wirelessly detects a vehicle coming up your drive way Simply put this product by the side of the driveway and when a ve hicle goes by the receiver will signal you inside your home or office You can use multiple sensors with one Motion Alert receiver Each type of sensor will produce a different chime from the receiver when triggered You can also have several Motion Alert sensors or Motion Alert receivers work together as a system ITEM Part Price Long Range Antenna 30316 49 95 Plug In Siren 30319 19 95 Driveway Monitor Sensor 30075 129 95 Additional Motion Alert Sensor 30067 49 95 Additional Motion Alert Receiver 33333 59 85 All prices are in US dollars and include shipping and handling Contact your local distributor or call DesignTech to order This device complies with FCC Rules Part 15 Operation is subject to two conditions 1 This device may not cause harmful interference and 2 it must2. Trouble Shooting 1 False Activations or Not Activating When It Should If you get false activations or if your motion sensor sometimes does not activate you can change the motion sensor s sensitivity level If you get false activations when the motion sensor has not been moved you may want to change the sensitivity setting to the Low Sensitivity Alarm mode If on the other hand your unit sometimes does not activate change the sen sitivity level to the High Sensitivity Alarm mode Movements of large metal objects near the motion sensor will often cause false activations To avoid this problem change the sensor s sensitivity level to the lower setting A weak battery may also cause false activations or missed detections The lithium battery in the Motion Alert sensor must be replaced every 1 to 2 years depending on the sensitivity setting 2 Insufficient Range If your Motion Alert system works when the motion sensor is close to the receiver but not when the motion sensor is far away the following adjust ments may improve the range of the system e Move the receiver to a room closer to your motion sensor If the motion sensor is located outside place the receiver on a window sill that faces the monitored object or on a table close to the window so that the moni tored object is visible from the receiver antenna e Move the receiver farther away from computers CD players and cordless phones These items may interfere with the o
3. accept any interference received including that which may cause undesirable operation FCC ID ELGMOTION amp ELGHOME DOC 1476 102 203 and 1476 102 203A User is cautioned that changes or modifications not expressly approved by DesignTech could void the user s authority to operate this equipment Covered under US Patent Numbers 4 851 775 amp 5 239 264 a Designiech A INTERNATIONAL ING 7955 Cameron Brown Court Springfield Virginia 22153 USA Tel 703 866 2000 or 800 337 4468 www designtech intl com 2000 DesignTech International Inc Page 7 Motion Alert 30058 37058
4. 058 37058 5 Sound Notification for Two or More Sensors For each additional sensor learned the receiver sounds two or more extra beeps when these sensors are triggered These additional beeps indicate the order in which the sensor was learned The original sensor beeps the one alarm or chime sound when triggered The second learned sensor gives two extra beeps before the chime or alarm sound the third sensor learned gives three extra beeps etc 6 Temporarily Silencing the Receiver Sometimes you may wish to silence the receiver for several hours as you work on the object that is being monitored To silence the receiver for up to ten hours 1 Press and hold the ALERT light until you hear a steady tone 2 The silenced sleep state is indicated by alternating short blinks of the red and green lights for ten hours or until reset 3 To resume normal operation press the ALERT light again briefly NOTE A power failure will cancel the sleep mode 7 Adjusting the Volume The receiver has two volume settings for the notification beep The re ceiver is factory set to the highest setting To lower the volume setting Unplug the power supply and antenna from the receiver 2 Use a small screwdriver and carefully pry open the receiver case often carefully prying the case open at the antenna jack area works best 3 When the top of the case is removed you will notice a small slide switch between the antenna jack and the power jack
5. ate the new sensor by rotating the sensor until you hear a war bling chirp If you hear three separate chirps like a small bird the receiver already has that sensor learned in memory 6 When all sensors have been learned press the ALERT light briefly you should hear several short beeps and the receiver resumes normal operation or simply wait an additional 60 seconds and the receiver automatically exits the programming mode Clearing the Receivers Memory and Re learning All Sensors 1 Unplug the power supply of the receiver 2 Wait five seconds and then plug it in again 3 Wait until the receiver has finished beeping during its powering up sequence and the green light goes out for a few seconds While the green light is still out promptly hold down the ALERT light for about 5 seconds until you hear a steady tone When you release the ALERT light you will hear five more beeps to indicating that the memory is now empty 4 The green power light will start to flash indicating the receiver is in code learning mode You now have sixty seconds to learn the code of the new sensor 5 Activate the new sensor by rotating the sensor until you hear a war bling chirp 6 When all sensors have been learned press the ALERT light briefly you will hear several short beeps and the receiver will resume normal operation or simply wait an additional 60 seconds and the receiver will automatically exit the programming mode Page 5 Motion Alert 30
6. peration of your Motion Alert system if you place the receiver too close to them e Moving the antenna 45 to the left or right of vertical will sometimes im prove the range of the system e An optional long range antenna is available see Optional Accessories Section which gives the system up to double the regular range 3 Green Light Blinks Continuously If the green light blinks continuously the system is in sensor learning mode Simply push the ALERT light It will now be in normal operation mode Motion Alert 30058 37058 Page 4 4 Sensor Learning do only if receiver does not respond to the sensor There are two ways to teach new sensors to the receiver The first adds new sensors to the receiver Existing sensors will still work with the re ceiver The second procedure erases all learned transmitters and allows the user to re teach new sensors to the receiver Adding New Sensors without erasing the original sensors 1 Unplug the power supply of the receiver 2 Wait five seconds and then plug it in again 3 Wait until the receiver has finished beeping during its powering up sequence and the green light goes out for a few seconds While the green light is still out promptly press and hold the ALERT light You should hear a few short beeps Release the light 4 The green power light should flash indicating the receiver is in code learning mode You have sixty seconds to learn the code of the new sensor 5 Activ
7. re than 5 feet away from the receiver The receiver will chime twice and the red ALERT light will flash until you push the ALERT light If the receiver does not chime or the red ALERT light does not come on first check that the green POWER light on the receiver is on and that the battery are inserted correctly in the sensor If the receiver still does not respond see the Sensor Learning section under Troubleshooting ventilation hole Mounting the Sensor es Attach the sensor to whatever object you want to Ce monitor by using the double stick foam tape provided amp or two screws Do not cover the small ventilation amp hole on the back of the sensor e How Motion Alert Works The sensor uses a patented magnetometer sensor system Rotating the sensor any which way will trigger the unit Moving any large metal object next to the sensor will also trigger the unit Rotating motors in close prox imity will also trigger the sensor The receiver chimes and the red ALERT light flashes when the sensor is triggered The red ALERT light continues to flash until the red ALERT light is pressed You can stop the red ALERT light from blinking by pressing the flashing red ALERT light However the receiver will chime each time the sensor is moved even if the system is not reset each time Motion Alert 30058 37058 Page 2 The range of the Motion Alert system varies Line of sight the Motion Alert sensor should work up to 500 feet away f
8. rom the receiver when mounted in a typical environment around a home The system will work up to 1 000 ft away when placed 5 ft or higher off the ground and within line of sight of the receiver If you do not have enough range see the section on Insufficient Range on page 4 Changing the Sound The sensor comes factory set to the doorbell mode This setting is de signed for swinging door type applications The receiver will emit a ding dong chime sound each time that the sensor is moved The other setting is the Alarm mode The receiver will emit a warble sound every time that the sensor is moved The receiver will emit this sound once very 5 seconds for 25 minutes or until the ALERT light is pressed The Alarm mode has a low and high sensitivity setting The Low Sensitiv ity Alarm mode requires more movement of the sensor than the High Sensitivity Alarm mode to activate woe rN sA You will need to experiment with a y om your application to see which C i p tes setting is best for you Open the oe a Ah saad es ete motion sensor case and use the C eg l adjacent diagram to adjust the Ch Doorbell Chime setting Factory Setting a High Sensitivity Alarm Note The Motion Alert s Battery Life is affected by these settings Low Sensitivity Alarm mode 2 years battery life Doorbell Chime mode 11 2 years battery life High Sensitivity Alarm mode 1 year battery life Page 3 Motion Alert 30058 37058
9. v0 2 User s Manual Wireless Motion Alert Model s 30058 and 37058 DesignTech s Motion Alert sends a wireless signal to alert you when the sensor has moved Contents E tia iy F Red Alert gs Light amp Reset Lithium Battery Indoor Receiver Button CR2032 type i white Sensor black Ea ie aL Two Screws for Double Stick mounting Se sf Foam Tape Antenna AC Adapter Installing the Battery in the Motion Sensor 1 Insert a small coin or screwdriver blade into the slot at the side of the case and gently twist to open the case 2 Insert the the lithium battery into the battery clip with the side face up Battery 3 Push the case back together tightly squeezing slowly with force for 5 seconds to firmly seal the waterproof case Page 1 Motion Alert 30058 37058 Setting Up the Receiver 1 Plug the AC adapter into any standard electrical wall outlet and the other end into the back of the receiver The green POWER light will blink on for a second and the receiver will chirp The green light will go out for 5 seconds then come back on LF ready for normal operation w 2 Motion Alert comes with a 9 inch antenna which plugs into the antenna jack on the back of the receiver The antenna should be vertical Testing the System Prior to Installation 1 The sensor and receiver are factory set to a unique code Before install ing the sensor outside test the unit by rotating the sensor mo
Download Pdf Manuals
Related Search