User Manual
Contents
1. Check if the unit is receiving DMX signal and cut it off No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tapping the microphone One of the channels is not working well The stepper motor might be damaged or the cable connected to the PCB is broken The motor s drive IC on the PCB might be out of condition 7 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels DMX INPUT DMX OUTPUT DMX Termination reduces signal errors and to avoid signal e transmission problems and interference Itis always advisable to connect a DMX terminal lt Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the las2. to the music The other units will have to set in slave mode 2L a and select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on Liou 2 light show Cl iyo l l In t o slave mode means the unit works normally and Bi cl means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 5 2 Easy Controller by CA 8 CA 9 The easy remote control is used only in master slave mode By connecting to connector of the first unit you will find that the remote is controller on the first unit will control all the other units for Stand by Function and Mode selection Blackout Blackout the unit 1 Synchronous Strobe Function 2 Two light Strobe Select Show 1 6 Select Gobo 3 Sound Strobe Mode Sound Strobe Show Gobo LED OFF LED ON LED blinking 4 2 Main Function To select any functions press MENU button until the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press ENTER button to setup or it will automatically return to the main functions without any change after idling 30 seconds Back to the functions without any change press MENU button The main functions are shown belo
3. LINKABLE Ses STAND ALONE LED 275 D User Manual Please read the instructions carefully before use Innovation Quality Performance 15 EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN 55103 1 1996 EN 55103 2 1996 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 amp Harmonized Standard EN 60598 2 17 1989 A2 1991 EN 60598 1 2008 EN62471 2008 Safety of household and similar electrical appliances Part 1 General requirements 9 Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days TABLE OF CONTENTS o oo N OOK WOW N Safety Instructions Technical Specifications Installation How To Set The Fixture How To Control The Fixture DMX 512 Configuration DMX 512 Connections Troubleshooting Fixture Cleaning 1 Safety Introductions A WARNING Ple
4. ase read the instructions carefully which includes important information about the installation operation and maintenance Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit Its important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only and use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect mains power before fuse replacement or servicing Replace fuse only with the same type Make sure there are not flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Maximum ambient temperature is TA 40 C and don t operate it where the temperature is higher than this Unit surface temperature may reach up to 60 C Don t touch the housing bare hand during its operation Turn the power off and wait for 15 minutes for cool down before replacing bulb or serving There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely eve
5. ching the unit is secure and is able to support a weight of 10 times of the units weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 4 4 How To Set The Fixture 4 1 Control Panel 1 Display To show the various menus and the selected functions 2 LED pwx Jon BWXimputpresert 4 Safety Ring Keep the installation safe 5 DMX input For DMX512 link use 3 5 pin XLR plug cable to input DMX signal 6 DMX output For DMX512 link use 3 pin XLR plug cable to link the next unit 7 Microphone Receive music for the sound active Mains output Connect to supply mains power for the next unit 9 Mains input Connect to supply mains power 40 CA 9 connector Connect and control the unit via CA 9 D CA 8 connector Connect and control the unit via CA 8 5 3 DMX Controller Use universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the Or js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or
6. how 2 or or show 6 Once select press ENTER button to setup or automatically exit menu mode without any change after 30 seconds To go back to the functions without any change press the MENU button Sound Mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the Lon sound on or sound off Once select press ENTER button to setup or automatically exit menu mode without any change after 30 seconds To go back to the functions without any change press the MENU button I Blackout mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the blackout or normal Once select press ENTER button to setup or automatically exit menu mode without any change after 30 seconds To go back to the functions without any change press the MENU button LED display Press the MENU button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select Lon display on or LoF Fldisplay off mode Once select press ENTER button to setup or exit menu mode without any change after 30 seconds Back to the functions without any change press MENU button again Display Inverse Press MENU button until is blinking on the display Use DOWN and UP button to select normal or inverse press ENTER button to setup Back to the functions w
7. ithout any change press MENU button ICIL C t Self Test Press the MENU button up to when the teot is blinking on the display Pressing ENTER button and the unit will run the built in programmer for self test To go back to the functions press the MENU button Temperature Test Press the MENU button up to when the is blinking on the display Pressing ENTER button and the temperature of the unit will show on the display To go back to the functions press the MENU button e F M 5 Fixture Hours Press the MENU button up to when the Fihie S is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button Lil Software version Press the MENU button up to when the is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button Reset Press the MENU button up to when the is blinking on the display Press ENTER button to reset the unit 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 8
8. nt your fixture may require service please contact the nearest authorized technical assistance center and always use the same type spare parts Don t connect the device to any dimmer pack or power pack Do not look directly at the LED light beam while the fixture is on The housing must be replaced if they are visibly damaged Do not touch any wire during operation as high voltage might be causing electric shock Due to the magnifying type lens please keep the lens out of contact with direct sunlight 3 8 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A 1 The fixture does not work no light Check the connection of power and main fuse Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX connectors cables to see if link properly If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may N cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller Check the LED for the response of the master slave mode signal
9. storing automatically 30 seconds later To go back to the functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 units DMX512 Configuration 255 Rotation Fast Ss 4 246 255 Stop 128 Rotation Slow 138 2551 f 119 127 255 p 100 Fast 108 118 135 245 D s 097 107 086 096 Pasi 075 085 121 134 064 074 053 063 042 052 031 041 020 030 016 019 008 015 000 007 Blackout 15 1374 Shutter 10 120 Slow 0 14 Stop 2 By easy controller 3 By DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 275d on the display and move all the motors to their home position After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in master mode and select 2 show 1 or anc show 2 or ahi 3 show 3 or show 6 mode Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash
10. t fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 5 not used 11 Direct sunlight can cause heat to build up inside of the unit which will seriously damage unit For power supply do not connect in series much more than 37 units use another mains supply for next 37 units 2 Technical Specifications e t can be operated by DMX512 control or can be used as an individual unit without controller e t can be linked together as many as required in master slave mode and perform the great built in programmed lighting shows triggered by music e Please use a 3 pin XLR cable plug when connecting them together e 4 Channels Channel 1 Shutter amp Strobe Channel 2 Gobo Channel 3 Rotation Channel 4 Dimmer e Voltage 100V 240V 50 60Hz e LED 1 x 10W white e Power consumption 16W e Fuse T 6 3A e Dimension 213 x 291 x 183mm e Weight 3 1KG 3 Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are atta
11. w Addr puur DMX512 Address Setting nASE Mater Mode Gi i Slave Mode Normal Gi o Slave mode 2 Light Show Gh O Random Show Gh i Show mode 1 cnmh c Show mode 2 Gh E Show mode 6 Sound Mode on lol IF Yel Sound Mode off Blackout Mode Yes Blackout MENU build moa Blackout Mode No Blackout LED on LED off IC 0 Normal Jaar 7 dS P Inversion LUO Self Test Eee Temperature Test tLe Fixture Hours uE Software Version SPE Reset Odie Lt DMX 512 Address Setting Press the MENU button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically exit menu mode without any change after 30 seconds Back to the previous functions without any change press MENU button 6 Chom Si fa Slave Mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the master or slave 1 or Slave 2 mode Once select press the ENTER button to setup or automatically exit menu mode without any change after 30 seconds To go back to the functions without any change press the MENU button DLA 300 Show Mode Press the MENU button up to when the Shig is shown on the display Pressing ENTER button Use DOWN and UP button to select the Random show or show 1 or S
Download Pdf Manuals
Related Search