HuddleCamHD 20X User Manual
Contents
1. Installation Screw 1 USB 3 0 Data Cable 3m Serial Control Cable RS 232C to RS 485 Adapter IR Remote Controller 1 User Manual 1 Ver 1 2 8 15 U HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Physical DescriptiOn eee eee e re ere eee ee eee e rete esee eese teas E 1 Lens 2 IR Receiver To receive IR remote controller signal 3 Power LED Blue LED lights when unit is powered and on 4 Stand by LED Orange LED lights when unit is powered and in standby 9 IR Receiver To receive IR remote controller signal Ver 1 2 8 15 UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 By RE di m 10 DGIN12 VN EE Hey USB 3 0 Interface For connection to PC USB 3 0 port also compatible with USB 2 0 port and driver IR Selective Switch When using only one remote to control more than one camera this switch will assign a unique ID to each camera VISCA IN Port For hard wired remote control from a 3 party PC joystick etc VISCA Out Port RS485 Used for daisy chaining multiple cameras for RS 232 RS 485 control DC IN 12V Socket Only use the Power Adapter supplied with this camera Ver 1 2 8 15 UA j HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Uoc l 1 Dip Switch Used for2. Swap between different formats 7 Power Supply Switch Switch for turning camera on i e Stand By mode vs Working mode 8 OSD Menu Zone Dome OSD Enter Pan Tilt Zoom OSD menu Lens OSD Enter lens OSD menu 10 11 9 Slow Zoom In Out Zone Zoom in slowly 6 Zoom out slowly 10 Focus Control Zone Auto Turn on auto focus Manual Turn on manual focus Far Set focus at farther distance Near Set focus at nearer distance Ver 1 2 8 15 UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 11 Pan Tilt Function Zone L Limit Set left boundary limit scanning position Scan Enable Boundary Scanning Auto Panning R Limit Set right boundary limit scanning position Home Go to camera s Home position Tour Enable automatic patrol tour of presets Rev Enable image flip for ceiling mounting Connection INSCIFUCTIONG ccccccccsccsccsccsscecceccesccsccscceccescescescescescsscesccescs 1 Connect included Power Supply to the camera 2 Wait for camera to come to Home Position 3 Connect included USB 3 0 cable to camera and USB 3 0 port of PC unit is also backwards compatible with USB 2 0 port 4 Select and configure camera in your software of choice NOTE Failure to follow this sequence may result in no connection to PC Care Of The Unit cc lleeee eee eere eee eren eere en ree n teen eee ee stehen eerte i Remove dust or dirt on the
3. 8 15 U HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 GN ae op che ee On Screen Display Menu Use the OSD menu to access and change the camera s settings Note You cannot manually move the camera pan tilt when the OSD menu is visible on the screen The Dome OSD Menu is as follows Pan Speed Default Value o Set speed of Pan motor Range 1 63 Tilt Speed Default Value o Set speed of Pan motor Range 1 63 Scan Speed Auto Pan Mode Default Value o Set speed of boundary scan Range 1 63 Tour Path uses presets Default Value o Select desired tour path Range 1 4 Tour Dwell Default Value o Set duration to dwell on each preset Range 1 60 Proportion Default Value o Set Proportion Range On Off Auto Rev Default Value o Set camera mounting orientation N for inverted ceiling mount Frame Default Value o Set Refresh Rate Range 50Hz or 60 Hz Ver 1 2 8 15 20 20 On 60Hz UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 The Lens OSD Menu is as follows BACKLIGHT o ON OFF SATURATION o 0 15 SHARPNESS o 0 15 NR Noise Reduction o Adjustable Value Off 1 4 WB White Balance Default Value OFF Default Value O Default Value 3 Default Value Auto Default Value Auto o Auto Manual Outdoor Indoor One Push ATW
4. Cisco Systems VPN Adapter for 64 bit Windows a Dell Wireless 1540 802 11a g n 24GHz 5GHz EF Intel R 82579LM Gigabit Network Connection 2 Microsoft Virtual WiFi Miniport Adapter LAMP TAP Win32 Adapter V9 gt S Ports COM amp LPT b n Processors b amp Sound video and game controllers bS Storane controllers In this example you can see the HuddleCam model in use connected as a fully functional USB 3 0 device HuddleCamHD as well as a USB 2 0 device with limited functionality USB2 0 Camera If your device has not connected to or has not recognized the HuddleCam as an imaging device in which case you may see a new unknown device Westbridge or CYTFX3 labeled device show up in Device Manager s Universal Serial Bus Controllers section rather than in the Imaging Devices section the HuddleCam will not be available to programs that utilize a camera In this case try restarting the device and reconnecting the camera via USB USB 2 0 or USB 3 0 depending upon HuddleCam model Ver 1 2 8 15 UA j HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Similarly you can see a connected device in System Information on a MAC See screenshot below eoe Mac min Hardware USB Device Tree ATA USB 3 0 Hi Speed Bus Mucio Bluetoo Camera Card Reade Ether ard Fire Wi Grapl Displa Hardware RAID Memor D i Al li PCI BRCM20702 Hub Para
5. Silver Gray 32 F to 113 F 0 C to 45 C 14 F to 140 F 10 C 60 C Indoor only
6. selecting baud rate and the remote signal output switch 2 Tripod Will accept 1 4 20 bolt from 3 party tripod wall or ceiling mount Ver 1 2 8 15 uA j HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 4 Dip Switch Se ttiNGS ccccccsssscccsssscccssssccccsssccccsssccccssssscccsscccccsscesscssees Note When changing Dip Switch settings make all changes with camera powered off Dip Switch 1 To set communication baud rate Dip Switch 2 To set control protocol Dip Switch 3 Set only for firmware upgrading Dip Switch 4 amp 5 To set camera s RS232 RS485 ID number for daisy chain wired control Camera address code settinc uu i Ver 1 2 8 15 HuddleCamHD i 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Cable Connection INFO cccccsscccsccccsccccscccsscccsscccscccsscccssccscccsscccescceess VISCA RS 232C IN ReferenxcCe eere eee rennen erento entree eor eennue VISCA RS 232C IN PinSiN Function 7 101 DRN 2 DSRN 83 4TXIN J 8 OOO 6 104 GND 5110 009 3 s Ron 2WIO9g7 1 s omo OUTPUT 8 No Connection _ _ VOCA ISI A UE RETO ENC eee ee eee ene ee VISCA RS 232C OUT 1 2 T 8 OO ON6 fl S O 09 J 3 re 2 OO 1 SS o Q RS 485 Ver 1 2
7. surface of the lens with a blower commercially available Ver 1 2 8 15 U HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Installation INSCFUCTIONG ccccsccssscssccssccsscsscccsscccccescceccceccssccesccescesscees Desktop InstallatiOn 11 eee eee eee e eene rr eer eee rene teen rere o ouue When using the HuddleCam on a desk Make sure that it will stand level If you want to use the camera on an incline make sure the angle is less than 15 degrees to ensure that the camera s pan and tilt mechanism operates normally When using the HuddleCam with a tripod screw the tripod to the bottom of the cam era The tripod screw must fit below specifications Note Tripod must stand on a level surface 1 4 20UNC gt Qzb mm Ver 1 2 8 15 HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Ceiling MOUNL cccccsscccssscccssscccsscccssscccsssccssscccsscccssccccssccccsscccssscccssccecsccssess Step 1 Ceiling Bracket ag o Ceiling For hard ceilings Use the supplied plastic anchors and screws to fix the ceiling bracket to the ceiling For acoustic tile ceilings cut a piece of plywood 12 x 23 75 to use as a tile bridge above the ceiling tile Use the supplied screws without plastic anchors to fix the ceiling bracket to the pl
8. Manual Settings R GAIN Red Gain o Adjustable Scope 0 255 B GAIN Blue Gain o Adjustable Scope 0 255 AE Auto Exposure Default Value 64 Default Value 84 Default Value Auto o Auto Manual Shutter Iris Bright Manual Settings SHUTTER Default Value 1 1 o Shutter Speed Range 1 1 1 10000 IRIS o Close F1 4 f22 BRIGHT o Set Brightness O 31 Ver 1 2 8 15 Default Value Close Default Value O U HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 IR Remote Controller Note Some buttons do not operate for all camera models 1 Reset Restarts the camera and restores it to Factory Default settings Note Will delete all memory 1 2 Camera Selection Select Camera ID 1 2 or 3 2 3 Preset Positions 1 9 Preset Positions Set Setting Preset Position Clear Clear Preset Position Call Call Preset Position Note If you want to set or call the first preset position to 1 you should press 3 number key 1 then press Set or Call to set call the position 4 Fast Zoom in out Control Zone Zoom in quickly Zoom out quickly J Pan Tilt Controller t Move Up Move Down 4 Move Left Move Right Auto Pan 6 Additional Function Zone Freeze Image Freeze BL Back light Compensation WB White Balance AE Auto Exposure 5 D Zoom Digital Zoom HDMI Swap to HDMI video output DVI Swap to DVI video output Format
9. UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 HuddleCamHD 20x USB 3 0 PTZ CAMERA INSTALLATION amp OPERATION MANUAL IR POWER STANDBY UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 PFOECAUTTONG ccccccsccsccsscescesccsccesceccecceccesccscceccecceccescesccscceccsccescescescesceeccescs Be o tt Please read this manual carefully before using the camera Avoid damage from stress violent vibration or liquid intrusion during transportation storage or installation Take care of the camera during installation to prevent damage to the camera case ports lens or PTZ mechanism Do not apply excessive voltage Use only the specified voltage Otherwise you may experience electrical shock Keep the camera away from strong electromagnetic sources Do not aim the camera at bright light sources e g bright lights the sun etc for extended periods of time Do not clean the camera with any active chemicals or corrosive detergents Do not disassemble the camera or any of the camera s components If problems arise please contact your authorized dealer After long term operation moving components can wear down Contact your authorized dealer for repair iini Supplied Equipment HD Color Video Camera 1 12V 2 0A DC Power Adapter 1 Installation Bracket 1
10. ad Try new USB Cable to the PC via USB Camera connects Connect USB only after sometimes camera has completely booted tilt and or zoom displayed on the screen menu limit was reached the other direction Remote control not The camera select Choose the correct IR working button on the remote select number to match control is not set to match camera settings the IR select switch number set on the camera Camera cannot be The connection between Refer to Cable Connection controlled via VISCA the PC and camera is Info section of this incorrect manual Commands being sent are Refer to VISCA manual incorrect The Camera is not No response or image Disconnect power and working at all from camera wait a few minutes then connect the power again Retry Ver 1 2 8 15 UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Important Notes Regarding USB Connectivity USB 3 0 ports are backwards compatible with USB 2 0 devices USB 2 0 ports are not completely forward compatible with USB 3 0 devices some USB 3 0 devices will connect to USB 2 0 with limited functionality External USB hubs should be avoided i e give the camera its own USB port on the device as they are not well suited to transmitting HD video reliably USB extension systems must be fully compatible with the version of USB that you are using and must utilize an external powe
11. llel SCS Bluetooth USB Host Controller Powe IF Receive In this example you can see the HuddleCam model in use connected as a fully functional USB 3 0 device HuddleCamHD as well as a USB2 0 camera with limited functionality USB2 0 camera Ver 1 2 8 15 Model Number HC20X GY G2 Camera amp Lens e Video CMOS Sensor Frame Rate Lens Zoom Field of View Min Lux Warranty Pan Tilt Movement e Pan Movement e Tilt Rotation e Presets Rear Board Connectors Video Interface Control Signal Interface Control Signal Config Baud Rate Power Supply Interface Electrical Index e Power Supply Adapter e Input Voltage e Input Power e Working Environment Physical e Material e Dimensions Weight Box Dimensions Boxed Weight Color Operating Temperature Storage Temperature Working Environment Ver 1 2 8 15 1 2 8 CMOS 2 0 Mega Pixel 30fps 1920 x 1080p 60fps 1280 x 720p 20X Optical Zoom 12X Digital Zoom f 4 7 94mm 5 tele to 58 wide 0 5 Lux at F1 6 2 years parts and labor 0 355 Up 90 Down 45 64 Presets 4 Patrol lines USB 3 0 Mini DIN 8 VISCA IN VISCA OUT RS485 Dip Switch Pin 7 TTL Signal 9600 bps DC 12V 2A 12V DC 2A 12V DC 10 5 14V DC 24W Max Indoor Aluminum Plastic 5 68 W x 5 63 H x 5 88 D 7 H w Tilt Up 144 2mm x 142 9mm x 149 4mm 177 8mmH w Tilt Up 2 52 lbs 1 14 kg 13 25 x 9 25 x 9 5 336 55mm x 234 95mm x 241 3mm 5 8 lbs 2 63 kg
12. r supply when required Caution Some compatible USB 3 0 extenders do not actually have the full 5Gbps bandwidth required for uncompressed HD video so check bandwidth specs Always connect the HuddleCam directly to the device in order to associate the UVC drivers before attempting to use any extension system USB 3 0 power saving settings in the device s operating system should be turned off completely for reliable USB 3 0 camera connectivity HuddleCam Cameras All HuddleCamHD cameras utilize the UVC USB Video Class drivers that are built into Windows Mac OS and Linux to stream HD video to your device via your device s USB port USB 2 0 or USB 3 0 depending upon HuddleCam model When your device successfully recognizes the camera your device will register the HuddleCam as an imaging device You can see this in your Windows Device Manager program type device manager into the Windows search tool as shown in the screenshot below Ver 1 2 8 15 uA HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 File Action View Help egi H mle 4 2 JoeM4700 p x Batteries p JE Computer b Disk drives b MS Display adapters b e DVD CD ROM drives gt ai Human Interface Devices gt fg TEEE 1394 Bus host controllers a J Imaging devices Fw Integrated Webcam ia i USB2 0 Camera p mm Keyboards b J Mice and other pointing devices b A Monitors aid EF Network adapters ER
13. ywood sandwiching the ceiling tile in between Do not over tighten NOTE The four raised areas of the ceiling bracket must face towards the ceiling Step 2 Step 3 Step 4 Slotted bolts Use the two slotted bolts to fix the camera bracket to the bottom of the camera body The 1 4 20 bolt is for the threaded insert in the camera body The smaller bolt threads into the bracket and pins the camera in place using the unthreaded opening on the camera body Camera Bracket Slide the camera bracket assembly on to the ceiling bracket allowing the 2 slotted bolt heads to fit over the large keyhole opening in the ceiling bracket Slide the camera and camera bracket until both bolt heads are fitted into the narrower slot of the large keyhole opening Use the locking screw to lock the ceiling and camera brackets together to finish the installation Ver 1 2 8 15 UT HuddleCamHD 152 Robbins Rd Downingtown PA 19335 USA HuddleCamHD com 1 800 486 5276 Troubleshooting9 eee ee eee ee eee re ere nre erre eere eee e e eese these eese eese sees ee eae Problem Cause Resolution There is no power to the Power adapter is Check the connections camera disconnected from mains between the camera or from camera power adapter and mains If anything is disconnected reconnect it Power switch is set to Set the power switch to OFF ON Camera will not connect USB cable is b
Download Pdf Manuals
Related Search