VMC1 User Manual
Contents
1. Monitor a Room Station 1 2 Press MON button at the Master or any Room Station to enable that station s speaker microphone Y GREEN Status LED lights up to indicate the room is being monitored All Stations where MUS is active RED STATUS LED lights up can hear audio from the monitored location s Multiple Stations can be monitored simultaneously Press MON again to turn off EN Quick Start Guide Music Audio NOTE VMC1 does not distinguish between audio from a room being monitored and audio from the tuner If a room is to be monitored it is recommended that the tuner be turned off J Set Volume Level at Master Station To change the speaker volume at the Master Station 1 Turn Radio ON to provide an audio source 2 Press MUS button to activate speaker at the Master Station 3 Press Volume plus or Volume minus buttons to adjust level Setting Volume Levels at Room Stations To change the speaker volume at any Room Station 1 Press the Volume or Volume buttons to adjust level Room station will emit a steady tone increasing or decreasing in level depending on the button being pressed This tone eliminates the need to have an audio source active at the Master lower higher Station while setting the desired volume af VOLUME level lt gt Your installer may disable this tone at each room station however doing so will require an active audio source at the Master Unit to set the2. 2 6 Volume controls Plus Minus keypad buttons 7 LED Indicator Lights See Table 3 8 Audio Jack input Mp3 iPod 9 MICROPHONE Green LED MON J 10 LED Status Lights Green Talk Red Busy Up Down Arrow Navigate thru menu Intercom Keypad Buttons Icons Table 2 Intercom Keypad Function Keys Primary Function Aux Function Volume Control Sets volume L Low to M at Master for Medium to H Radio and Program Mode High Number Keys 1 7 Station ID G Aux 1 Auxilliary Function Aux 2 Input 4 Filter Arrow Up FILTER O n mic Unlocks Door Arrow Down LOCK HD PRIV Privacy control JD MON Monitor al MUS Music 2 CLEAR da Exit Program Mode intercom O HOUSE mole House Page DOOR Talk to Door G AUX Switches AUX on off LED Indicator Lights LED Lights Light emitting Diodes indicate status or activity by alerting user with TUNER ON OFF functions blinking or flashing to indicate active status and auxiliary music sources are active They are the status ux music lights for the system and are these colors when not functioning RADIO FILTER Tuner Green Aux Music Green Radio Filter Green Y AS Door Status Red Aux 1 Yellow aux OUTPUT 1 Aux 2 Yellow Table 3 LED Indicator Lights Master Station LED LIGHT Function TUNER Steady Green Radio Source Sele
3. above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state This Linear LLC Warranty is in lieu of all other warranties express or implied Linear Building On Innovation USA amp Canada 800 421 1587 amp 800 392 0123 760 438 7000 Toll Free FAX 800 468 1340 Copyright 2012 Linear LLC in JNE Op ban P1445X2
4. 3 Press and release the radio station channel For locations 1 to 5 simply press that button 4 Press and release the 5 button and then select a button from 1 to 5 to select location 6 to 10 For example pressing 5 and 1 will save the station in location 6 5 Press MEM to store the radio station in the selected location Recall Stored Radio Station 1 Press BAND button to select AM or FM 2 To recall locations 1 through 5 press the desired location 3 To recall locations 6 through 10 press and release 5 4 Immediate press a button from 1 to 5 corresponding to the desired location Pressing 1 will recall location 6 pressing 2 will recall location 7 and so on 5 Press ME UP to scroll through all 10 stored locations This scrolls the stored locations and rolls back to number 1 when 10 is reached Set Radio Alarm Auto On Off 1 With the time displayed press and hold the ALARM button Display changes from current time to alarm time with the minutes blinking 5 Quick Start Guide Clock Radio 2 Use the DOWN and UP buttons to adjust the desired minutes for the alarm operation 3 Press the ALARM button again to switch to hours The Hours will begin to blink 4 Use the DOWN and UP buttons to adjust the desired hour for the alarm to activate Press the ALARM button again The clock display will indicate the alarm status ON or OFF Press DOWN or UP to toggle between ON and OFF Press ALARM to exit programming If the Tuner is not
5. Press 5 for VID1 3 6 for VID2 4 7forVID3 The image remains on the Master Station display for 40 minutes at which time the display will turn off NOTE This will not affect the VIDEO OUT signal To change the view e Press AUX followed by the desired video source G button To turn off the display e Press AUX followed by the active video source If a Video Door Station chime is activated the Master Station Video display is active that door station camera will display on the Master Station video display for 20 seconds then revert to the previously selected view Video Out Control From any room station you can select a a video source to output to VIDEO OUT This video can be viewed from any TV in the house This cannot be done from the Master Station To select a source 1 Press AUX 5 for Video Source 1 2 AUX 6 for Video Source 2 3 AUX 7 for Video Source If a video door chime is activated the Video out switches to the Door camera for a preprogrammed period of time To turn off the video source press AUX active video source G Quick Start Guide Options NightStand Station Audio Input The NightStand Station can be used as a stand alone MP3 player smartphone speaker To listen to your auxiliary audio device 1 Plug the appropriate cable for the selected audio device fitted with a 3 5mm stereo plug at one end into the Audio Input Socket at the bottom of the NightStand Station 2 Plug the other end
6. VMC1 VIDEO SECURITY INTERCOM amp MUSIC SYSTEM QUICK STA RT GUIDE VMCI VIDEO SECURITY INTERCOM SYSTEM FOR THE HOME O gt VOLUME gt O Auxevnc 00900 O moomin AUK AUX PUT PRETER 00600 oar STATUS y yor wo wo LOCK 600 O wouy o FRY MON WYS O auxoumur D O CUR NOIE DOON AUN inear Building On Innovation USA amp Canada 800 421 1587 amp 800 392 0123 760 438 7000 Toll Free FAX 800 468 1340 www linearcorp com VMIC1 Quick Start Guide SAFETY WARNING CAUTION OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK AA AA NO USER SERVICEABLE PARTS gt SEESEPEEE EE INSIDE REFER SERVICING TO DO NOT OPEN QUALIFIED SERVICE PERSONNEL CAUTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product SHOCK WARNING The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALL OR USE THE VMC1 MUST BE INSTALLED BY TRAINED DEAL ERS OR INSTALLERS AND MUST CONFORM TO ALL LOCAL BUILDING AND ELECTRICAL CODES Warning Always follow these safety instructions Reta
7. cal dealer or distributor Linear LLC will return the repaired product freight prepaid within the continental United States There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property revenue or profit or cost of removal installation or reinstallation ANY PRODUCT RETURNED TO LINEAR LLC WITHOUT A RPA NUMBER WILL BE REFUSED This limited warranty is in lieu of any other warranties express or implied including any implied warranty of merchantability or fitness for a particular purpose or otherwise and of any other obligations or liability on the sellers part This limited warranty does not cover damage caused by improper installation acts of God criminal acts the violation of applicable building or electrical codes or the use of non recommended wire cable excluding CAT5 and RG 6 or wall housings Under no circumstances shall Linear LLC be liable for consequential incidental or special damages arising in connection with use or inability to use this product In no event shall Linear LLC liability hereunder exceed the cost of the product covered hereby No person is authorized to assume for us or obligate us for any other liability in connection with the sale of this product Some states do not allow the exclusion or limitation of consequential incidental or special damages so the
8. cted AUX MUSIC Steady Green Auxiliary music input source selected RADIO FILTER Steady Green Radio filter on DOOR STATUS Steady Red Door is open AUX OUTPUT 1 Steady Yellow Auxiliary relay 1 activated AUX OUTPUT 1 Steady Yellow Auxiliary relay 2 activated Master amp Room Stations Green Status Light Blinking flashing Privacy Microphone Muted Green Status Light Steady Microphone active monitoring ON Red Status light Blinking Privacy Microphone Muted Red Status light Steady Audio source playing Intercom function active Limited Warranty 2 Year Limited Warranty Linear LLC warrants these products to be free of defects for 2 years The warranty period begins on either a the date of purchase or installation date of this product or b the date of closing on a new residence in which this product was originally installed The warranty extends to the original user of the product and to each subsequent owner of the product during the term of the warranty Linear LLC will repair or replace at its option parts and materials at no charge Parts supplied under this warranty may be new or rebuilt at the option of Linear LLC If during the warranty period the product appears to have a defect please call your local dealer or installer prior to dismantling Dismantling the product prior to calling our service number may void the warranty Before returning any product to Linear LLC contact your lo
9. e Music amp Audio o 4 Quick Start Guide Clock Radio a aau aaa 6 Master Station Video Display Operation lt lt o 7 Quick Start Guide Video e 7 NightStand Station Audio Input lt lt 8 Help Moni a8 666 CRESS SG REDS EG we OH EE SEE AAA 8 Optional PUG ONS soe x puso ar we ge dhe ja He CR He Ow WW BOR ROR gs we wa pw pe RR 8 Quick Start Guide Options e 8 Master Station Power Up lt lt lt oo 10 Initial Power Up aa we ie ee fate Sa me a aca a ne ee ee 10 Programming Steps e 10 Master Station Diagram hee cay a AAA 11 Intercom Keypad Na ee ee ee ee 12 LED indicator Lights 00 500 de a a D a EEE owes a we 13 Limited Walras rca ee A do eS D EE ee A 14 __ lower higher A VOLUME lt D DA AMi AUX 1 AUX2 INPUT FILTER gt O Ory VID1 ViD2 VID3 LOCK x 9 O GREEN Status PRV MON MUS O RED Status eA fe CLEAR HOUSE DOOR AUX Keep this manual in a safe place for future reference If you lose the manual you can download it from the Linear Web site www linearcorp com Quick Start Guide Intercom Intercom Functions The VMC1 Video Security Intercom System can initiate private room to room conversations and whole house conversations or pages To respond to a call or
10. in these instructions for future system reference DO NOT expose the VMC1 to moisture or fire or shock hazards can occur and impair the warranty DO NOT expose Stations to direct water spray or damage will occur DO NOT attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards and will invalidate your warranty Neither the Master Station nor the Room Stations contain any user serviceable parts REFER ALL SERVICING TO QUALI FIED SERVICE PERSONNEL USE ONLY M amp S Systems replacement parts and have them installed by an M amp S Systems dealer or installer Un authorized substitutions can result in fire electric shock or other hazards and will void the warranty Upon completion of any service or product repair the M amp S Systems dealer or installer should conduct a safety check to ensure safe operating condition Use only a dry cloth to clean the Master Station Room Stations Door Stations and speakers Do not use liquid cleaners or aerosol cleaners TO Clean Video and Camera lens use a clean dry cloth only CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL VMC1 Quick Start Guide Table of Contents Quick Start Guide Intercom 2 Intercom FUNCUONS lt 5 mua dada AR 2 Quick Start Guid
11. of the cable into an MP3 player or smartphone 3 Switch Audio Source Selector at the bottom of the NightStand Station toward the center of the Station 4 Select Music mode on the NightStand Station by pressing the MUS button 5 Ensure that the MP3 player or smartphone is turned a on and playing 6 With the volume of the NightStand Station set to the normal level for communication adjust the output volume on the MP3 player or smartphone so the volume from the NightStand Station is at the desired level NOTE With the switch positioned towards the center of the Station the NightStand Station will not play any music from the Master Station or any audio from Monitored Stations All other functions will continue to function normally Help Menu The HELP MENU summarizes the 2nd function of certain keypad buttons in conjunction with the AUX button 1 Press and release the AUX button twice to view the help menu 2 Press the VOLUME and buttons to navigate between pages 6 3 Press CLEAR to exit the menu NOTE See P 2 of Help menu to view the second function of certain keypad buttons in conjunction with the 7 button Applicable to Double Digit format Only Optional Functions The VMC1 Security Intercom is equipped with functions that require additional accessories Ask you installer if these functions are enabled at your installation Gate Door Status LED This RED LED on the Master station may be configured to indicate if a do
12. or or gate is open or closed Quick Start Guide Options Door Release The VMC1 Security Intercom System supports up to three remote electronic door release mechanisms To activate a door release 1 Press the Door Chime button at a Video Door Station The RED Status LED blinks at all Stations indicating an active Page 2 Press and hold DOOR button at any interior Station to speak to the visitor 3 Release to listen Green Status LED lights at that station to indicate an active microphone 4 Release the DOOR button and light goes off NOTE No other Stations can communicate once the door is answered by another Station 5 The visitor responds hands free 6 Press LOCK button to activate electronic door release Door lock remains open for four 4 seconds and Om then locks NOTE Press LOCK again to reopen as long as the communication is active Only the responding Station can activate the door release preventing accidental door opening when pressing LOCK button Home Automation VMC1 Security Intercom System supports two 3 Control Output switches for AUX Output Operation e Remotely turn on lights e Trigger an alert on an alarm panel G e Activate environmental controls With AUX Output Operations homeowners can activate home automation functions using the following controls Single Digit e Press AUX e Followed by button 1 for AUX 1 or button 2 for AUX2 Double Digit SO e Press 7 e Followed by button 1 for AUX 1 o
13. page there are no buttons to press The response at all stations are hands free and there is no need to stop what you are doing NOTE Door Stations calls are only initiated from the Door Station Room to Room Calling All Stations in the VMC1 system have an ID number Press this number to talk or page another station and have a private conversation Create Groups Multiple Room Stations can be programmed with the same ID to create a Group Groups are treated like a single Room Station Depending on your specific installation and requirements your Stations may he programmed for a single digit or double digit ID If you have more than seven 7 interior Stations including the Master or use AUX OUTPUTS from a Nightstand Station your system should be programmed for Double Digit Operation Single Digit Operation In Single Digit Operation all Stations have an ID from 1 to 7 corresponding to the numbered buttons at all Stations 1 Press Station call number to talk to that station Green Status LED lights up at that station and the RED Status LED blinks at all Stations indicating that the system is active Note that only one conversation can be active at a time 2 Release the button and wait for a response 3 The response from the Paged Station is hands free 4 To initiate a response from the Paging Station press the digit again 5 To end the conversation press CLEAR 6 6 Twenty seconds after last button pre
14. r 2 for AUX 2 Master Station Power Up Master Station The VMC 1 Master Station Console is the central unit for the Video Intercom system and has a video screen to monitor any door equipped with a camera From the Master Unit users can program music add auxiliary devices like MP3 players and computers to enhance functions and speak to visitors ringing the doorbell as well as see them Initial Power Up When you power up the master station displays a blue 1 Q welcome screen showing the applicable software version 1 Press CLEAR to clear screen 2 GD G Enter Program Mode J 2 Press PRIV and MON buttons simultaneously oo GENERAL OPTIONS menu is displayed j A 3 Navigate in PROGRAM MODE 4 Press plus or minus buttons to navigate up or down Om 5 Press up or down keys to alter value 6 Use PREV NEXT MENU to navigate between menus Programming Steps To program your VMC1 system please refer to the Finish Out Guide that came with your installation package Master Station Diagram Table 1 Master Station Functions Key Description Button Primary Function Aux Function 1 Display for Clock Radio Clock Radio Shows Time Shows Radio Keypad Station 2 Clock Radio Keypad Band Switch AM FM 3 5 6 Color LCD 5 6 7 Displays Video Displays Door Video screen VID 1 2 3 Video Cam 4 Speaker Volume Keys Radio Output Monitored Room See 6 Output 5 Intercom Keypad See Table
15. selected AUX followed by INPUT Activate MUS at all Stations where the Radio Alarm to be heard When the Alarm is on the clock will display a large O on the far right of the display da oo SD At the designated time the Master will turn on the tuner at the designated alarm time Only those rooms where MUS is active will the music be heard If the Radio is on and the selected Alarm time is reached the Radio will turn off Radio Filter To reduce background noise or radio interference on the radio the Master Station is equipped with a frequency noise filter to adjust or reduce treble Press AUX button followed by number 4 button at Master to activate the filter The Radio Filter Led will illuminate when the filter is turned on To disable the filter Press AUX followed by the 4 button again NOTE Filter only affects audio from the AM FM radio Enable Aux Music To enable the Aux music there is a 3 5mm input jack on the Master Station as the audio source 1 Press and release AUX 2 Press and release INPUT Green AUX INPUT LED lights up and then Green TUNER LED will turn off This overrides the Radio as the source to all Stations with MUS activated To revert to Radio input simply repeat steps 1 and 2 Quick Start Guide Video Master Station Video Display Operation To see the camera view for any of the three attached cameras on the Master Station 1 Press AUX followed by the desired video source 2
16. ss system times out and RED Status LED light turns OFF In Double Digit Operation Quick Start Guide Intercom Double Digit Operation 11 to 17 all Stations have an 1 D from 21 to 27 Press two digits for the Station to talk to RED Status or 31 to 37 LED blinks at all Stations to indicate the VMC1 system is active NOTE Only one conversation can be active at a time Release the button and wait for a response Response from the Paged Station is hands free To answer back from the Paged Station press 2nd digit again To terminate the conversation press CLEAR 6 System times out after 20 seconds after last button press RED Status LED turns off Whole House Calling 1 2 3 4 5 To initial a whole house Page to all Stations press HOUSE and speak into the microphone A All responses are hands free To continue the conversation press HOUSE and speak To end the conversation press CLEAR System times out after 20 seconds after pressing the last button press RED Status LED turns OFF 69 Other Intercom Functions Listen to Music or access Audio Monitor Input 1 2 Press MUS button at Master or Room Station to enable that station speaker RED Status LED lights Ap up to show it is active Any audio input other Intercom conversations are heard thru speaker Received Intercom Page overrides any audio for the duration of the conversation Press MUS again to turn off
17. volume levels If this is disabled follow the steps under Setting the Volume Level at the Master Station to set the volume levels at the Room Stations PLUS amp MINUS Privacy Press PRIV button to disable microphone This prevents any audio from transmitting The Station continues to receive calls however Point To Point and Whole House pages Page any Station where Privacy is active by following the Room To Room or Whole House Paging instructions J Answer Calls in Privacy Mode 1 Press and release PRIV button to speak Station now functions normally 2 Press and release the PRIV button again to end conversation Station remains in Privacy mode until disabled 3 Press the PRIV button to disable Privacy Mode Quick Start Guide Music Audio Turn Audio Off VOLUME buttons at each station control the audio volume for that station however some audio will still be heard even with the volume adjusted to minimum To turn Audio OFF at any station A Press and hold the MUS button Red light begins to flash slowly To turn the Audio ON Press the MUS button Red light turns off Radio Operation Tune Radio 1 Press POWER button at the master station to turn the radio on 2 Press BAND button to select AM or FM 3 Press DOWN amp UP buttons to tune the desired radio frequency Store Radio Stations VMC1 saves up to ten AM and ten FM stations 1 Press Band to select AM or FM 2 Press and release MEM button
Download Pdf Manuals
Related Search