TK-8000 User Manual v.001 E
Contents
1. All information in this document is provided for reference only with no warranty of its suitability for any specific purpose This information has been thoroughly checked and is believed to be entirely reliable and consistent with the product that it describes However Fastwel accepts no responsibility for inaccuracies omissions or their consequences as well as liability arising from the use or application of any product or example described in this document Fastwel Co Ltd reserves the right to change modify and improve this document or the products described in it at Fastwel s discretion without further notice Software described in this document is provided on an as is basis without warranty Fastwel assumes no liability for consequential or incidental damages originated by the use of this software This document contains information which is property of Fastwel Co Ltd It is not allowed to reproduce it or transmit by any means to translate the document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co Ltd or one of its officially authorized agents Fastwel and Fastwel logo are trademarks owned by Fastwel Co Ltd Moscow Russian Federation Ethernet is a registered trademark of Xerox Corporation IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers Inc Intel is a trademark of Intel Corporation Pentium M and Celeron M are tradem2. 2 2 3 VGA CRT Interface and Connector Figure 2 4 Table 2 5 VGA Connector Pinout D Sub VGA CRT Connector The 15 contact female D Sub standard connector is used to connect a VGA CRT analog monitor to the TK 8000 This connector is located on the rear panel 1 Red Red video signal output Out 2 Green Green video signal output Out 3 Blue Blue video signal output Out 9 VCC_MON Power 5V 200 mA Out 12 DDC_DATA DC m data In Out 13 HSYNC Horizontal sync TTL out 14 VSYNC Vertical sync TTL out 15 DDC_CLOCK C clock Out 5 6 7 8 GND Signal ground 4 10 11 NC TK 8000 User Manual 24 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 2 3 Audio Interface The following standard audio connectors are located on the rear panel of TK 8000 Line Out Mic In and Line In 2 4 Serial Interfaces COM and COM RS 232 with limited functionality see below ports are available at the rear panel of TK 8000 as two 9 pin D Sub connectors and COM3 and COMA interfaces are available via the 9 pin D Sub connectors on the front panel All COM ports are compatible with the 16550 controller see the note below and include a complete set of handshaking and modem control signals maskable interrupt generation and data transfer of up to 460 8 Kb s Switching between RS 485 and TTL modes for COM3 and COMA ports is performed in BIOS Setup th
3. 12 1 4 2 Dimensions and Layout DiagramS rennen nennen nnn 13 1 5 Technical Specifications AA 15 1 5 1 Processor Memory and Chipset nennen nennen neret nnne 15 1 5 2 WTSI ACCS IT eege E E A 15 1 5 3 Monitoring and Lee tte 17 1 5 4 Ee tuc DEL Mu EE 17 1 5 5 SOMWAMNC e 18 2 Interfaces and Connectors uieeesieeseeeeeeese esie se enne nennt nnn tn asina nsnm asa tn Rasa sa sa annann nennen nanna 19 2 1 PC 104 and PC 104 Plus Interfaces A 19 2 2 Graphics Controller uie eee et ene pret pe ERRARE RR RD Ras Ex SER aane air RR aae R eire pes OC ASAE Ra 23 2 2 1 BA ORK nit e EE 23 2 2 2 Supported PHesohutons AA 24 2 2 3 VGA CRT Interface and Connector sesssesseesseeseretetetesitstrtttnettnntenetnttnttnnntnaenatenntnnstnnnnnennne 24 2 3 AUGIO INPSMaCE T 25 2 4 Serial Interfaces ELI benders Eee ere te Pe vide eH RE deed einen 25 2 5 USB hntertaces eee nette eiie eame x tuis a iem ei e tunsimer aida EE CS ae 26 2 6 Parallel Port Interface eeu ciere eec nene erae kenne un aA xcu E ARR RUNE Aa au pe CHER E RR Ku ind 27 20 GigabiL E te EE 27 2 8 EIDE Mite nt aCe tsi vss T EEE EP 28 2 9 SerialATA Interface ener rette treni pene E ai E Eiaa EE ee TEER Phen 30 2 10 CompactFlash Sockel aid p ge E ES ibt paren a Ea E taba EaR EO A osten aep ren 30 ERnMETU eom 32 2 12 Soft Power an
4. gt ACPI Control Sub Menu gt APM Control Sub Menu gt Workaround Control Sub Menu Fi TL F9 Esc e Enter F10 CPU power and thermal management MCH and ICH control options integrated graphics controller parameters as well as ACPI and APM control all these features are available via submenus on this screen 4 4 Security Menu Various system security settings such as supervisor password and other access control parameters are collected at this menu screen Main Advanced Intel Security Boot Custom Exit Item Specific Help mm Supervisor Password Is Clear User Password Is Clear Select FirstWare authentication level Set Supervisor Passuord Enter Set User Password Diskette access Fixed disk boot sector Normal Virus check reminder Disabled System backup reminder Disabled Password on boot F1 TL vs F9 Esc e Enter F10 TK 8000 User Manual 50 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel 4S TK 8000 4 5 Boot Menu Main Advanced Hard Drive CD ROM Drive Network Boot Intel Security E Enter Custom Exit Item Specific Help Keys used to vieu or configure devices lt Enter gt expands or collapses devices uith a or lt Ctrl Enter gt expands all lt Shift 1 gt enables or disables a device lt gt and lt gt moves the device up or down lt n gt May move removable device between Hard Disk or Removable Disk lt d gt Remove a device
5. 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 PCI 104 Connector PCI 104 connector is a 120 pin 30x4 2 mm pitch header located on the top of the processor module This interface header carries all of the appropriate 32 bit 33 MHz PCI signals Figure 2 2 PCI 104 J4 Connector Contacts Layout e Hrn ommum omm A dumm lt nnm Si x amp Table 2 3 PCI 104 J4 Connector Contacts Designation 1 GND 5 0V KEY2 Reserved 5 ADOO 2 VI O ADO02 ADO1 5V 3 AD05 GND ADO04 ADOS 4 C BEO AD07 GND ADO6 5 GND ADO9 ADO08 GND 6 AD11 VI O AD10 M66EN 7 AD14 AD13 GND AD12 8 3 3V C BE1 AD15 3 3V 9 SERR GND Reserved PAR 10 GND PERR 3 3V Reserved 11 STOP 3 3V LOCK GND 12 3 3V TRDY GND DEVSEL 13 FRAME GND IRDY 3 3V 14 GND AD16 3 3V C BE2 15 AD18 3 3V AD17 GND 16 AD21 AD20 GND AD19 17 3 3V AD23 AD22 3 3V 18 IDSELO GND IDSEL1 IDSEL2 19 AD24 C BE3 VI O IDSEL3 20 GND AD26 AD25 GND 21 AD29 5V AD28 AD27 22 5V AD30 GND AD31 23 REQO GND REQ1 VI O 24 GND REQ2 5V GNTO 25 GNT1 VI O GNT2 GND 26 5V CLKO GND CLK1 27 CLK2 5V CLK3 GND 28 GND INTD 5V RST 29 12V INTA INTB INTC 30 12V Reserved Reserv
6. Selecting Exit from menu bar on the Main Menu or pressing lt Esc gt at any Main Menu screen displays the following menu Main Advanced Intel Secur ity Boot Custom Exit Item Specific Help Exit Discarding Changes Load Setup Defaults Exit System Setup and Discard Changes save your changes to Save Changes CMOS F1 TL R F9 Esc e Enter F10 Note that Esc does not exit this menu You must select one of the items from the menu to exit Here you can select whether or not to save changes made to BIOS parameters during the current session to CMOS memory and exit BIOS Setup utility TK 8000 User Manual 54 2009 Fastwel v 001 E
7. that is not installed F9 F10 After you turn on your computer it will attempt to load the operating system from the chosen device If it cannot find the operating system on that device it will attempt to load it from one or more other devices in the order specified in the Boot Menu Boot devices i e with access to an operating system can include hard drives floppy drives CD ROMs removable devices e g lomega Zip drives and network cards Use the keys described in Item Specific Help to arrange devices in order to specify the priority of the devices from which the BIOS will attempt to boot the operating system TK 8000 User Manual 51 2009 Fastwe v 001 E Phoenix BIOS Setup Fastwel Ley TK 8000 4 5 1 Boot Details 4 5 1 1 Booting without a Monitor Keyboard or Mouse To boot without a monitor keyboard or mouse set the item POST Errors to Disabled at the page Main Menu in PhoenixBIOS Setup program This setting is a default one Note A If the computer was booted without a connected monitor the display will be empty even if a monitor is connected later during operation To get the correct display output it is necessary to reboot the computer with a connected monitor This is a Intel VideoBIOS particularity 4 5 1 2 Booting from USB To boot from a device connected to USB igi Connect the device to boot from to a USB port The appropriate USB controller should be enabled m Enter the P
8. IDE Channel 2 Master None gt IDE Channel 3 Master None System Menory 640 KB Extended Hemory 1038336 KB POST Errors Disabled F1 1 B F9 Esc e Enter F10 The following subsections explain the purpose of main functional areas of the screen and give description of the fields TK 8000 User Manual 46 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel 4S TK 8000 Menu Bar The Menu Bar at the top of the window lists these selections Main Basic system configuration Advanced Use to set the Advanced Features available on your system s chipset Intel Intel chipset specific parameters Security Configuration of system security settings Boot Boot sequence configuration Custom Configuration of special board features Exit Exits the Setup utility Use the left and right arrow keys to make a selection For a description on exiting the Main Menu see Exit Menu section below Legend Bar The legend bar at the bottom of the screen lists the keys to navigate within menu system to make your selections or exit the current menu The following table describes the legend keys and their alternates F1 or Alt H General Help window See below Esc Exit this menu lt or arrow keys Select a different menu 1 or arrow keys Move cursor up and down Tab or lt Shift Tab gt Cycle cursor between the fields Home
9. LPT SBR Processors Sound video and game controllers d System devices Universal Serial Bus controllers 4 In the opened wizard s window check Yes this time only and press Next 5 In the next window check Install from a list or specific location and press Next 6 In the next window check Don t search will choose the driver to install and press Next 7 Press Have disk button locate and select the driver win2k_xp ite8888 and press OK 8 To start the installation press Next 9 To complete the installation press Finish 3 3 2 Linux 2 4 Ethernet Driver Installation To uncompress the files to get the files out of a tarball use the following command in Linux tar xvfz e1000 7 2 9 tar gz Graphics Driver Installation To uncompress the files to get the files out of a tarball use the following command tar xvfz Intel 3 4 3006 20051209 1386 tar gz TK 8000 User Manual 41 2009 Fastwel v 001 E Installation and Setup Fastwel Lee TK 8000 3 4 Watchdog Timer The watchdog timer eliminates system hang ups both during the start up process for example in case of mistakes in BIOS when the additional timer is not able to restart the system and during normal operation The timeout period is set in BIOS Setup program On the expiry of the timeout period the watchdog timer issues Reset signal During start up process watch
10. Primary interrupt select TK 8000 User Manual 45 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Ley TK 8000 4 Phoenix BIOS Setup The Phoenix BIOS in your computer is a customized version of a standard BIOS for IBM PC AT compatible personal computers equipped with Intel x86 and compatible processors The BIOS provides low level support for the system central processing memory and I O subsystems With the help of BIOS Setup program you can modify BIOS configuration parameters and control special features of your computer The Setup program offers a convenient menu interface to modify basic system configuration settings and to switch between the subsystems operation modes These settings are then stored in a dedicated battery backed memory CMOS RAM that retains the information when the system power is switched off To start the Phoenix BIOS Setup utility turn on or reboot your system PhoenixBIOS displays this message Press lt F2 gt to enter SETUP Pressing lt F2 gt lets you enter the Setup utility The first screen is the Main Menu 4 1 Main Menu The Main Menu screen is shown below Advanced Intel Security Boot Custom Exit Item Specific Help 9 00 26 System Date 09 20 2006 lt Tab gt lt Shift Tab gt or lt Enter gt selects field gt IDE Channel 0 Master None gt IDE Channel 0 Slave None gt IDE Channel 1 Master None gt IDE Channel 1 Slave None
11. a PCI X interface that maximizes the use of bursts for efficient bus usage The interfaces provide automatic detection and switching between 10Base T 100Base TX and 1000Base T operation modes Each of the two Ethernet channels may be disabled via the BIOS Setup or user software utility to release system resources TK 8000 User Manual 27 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 Table 2 11 Gigabit Ethernet Connectors Pinouts 1 O TX O TX UO BI DA 2 O TX O TX UO BI DA 3 l RX l RX UO BI DB 4 2 e O BI DC 5 UO BI DC 6 l RX l RX UO BI DB 7 UO BI_DD 8 UO BI DD MDI Standard Ethernet Cable Integrated Ethernet LEDs Optional Green Line This LED indicates network connection The LED lights up when the line is connected Green Act this LED monitors network activity The LED lights up when network packets are sent or received through the RJ45 port When this LED is not lit it means that the computer is not sending or receiving network data 2 8 EIDE Interface The EIDE interface supports several operation modes PIO mode 8237 type DMA mode Ultra DMA 33 modes In PIO mode the central processor controls the data transfers In all the DMA modes the CPU is not engaged in data transfer DMA modes are similar to each other but differ in data transfer protocols details and DMA clock frequency thus
12. or End Move cursor to top or bottom of window lt PgUp gt or lt PgDn gt Move cursor to next or previous page lt F5 gt or lt gt Select the next lower value for the field lt F6 gt or lt gt or lt Space gt Select the next higher value for the field lt F9 gt Load the Default Configuration values for the complete BIOS lt F10 gt Save and exit lt Enter gt Execute command or select Submenu lt Alt R gt Refresh screen To select an item use the arrow keys to move the cursor to the field you want Then use the plus and minus value keys to select a value for that field The Save Values command in the Exit Menu save the values currently displayed in all the menus A pointer gt marks all submenus To display a submenu use the arrow keys to move the cursor to the submenu you want and then press Enter TK 8000 User Manual 47 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Le TK 8000 Item Specific Help Window The help window on the right side of each menu screen displays the field specific help text it updates as you move the cursor from field to field General Help Window Pressing lt F1 gt or lt Alt H gt on any menu brings up the General Help window that describes the legend keys and their alternates Advanced Intel Security Boot Custom General Help Setup changes system behavior by modifying the BIOS configuration Selecting inc
13. screws Connect data and power cables to the disk drive Fasten the disk drive unit on the chassis with four screws Fasten the bottom lid and the CF cover with the eight screws oa e w Fasten the front panel and the rear panel 3 2 6 Wall Mount Kit Installation Get the brackets ready and fasten each bracket with screws on the bottom lid 3 3 Drivers Installation The TK 8000 comes with a CD ROM that contains necessary drivers and utilities Table 3 1 Drivers Location Windows XP Audio Driver win2k_xp audio Chipset Driver win2k_xp chipset Ethernet Driver win2k_xp eth Video Driver win2k_xp graphics ISA Bridge Driver win2k_xp ite8888 Linux 2 4 Ethernet Driver linux eth DRI Video Driver linux graphics fully compatible with Windows XP Professional SP3 Insert the TK 8000 CD ROM into the CD ROM drive The Autorun program will run automatically Choose the drivers to install following instructions below TK 8000 User Manual 39 2009 Fastwel v 001 E Installation and Setup Fastwel LE TK 8000 3 3 1 Windows XP Audio Driver Installation o ON Oar ob Computer Management el Computer Management Local E i System Tools Ir gal Event Viewer ze Kl Shared Folders z Local Users and Groups Zi Performance Logs and Alert E Device Manager Ki Storage Removable Storage j Disk Defragmenter Disk Management D E3 Services and Applicat
14. the manufacturer as soon as possible Retain the damaged packing material for inspection After unpacking the product you should inspect it for visible damage that could have occurred during shipping or unpacking If damage is observed usually in the form of bent component leads or loose socketed components contact Fastwel s official distributor from which you have purchased the product for additional instructions Depending on the severity of the damage the product may even need to be returned to the factory for repair DO NOT apply power to the product if it has visible damage Doing so may cause further possibly irreparable damage as well as result in a fire or electric shock hazard If the product contains socketed components they should be inspected to make sure they are seated fully in their sockets TK 8000 User Manual 6 2009 Fastwel v 001 E Fastwel TES TK 8000 Handling In performing all necessary installation and application operations please follow only the instructions supplied by the present manual In order to keep Fastwel s warranty you must not change or modify this product in any way other than specifically approved by Fastwel or described in this manual Technical characteristics of the systems in which this product is installed such as operating temperature ranges and power supply parameters should conform to the requirements stated by this document Retain all the original packaging you will need
15. value from control register MOV DX 302H MOV AL FOH OUT DX AL MOV DX 303H IN AL DX AL contains control register value TK 8000 User Manual 33 2009 Fastwel v 001 E Interfaces and Connectors Fastwel Ty TK 8000 Moreover red D7 LED is lit when a BIOS error is detected and Reset signal is generated 2 13 2 Now LED can be switched on OR AL 8 set bit 3 OUT DX AL or switched off AND AL 247 Clear bit 3 OUT DX AL To leave configuration mode MOV DX 302H MOV AL 57H OUT DX AL MOV AL 46H OUT DX AL D7 Green and D8 Green LEDs Control D7 and D8 indicators are controlled via Super I O LPC47M10X controller registers programming For control purposes GP142 line is programmed as output Setting logical 1 at it lights up the LED setting logical 0 switches it off TK 8000 User Manual 34 2009 Fastwel v 001 E Installation and Setup Fastwel Lee TK 8000 3 Installation and Setup TK 8000 is easy to install However it is necessary to follow the procedures and safety regulations below to install hardware and software correctly without damage to the equipment or harm to personnel For details on installation of an operating system please refer to the relevant software documentation 3 1 Safety Regulations The following safety regulations must be observed when installing or operating the TK 8000 Fastwel assumes no responsibility for any damage resulting fro
16. 1 Matin Me rt EE EC 46 A Advanced In EE HM i ees 49 4 3 Mitel Me TnT P E E E E LR EES 50 4 4 Security Men 50 4 5 Elle i EI eee ET 51 4 5 1 leie ET 52 4 5 1 1 Booting without a Monitor Keyboard or Mouse AA 52 45 12 Bo otingfrom USB EE 52 SR Melon DEEE E ett T T E bui 53 4 7 Exit EE 54 List of Tables Table 2 1 PC 104 J11 Rows A and B Connector Contacts Desionaton 20 Table 2 2 PC 104 J11 Rows C and D Connector Contacts Desionaton 21 Table 2 3 PCI 104 J4 Connector Contacts Designation sseeeeeeneneenennneen nennen nene 22 Table 2 4 Supported Display Modes prr eter ee tirer rer deed ree ve rahe Edge Ce 24 Table 2 5 VGA Gonneclor Pinout iiM DII DE DEM ONE IE MEME 24 Table 2 6 Functions of the Serial Port Interfaces sse nennen neret 25 Table 2 7 Serial Port Connectors COM1 and COM Pinouts nennen 26 Table 2 8 Serial Port Connectors COM3 and COM4 Pinouts nennen 26 Table 2 9 USB Connectors PiroUt 3 oerte i o dened Eg ee a a i iai 26 Table 2 10 D Sub LPT Gornnector PInoUt iiio te m c iret eese e Peres epe vede edere Eed 27 Table 2 11 Gigabit Ethernet Connectors Pinouts neret nenn nre 28 Table 2 12 Standard EIDE HDD Connector J9 Pinout nennen rennen 29 Table 2 13 SATA Connectors J7 J8 Pinout eee eeeeeceneeeeeee cece eeeeeteaeeeeaeeseaeesaeeseaeeeaeeseaeessaeeseaeeenaeessaeeeaes 30 Table 2 14 CompactFlash Socket J23 Pinout c ceecceeeceeeeeeeeneee
17. 3 V 3 3 V power 37 INTRQ Interrupt In 38 3 3V 3 3 V power 39 CSEL Master Slave Out 40 VS2 41 Reset Reset Out 42 IORDY I O ready In 43 INPACK DMA Request Out 44 REG DMA Acknowledge 45 ACTIVE IDE Activity 46 PDIAG DMA Mode Detect 47 D08 Data 08 In Out 48 D09 Data 09 In Out 49 D10 Data 10 In Out 50 GND TK 8000 User Manual 2009 Fastwel v 001 E 31 Interfaces and Connectors Fastwel TES TK 8000 2 11 Power Supply Figure 2 12 External Power Supply Connector DC power is supplied to TK 8000 via the Phoenix connector on the front panel The mating connector is included in the supplied set Ope O DC input voltage is 9 to 30 V DC IN V V FG Optional external AC DC power adapter 1757912001 is available with AC input voltage of 100 240 V and output voltage of 19 VDC Power cable 1702031831 is ordered separately The table below presents designation of the power connector contacts Table 2 15 Power Supply Connector Pinout V 9 30 VDC V 0 FG GND it is not required for operation System power on off switch PWR is located on the front panel as well 2 12 Soft Power and Reset Connectors 2 pin connectors SoftPower J28 and Reset J29 are located on the top side of the processor module These connectors can be used at the factory for debugging purposes only They are not connected to any external connectors at the current ver
18. A13 Out B18 DRQ1 In A19 SA12 Out B19 REFRESH Out A20 SA11 Out B20 SYSCLK Out A21 SA10 Out B21 IRQ7 In A22 SA9 Out B22 IRQ6 In A23 SA8 Out B23 IRQ5 In A24 SA7 Out B24 IRQ4 In A25 SA6 Out B25 IRQ3 In A26 SA5 Out B26 DACK2 Out A27 SA4 Out B27 TC Out A28 SA3 Out B28 BALE Out A29 SA2 Out B29 5V Power A30 SA1 Out B30 OSC Out A31 SAO Out B31 GND Ground A32 GND Ground B32 GND Ground TK 8000 User Manual 2009 Fastwel v 001 E 20 Interfaces and Connectors Fastwel 4S TK 8000 Table 2 2 PC 104 J11 Rows C and D Connector Contacts Designation In the tables above wow Not used CO GND Ground DO GND Ground C1 SBHE Out D1 MEMCS16 In C2 LA23 Out D2 IOCS16 In C3 LA22 Out D3 IRQ10 In C4 LA21 Out D4 IRQ11 In C5 LA20 Out D5 IRQ12 In C6 LA19 Out D6 IRQ13 In C7 LA18 Out D7 IRQ14 In C8 LA17 Out D8 DACKO Out C9 MEMR Out D9 DRQO In C10 MEMW Out D10 DACK5 Out C11 SD8 In Out D11 DRQ5 In C12 SD9 In Out D12 DACK6 Out C13 SD10 In Out D13 DRQ6 In C14 SD11 In Out D14 DACK7 Out C15 SD12 In Out D15 DRQ7 In C16 SD13 In Out D16 5V Power C17 SD14 In Out D17 MASTER In C18 SD15 In Out D18 GND Ground C19 KEY D19 GND Ground Note Power The power is supplied to the module installed in a stack In Out column shows the data transfer direction for a processor module being the bus master TK 8000 User Manual 21
19. Fastwel Le TK 8000 Intel Pentium M Based Fanless Embedded Controller with IP52 Protection User Manual Rev 002 E September 2014 The product described in this manual is compliant to all related CE standards Product Title TK 8000 Document name TK 8000 User Manual Manual version 002 E Ref doc ver CPC800 02 004 R 002a E AEC7450 Manual 1st Ed Copyright 2014 Fastwel Co Ltd All rights reserved Revision History 001 Initial version TK 8000 November 2009 Contact Information Fastwel Co Ltd Fastwel Corporation US Address 108 Profsoyuznaya st 45 Main Street Suite 319 Moscow 117487 Brooklyn New York 11201 Russian Federation USA Tel 7 495 232 1681 1 718 554 3686 Fax 7 495 232 1654 1 718 797 0600 Toll free 1 877 787 8443 1 877 RURUGGED E mail info fastwel com Web http www fastwel com Fastwel TES TK 8000 Table of Contents Table GO COntents NEEDLE Eme 1 lstor Tables E 2 LiStor e E E E E T Ee eee 3 Notation eene EE A General Safety Precautions eu eE einige ARR ee Nees 5 Unpacking Inspection and Handling 6 Three Year Warr Mty EET 7 1 MEO GU Le E 8 1 1 OVeIVIBW octets E E tL cime teu EE 8 L EE TIK B000 V ersiOnsiectxigiitee RSA ie A Ale ee ee 10 DEO D Zee dim Em 11 EU CUMPIED CUI REREREPRPHLT 11 1 4 1 Module Appearance
20. GME DVMT graphics core Intelligent Memory Management Integrated 350 MHz DAC 2 2 1 DVM Technology The 855GME chipset supports the Dynamic Video Memory Technology DVMT This technology provides use of all available memory in the most efficient way for maximum graphics performance DVMT dynamically responds to requests from applications allocating the required amount of video memory The Intel amp 855GME graphics driver is allowed to request up to 96 MB of system memory When not needed by the graphics subsystem the memory is freed up for other applications Thus memory usage is balanced for optimal graphics and system memory performance To support legacy VGA devices the internal video controller needs at least 1 MB of system memory Thus the reported system memory size is always 1 MB less than available amount of physical memory TK 8000 User Manual 23 2009 Fastwel v 001 E Interfaces and Connectors Fastwel Lp TK 8000 2 2 2 Supported Resolutions The integrated 350 MHz RAMDAC of the 855GME chipset allows direct connection of a progressive scan analog monitor with a resolution of up to 2048 x 1536 at 75 Hz The supported resolution depends on the color depth and on the vertical scanning frequency as illustrated in the table below Table 2 4 Supported Display Modes 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536
21. L2 cache 1 GB DDR SDRAM with ECC and embedded Graphics Engine with VGA output up to 2048x1536 75 Hz Fastwel TK 8000 is capable to perform major computing and visualization tasks in industrial applications within extended temperature range from 40 C to 70 C Modern board architecture and robust mechanical design ensure capability of Fastwel TK 8000 to withstand up to 50G shock up to 5G vibration and up to 9596 humidity level without operability loss All electronic components including CPU SDRAM memory and 32 MB flash memory are soldered on board TK 8000 is equipped with conduction cooling system for effective heat sinking from CPU and other critical components to the all metal chassis Two Gigabit Ethernet channels provide Fastwel TK 8000 with high speed communication links important for fast data exchange with server or storage facility for working in Remote Desktops operation mode or any other bandwidth hungry applications Two RS232 ports two RS485 ports four USB 2 0 ports and one multi mode parallel port provide connectivity to peripheral devices Audio interface is available via three audio jacks The system can be expanded using one PC 104 or PC 104 Plus module installed on the processor module inside the system chassis however this may require the front panel design changes Fastwel TK 8000 can be ordered with CF or SSD installed having either IDE or SATA interfaces BIOS of Fastwel TK 8000 can be configured for booting from on
22. Pro XPE Windows XP Embedded LNX Linux 2 4 20 2 6 11 WCE Windows CE QNX QNX 6 0 4 25 External power supply ACDC External AC DC power supply unit TK 8000 02 P1 8 RAM1024 CF2G HDD120 XPE BoxPC Pentium M DDR FFD 32 MB SVGA LVDS 2x Gigabit Ethernet Pentium M 1 8 GHz 400 MHz FSB 1024 MB soldered DDR SDRAM 2 GB CompactFlash card Hard disk drive 2 5 120 GB Windows XP Embedded TK 8000 User Manual 10 2009 Fastwel v 001 E Introduction Fastwel Lee TK 8000 1 3 Delivery Checklist Before you begin operating your PC please make sure that the following materials are enclosed 1 4 1 ONOarwh TK 8000 embedded controller One Phoenix power connector Two wallmount brackets Adaptor for mounting a HDD SSD Screw package CD ROM with documentation and service software Protective caps set for all front and rear panel connectors installed on TK 8000 Consumer package Note Keep the original package at least until the warranty period is over It can be used for future storage or warranty shipments System Diagrams The diagrams in this section give visual information about the TK 8000 system design its appearance and connectors The diagrams may not reflect insignificant differences between the revisions of TK 8000 ww TK 8000 User Manual 11 2009 Fastwel v 001 E Introduction Fastwel TEN TK 8000 1 4 1 Module Appearance Figure 1 1 TK 8000 Appearance
23. Rear and Front Views The appearance may vary for different versions of the system due to continuous improvement and development efforts TK 8000 User Manual 12 2009 Fastwel v 001 E Introduction Fastwel 4S TK 8000 1 4 2 Dimensions and Layout Diagrams Figure 1 2 TK 8000 Top View Dimensions I I 8 S S o Kal i E e 28 8 o o SI A e d S S Y os 4 50 Y Y 212 00 222 00 238 00 Gi TK 8000 User Manual 13 2009 Fastwel v 001 E Introduction Fastwel XE TK 8000 Figure 1 3 TK 8000 Front Panel Dimensions and Layout 64 38 82 38 00000 The layout may slightly vary for different versions of
24. a 2 In Out 14 DD13 HD data 13 In Out 15 DD1 HD data 1 In Out 16 DD14 HD data 14 In Out 17 DDO HD data 0 In Out 18 DD15 HD data 15 In Out 19 GND Ground signal 20 21 DRQ DMA request In 22 GND Ground signal 23 AOW I O write Out 24 GND Ground signal 25 NOR I O read Out 26 GND Ground signal 27 IlOCHRDY I O channel ready In 28 GND Ground signal 29 DACK DMA Ack Out 30 GND Ground signal 31 IRQ Interrupt request In 32 CS16 33 DA1 Address 1 Out 34 ATA66 100 Detect 35 DAO Address 0 Out 36 DA2 Address 2 Out 37 CS1 Select Register 1 Out 38 CS3 Select Register 3 Out 39 DASP IDE Activity Out 40 GND Ground signal 41 45V 5V 42 5V 5V 43 GND Ground signal 44 TK 8000 User Manual 29 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 2 9 SerialATA Interface Figure 2 10 SATA Connector The processor module of TK 8000 bears two on board SATA connectors J7 J8 for attachment of SerialATA HDDs or SSDs with the exchange rate of up to 150 MB s The connectors pinout is presented in the table below Table 2 13 SATA Connectors J7 J8 Pinout 1 GND TXP TXN GND RXN RXP GND o Oo BR Ww Pp 2 10 CompactFlash Socket CompactFlash card is a compact removable mass storage device It provides full IDE functionality compatible with the 16 bit ATA ATAPI 4 interface TK 8000 has an internal Compa
25. arks of Intel Corporation Microsoft is a trademark of the Microsoft corporation PC 104 and the PC 104 logo are trademarks of the PC 104 Consortium In addition this document may include names company logos and trademarks which are registered trademarks and therefore are property of their respective owners Fastwel welcomes suggestions remarks and proposals regarding the form and the content of this Manual TK 8000 User Manual 3 2009 Fastwel v 001 E Fastwel Ley TK 8000 Notation Conventions Warning ESD Sensitive Device This symbol draws your attention to the information related to electro static sensitivity of your product and its components To keep product safety and operability it is necessary to handle it with care and follow the ESD safety directions Warning This sign marks warnings about hot surfaces The surface of the heatsink and some components can get very hot during operation Take due care when handling avoid touching hot surfaces Caution Electric Shock This symbol warns about danger of electrical shock gt 60 V when touching products or parts of them Failure to observe the indicated precautions and directions may expose your life to danger and may lead to damage to your product Warning Information marked by this symbol is essential for human and equipment safety Read this information attentively be watchful Note This symbol and title marks important information to be read
26. attentively for your own benefit 2 gt gt ES TK 8000 User Manual 4 2009 Fastwel v 001 E Fastwel TES TK 8000 General Safety Precautions This product was developed for fault free operation Its design provides conformance to all related safety requirements However the life of this product can be seriously shortened by improper handling and incorrect operation That is why it is necessary to follow general safety and operational instructions below A A AK Warning Only sufficiently skilled personnel must handle this product Warning When handling this product special care must be taken not to hit the heatsink if installed against another rigid object Also be careful not to drop the product since this may cause damage to sensitive components Please keep in mind that any physical damage to this product is not covered under warranty Note This product is guaranteed to operate within the published temperature ranges and relevant conditions However prolonged operation near the maximum temperature is not recommended by Fastwel or by electronic chip manufacturers due to thermal stress related failure mechanisms These mechanisms are common to all silicon devices they can reduce the MTBF of the product by increasing the failure probability Prolonged operation at the lower limits of the temperature ranges has no limitations Caution Electric Shock Before installing this product into a system a
27. ause short circuit and result in damage to the battery and other components a Store this product in its protective packaging while it is not used for operational purposes Unpacking The product is carefully packed in a carton box to protect it against possible damage and harmful influence during shipping Unpack the product indoors only at a temperature not less than 15 C and relative humidity not more than 70 Please note that if the product was exposed to the temperatures below 0 C for a long time it is necessary to keep it at normal conditions for at least 24 hours before unpacking Do not keep the product close to a heat source Following ESD precautions carefully take the product out of the shipping carton box Proper handling of the product is critical to ensure correct operation and long term reliability When unpacking the product and whenever handling it thereafter be sure to hold electronic modules preferably by the front panel card edges or ejector handles Avoid touching the components and connectors Retain all original packaging at least until the warranty period is over You may need it for shipments or for storage of the product Initial Inspection Although the product is carefully packaged it is still possible that shipping damages may occur Careful inspection of the shipping carton can reveal evidence of damage or rough handling Should you notice that the package is damaged please notify the shipping service and
28. board flash CF storage or via LAN and USB TK 8000 supports wide range of real time QNX WinCE and non real time Windows XP XP Embedded and Linux operating systems Fastwel TK 8000 requires external 9 30V DC power supply TK 8000 User Manual 8 2009 Fastwel v 001 E Introduction Fastwel Lee TK 8000 Some of the TK 8000 features are gl Durable wallmount aluminum alloy housing with IP52 protection E Wide operating temperature range H Fanless design with Intel Pentium M 1 8 GHz processor Up to 2 MB L2 on die cache running at CPU speed 400 MHz processor system bus 82855GME GMCH and 6300ESB Hance Rapid ICH chipset 1 GB of soldered PC2700 DDR SDRAM memory with ECC PC 104 or PC 104 Plus expansion capability Integrated high performance VGA controller 7 2D 3D accelerator Video memory up to 64 MB shared with system 7 Analog display support with resolutions of up to 2048x1536 pixels at 16 bits and 75 Hz Two Gigabit Ethernet interfaces via PCI X bus 10Base T 100Base TX and 1000Base T Space for one EIDE or SerialATA 2 5 disk drive inside the housing Internal CompactFlash Type I II socket true IDE mode Four serial ports on the front and rear panels High speed NS16C550 compatible COM1 and COM2 RS 232 rear panel e COM and COM4 RS 485 front panel Four USB 2 0 ports Audio AC97 codec LM4550 Line In stereo Line Out stereo Microphone input Parallel port SPP ECP EPP compatible Ha
29. ctFlash Type UI 50 pin socket J23 on the bottom side of the processor module It is accessible from the outside of the system chassis via an opening closed with separate cover Figure 2 11 CompactFlash Slot Cover TK 8000 User Manual 30 2009 Fastwel v 001 E Fastwel 4S8 Interfaces and Connectors TK 8000 CompactFlash socket is connected to the primary master EIDE channel Table 2 14 CompactFlash Socket J23 Pinout 1 GND Ground signal 2 D03 Data 3 In Out 3 D04 Data 4 In Out 4 D05 Data 5 In Out 5 D06 Data 6 In Out 6 D07 Data 7 In Out 7 IDE_CSO Chip select 0 Out 8 GND 9 GND 10 GND 11 GND 12 GND 13 3 3V 3 3 V power 14 GND 15 GND 16 GND 17 GND 18 A02 Address 2 Out 19 A01 Address 1 Out 20 A00 Address 0 Out 21 DOO Data 0 In Out 22 D01 Data 1 In Out 23 D02 Data 2 In Out 24 lOCS16 25 CD2 26 CD1 27 D11 Data 11 In Out 28 D12 Data 12 In Out 29 D13 Data 13 In Out 30 D14 Data 14 In Out 31 D15 Data 15 In Out 32 IDE CS1 Chip select 1 Out 33 VS1 34 IORD UO read Out 35 IOWR UO write Out 36 3
30. d Menu screen is shown below Advanced Intel Security Boot Custom Exit Item Specific Help UE Reset Configuration Data No Large Disk ficcess Mode DOS Select the operating Local Bus IDE adapter Both system installed on your system which Parallel ATA Both you will use most Serial ATA Enabled commonly Native Mode Operation Auto Note An incorrect gt Advanced Chipset Control setting can cause gt Super I 0 Device Configuration some operat ing gt Keyboard Features systems to display gt Cache Memory unexpected behavior gt PCI PNP ISA IRQ Resource Exclusion Legacy USB Support Enable menory gap Disabled v EA Esc e Enter F10 This menu screen gives access to advanced system configuration parameters Submenus allow setting thermal and power control options configuring serial and parallel ports adjusting keyboard behavior enabling cache memory use for various system components and reserving IRQs for legacy ISA devices Remember that incorrect settings can cause your system to malfunction TK 8000 User Manual 49 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Le TK 8000 4 3 Intel Menu The Intel menu screen offers a number of submenus containing chipset specific control fields Main Advanced Intel Security Boot Custom Exit Item Specific Help gt MCH Control Sub Menu gt Video Intel IGD Control Sub Menu These items control gt ICH Control Sub Menu various CPU parameters
31. d Reset CGonnectors nne enn 32 219 RR le e e TEE 33 2 13 1 D7 R d LED gtt EE 33 2 13 2 D7 Green and D8 Green LEDs Control 34 3 INStallatiOn Edu 35 3 1 Este 35 3 2 ele saine TE 36 3 2 1 USB Devices Connection 36 3 2 2 CompactFlash Cards Installation A 37 3 2 3 Battery Replacement cccccccesecceeceseeeeeeseeeeseseeceeesaeeeeeseneaeeeseeseseeseeeeseseaeesanenaeeseeeeenseseeaeeess 37 3 2 4 PC 104 and PC 104 Plus Expansion Module Installation eene 38 3 2 4 1 PC 104 Plus Voltage Selection nennen 38 3 2 5 HDD or SSD Installation E U U H 39 TK 8000 User Manual 1 2009 Fastwel v 001 E Fastwel XE TK 8000 3 2 6 Wall Mount Kit Installation ssssseesssesssssesseeseeeeeeeenenneeenenen nennen erret nn nnnnrnr nennt nnn 39 3 3 Drivers Installation asrine ane aa a e ae eE EE Ea E EEE EEE ea eia ERLEA 39 3 3 1 Melo PEPERIT 40 3 3 2 Blat 41 3 4 Watchdog Timer 3 4 1 Access to Watchdog Registers AAA 42 3 4 2 Configuration Mode et 42 3 4 3 Watchdog Timer Programming E aap i ae 43 3 4 4 Global Configuration Registers AA 44 3 4 5 Logical Devices Configuration Registers cccceesceceeeeeeeeceneeseeeeteaeeeeaeeseaeeeeaeeseaeeeeaeeseaeeeaaes 44 3 4 6 Watchdog Timer Registers Logical Device 1 45 4 Phoenix BIOS Setup mee 46 4
32. dog timer monitors BIOS code execution If BIOS error is detected the system is automatically reset and red D7 LED is lit indicating system failure state The instructions on watchdog timer programming can be found in the following subsections FPGA XILINX XC3S200 is used to control the watchdog timer 17 lower bits of the 24 bit WD FPGA register are used to program the watchdog timeout period It is possible to set the timeout period from 0 to 512 seconds with increments of 30 52 us by changing the value in this register By default without prior initialization the watchdog timeout period is set to maximum that is 512 seconds The equation below can be used to calculate the timeout Twp in us as a function of the decimal value in the WD register Kwp Two us Kwp 10 2 For example decimal value 1 of Kwn 000001h corresponds to the timeout of 30 52 us and Kwp 16777215 FFFFFFh 512 seconds 3 4 1 Access to Watchdog Registers The unit s configuration is based on Plug and Play architecture Watchdog timer registers are available via standard I O registers Index and Data ports in configuration mode Config Port 302h Write Index Port 302h Read Write Data Port 303h Read Write 3 4 2 Configuration Mode Configuration mode is enabled by writing lt 46h gt lt 57h gt to Config Port Configuration mode is disabled by writing lt 57h gt lt 46h gt to Config Port Index and Data ports are available in conf
33. e default setting is RS 485 Table 2 6 Functions of the Serial Port Interfaces COM1 Rear panel RS232 COM2 Rear panel RS232 COMS Front panel RS485 COM4 Front panel RS485 TTL signals are not connected to the contacts of front panel connectors for the current version of the computer Figure 2 5 D Sub Serial Connectors 1 5 According to Intel 6300ESB I O Controller HUB ICH Specification o Zr fo update it has limited functionality due to unexpected behavior of E a serial port interrupt enable register 9 6 Below is an abstract from this document 2 Behavior of Serial Port Interrupt Enable Register Problem The Serial Port Interrupt Enable Register IER bit 1 3f9h Transmit Data request Interrupt Enable will not change status if the bit has been set previously Implication Will not cause an interrupt if the register bit has been set already This hinders the serial ports from being fully 100 percent 16550 compatible Workaround Customers may be able to implement a BIOS workaround to clear out the bit IER bit 1 to 0 before programing the bit to 1 Status No fix Thus serial ports integrated in South bridge are compatible with standard UART 16550 except the following registers 1 Changed designation of bits 4 and 5 of IER Interrupt Enable Register 2 Changed designation of bits 6 and 7 of FCR FIFO Control Register For details see IntelR 6300ESB I O Contr
34. ed GND 3 3V_KEY TK 8000 User Manual 22 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 The PC 104 Plus VIO selector J3 is located on the top side of the processor module next to the PCI 104 header and allows to set the voltage supplied to PCI interface I O buffers It is a standard 3 pin 2 54 pitch header Figure below presents explanation of its jumper positions Figure 2 3 PC 104 Plus VIO Selector J3 Positions The jumper should be removed only if the module is powered via m J4 connector from a PC 104 Plus power supply module In case the processor module receives power through J1 power connector the jumper must be installed in one of the two positions described below E o Contacts 1 2 closed 5 V power is supplied to PCI interface I O buffers o Contacts 2 3 closed 3 3 V is supplied Is oak N ol 2 2 Graphics Controller The 855GME chipset of the processor module includes a highly integrated graphics accelerator delivering high performance 2D and 3D video capabilities The graphics controller provides interface to a standard analog monitor via the VGA connector on TK 8000 rear panel Integrated 2D 3D graphics features Resolutions up to 1600x1200 at 100 Hz 1920x1440 at 85 Hz and 2048x1536 at 75 Hz 3D Setup and Render Engine 3D Graphics Rasterization Enhancements High Quality Texture Engine Full 2D hardware acceleration Intel 855GM 855
35. eeeeteaeeeeaeeseaeeseaeeseaeeseaeeseaeeseaeeseaeeenaeessaeeeaes 31 Table 2 15 Power Supply Connector Piriout oeste tiet Te esee e Fete Coe E E aa a eR Ud Teo desea AER ERE OCR 32 Table 2 16 Rear Sanel LEDen EREN SEENEN ENER EEN EES 33 Table 3 1 IBI icu Reel ELEM 39 TK 8000 User Manual 2 2009 Fastwel v 001 E Fastwel 4S8 TK 8000 List of Figures Figure 1 1 Figure 1 2 Figure 1 3 Figure 1 4 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 2 5 Figure 2 6 Figure 2 7 Figure 2 8 Figure 2 9 Figure 2 10 Figure 2 11 Figure 2 12 Figure 3 1 Figure 3 2 TK 8000 Appearance Rear and Front Views TK 98000 Top View Dirmernslons eoi re rete te ire tiere tcr etri tee toe ret ee ea Pre EE ER e deed Des TK 8000 Front Panel Dimensions and Layout 14 TK 8000 Rear Panel Layout 14 PC 104 J11 Connector Contacts Layout nennen nre nnne 19 PCI 104 J4 Connector Contacts Layout PC 104 Plus VIO Selector J3 Positions D Sub VGA CRT Gonnector eiii teet eroe eens eee D Sub Serial CGonnectors ene emen nnnnnnnnnnnnnnnnnnnnnnnnnnnr inna sana nasa sns nasa sanas ana USB Conpnechors EEEE EEEEEEEEEEEE E EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE D Sub LPT ele Gigabit Ethernet Connectors IDE HDD On Board Connector SATASSORISGIOE eeh CompactFlash dei EE External Power Supply Connector ene nennen nnne nrn nnne nnns Disassembled TK 8000 PC 104 Plus VIO Selector J3 Positions
36. ficantly Therefore the following sections provide mainly general guidelines regarding installation of peripheral devices The details on external devices connection can be found in documentation supplied with these devices For some operations it is necessary to dismount the covers of the system chassis The diagram below shows the TK 8000 disassembled Figure 3 1 Disassembled TK 8000 3 2 1 USB Devices Connection TK 8000 can accept Plug amp Play connection of USB 2 0 computer peripheral devices printers keyboards mice etc All USB devices may be connected or disconnected while the host power is on TK 8000 User Manual 36 2009 Fastwel v 001 E Installation and Setup Fastwel TE TK 8000 3 2 2 CompactFlash Cards Installation CompactFlash socket on the processor module of TK 8000 supports any 3 3 V or5 V CompactFlash ATA type I II cards The CompactFlash slot is accessible via the side opening of the system chassis Note Connection of the CompactFlash cards while the power is on may damage your system Note AK It is recommended to use CompactFlash cards which has been initialized and formatted in this module By default TK 8000 utilizes LBA mode Utilization of CompactFlash cards which has been initialized and formatted in another mode may lead to errors in operation 1 Unscrew the side lid of TK 8000 2 Carefully slide the correctly oriented CF card into the CF slot and gently pre
37. hoenixBIOS Setup program B Find this USB device at the Boot page and use buttons to move it in order to change its boot priority Save changes and reboot the module To get the on line help about the details of BIOS Setup program operation please apply to the screen tips and the integrated help system TK 8000 User Manual 52 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Ley TK 8000 4 6 Custom Menu Selecting Custom from menu bar on the Main Menu displays a menu shown below Main Advanced Intel Security Boot Custom Exit Item Specific Help gt Hardware Honitor Sub Menu Gigabit Ethernet 1 Enabled Gigabit Ethernet 2 Enabled Fastuel Flash Disk Enabled Disable SHI Causes Disabled Watchdog Timer Disabled IT8888 ISA VGA Disabled IT8888 ISA Decode IO Sub Menu gt 118888 ISA Decode Memory Sub Menu F1 TL F9 Esc e gt Enter F10 Temperature Control submenu contains a number of fields with some ACPI settings such as temperature threshold values and control constants Hardware Monitor submenu displays temperatures and voltages supervised by the hardware monitor This menu screen also provides possibility to control other product specific features including Gigabit Ethernet channels Fastwel flash disk SMI sources watchdog timer and IT8888 PCI to ISA bridge TK 8000 User Manual 53 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Ley TK 8000 4 7 Exit Menu
38. iguration mode only TK 8000 User Manual 42 2009 Fastwel v 001 E Installation and Setup Fastwel LE TK 8000 3 4 3 The procedures of watchdog timer programming is described below Watchdog Timer Programming e Enter configuration mode MOV MOV OUT MOV OUT e Write to LDN register a logic device number watchdog timer has logical number 1 MOV MOV OUT MOV MOV OUT e Watchdog timer registers are available for read and write now DX AL DX DX AL DX 302H 46H AL 57H AL 302H 7 AL 303H 1 AL For example to read status register 3eh and to write the value from it back MOV MOV OUT MOV IN OUT e To exit configuration mode MOV MOV OUT MOV OUT 302H 3EH AL 303H DX AL 302H 57H AL 46H AL TK 8000 User Manual 43 2009 Fastwel v 001 E Installation and Setup Fastwel TEN TK 8000 3 4 4 Global Configuration Registers 7h R W Oth Logical Device Number Logical Device Number register index 7h Index 7h 7 1 S Not used Write Read 0 LDN mer cao l l Writing to this register selects logical device 3 4 5 Logical Devices Configuration Registers 30h R W Activate 60h R W I O port base address bits 15 8 61h R W I O port base address bits 7 0 70h R W 00h Primary interrupt select Activate register Index 30h 7 1 Not used Wri
39. ions ie File Action View Window Help e alm amp 2m Double click the System icon to open up your System Properties window Click Hardware and then Device Manager in the System Properties window Locate and right click the driver select Update driver In the opened wizard s window check Yes this time only and press Next In the next window check Install from a list or specific location and press Next To start installation press Next To complete installation press Finish Computer 3 ep Disk drives 2 Display adapters 53 Floppy disk controllers gj Human Interface Devices CN IDE ATAJATAPI controllers C Keyboards Mice and other pointing devices Monitors Bg Network adapters Ports COM amp LPT MR Processors Sound video and game controllers Audio Codecs Legacy Audio Drivers D Legacy Video Capture Devices Media Control Devices NSC 82801BA AC 37 Audi Video Codecs 3 System devices Chipset Driver Installation 1 Click on the win2k_xp chipset folder and then double click on the infinst enu exe In the next window check Don t search will choose the driver to install and press Next Press Have disk button locate and select the driver win2k_xp audio and press OK 2 Follow the instructions of the wizard it will guide you through the installation process LAN Driver Installation 1 Click o
40. it to pack the product for shipping in warranty cases or for safe storage Please pack the product for transportation in the way it was packed by the supplier When handling the product please remember that electronic modules their components and connectors require delicate care Always keep in mind the ESD sensitivity of the product Three Year Warranty Fastwel Co Ltd Fastwel warrants that its standard hardware products will be free from defects in materials and workmanship under normal use and service for the currently established warranty period Fastwel s only responsibility under this warranty is at its option to replace or repair any defective component part of such products free of charge Fastwel neither assumes nor authorizes any other liability in connection with the sale installation or use of its products Fastwel shall have no liability for direct or consequential damages of any kind arising out of sale delay in delivery installation or use of its products If a product should fail through Fastwel s fault during the warranty period it will be repaired free of charge For out of warranty repairs the customer will be invoiced for repair charges at current standard labor and materials rates Warranty period for Fastwel products is 36 months since the date of purchase The warranty set forth above does not extend to and shall not apply to 1 Products including software which have been repaired or altered by other
41. m infringement of these rules Warning A When handling or operating the processor module special attention should be paid to the heat sinking system because it can get very hot during operation Do not touch the heat conducting parts Moreover the processor module should not be placed on any surface or in any kind of package until the module and its heat conducting parts have cooled down to ambient temperature Caution A Always switch off the system power before connecting or disconnecting the power supply cable to the computer s power connector Disregarding this requirement could be harmful for your life or health and can damage the processor module or entire system ESD Sensitive Equipment A This product comprises electrostatically sensitive components Please follow the ESD safety instructions to ensure operability and reliability gi Use grounding equipment if working at an anti static workbench Otherwise discharge yourself and the tools in use before touching the sensitive equipment W Try to avoid touching contacts leads and components il Disconnect power cable before mounting or removing PC 104 or PC 104 Plus expansion module Extra caution should be taken in cold and dry weather TK 8000 User Manual 35 2009 Fastwel v 001 E Installation and Setup Fastwel Ley TK 8000 3 2 Hardware Installation A lot of peripheral devices can be connected to the TK 8000 Their installation procedures differ signi
42. n a Automatic cabling configuration recognition Cabling requirement Category 5 UTP four pair cabling v 001 E TK 8000 User Manual 15 2009 Fastwel Introduction Fastwel Lee TK 8000 Serial ports a COM 1 and COM2 RS 232 two 9 pin D sub rear panel connectors limited functionality see subsection 2 3 4 for details a COMS and COM4 RS 485 or TTL level UART interface 16C550 compatible UART two 9 pin D sub front panel connectors USB Interface a Four USB 2 0 Type A sockets at rear panel a Support for UHCI and EHCI Parallel port Multi Mode parallel port L Standard Mode IBM PC XT PC AT and PS 2 compatible bidirectional parallel port E SPP ECP EPP compatible u Available at rear panel via DB 25 connector VGA CRT Interface u Video controller integrated in 855GME Built in Intel 2D 3D graphics accelerator Supports analog display resolutions of up to 2048 x 1536 16 bit at 75 Hz HW motion compensation for software MPEG2 and MPEG4 decoding Video memory up to 96 MB shared with system a 15 pin D sub VGA rear panel connector Keyboard and Mouse Keyboard and mouse connection via USB connector Audio Interface a AC 97 2 3 compatible controller E Three standard 3 5 mm coaxial rear panel connectors Line In Line Out Mic In Mass Storage Optional internal 2 5 SSD or HDD with Serial ATA or IDE interfaces Fastwel Flash Disk FFD 32 MB soldered NAND flash disk up to 1 GB as an option CompactFlash a CompactFlash Type I II i
43. n the win2k_xp eth folder and then double click on the PRO2KXP exe 2 X Follow the instructions of the wizard it will guide you through the installation process Graphics Driver Installation 1 Click on the win2k_xp graphics folder and select Windows folder Double click on the win2k xp141950 exe Follow the instructions of the wizard it will guide you through the installation process TK 8000 User Manual 40 2009 Fastwel v 001 E Installation and Setup Fastwel LE TK 8000 ISA Bridge Driver Installation 1 Double click the System icon to open up your System Properties window 2 Click Hardware and then Device Manager in the System Properties window 3 Rightclick the driver and select Update driver EJ Computer Management a File Action View Window Help am sa 2m ze Sai g Computer Management Local CH System Tools fg Event Viewer Shared Folders E By Y na74BCCE1834 d Computer Disk drives a fd Display adapters Performance Logs and Alert Device Manager E E Local Users and Groups E S CAN Floppy disk controllers gj Human Interface Devices Gy IDE ATA ATAPI controllers amp ga Storage Removable Storage Disk Defragmenter Disk Management Services and Applications 1 ty Keyboards Mice and other pointing devices Monitors 1 S Network adapters E KE Other devices wag Other PCI Bridge Device Ports COM amp
44. nd before installing other devices on it always ensure that your mains power is switched off Always disconnect external power supply cables during all handling and maintenance operations with this product to avoid serious danger of electrical shock TK 8000 User Manual 5 2009 Fastwel v 001 E Fastwel TES TK 8000 Unpacking Inspection and Handling Please read the manual carefully before unpacking the product disassembling the chassis or mounting devices inside your system Keep in mind the following ESD Sensitive Device A Electronic modules and their components are sensitive to static electricity Even a non perceptible by human being static discharge can be sufficient to destroy or degrade a component s operation Therefore all handling operations and inspections of this product must be performed with due care in order to keep product integrity and operability a Preferably unpack or pack assemble or disassemble this product only at EOS ESD safe workplaces Otherwise it is important to be electrically discharged before touching the electronic modules This can be done by touching a metal part of your system case with your hand or tool It is particularly important to observe anti static precautions when setting jumpers or replacing components E If the product contains batteries for RTC or memory back up ensure that the module is not placed on conductive surfaces including anti static mats or sponges This can c
45. nternal socket true IDE mode a CompactFlash 4 1 specification supported TK 8000 User Manual 16 2009 Fastwel v 001 E Introduction Fastwel Lee TK 8000 1 5 3 Monitoring and Control Thermal Management CPU overtemperature protection is provided by u Internal processor temperature control unit initiates CPU shut down E Processor frequency control conforms to ACPI specification u Processor die temperature monitor can report processor temperature to the user program a Custom designed heat sinking system Temperature Monitor u LM87 hardware monitor for supervision of the on die CPU temperature and the board surface temperature Watchdog Timers u FPGA based programmable watchdog timer E Programmable watchdog timer integrated in 6300ESB ICH LEDs Four LEDs are located on the rear panel u D7 GP Green LED Power E D7 GP Red LED FPGA Xilinx controlled u D8 GP Green LED Super I O controlled a D8 GP Red LED Storage device activity indicator Gigabit Ethernet status 1 and 2 optional u Line yellow Line connected L Act green Network activity 1 5 4 Other Mechanical Aluminum alloy chassis wall mounting Dimensions with wall mount brackets 238 mm x 209 x 82 4 mm 9 4 x 6 5 x 3 2 without brackets 212 mm x 209 mm x 64 4 mm 8 3 x 6 5 x 2 5 see Dimensions Diagram Net weight 3 3 kg 7 28 Ib Gross weight 4 kg 8 82 Ib Power Supply E DC input 9 30 V E Optional external AC DC power adaptor AC in
46. oller Hub Datasheet February 2004 pages 667 671 Serial connectors pinouts are presented in the tables below TK 8000 User Manual 25 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 Table 2 7 Serial Port Connectors COM1 and COM2 Pinouts 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RIN 5 GND Table 2 8 Serial Port Connectors COM3 and COM4 Pinouts 1 Data1 6 Datal 2 NC 7 NC 3 NC 8 NC 4 NC 9 NC 5 GND z Note xX The RS485 interfaces COM3 and COM4 provide for support of up to 256 network segments In case the computer is supposed to serve as a terminal network device it is necessary to mention this fact when ordering TK 8000 The required SMT 120 ohm terminal resistors will be installed at the factory 2 5 USB Interfaces Figure 2 6 USB Connectors 1234 TK 8000 supports four USB 2 0 ports they are available via oo standard A type USB sockets at rear panel All four ports are high speed full speed and low speed capable UHCI compliant Hi speed USB 2 0 allows data transfers of up to 480 Mb s 40 times faster than a full speed USB USB 1 1 One USB peripheral may be connected to each port To connect more than four USB devices use an external hub The USB power supply is protected by a self resettable 500 mA fuse The table below presents the contacts designation of USB connector
47. orrect values may cause system boot failure load Setup Default values to recover lt Up Down gt arrows select fields in current menu lt PgUp PgDn gt moves to previous next page on scrollable menus lt Home End gt moves to top bottom item of current menu Within a field lt F5 gt or lt gt selects next lower value and lt F6 gt lt gt or lt Space gt selects next higher value Cont och Fi 1 F9 Esc e Enter F10 The scroll bar on the right of any window indicates that there is more than one page of information in the window Use lt PgUp gt and lt PgDn gt to display all the pages Pressing Home and lt End gt displays the first and last page Pressing Enter displays each page and then exits the window Press Esc to exit the window Main Menu Selections Main Menu screen offers possibility to set system time and date to enter type specifications and control options for the devices connected to IDE channels Additionally this menu screen gives information on the amount of the detected main and extended system memory and allows to set system response to POST errors Warning Incorrect settings may cause your system to malfunction To correct mistakes return to Setup and restore the Setup Defaults with lt F9 gt and re enter the correct drive parameters TK 8000 User Manual 48 2009 Fastwel v 001 E Phoenix BIOS Setup Fastwel Ley TK 8000 4 2 Advanced Menu The Advance
48. providing different transfer rates Only ATA 33 mode is available at the current version of the processor module providing transfer rates of up to 33 3 MB sec The current version of TK 8000 supports two EIDE channels but only one of them is available for user devices connection Primary channel is used by CompactFlash secondary channel is routed via the standard AT HDD 44 pin onboard connector of the processor module J9 which can be used for connection of EIDE devices Figure 2 9 IDE HDD On Board Connector A standard AT HDD 44 pin IDC connector is 2 H mounted on the top side of the processor module It is possible to connect both secondary master and n Sew ve DM ND ee Ae secondary slave devices to this EIDE channel TL Maximum IDE cable length is 50 cm The pinout of A B the standard AT HDD connector is shown in the table below TK 8000 User Manual 28 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 Table 2 12 Standard EIDE HDD Connector J9 Pinout 1 RESET Reset HD Out 2 GND Ground signal 3 DD7 HD data 7 In Out 4 DD8 HD data 8 In Out 5 DD6 HD data 6 In Out 6 DD9 HD data 9 In Out 7 DD5 HD data 5 In Out 8 DD10 HD data 10 In Out 9 DD4 HD data 4 In Out 10 DD11 HD data 11 In Out 11 DD3 HD data 3 In Out 12 DD12 HD data 12 In Out 13 DD2 HD dat
49. put 100 240 V B Power on off switch at front panel Battery 3 0 V lithium battery for RTC in a battery holder on the processor module use PANASONIC BR2032 or compatible TK 8000 User Manual 17 2009 Fastwel v 001 E Introduction Fastwel Ley TK 8000 Temperature Ranges Operating 40 C 70 C CF or SSD Storage 55 C 85 C Shock 50G peak acceleration 11 ms CF or SSD Vibration 5G RMS 50 500 Hz CF or SSD Humidity RH 5 to 90 non condensing EMC CE FCC Class A 1 5 5 Software BIOS Enhanced Phoenix flash based BIOS Reserved CMOS memory LAN USB Multi boot and Quick boot support ACPI 3 0 Software enable disable function for the Ethernet and COM port configuration Plug amp Play capability Supported Operating Systems Fastwel DOS Microsoft Windows CE5 0 XP XPE Linux 2 4 20 2 6 11 QNX TK 8000 User Manual 18 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 2 Interfaces and Connectors TK 8000 is based on the Fastwel CPC800 02 processor module For information on the features and detailed specifications of this processor module please refer to the CPC800 02 User Manual 2 1 PC 104 and PC 104 Plus Interfaces PC 104 and PCI 104 connectors are located on the processor module of TK 8000 One PC 104 or PC 104 Plus expansion module can be installed on the processor module inside the system chassis however this may require the f
50. rdware monitor voltages and temperature monitoring system control functions LM87 Programmable watchdog timer Additional counters and timers integrated in the ICH Real time clock with Li battery One 1 MB on board FWH for BIOS storage DC 9 30V input with Phoenix connector optional external AC input power adapter Phoenix BIOS TK 8000 User Manual 9 2009 Fastwel v 001 E Introduction Fastwel 48 TK 8000 1 2 TK 8000 Versions At the present time the TK 8000 system is offered in flexible configuration The options include different processors the size of soldered system memory and other options described in this section Other configuration options are available upon request The customer can choose necessary configuration options using the following template 3 2 E 3 4 5 Example Basic product name TK 8000 02 Processor C1 0 Celeron M 1 0 GHz ULV 400 MHz FSB P1 4 Pentium M 1 4 GHz LV 400 MHz FSB P1 8 Pentium M 1 8 GHz 400 MHz FSB Soldered system memory RAM512 512 MB soldered DDR SDRAM RAM1024 1024 MB soldered DDR SDRAM Other options CompactFlash card options CF CF1024 1024 MB industrial CF2G 2 GB industrial CF4G 4 GB industrial CF8G 8 GB industrial CF16G 16 GB industrial 2 5 disk drive installed HDDxx Hard disk drive 2 5 xx GB SSDxx Solid state disk 2 5 xx GB Operating system XPP Windows XP
51. ront panel design changes PC 104 Connector The PC 104 interface accepts an 8 or 16 bit PC 104 expansion modules The PC 104 bus uses a 104 pin 0 10 2 54 mm pitch header located on the top side of the processor module This interface header will carry all of the appropriate 8 MHz ISA bus signals The contact configuration of PC 104 header is shown in Figure 2 1 Two tables below give the designation of this header contacts Figure 2 1 PC 104 J11 Connector Contacts Layout TK 8000 User Manual 19 2009 Fastwel v 001 E Fastwel 4S Interfaces and Connectors TK 8000 Table 2 1 PC 104 J11 Rows A and B Connector Contacts Designation A1 IOCHK B1 GND Ground A2 SD7 In Out B2 RESETDRV Out A3 SD6 In Out B3 5V Power A4 SD5 In Out B4 IRQ9 In A5 SD4 In Out B5 5V A6 SD3 In Out B6 DRQ2 In A7 SD2 In Out B7 12V Power A8 SD1 In Out B8 ENDXFR In AQ SDO In Out B9 12V Power A10 IOCHRDY In B10 KEY A11 AEN Out B11 SMEMW Out A12 SA19 Out B12 SMEMR Out A13 SA18 Out B13 IOW Out A14 SA17 Out B14 IOR Out A15 SA16 Out B15 DACK3 Out A16 SA15 Out B16 DRQ3 In A17 SA14 Out B17 DACK1 Out A18 S
52. s Table 2 9 USB Connectors Pinout 1 VCC VCC signal 2 UVO Differential USB 3 UVO Differential USB 4 GND GND signal TK 8000 User Manual 2009 Fastwel Interfaces and Connectors Fastwel TES TK 8000 2 6 Parallel Port Interface Figure 2 7 D Sub LPT Connector 13 1 SZ EE z4 A Standard parallel port IEEE1284 ECP EPP is available K voovovoooo y Ok via the standard 25 contact female connector at rear panel bs 3 of TK 8000 Its contacts designation is presented below Bei Ke Table 2 10 D Sub LPT Connector Pinout 1 STROBE 14 AUTOFD 2 DO 15 ERR 3 D1 16 INIT 4 D2 17 SELIN 5 D3 18 GND 6 D4 19 GND 7 D5 20 GND 8 D6 21 GND 9 D7 22 GND 10 ACK 23 GND 11 BUSY 24 GND 12 PE 25 GND 13 SEL 2 7 Gigabit Ethernet Figure 2 8 Gigabit Ethernet Connectors F TK 8000 includes two 10Base T 100Base TX 1000Base T Timm 4 Ethernet ports based on the Intel 82546GB dual port Gigabit Ethernet PCI X bus controller Each of the two rear panel Ethernet connectors is realized as an RJ45 connector for twisted pair cabling The Intel 82546GB Gigabit Ethernet controller architecture combines high performance and low power consumption The controller s features include independent transmit and receive queues to limit PCI X bus traffic and
53. set the voltage supplied to PCI interface I O buffers using the J3 VIO selector of the processor module See details below Note To allow an additional amount of distance between the processor module and the expansion module it is recommended to use stackthrough intermediate connectors and additional standoffs ISA 1375795 2 1375795 4 and PCI AMP 1375799 1 AMP 1375799 4 spacers are offered by Tyco AMP SE E 3 2 4 1 PC 104 Plus Voltage Selection The PC 104 Plus voltage should be set before installation of PC 104 Plus expansion modules on the processor module Figure 3 2 PC 104 Plus VIO Selector J3 Positions There is a standard 3 pin header for PC 104 Plus voltage selection The explanation of its jumper positions is presented below wech N Q Contacts 1 2 closed 5 V power is supplied to PCI interface I O buffers D aj w o Contacts 2 3 closed 3 3 V JJ z amk n w TK 8000 User Manual 38 2009 Fastwel v 001 E Installation and Setup Fastwel Lee TK 8000 3 2 5 HDD or SSD Installation Ensure that the computer is off and the power cable is disconnected before proceeding with installation To install a disk drive inside the system chassis it necessary to disassemble the computer 1 Unscrew the rear panel the front panel the CF cover and the bottom lid 2 To assemble the disk drive unit mount the disk on the plate placing four black dumpers between them and tighten four
54. sion of TK 8000 Please refer to the processor module User Manual for detailed description TBA TK 8000 User Manual 32 2009 Fastwel v 001 E Interfaces and Connectors Fastwel TES TK 8000 2 13 LED Indicators There are four LED indicators on the rear panel of TK 8000 Their functions are presented in the table below Table 2 16 Rear Panel LEDs D7 Green General purpose LED controlled by Super I O D7 Red General purpose LED controlled by FPGA Xilinx XC3S200 D8 Green General purpose LED controlled by Super I O D8 Red Storage device activity LED s Default Functions D7 red has no default function programmable only D7 green System Boot State D7 green blinks while system is starting boot sequence and lights up when the boot procedure successfully finished D8 red Storage device activity D8 red lights up while IDE or SATA device is accessed D8 green has no default function programmable only 2 13 1 D7 Red LED Control D7 Red LED is controlled by means of FPGA XILINX XC3S200 using bit 3 LED of the control register Programming sequence e Enter configuration mode MOV DX 302H MOV AL 46H OUT DX AL MOV AL 57H OUT DX AL e Write to LDN register logical device number number 1 the same as WD MOV DX 302H MOV AL 7 OUT DX AL MOV DX 303H MOV AL 1 OUT DX AL e Control register is available via FO index register To read
55. ss to engage the contacts completely 3 X Attach the side lid to the chassis and tighten the screws 3 2 3 Battery Replacement The lithium battery installed on the processor module of TK 8000 must be replaced with Panasonic BR2032 or a battery with similar characteristics The expected life of a 190 mAh battery Panasonic BR2032 is about 5 years However this typical value may vary because battery life depends on the operating temperature and the shutdown time of the system in which the battery is installed Note It is recommended to replace the battery after approximately 4 years to be sure it is operational Note A Always diconnect power supply cables from the processor module before replacing the battery Replacing the battery make sure the polarity is correct up Dispose of used batteries according to the local regulations TK 8000 User Manual 37 2009 Fastwel v 001 E Installation and Setup Fastwel Lee TK 8000 3 2 4 PC 104 and PC 104 Plus Expansion Module Installation The PC 104 and PCI 104 connectors on the processor module of TK 8000 allow you to install interface expansion modules however this may require the front panel design changes Warning When installing any PC 104 or PC 104 Plus module avoid excessively flexing the processor board Mate pins correctly and use the required mounting hardware Note Before installing and operating the PC 104 Plus expansion modules it is necessary to
56. te Read 0 Activate 1 Current logical device enabled 0 Current logical device disabled UO port base address registers Index 60h 7 1 Not used Write Read l O B Ad 15 8 S FO Base Adressl Current logical device base address bits 15 8 Index 61h 7 1 Not used Write Read lO B Ad 7 0 S Base_Adress 7 0 Current logical device base address bits 7 0 TK 8000 User Manual 44 2009 Fastwel v 001 E Installation and Setup Fastwel XE TK 8000 Primary interrupt select register Index 70h 7 4 Not used Write Read 00h Interrupt disabled 01h IRQ1 02h SMI 03h IRQ3 04h IRQ4 05h IRQ5 06h IRQ6 3 0 Interrupt select Sedet ln 08h IRQ8 09h IRQ9 Oah IRQ10 Obh IRQ11 Och IRQ12 Odh IRQ13 Deh IRQ14 Ofh IRQ15 3 4 6 Watchdog Timer Registers Logical Device 1 30h R W Activate 38h Base 0 R W Timer current value 7 0 39h Base 1 RAW Timer current value 15 8 3ah Base 2 R W Timer current value 23 16 3bh Base 3 R W 00h Timer initial value 7 0 3ch Base 4 R W 40h Timer initial value 15 8 3dh Base 5 R W 00h Timer initial value 23 16 3eh Base 6 R W 00h Status register 3fh Base 7 R W 03h Control register 60h R W Base 15 8 UO port base address bits 15 8 61h R W Base 7 3 I O port base address bits 7 3 Base 2 0 should be 0 70h R W 00h
57. than Fastwel personnel unless Buyer has properly altered or repaired the products in accordance with procedures previously approved in writing by Fastwel 2 Products which have been subject to power supply reversal misuse neglect accident or improper installation Returning a product for repair 1 Apply to Fastwel company or to any of the Fastwel s official representatives for the Product Return Authorization 2 Attach a failure inspection report with a product to be returned in the form accepted by customer with a description of the failure circumstances and symptoms 3 Carefully package the product in the antistatic bag in which the product had been supplied Failure to package in antistatic material will VOID all warranties Then package the product in a safe container for shipping 4 The customer pays for shipping the product to Fastwel or to an official Fastwel representative or dealer TK 8000 User Manual 7 2009 Fastwel v 001 E Introduction Fastwel XE TK 8000 1 Introduction 1 1 Overview The product described in this Manual is Fastwel TK 8000 a highly integrated fanless industrial computer with IP52 protection designed to work in harsh environment either as human operated or unattended system at remote location Data acquisition and processing industrial automation transport as well as security are among the major application areas of Fastwel TK 8000 Having inside Pentium M 1 8 GHz CPU with 2 MB
58. the computer Figure 1 4 TK 8000 Rear Panel Layout Line Out Line In VGA The layout may slightly vary for different versions of the computer TK 8000 User Manual 14 2009 Fastwel v 001 E Fastwel 48 Introduction TK 8000 1 5 Technical Specifications 1 5 1 Processor Memory and Chipset CPU TK 8000 is equipped with one of the following Intel amp processors Pentium M B Up to 1 8 GHz a Up to 2 MB L2 on die cache L 400 MHz PSB a Supports SpeedStep III for low power mode Low Voltage Pentium M a Up to 1 4 GHz a Up to 2 MB L2 on die cache E 400 MHz PSB E Supports SpeedStep III for low power mode Ultra Low Voltage Celeron M a Up to 1 0 GHz E Up to 512 KB L2 on die cache E 400 MHz PSB Memory Main system memory E Up to 1 GB of soldered DDR SDRAM memory ECC support a Memory frequency 333 MHz PC2700 Flash memory u 1 MB flash memory Firmware Hub a part of the chipset a One 256 byte EEPROM for storing CMOS data when operating without battery a 30 KB FRAM memory for emergency storage of vital user data 1 5 2 Interfaces PC 104 and PC 104 Plus Interfaces E 16 bit 8 33 MHz ISA bus u 32 bit 33 MHz PCI bus 3 3V 5 0V compatible PCI bus mastering devices are supported Gigabit Ethernet Two 10 100 1000 MB s Gigabit Ethernet interfaces based on Intel 82546GB dual port Ethernet PCI X bus controller u Two RJ45 rear panel connectors a Automatic mode recognitio
Download Pdf Manuals
Related Search