ECM-BYT - MSC Technologies
Contents
1. Intel Bay Trail Processors 3 5 Micro Module User s manual 4 Ed 12 November 2014 Part E2047392003R User s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE This guide is designed for experienced users to setup the system within the shortest time For detailed information please always refer to the electronic user s manual Copyright Notice Copyright 2014 Avalue Technology Inc ALL RIGHTS RESERVED No part of this document may be reproduced copied translated or transmi2. Open Closed Closed 2 3 A pair of needle nose pliers may be helpful when working with jumpers Connectors on the board are linked to external devices such as hard disk drives a keyboard or floppy drives In addition the board has a number of jumpers that allow you to configure your system to suit your application If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representative before you make any changes The following tables list the function of each of the board s jumpers and connectors Jumpers Label Function Note JBAT1 Clear CMOS 1 header pitch 2 00 mm JRI1 COM 1 pin 9 signal select 3 x 2 header pitch 2 00 mm JAT1 ATX Input power select 1 header pitch 2 00 mm JBKL SEL1 LCD backlight brightness adjustment 1 header pitch 2 00 mm JTOUCH SEL1 Touch connector select jumper 3 1 header pitch 2 00 mm Connectors Label Function Note BT1 Battery connector 2 X 1 wafer pitch 1 25 mm CPU FAN1 CPU fan connector 4 x 1 wafer pitch 2 54 mm HDMI1 HDMI connector 20 ECM BYT User s Manual User s Manual JAUDIO1 JBKL1 1 2 3 4 JDIO1 JFP1 JLPC1 JLVDS1 JTOUCH1 USB1 2 JUSB3 4 JUSB12 JEC_ROM1 LAN1 LED1 PWR1 JKBMS1 SATA PWR1 SATA1 BIOS 5 1 PCIE1 SO DIMM1 CF1 Audio connector LCD inverter connector Serial port 1 connector Serial port 2 3 4 connector General pu
3. 1024x768 24 1 Default 800x600 18 1 1024x768 18 1 1366x768 18 1 1024x600 18 1 1280x800 18 1 1920x1200 24 2 640x480 18 1 Port1 EDP to LVDS Chrotel 7511 Panel 800x480 18 1 EDID Option 1920x1080 18 2 1280x1024 24 2 1440x900 18 2 1600x1200 24 2 1366x768 24 1 1920x1080 24 2 1680x1050 24 2 00 LVDS Back Light PWM Select LVDS back light PWM duty ECM BYT User s Manual 57 CH7511 EDID Panel Option 5 50 75 100 Default 3 6 3 2 South Bridge Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt Azalia HD Audio High Precision Timer Disabled Enable or Disable the High 9 Enabled Default Precision Event Timer 3 6 3 2 1 Azalia HD Audio Aptio Setup Utility Copyright C 2013 American Megatrends Inc Audio Controller Enabled 58 ECM BYT User s Manual User s Manual Control Detection of the Azalia device Disabled Azalia will be unconditionally disabled Enabled Azalia will be unconditionally Enabled Auto Azalia will be enabled if present disabled otherwise HDMI Port B Enabled Default enable Disable HDMI Port B Disabled 3 6 3 2 2 USB Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc Enabled Default Disabled Audio Controller 0S Selection Hindous 8 X Please select the corresponding type of Windows for OS installation Windows 8 X Default OS Selec
4. Power Technology Enable the power management features 48 ECM BYT User s Manual User s Manual 3 6 2 6 1 Socket 0 CPU Information Setup Utility Copyright C 2013 American Megatrends Inc 3 6 2 7 PPM Configuration Aptio Setup Utility Copyright 2013 American Megatrends Inc Enabled Options Disabled Enable Disable Intel EIST Enabled Default nable Disable Intel SpeedStep Disabled CPU C state Report Enabled Default Enable Disable CPU C state report to OS ECM BYT User s Manual 49 User s Manual This option controls Max C state that the Max CPU C state C1 C6 C7 Default rand processor will Support 3 6 2 8 IDE Configuration aptio Setup Utility Copyright C 2013 American Megatrends Inc Serial ATA SATA Enabled Options Description __ led Defaul Serial ATA SATA Disabled SATA Speed Support SATA Speed Support Gen2 Default Porto ODD SATA ODD Port Port ODD SATA ODD is PortO or Port1 No ODD Default IDE Mode M IDE AHCI Enabled Default Disabled Serial ATA Port 0 1 Enable Disable Serial ATA Port0 1 50 ECM BYT User s Manual User s Manual 3 6 2 9 Network Stack Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc Network Stack Disabled Mem Options
5. Enter the BIOS setup by pressing the delete key during boot up Use the LOAD BIOS DEFAULTS feature The Integrated Peripheral Setup and the Standard CMOS Setup Window must be entered and configured correctly to match the particular system configuration lf TFT panel display is to be utilized make sure the panel voltage is correctly set before connecting the display cable and turning on the power Note Make sure the heat sink and the CPU top surface are in total contact to avoid CPU overheating problem that would cause the system to hang or unstable ECM BYT User s Manual 17 User s Manual 2 2 1 Main Memory ECM BYT provides one 204 pin DDR3L SODIMM socket supports to 8GB DDR3L 1066 1333 SDRAM 47 a 78 DN Oooo e aoocaoamnmoooconQ Oo oo O 29 Rear side Make sure to unplug the power supply before adding or removing SODIMMs or other system components Failure to do so may cause severe damage to both the board and the components e Locate the SODIMM socket on the board e Hold two edges of the SODIMM module carefully Keep away of touching its conneciors e Align the notch key on the module with the rib on the slot 18 ECM BYT User s Manual User s Manual e Firmly press the modules into the socket automatically snaps into the mounting notch Do not force the SODIMM module in with extra force as the SODIMM module
6. Increase the numeric value or make changes Decrease the numeric value or make changes F1 key General help only for Status Page Setup Menu and Option Page Setup Menu F3 key Optimized defaults F4 key Save amp Exit Setup e Navigating Through The Menu Bar Use the left and right arrow keys to choose the menu you want to be in Note Some of the navigation keys differ from one screen to another e To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want Then press Enter pointer marks all sub menus ECM BYT User s Manual 37 User s Manual 3 4 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press Esc or the F1 key again 3 5 In Case of Problems If after making and saving system changes with Setup you discover that your computer longer is able to boot the AMI BIOS supports an override to the NVRAM settings which resets your system to its defaults The best advice is to only alter settings which you thoroughly understand To this end we strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability Even a seemingly small change to the chipset setup has
7. Step 4 Click Finish to complete setup ECM BYT User s Manual 67 ECM BYT User s Manual 4 4 Install VGA Driver Insert the Supporting DVD ROM to DVD ROM drive and it should show the index page of Avalue s products automatically not locate Index htm and choose the product from the menu left or link to Note The installation procedures and screen shots in this section are based on Windows 8 1 operation System Intel amp Installation Framework HI intel Intel Graphics Driver Welcome to the Setup Program This setup program will install the following components Intel Graphics Driver Intel Display Audio Driver Itis strongly recommended that you exit all programs before continuing Click Next to continue Automatically run WinSAT and enable the Windows Aero desktop theme if supported lt Back Next gt Intel Installation Framework Step 1 Click Next to continue installation Intel Graphics Driver intel You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms License Agreement INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By
8. Target PCH Chipset Mixed Platform Date 2014 03 26 For the list of supported chipsets please refer to the Release Notes CONTENTS OF THIS DOCUMENT This document contains the following sections Overview System Requirements Contents of the Distribution Package 3A Public and NDA Configurations 1 oe 1 Step 3 Click Install Intel R Chipset Device Software Completion You have successfully installed the following product Intel R Chipset Device Software Press Finish to complete the setup process View Log Files Step 4 Click Finish to complete setup ECM BYT User s Manual 65 User s Manual 4 2 Install MBI Driver Insert the Supporting DVD ROM to DVD ROM drive and it should show the index page of Avalue s products automatically If not locate Index htm and choose the product from the menu left or link to Utility ECM BYT_ MBI Note The installation procedures screen shots in this section are based on Windows 8 1 operation system If the warning message appears while the installation process click Continue to go on Intel R Sideband Fabric Device Driver Welcome to the Setup Program This setup program will install the following components Intel R Sideband Fabric Device Driver It is strongly recommended that you exit all programs before continuing Click Next to continue
9. s Manual 5 User s Manual 2 4 22 Audio connector 32 2 4 22 1 Signal Description Audio connector JAUDIO 1 32 2 4 23 05 00 0 0 DS eit i aed headed ined Sade 33 2424 Power connector PWR E 34 2 4 25 SATA power connector SATA 1 34 3 BIQS 35 3 1 Le gale O TR 36 3 2 36 3 3 SING A 37 3 4 CASTING ICO 38 3 5 In Gase 15 52 025 8 38 3 6 BIOS 39 3 6 1 s TU 39 3 6 1 1 SY SUS ten dee 39 3 6 1 2 Dalec eee III 39 3 6 1 3 SV SUC TM 39 362 Advanced ra 40 3 6 2 1 40 3 6 2 2 F81216 Super IO Configuration 41 3 6 2 2 1 Serial Port 1 Configuration 42 3 6 2 2 2 Serial Port 2 43 3 6 2 2 3 Serial Port Configuration eee 44 3
10. 1 8 level switch Dual USB upper 2 0 under 3 0 1 0 MINI PCIE HSIC USB 2 0 header 0584604 TOUCH CONTROL PenMount 6000 CONTROL Monitor ECM BYT User s Manual 13 User s Manual 2 Hardware Configuration 14 5 5 User s Manual 2 1 Product Overview JTOUCH1 Oo JOL JTOUCH_SEL1 JBKL SEL1 COM1 JLVDS1 VGA 0581 2 1 JUSB3 4 D0000 ooooo ooooo uae 4 51 D 29 JAUDIO1 CPU 1 ECM BYT User s Manual 15 User s Manual o9 e o O o Le lt 06665066600 000 0009 C SO DIMM1 Q 123 o 18 a 0 02 0 11 1 111 CF1 M_PCIE1 16 ECM BYT Users Manual User s Manual 2 2 Installation Procedure This chapter explains you the instructions of how to setup your system 1 2 3 Turn off the power supply Insert the SODIMM module be careful with the orientation Insert all external cables for hard disk floppy Keyboard mouse USB etc except for flat panel A CRT monitor must be connected in order to change CMOS settings to support flat panel Connect power supply to the board via the ATXPWR Turn on the power
11. ______ Enabled Network Stack 00 Disabled Default Enable Disable UEFI Network Stack 3 6 2 10 CSM Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc CSM Support Enabled Enabled Default CSM Support Disabled Enable Disable CSM Support ECM BYT User s Manual 51 User s Manual GateA20 Active Option ROM Messages INT19 Trap Response Boot option filter Storage Other PCI devices Upon Request Default Always Force BlOS Default Keep Current Immediate Default Postponed UEFI and Legacy Legacy only Default UEFI only Do not launch Default UEFI only Legacy only Do not launch UEFI only Legacy only Default Do not launch UEFI only Legacy only Default UEFI only Legacy only Default UPON REQUEST GA20 can be disabled using BIOS services ALWAYS go not allow disabling GA20 this option is useful when any RT code is executed above 1MB Set display mode for Option ROM BIOS reaction on INT19 trapping by Option IMMEDIATE execute the trap right away POSTPONED execute the traps during legacy boot This option controls Legacy UEFI ROMs priority Controls the execution of UEFI and Legacy PXE OpROM Controls the execution of UEFI and Legacy Storage OpROM Controls the execution of UEFI and Legacy Video OpROM Determines OpROM execution policy for devices other than Network Storage or Vide
12. open Device Manager and view the properties of the network adapters Step 5 Click Finish to complete the setup User s Manual 5 Mechanical Drawing mmm ECM BYT User s Manual 71 User s Manual M cm Ui 0 Min 00 in wie 4900 in 14 5 85 145 05 142 66 HH 151 99 127 67 85 56 Unit mm 72 ECM BYT User s Manual User s Manual p co N 2 sm 7 97 e 000000 5 2 3 E Jd s uf e o9 p 4 9 19 1 80 9 09 e Do o a F a ded 60 09 87 54 137 4 eo 2 139 7 146 05 el 34 CA I 2 y ict co up Co On m Unit mm ECM BYT User s Manual 73
13. To receive the latest version of the 5 manual please visit our Web site at http Awww avalue com tw ECM BYT User s Manual 3 User s Manual Product Warranty Avalue warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Avalue or which have been subject to misuse abuse accident or improper installation Avalue assumes no liability under the terms of this warranty as a consequence of such events Because of Avalue s high quality control standards and rigorous testing most of our customers never need to use our repair service If any of Avalue s products is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU type and speed Avalue s products model name hardware amp BIOS revision number other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs 2 Call your dealer and desc
14. delay is taken form Hub descriptor Auto Default Device power up delay Manual 3 6 2 12 Security Configuration Aptio Setup Utility Copyright 2013 American Megatrends Inc TXE EOP Message Enabled Options Description Disabled TXE EOP Message Enabled Default Send EOP Message Before Enter OS ECM BYT User s Manual 53 5 Disabled Intel AT Enable Disable BIOS AT Code from Running Enabled Default Inter AT Platform PBA 2 Enable Disable BIOS AT Code from Running 3 6 2 13 Lan driver report status Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt Intel R PRO 1000 6 0 24 PCI E Healthy Aptio Setup Utility Copyright 0 2013 American Megatrends Inc Controller 78151298 Child 0 Healthy 54 ECM BYT User s Manual 5 3 6 3 3 6 3 1 Chipset Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt North Bridge North Bridge Aptio Setup Utility Copyright C 2013 American Megatrends Inc Intel IGD Configuration Max TOLUD Dynamic Default 2 GB 2 25 GB 2 5 GB 2 75 GB 3 GB Maximum Value of TOLUD ECM BYT User s Manual 55 User s Manual 3 6 3 1 1 Intel IGD Configuration Aptio Setup Utility Copyright 0 2013 American Megatrends Inc GOP Driver Enabled GOP Dri Enabled Default Enable GOP Driver will u
15. loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT Intel Installation Framework Bak Yes Step 2 Click Yes to accept license agreement 68 ECM BYT User s Manual Intel Graphics Driver Readme File Information Refer to the Readme file below to view the system requirements and installation information README FILE Release Version Production Version Driver Version 15 33 18 3469 Operating System s Microsoft Windows 7 Microsoft Windows 8 Microsoft Windows 8 1 v Omas Intel Installation Framework Step 3 Click Next Intel Graphics Driver intel Setup Progress Please wait while the following setup operations are performed Deleting Registry Key HKLM SOFTWARE Microsoft Windows CurrentVersion Uninstall HDMI Deleting Registry Key HKLM SOFTWARE Intel IGDI Creating Process D BTY 0 VGA VGA 15 33 18 3496 VGA Win32 ICCS SetupICCS exe Deleting File C ProgramData Microsoft Windows Start Menu Programs Intel Intel R HD Deleting File C ProgramData Microsoft Windows
16. of the disks and then launch and turn control over to the operating system While the BIOS is in control the Setup program can be activated in one of two ways By pressing lt Del gt or lt F2 gt immediately after switching the system on or By pressing the lt Del gt or lt F2 gt key when the following message appears briefly at the left top of the screen during the POST Power On Self Test Press lt Del gt or lt F2 gt to enter SETUP If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing lt Ctrl gt lt Alt gt and lt Delete gt keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press F1 to Continue DEL to enter SETUP 36 ECM BYT User s Manual User s Manual 3 3 Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the PageUp and PageDown keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program using the keyboard Main Menu Quit and not save changes into NVRAM Esc key Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu
17. 1 70 305 16316 NN Intel Installation Framework Step1 Click Next to start installation Intel R Sideband Fabric Device Driver License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT x Intel Installation Framework Step 2 Click Yes to accept license agreement 66 ECM BYT User s Manual Intel R Sideband Fabric Device Driver Setup Progress Please wait while the following setup operations are performed Installing Driver Intel R Sideband Fabric Device Version 001 070 305 16316 Copying File C Program Files Intel Intel R MBI Driver uninstall Setup exe Copying File C Prog
18. 13 Low pin count connector JLPC1 __ 7 OLK 25 i poppoo cocos oo 400 2 4 14 Serial port 1 connector 2 E NDCDA 485TXN 1 2 NRXDA_485TXP ORIS 78 RAF 900 000 oo 4 0 28 User s Manual User s Manual 2 4 15 Serial port 2 connector 2 ND 5 6 7 2 4 16 Serial port 3 connector 12 NE 7 8 was ECM BYT User s Manual 29 User s Manual 2 4 17 Serial port 4 connector COM4 COMATSH4 7 708 Doers 30 User s Manual User s Manual 2 4 19 Miscellaneous setting connector JFP1 HDD LED HDD LED User s Manual 31 User s Manual 2 4 21 EC Debug connector ROM 1 c e x ao e ao pocoo Dc 0000 i 2 FRONT LOUT T 8 gt m pocoo pocoo L
19. 225 1106 62 3 6 6 1 Save Changes 63 3 6 6 2 Discard Changes and 63 3 6 6 3 Restore 63 3 6 6 4 Launch EFI Shell from filesystem device 63 A DEIVEGES INS TAN AU OM 64 4 1 lt cic Gav Gi 65 4 2 66 4 3 eR 67 4 4 Install v DIUI eic Ei ME 68 4 5 Install Audio Driver For Realtek 892 69 4 6 Install Ethernet Driver For Intel 2114 70 5 eid ents wna eee 71 User s Manual 7 User s Manual 1 Getting Started 1 1 Safety Precautions Warning Always completely disconnect the power cord from your chassis whenever you work with the hardware Do not make connections while the power is on Sensitive electronic components can be damaged by sudden power surges Only experienced electronics personnel should open the PC chassis Caution Always ground yourself to remove any static charge before touching the CPU card Modern electronic devices are ver
20. 6 2 2 4 Serial Port 4 Configuration eee 45 3 6 2 3 mA Memo gu 46 3 6 2 4 o5 Wake 46 3 6 2 5 Serial Port Console 47 3 6 2 6 GPU 48 3 6 2 6 1 GPU 49 3 6 2 7 PP IMEC OMA CUNATON 49 3 6 2 8 IDE OG AN OVA ee ae 50 3 6 2 9 Network Stack 51 3 6 2 10 SM Cont GUANO 51 3 6 2 11 USB 1 52 3 6 2 12 Security 53 3 6 2 13 Lan driver report status 2 54 3 6 3 2 M 55 3 6 3 1 NON TEE 55 3 6 3 1 1 Iter IGD GOT QUAN OF uses ceed emen eom enis 56 3 6 3 1 2 12 51 51 D 57 3 6 3 2 IB 8 8 58 6 ECM BYT User s Manual User s Manual 3 6 3 2 1 Azalia AAU 58 3 6 3 2 2 WSB OMe 59 3 6 3 2 3 POl Express ConflaUlallOr 5 2 60 3 6 4 gt 60 3 6 5 ESO 61 3 6 6
21. HV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT applies For OEMs IHVs and ISVs LICENSE This Software is licensed for use only in conjunction with Intel component products Use of the Software in conjunction with non Intel component products is not licensed V I accept the terms in the License Agreement intei Corporation Step 2 Click Next lt Back Next gt Cancel Intel Trusted Execution Engine Confirmation You are about to install the following components Intel Trusted Execution Engine Intel Dynamic Application Loader Intel Identity Protection Technology Intel Trusted Connect Service Intel Trusted Execution Engine Completion You have successfully installed the following product Intel Trusted Execution Engine Click here to open log file location
22. I 0000 2 4 22 1 Signal Description Audio connector JAUDIO 1 FRONT JD AUDIO Out ROUT LOUT sense pin 32 ECM BYT User s Manual User s Manual 2 4 23 LVDS connector JLVDS1 65 _ 4 70 pocoo opoo cocoa Dc 0000 og DATA 22 8 1408 DATAS 4 User s Manual 33 User s Manual 2 4 24 Power connector PWR1 EEEE 2 00200 2 47 5 5 OG Fs a j kn Googe 88 2 4 25 SATA power connector SATA PWR1 9 o g o Qu 55 ao CL 34 ECM BYT User s Manual User s Manual 3 BIOS Setup User s Manual 35 User s Manual 3 1 Introduction The BIOS setup program allows users to modify the basic system configuration In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed 3 2 Starting Setup The AMI BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the NVRAM and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one
23. Start Menu Programs Intel R HD Graphics Deleting File C ProgramData MicrosoftlWindows start MenulPrograms Intel R Graphics and Deleting File C ProgramData MicrosoftlWindows Start MenulPrograms Intel Intel R Graphic Deleting File C Users Public Desktop Intel R HD Graphics Control Panel Ink Deleting File C ProgramDataMicrosoftlWindows Start MenulPrograms Intel Intel R Iris TM Deleting File C JUsersPublic Desktop Intel R Iris TM Graphics Control Panel Ink Click Next to continue lt Intel Installation Framework Step 4 Click Next Intel Graphics Driver Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the computer now Yes I want to restart this computer now No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Step 5 Click Finish to complete setup User s Manual 4 5 Install Audio Driver For Realtek ALC892 Insert the Supporting CD ROM to CD ROM drive and it should show the index page of Avalue s products automatically If not locate Index htm and choose the product from the menu left or link to Driver_Audio Realtek ALC892 ECM BYT_ Audio Note The installation procedures and screen shots in this section are based on Windows 8 1 operation system Welcome to the InstallShield Wizard for Realtek High Definit
24. eement carefully INTEL SOFTWARE LICENSE AGREEMENT IMPORTANT READ BEFORE COPYING IN STALLING OR USING Do not copy install or use this software and any associated materials collectively the Software provided under this license agreement Agreement until you have carefully read the following terms and conditions By copying installing or otherwise using the Software you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement An wnt nnmis inntinii ne snn tha Cafhuenen I accept the terms in the license agreement Print not accept the terms the license agreement Cancel Step 2 Click Next to accept license agreement 70 ECM BYT User s Manual Setup Options Select the program features you want installed Install V Intel R PROSet for Windows Device Manager W Advanced Network Services V Windows PowerShell Module Intel R Network Connections SNMP Agent Feature Description Step 3 Click Next Ready to Install the Program 4 intel The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard Bak Cancel Step 4 Click Install to proceed Install wizard Completed To access new features
25. gs 3 6 2 1 Settings Setup Utility Copyright 0 2013 American Megatrends Inc Enable ACPI Auto Configuration Disabled 40 ECM BYT User s Manual User s Manual _______ Options Enable ACPI Auto Disabled Default Enables or Disables BIOS ACPI Auto Configuration Enabled Configuration Enables or Disables System ability to Disabled Hibernate OS S4 Sleep State This Enabled Default option may be not effective with some OS Enable Hibernation Suspend Disabled Enables or Disables System ability to 53 Suspend to RAM Default Sleep OS S3 Sleep State ACPI Sleep State Disabled Default Enabled Off Default PWR On After PWR Fail On AC loss resume Last state Disabled Default 30 sec 40 sec 50 sec 1 min 2 min 10 min 30 min ErP Function Deep S5 Watch Dog Select WatchDog 3 6 2 2 F81216 Super IO Configuration You can use this item to set up or change the F81216 Super configuration for serial ports Please refer to 3 6 2 2 1 3 6 2 2 2 3 6 2 2 3 and 3 6 2 2 4 for more information Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt Serial Port 1 Configuration ECM BYT User s Manual 41 5 5 Serial Port 1 Configuration Set Parameters of Serial Port 1 COMA Serial Port 2 Configuration Set Parameters of Serial Port 2 COMB Serial Port 3 Configuration Se
26. h Touch screen interface with 5 pin 2 0mm wafer be selected to support 4 5 wire screen optional touch screen 1 x SATA x RS232 1 x RS232 422 485 Chipset Valleyview SoC integrated Graphics VGA Mode 2560 x 1600 60Hz Resolution HDMI mode 1920 x 1200 60Hz LVDS mode 1920 x 1080 60Hz Multiple Display HDMI LVDS CRT LVDS CRT HDMI LCD Interface Dual channel 18 24 bit LVDS AC97 Codec Realtek ALC892 Supports 5 1 CH Audio LAN Chip 2 x Intel 1211AT GbE controller Ethernet Interface 10 100 1000 Base Tx compatible ECM BYT User s Manual 11 User s Manual _ Environmental Power Requirement 12V 26V Single power ATX Support 50 53 54 55 ACPI ACPI 3 0 Compliant Power Type 0 C 60 C Operating Temp Optional Wide temp 40 C 85 C 40 C 75 C Optional Wide temp 40 C 85 C Operating Humidity 0 90 relative humidity non condensing Size L x W 4 5 6 5 115mm 165mm Storage Temp 12 ECM BYT User s Manual User s Manual 1 6 Architecture Overview Diagram The following block diagram shows the architecture and main components of PWE 581 ATXSVSB 1 VTK K CHANNEL A va ve e 187 IDR3TL EH 85 HDMI ans Option Trail W25064FWSSIG
27. ion Audio Driver The InstallShield Wizard will install Realtek High Definition Audio Driver on your computer continue click Next Be eo P Step 1 Click Next to continue setup InstallShield Wizard Complete The InstallShield Wizard has st ssfully installed Realtek High Definition Audio Driver Before you can use the program you must restart your computer set Qi Yes want to restart my computer now Ho 1 will restart my computer later Remove any disks from their drives and then click Finish to complete setup Installed Back Finish p Step 2 Click Finish to complete the setup ECM BYT User s Manual 69 User s Manual 4 6 Install Ethernet Driver For Intel 1211AT Insert the Supporting DVD ROM to DVD ROM drive and it should show the index page of Avalue s products automatically not locate Index htm and choose the product from the menu left or link to Driver_Gigabit Intel l211AT ECM BYT LA N Note The installation procedures and screen shots in this section are based on Windows 8 1 operation system Welcome to the install wizard for Intel R Network Connections Installs drivers Intel R Network Connections and Advanced Networking Services WARNING This program is protected by copyright law and international treaties Step 1 Click Next License Agreement Please read the followina license agr
28. n Megatrends Inc Save Changes and Reset save amp reset Save configuration and reset 62 ECM BYT User s Manual User s Manual 3 6 6 1 Save Changes and Reset Reset the system after saving the changes 3 6 6 2 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are discarded The setup program then exits and reboots the controller 3 6 6 3 Restore Defaults This option restores all BIOS settings to the factory default This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS seiting 3 6 6 4 Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shellx64 efi from one of the available filesystem devices ECM BYT User s Manual 63 User s Manual 4 Drivers Installation Note Installation procedures and screen shots this section for your reference and may not be exactly the same as shown on your screen 64 ECM BYT User s Manual User s Manual 4 1 Install Chipset Driver Insert the Supporting DVD ROM to DVD ROM drive and it should show the index page of Avalue s products automatically If not locate Index htm and choose the product from the menu left or link to Driver_Chipset Intel ECM BYT Note The installation procedures and screen shots in this section are based on Windows 8 1 opera
29. nload Disabled VBIOS Disable it will load VBIOS Enable Enable Integrated Graphics Integrated Graphics Enabled Default Device IGD when selected as the Device Disabled Primary Video Adaptor Disable Always disable IGD Enabled Default Enable Enable IGD Turbo Enable uo nane Disabled Disable IGD Turbo Disable Auto Primary Display IGD Default PCle Enabled le Di GFX Boost Disabled Default nable Disable G 0051 Disabled Enable Disable P Audi LITE Mode Default nable isable Protected Audio Video Control SERPENT Mode 64M Default 96M 128M 160M 192M Select DVMT 5 0 Pre Allocated 224M 256M 288M 320M 352M Fixed Graphics Memory size used 384M 416M 448M by the Internal Graphics Device 480M 512M 128MB Select DVMT 5 0 Total Graphics DVMT Total Gfx Mem 256MB Default Memory size used by the Internal Max Graphics Device 128 Aperture Size 256MB Default Select the Aperture Size 56 ECM BYT User s Manual Select which of IGD PCI Graphics device should be Primary Display DVMT Pre Allocated User s Manual 3 6 3 1 2 IGD LCD Control aptio Setup Utility Copyright 2013 American Megatrends Inc LVDS Back Light Frequency 200 Default 300 400 500 LVDS Back Light PWM S Back Light 700 Select LVDS back light PWM Frequency Frequency ik 2k 3k ok Enabled Default Active Internal LVDS eDP gt Ch7511 Active LVDS Ch7511
30. nput power select AT 1 ATX 1 Default 2 4 4 LCD backlight brightness adjustment JBKL_SEL1 PWM Mode 1 DC Mode Default ECM BYT User s Manual 23 User s Manual 2 4 5 Touch connector select jumper JTOUCH_SEL1 5W 4W Default 2 4 6 Touch connector 1 5 1 DODOBE 1 4 1 21 L wy 3 Serm 24 ECM BYT User s Manual User s Manual 2 4 7 Battery connector BT1 8 cosoo 88 2 4 8 CPU fan connector CPU 1 2 187 9 pocoo H User s Manual 25 User s Manual 2 4 9 5 2 keyboard amp mouse connector JKBMS1 ET du So pocoo popoe 0000 3 467 2 VBRIGHT 90000 0000 26 User s Manual User s Manual 2 4 11 On board header for USB2 0 JUSB3 4 NCC NONE NN 7 8 ignal PIN PIN gna s 6 7 5 8 10 ECM BYT User s Manual 27 User s Manual 2 4
31. o 3 6 2 11 USB Configuration The USB Configuration menu helps read USB information and configures USB settings Setup Utility Copyright C 2013 American Megatrends Inc Legacy USB Support Enabled 52 ECM BYT User s Manual User s Manual Description Enabled Default Enables Legacy USB support AUTO option Legacv USB Support Disabled disables legacy support if no USB devices are connected DISABLE option will keep USB Auto nem devices available only for EFI applications This is a workaround for OSew without XHCI hand off support The ownership change should be claimed by driver Enabled This is a workaround for OSes without EHCI EHCI Hand off Disabled Default hand off support The EHCI ownership change should be claimed by EHCI driver Enabled Default XHCI H EANG Q Disabled Enabled Defaul Enable Disabl B M Dri USB Mass Storage Driver Support nab efault nable Disable USB Mass Storage Driver Disabled Support 1 sec 5 sec The time out value for Control Bulk and 10 sec Interrupt transfers 20 sec Default 10 sec 20 sec Default USB mass storage device Start Unit command 30 sec time out 40 sec USB transfer time out Device reset time out Maximum time the device will take before it properly reports itself to the Host Controller Auto uses default value for a Root port it is 100ms for a Hub port the
32. only fit in one direction Mounting Notch Notch Key 111111111111 111 EU LL LER E E I LE REPRE LEE 11111118 T LLL ELE ELLE LEE LE ELLE LL Ejector 204 pin DDR3 SODIMM To remove SODIMM modules push the two ejector tabs on the slot outward simultaneously and then pull out the SODIMM module 1 Please do not change DDR3 SDRAM parameter in BIOS setup to increase your system s performance without acquiring technical information in advance 2 Static electricity can damage the electronic components of the computer or optional boards Before starting these procedures ensure that you are discharged of static electricity by touching a grounded metal object briefly Note ECM BYT User s Manual 19 User s Manual 2 3 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers A jumper is the simplest kind of electric switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either two pins Open Closed Closed 2 3 The jumper settings are schematically depicted in this manual as follows 1 2 3
33. p Utility Copyright 0 2013 American Megatrends Inc Serial Port Enabled Serial Port Enabled Default Enable or Disable Serial Port Disabled COM Auto Default lO 3E8h 5 lO 3F 8h 3 4 5 6 7 10 11 12 Select an optimal setting for lO 2F 8h IRQ 3 4 5 6 7 10 11 12 super IO device lO 3E8h IRQ 3 4 5 6 7 10 11 12 lO 2E8h IRQ 3 4 5 6 7 10 11 12 Change Settings 44 ECM BYT User s Manual User s Manual 3 6 2 2 4 Serial Port 4 Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc Serial Port Enabled Serial Port Enabled Default Enable or Disable Serial Port Disabled COM Auto Default 2 8 IRQ 10 lO 3F 8h 3 4 5 6 7 10 11 12 Select an optimal setting for lO 2F 8h 3 4 5 6 7 10 11 12 super IO device lO 3E8h IRQ 3 4 5 6 7 10 11 12 lO 2E8h IRQ 3 4 5 6 7 10 11 12 Change Settings ECM BYT User s Manual 45 User s Manual 3 6 2 3 H W Monitor Aptio Setup Utility Copyright C 2013 American Megatrends Inc Smart Fan Function Disabled Description E Smart Fan Function Disabl It Enables or Disables Smart Fan 3 6 2 4 S5 RTC Wake Settings Aptio Setup Utility Copyright C 2013 American Megatrends Inc Wake system from 55 Disabled 46 ECM BYT User s Manual User s Manual ________ Options Description Enable or di
34. power select 1 23 244 LCD backlight brightness adjustment JBKL 5 1 23 2 4 5 Touch connector select jumper _5 1 24 2 4 6 Touch connector 1 4 24 2 4 Battery connector 1 25 2 4 8 CPU fan connector CPU 1 25 2 4 9 5 2 keyboard mouse connector 51 26 2 4 10 LCD inverter connector 26 2 4 10 1 Signal Description LCD Inverter Connector JBKL1 26 2 4 11 On board header for USB2 0 5 4 27 2 4 12 On board header for USB2 0 _ 05812 27 2 413 Low pin count connector 2 2 28 2 4 14 Serial port 1 connector 1 28 2 4 15 Serial port 2 connector 2 29 2 4 16 Serial port 3 connector 29 2 4 17 Serial port 4 connector 4 30 2 4 18 General purpose I O connector 30 2 4 19 Miscellaneous setting connector 1 31 24 20 BIOS SPI connector BIOS SPI1 31 2 4 21 Debug connector JEC 32 User
35. ram Files Intel Intel R MBI Driver uninstall Setup cfg Copying File C Windows system32 difxapi dll Click Next to continue Intel Installation Framework Step 3 Click Next to proceed setup Intel R Sideband Fabric Device Driver Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the computer now Yes I want to restart this computer now No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Step 4 Click Finish to complete setup User s Manual 4 3 Install TXE Driver Insert the Supporting DVD ROM to DVD ROM drive and it should show the index page of Avalue s products automatically If not locate Index htm and choose the product from the menu left or link to Utility ECM BYT_TXE Note The installation procedures and screen shots in this section are based on Windows 8 1 operation system If the warning message appears while the installation process click Continue to go on Intel Trusted Execution Engine Welcome You are about to install the following product Intel Trusted Execution Engine Itis strongly recommended that you exit all programs before continuing Click Next to continue or dick Cancel to exit the setup program Intel Trusted Execution Engine License Agreement INTEL SOFTWARE LICENSE AGREEMENT OEM I
36. ribe the problem Please have your manual product and any helpful information available 3 f your product is diagnosed as defective obtain an RMA return material authorization number from your dealer This allows us to process your good return more quickly 4 Carefully pack the defective product a complete Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer 4 ECM BYT User s Manual User s Manual CONTENT 15 Geng 8 1 1 eee 8 1 2 8 1 3 Document Amendment 9 1 4 Manual 10 1 5 SYSTEM 5 11 1 6 Architecture Overview Block Diagram 13 2 JHardware Conti 55445 14 2 1 Product Overview 15 2 2 Installation 17 2 2 1 TUE 18 2 3 dumper and Connector Lisls 20 2 4 Setting Jumpers 22 2 4 1 Clear GMOS JBATI 22 242 1 pin 9 signal select 22 2 4 3 Input
37. rpose connector Miscellaneous setting connector Low pin count interface LVDS connector Touch connector On board connector for USB2 0 x 1 On board connector for USB3 0 x 1 On board header for USB2 0 On board header for USB2 0 EC Debug connector 45 Ethernet connector LED connector Power connector PS 2 keyboard amp mouse connector SATA power connector serial ATA connector 1 VGA connector BIOS SPI connector Mini PCl connector DDR3 SODIMM connector CF card slot 6 x 2 header pitch 2 00 mm 5 X 1 wafer pitch 2 00 mm D sub 9 pin male Note COM 1 support 5422 485 by BIOS setting 5 x 2 header pitch 2 00 mm 6 x 2 header pitch 2 00 mm 5 x 2 header pitch 2 00 mm 5 x 2 header pitch 2 00 mm 20 x 2 header pitch 1 25 mm 5 x 1 header pitch 2 00 mm 5 x 2 header pitch 2 00 mm 5 x 2 header pitch 2 00 mm 3 x 1 header pitch 2 00 mm 2 X 2 wafer pitch 4 20 mm 3 x 2 header pitch 2 00 mm 2 X 1 wafer pitch 2 00 mm D sub 15 pin female 4 x 2 header pitch 2 00 mm ECM BYT User s Manual 21 ECM BYT User s Manual 2 4 Setting Jumpers amp Connectors 2 4 4 Clear CMOS JBAT1 8 E 5 Protect Clear CMOS Default 2 4 2 1 9 signal select JRI1 2 e c pu x ao e ao Default 22 ECM BYT User s Manual User s Manual 2 4 3 AT ATX I
38. s provided in the standard IBM Technical References unless it proved to be necessary to aid in the understanding of this board We strongly recommend that you study this manual carefully before attempting to interface with ECM BYT series or change the standard configurations Whilst all the necessary information is available in this manual we would recommend that unless you are confident you contact your supplier for guidance Please be aware that it is possible to create configurations within the CMOS RAM that make booting impossible this should happen clear the CMOS settings see the description of the Jumper Seitings for details If you have any suggestions or find any errors concerning this manual and want to inform us of these please contact our Customer Service department with the relevant details 10 ECM BYT User s Manual User s Manual 1 5 System Specifications me Celeron Processor J1900 Family Intel Atom Processor E3800 Family BIOS AMI uEFI BIOS 64Mbit SPI Flash ROM Valleyview SoC integrated EC IT8528E System Memory 1 x 204 pin DDR3L 1066 1333 SODIMM up to 8G SSD x CompactFlash Type socket Optional support InnoDIsk CF SATA l H W Reset 15 65535sec min Watchdog Timer 1sec 1min step H W Status CPU amp system temperature monitoring Monitor Voltages monitoring Expansion f x mini PCle mSATA supported chipset PenMount 6000 Built in Touc
39. sable System wake on alarm event Select Fixed Time system will wake on Disabled Default Wake system from S5 Enabled the hr min sec specified Select Dynamic Time System will wake on the current time Increase minute s 3 6 2 5 Serial Port Console Redirection Aptio Setup Utility Copyright 0 2013 American Megatrends Inc Console Redirection Disabled Options Description Disabled Defaul Console Redirection 4 Console Redirection Enable or Disable ECM BYT User s Manual 47 User s Manual 3 6 2 6 CPU Configuration Use the CPU configuration menu to view detailed CPU specification and configure the CPU Aptio Setup Utility Copyright C 2013 American Megatrends Inc k Socket 0 CPU Information ________ Optos Description All Default Number of cores to enable in each processor Active Processor Cores 1 package Disabled Default Wi XP Enabled Disabled for Windows Limit CPUID Maximum XD can prevent certain classes of malicious Disabled buffer overflow attacks when combined with a Execute Disable Bit Enable d Default supporting OS Windows Server 2003 SP1 Windows XP SP2 SuSE Linux 9 2 RedHat Enterprise 3 Update 3 When enabled a VMM can utilize the additional hardware capabilities provided by Virtualization Technology Disabled Intel Virtualization Technology Enabled Default Disabled Energy Efficient Default Custom
40. t Parameters of Serial Port 3 Serial Port 4 Configuration Set Parameters of Serial Port 4 COMD 3 6 2 2 1 Serial Port 1 Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc Serial Port Enabled Serial Port Enabled Default Enable or Disable Serial Port Disabled COM Auto Default lO 3F8h 4 lO 3F 8h IRQ 3 4 5 6 7 10 11 12 Select an optimal setting for lO 2F 8h IRQ 3 4 5 6 7 10 11 12 Super IO device lO 3E8h 3 4 5 6 7 10 11 12 lO 2E8h 3 4 5 6 7 10 11 12 UART 232 UART 232 Default Change the Serial Port as UART 485 RS232 422 485 UART 422 Enabled TERM f 422 485 termination Disabled Default rom GPIO 10M bps SLEW f GPIO 250k bps Default Change Settings UART 232 422 485 42 ECM BYT User s Manual User s Manual 3 6 2 2 2 Serial Port 2 Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc Serial Port Enabled Serial Port Enabled Default Enable or Disable Serial Port udi Disabled COM Auto Default IOz2F8h IRQ 3 lO 3F 8h 3 4 5 6 7 10 11 12 Select an optimal setting for lO 2F 8h 3 4 5 6 7 10 11 12 super IO device lO 3E8h IRQ 3 4 5 6 7 10 11 12 lO 2E8h 3 4 5 6 7 10 11 12 Change Settings ECM BYT User s Manual 43 User s Manual 3 6 2 2 3 Serial Port 3 Configuration Aptio Setu
41. t or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user 2 component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness A Message to the Customer Avalue Customer Services Each and every Avalue s product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments Whether your new Avalue device is destined for the laboratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name Avalue has come to be known Your satisfaction is our primary concern Here is a guide to Avalue s customer services To ensure you get the full benefit of our services please follow the instructions below carefully Technical Support We want you to get the maximum performance from your products So if you run into technical difficulties we are here to help For the most frequently asked questions you can easily find answers in your product documentation These answers are normally a lot more detailed than the ones we can give over the phone So please consult the 5 manual first
42. the potential for causing you to use the override 38 ECM BYT Users Manual User s Manual 3 6 BIOS setup Once you enter the Aptio Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions and exit choices Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu 3 6 1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock Aptio Setup Utility Copyright C 2013 American Megatrends Inc b Intel RC Version 3 611 System Language This option allows choosing the system default language 3 6 1 2 System Date Use the system date option to set the system date Manually enter the day month and year 3 6 1 3 System Time Use the system time option to set the system time Manually enter the hours minutes and seconds Note The BIOS setup screens shown in this chapter for reference purposes only and may not exactly match what you see on your screen Visit the Avalue website www avalue com tw to download the latest ECM BYT User s Manual 39 User s Manual product and BIOS information 3 6 2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub menus Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt ACPI Settin
43. tion system If the warning message appears while the installation process click Continue to go on Intel R Chipset Device Software Welcome You are about to install the following product Intel R Chipset Device Software It is strongly recommended that you exit all programs before continuing Press Next to continue or press Cancel to exit the setup program Step1 Click Next Intel R Chipset Device Software License Agreement INTEL SOFTWARE LICENSE AGREEMENT OEM IRV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note if you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT applies Step 2 Click Accept Intel R Chipset Device Software Readme File Information 4 5 4 4 4 1 4 7 1 4 4 _ 7 _ 4 gt amp 7 Product Intel R Chipset Device Software Version 10 0
44. tion Android Windows 7 Please change the item of OS selection to Windows 7 if you intend to install Windows 7 OS Please change the item of OS selection to Windows 8 X if you intend to install Windows 8 OS XHCI Mode Enabled Default Contro the USB XHCI USB 3 0 functions amp HSIC Disabled function USB 2 0 Support Control the USB EHCI USB2 0 functions Disabled Default Control each of the USB ports 0 3 Enable Enabled Defaul Enable USB per port Disable Use USB port X Disabled settings USB Port 0 1 2 3 Enabled Default Enable Disable USB Port 0 1 2 3 Disabled USB Per Port Control ECM BYT User s Manual 59 User s Manual 3 6 3 2 3 Express Configuration Aptio Setup Utility Copyright C 2013 American Megatrends Inc PCI Express Port 0 Enabled Enabled Default Enable or Disable the PCI Express Port PCI E P 1 2 Disabled 0 1 2 3 in the Chipset Auto Default Speed Gen 2 Configure PCle Port Speed Gen 1 3 6 4 Security Aptio Setup Utility Copyright C 2013 American Megatrends Inc Administrator Password 60 ECM BYT User s Manual User s Manual Administrator Password Set setup Administrator Password User Password Set User Password 3 6 5 Boot Aptio Setup Utility Copyright C 2013 American Megatrends Inc Setup Prompt Timeout 2 Number of seconds to
45. tted in any form or by any means electronic or mechanical for any purpose without the prior written permission of the original manufacturer Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners Technology Inc reserves the right to make changes without notice to any product including circuits and or software described or contained in this manual in order to improve design and or performance Avalue Technology assumes no responsibility or liability for the use of the described product s conveys no license or title under any patent copyright or masks work rights to these products and makes no representations or warranties that these products are free from patent copyright or mask work right infringement unless 2 ECM BYT User s Manual User s Manual otherwise specified Applications that are described in this manual are for illustration purposes only Avalue Technology Inc makes no representation or warranty that such application will be suitable for the specified use without further testing or modification Life Support Policy Avalue Technology s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc As used herein 1 Life support devices or systems are devices or systems which a are intended for surgical implant into body or b Suppor
46. wait for setup Setup Prompt Timeout 1 65535 activation key 65535 0xFFFF means indefinite waiting On Default Select the Keyboard NumLock state Bootup NumLock State nl Of xi j Quiet Boot Disabled Default Enables or disables Quiet Boot option Enabled MEM Enables or disables boot with Disabled Default initialization of a minimal set of devices Fast Boot Enabled required to launch active boot option Has no effect for BBS boot options Enables or disables boot with VGA Support initialization ofa set of Driver Default required to launch active boot option Has no effect for BBS boot options Disabled If Disabled all USB devices will NOT be USB Support Full Initial available until after OS boot If Partial Partial Initial Default Initial USB Mass Storage and specific ECM BYT User s Manual 61 5 USB port device will be available before OS boot If Enabled all USB devices will be available in OS and Post 1 Disabled 52 Devices Support Enabled Default If Disabled PS2 devices will be skipped Disabled Defaul If Disabled NetWork k Dri ill NetWork Stack Driver Support isabled Default 686 ed NetWork Stack Driver will be Enabled skipped Boot Option 1 Set the system boot order 3 6 6 Save and exit Aptio Setup Utility Copyright C 2013 American Megatrends Inc Save Changes and Reset Aptio Setup Utility Copyright C 2013 America
47. y sensitive to static electric charges As a safety precaution use a grounding wrist strap at all times Place all electronic components in a static dissipative surface or static shielded bag when they are not in the chassis 1 2 Packing List Before you begin installing your single board please make sure that the following materials have been shipped 1x 3 5 ECM BYT Micro Module 1x Quick Installation Guide for e 1x AUX 032 daughter board W Audio 4USB e 1 DVD ROM contains the followings User s Manual this manual in PDF file Ethernet driver and utilities VGA drivers and utilities Audio drivers and utilities e 1x Cable set contains the followings 1 Audio cable 12pin 2 0 pitch 1x USB 2 0 cable 10P 2 0mm 10P 2 54mm 1 Serial ATA cable 7 pin standard 1 Wire SATA power cable 15 pin 2P 2 0mm 1 Flat cable 9P M PHD 10P 2 0mm e foam VHB 4622 10mm 20mm 1 1mm 8 ECM BYT User s Manual User s Manual 1 3 Document Amendment History April 2014 Initial Release June 2014 Update Specifications rd September 2014 Update BIOS Setup November 2014 Remove PWR_SB1 connector ECM BYT User s Manual 9 User s Manual 1 4 Manual Objectives This manual describes in detail the Avalue Technology ECM BYT Single Board We have tried to include as much information as possible but we have not duplicated information that i
Download Pdf Manuals
Related Search