pg1 locked - Brasseler USA
Contents
1. When turned on the setting values are different from what used to be when turned off Turned off the motor while rotating Turn off after the Motor has stopped 11 Warranty Brasseler USA warrants the handpiece against defects in manufacturing workmanship and materials Brasseler USA reserves the right to analyze and determine the cause of any problem Warranty is voided should the handpiece not be used in accordance with this manual Bulb etc are expendable components and are not covered by this warranty 12 Disposing Product Please consult with Brasseler USA about waste disposal 12 O d Sd BRASSELER USA DENTAL INSTRUMENTATION Forza KIE Classification of Equipment Type of protection against electric shock Class ll equipment E Degree of protection against electric shock Type B applied part ethod of sterilization or disinfection recommended by the manufacture See 7 STERILIZATION 135e Autoclavable Degree of safety of application in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide EQUIPMENT not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrousoxide ode of operation Continuous operation Ay Cautions for Handling and Operation S e Read these safety cautions thoroughly before use and operate the product properly e These instructions will sho2. 3 Connecting the AC Adapter m Insert the AC adapter plug into the AC adapter connector g before plugging into wall outlet Fig 3 NEN Only use the AC adapter with control unit of this product AC Adaptor Fig 3 4 Connecting the Power Cord Insert the Power Cord into the Inlet of AC Adapter Fig 4 AC Cord Fig 4 16 4 Handling the Motor 1 Connecting disconnecting the motor and the motor cord Align and insert firmly the Motor Pin in o the pin holes of the Motor Cord Connector and fasten the Motor Cord Nut securely Fig 5 To remove the Motor Cord from the otor unscrew and detach the motor cord nut and gently pull out the motor cord connector 2 Connecting disconnecting the mo To insert the E type handpiece on the or and the handpiece Motor Insert align handpiece and motor then turn those until its click Positioning pins are aligned To remove the handpiece simply pull out the handpiece from the motor Handpiece not included in Forza ELM set Caution Motor aN Motor Cord Connector Motor Cord Nut Motor Cord Fig 5 Positioning Pin Handpiece Option Motor Insert J s Iel Lo Fig 6 stand the handpiece attachment vertically until the excess solution drains Wipe the handpiece then attach it to the Micromotor e Do not connect or disconne
3. including cables than the recommended separation distancecalculated from the equation applicable to the frequency Radiated RF 3V m 3V m of the transmitter IEC61000 4 3 80MHz to 2 5 GHz Recommended separation distance d 1 2VP d 1 2 P 80MHz to 800MHz d 2 3VP 800MHz to 2 5GHz WhereP is the maximum output power rating of the transmitter in watts Wjaccording to the transmitter manufacturer and d is the recommended separationdistance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol NOTE 1 At 80MHz and 800Mkz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field Strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobiles amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Forza ELM is used exceeds the applicable RF compliance level above the Forza ELM should be observ
4. 20 ZA Caution It might happen if the O Ring becomes depleted e Air Water leak e Air Water does not come off e Vibration e Difficult to connect disconnect the handpiece 9 Error Code If the motor stops due to an abnormality such as a malfunction overload break or incorrect usage it automatically checks the state of the Control Box and detects the cause of the abnormality and displays an error code on the Speed Indicator If an error code is displayed turn on the power again and check whether the same error code is displayed If the same error code is displayed take action by referring to the instructions provided in the Check Remedy column in the following table aie Trouble Cause Check Remedy EO Overcurrent error Detected overcurrent in the circuit Contact Brasseler USA In circuit E Overcurrent error Detected overcurrent in the software Contact Brasseler USA In software E2 Retry Error otor stopped by the overload and not Contact Brasseler USA able to restart E ITRIP Error Faulty Motor or Internal circuit Contact Brasseler USA E5 Overvoltage Input Error Overvoltage is given to the Control Box Contact Brasseler USA E6 LED voltage Error Overvoltage is given more than 3 7V Contact Brasseler USA rom the Internal circuit E8 Overheat Error High temperature safe system is Allow unit to cool and try again unctioni
5. AC adapter for other than the control box of this product e Connect only 4 hole 5 hole or 6 pin tubing e Air Requirements dry free from contamination and oil Use a compressor with a dry air system Install an air filter if necessary Blow out the lines before installation e Do not Autoclave or any other high temperature Sterilization Control Box AC Adapter Motor Cord e If you are using corrosive or harsh solutions please clean the control box etc immediately after use Failure to quickly clean the control box etc can result in damage to the equipment or color changes of the case e The system functions normally in the environment where the temperature is at 0 40 C 32 104 F humidity at 10 85 RH atmospheric pressure at 500 1060hPa and no moisture condensation in the Control Unit Use at outside of these limits may cause malfunction e During vibration the motor and the motor cord may affect computer and LAN cable Noise could be heard during operation near a radio receiver e Turn off the Power Switch after each use If unit is to be stored for long periods of time drain water from unit and hose e Responsibility for operating and maintaining Medical Devices belongs to the user e Store the system in the place where the temperature is at 10 60 C 14 140 F humidity at 10 85 RH atmospheric pressure at 500 1060 hPa and the system is not subject to air with dust sulfur or salinity e When trouble is found send to
6. Brasseler USA x A 1 Set Up Diagram Power Cord Power Switch AC Adapter y Motor Cord E lt AC Adapter Turbine Hose Connector Motor Code Connector Connector Fig 1 2 Specifications lt Control Box gt Model Forza ELSU Rated Input AC28V 50 60Hz Drive Air Pressure 57psi 4bar or less Dimensions W127 x D149 x H54 mm Weight 517g lt Motor gt Model Forza ELS Speed 2 000 40 000min 1 rom Dimensions 22 5x L81 mm Weight 76g lt AC Adapter gt Model NE180 Rated Input AC120V 50 60Hz 41VA Output AC28V 1 3A Fuse FU100 T1 6A 250V FU101 T1 6A 250V Dimensions W100 x D178 x H64 mm Weight 1 4kg 3 Operating Control Box Ay Caution Turbine Hose e Please be sure that there is no air or water coming Peg Connector from Turbine Hose when attaching to control box Se e Screw the Nut properly without unnatural force when you plug into Turbine Hose Connector and Motor Cord Connector Avoid cross threading Tirone nse Fig 1 1 Connect the handpiece turbine tubing from the delivery z unit you are using Fit the turbine hose plug of the delivery unit to the turbine hose connector piping and tighten completely Fig 2 NEN SN e Connect only 4 hole 5 hole or 6 pin tubing Air Requirements dry free from contamination and Motor Cord Plug oil Use a compressor
7. Motor in the autoclave pouch to keep it clean until you use it Sterilization at 121 C 250 F for more than 15 minutes is recommended by EN13060 or EN ISO17665 1 Ay Caution e Do not Autoclave or any other high temperature Sterilization Control Box AC Adapter Motor Cord e Do not lubricate the motor e Do not wipe nor immerse the system in acidic water or acidic solutions e Do not sterilize with dirt on the surface It might cause rust e Do not use Protection Plug without the mounting O Ring It may cause a malfunction If O Ring had damaged replace it immediately O Ring Protection Plug Order Code 0312457102 e You can hang Protection Plug on the anywhere to prevent loosing it e Do not hung the Protection Plug with motor It may drop the motor and cause damage 9 OO E Autoclave Procedure 1 Turn off the power 2 Detach the motor from the motor cord See 2 Connecting discon necting the motor cord 3 Clean the surface of the motor with brush etc Do not use the metal brush and wipe it with the cotton moistened with disinfecting alcohol 4 Screw the Motor Cap to the Motor Fig 11 Put the Autoclave plug to the motor insert Fig 12 5 Insert into an autoclave pouch Seal the pouch 6 Autoclavable up to a max 185 C 275 F ex Autoclave for 20 min at 121 C 250 F or 15 min at 132 C 270 F 6 Keep the handpiece in the autoclave pouch to keep it clean Moto
8. and Ec simultaneously 8 By stepping the Foot Pedal of the delivery system Speed Indicator shows the current air pressure Unit is kgf cm e The displayed air pressure is only a guideline Measure the correct air pressure with the air meter e The unit of displayed air pressure is kgf cm For other unit refer to the NOTICE described in 4 9 Using the Foot Pedal of the delivery system maintain the air pressure between 2 0 4 0 Press M2 key until it beep more than 3 seconds to memorize the upper limit of the air pressure e Default value is set to 3 0 kgf cm2 When the air pressure is not between 2 0 4 0 it is displayed Ec and will not be memorized 10 Press both M2 key and Speed Adjustment Key 4 at the same time until it beep more than 3 seconds once again When the alarm sounds this setting is completed By setting Speed Indicator by pressing Rotation Speed Key to 40 and now it is ready to use at the maximum speed 40 000 min rpm 2 Light Brightness Adjusting Function Brightness of the Fiber Optic can be adjusted from this function 1 Press M2 Key and Speed Adjustment Key A at the same time until it beep more than 3 seconds 2 When the alarm sounds Speed Indicator will change to C1 Pressing the Gear Ratio Select key can change the Speed Indicator and Gear Ratio Lamp C1 gt C2 gt C3 gt 1 Set indicator in C3 Light Brightness adjustment mode Press FWD REV Rotation Key to p
9. function it enables you to use the maximum speed 40 000 min 1 rpm even though the air pressure of the delivery system is not high enough by setting upper and lower limit of the air pressure Do this adjustment function after your purchase 1 Press both key and amp key at the same time for more than 3 seconds 2 With alarm sound Speed Indicator will change to Lower air pressure limit setting mode 3 By pressing the O key Speed Indicator shows Oa and Eh simultaneously 4 By stepping the foot pedal of the delivery system Speed Indicator shows the present air pressure Unit is kgf cm e The displayed air pressure is only a guideline Please measure the correct air pressure with the air meter e The unit of displayed air pressure is kgf cm For other unit please refer the bellow ex 0 1kgf cm 1 422psi 0 098bar 1 0kgf cm 14 22psi 0 98bar 3 0kgf cm 42 67psi 2 94bar 5 Using the foot pedal of the delivery system maintain the air pressure between H F dit Press key for more than 3 seconds to memorize the lower limit of the air pressure Default value is set to 2 5 kgf cm When the air pressure is not between 7 7 i itis displayed 4 and will not be memorized 6 After setting lower limit press O key Speed Indicator will change to te Upper air pressure limit setting mode 7 By pressing the O key Speed Indicator shows 7 and E
10. g simultaneously 8 By stepping the foot pedal of the delivery system Speed Indicator shows the present air pressure Unit is kgf cm e The displayed air pressure is only a guideline Please measure the correct air pressure with the air meter e The unit of displayed air pressure is kgf cm2 For other unit please refer to the ZS NOTICE described in 9 Using the foot pedal of the delivery system maintain the air pressure between eae Press key for more than 3 seconds to memorize the upper limit of the air pressure e Default value is set to 2 0 kgf cm e When the air pressure is not between g 4a itis displayed Ee and will not be memorized 8 10 Press both key and amp key at the same time for more than 3 seconds once again When the alarm sounds the setting is complete By setting Speed Indicator by pressing A key to iT and now it is ready to use at the maximum speed 40 000 min 1 rpm E Light Brightness Adjusting function Brightness of the Fiber Optic can be adjusted using this function 1 Press both key and amp key at the same time for more than 3 seconds 2 With alarm sound Speed Indicator will change to l r By pressing O key change the Speed Indicator to J Light Brightness adjusting mode Press O key to proceed 3 When Speed Indicator changed to 3 5 Default value press Y and adjust the brightness e Default value is set to
11. pull out the handpiece from the motor 00 Fig 7 Caution Lubricated Handpiece should stand and allow oil to drain prior to autoclave cycle Attach to the Motor after excess oil has been completely drained If the oil enters the Motor it may cause malfunction of the Motor 5 Operation Section 1 Insert the power cord plug into an outlet and turn the Power Switch power switch on When you turn on the power switch lamps enero O l and speed indicator will light Symbol Mark Function OFF ON 2 Before using this product make sure to do the Foot Air Calibration function See 6 1 Foot Air Calibration Do this adjustment function after your purchase Once it is adjusted it will be memorized and there is no need to do this everytime 3 Push the handpiece selector to indicate the speed Ugniineleesgsssslenge sz Eses of the attachment you will use Fig 8 Handpiece ae Gea Rato Indicator speed min rpm 16 1 i 2S 100 2 500 l 1 1 H 2 000 40 000 1 5 ived 10 000 200 000 Ee l Fig 8 4 Set the maximum speed using the speed control switches Fig 9 5 Select FWD REV rotation using the FWD REV Select switch Fig 10 9 6 The micromotor operation will be controlled by the air switch foot pedal of the delivery unit 7 TOR Fig 10 6 Convenient Functions E Foot Air Calibration By using this
12. with a dry air system Install an air filter if necessary Blow out the lines before installation Fig 2 2 Connect the motor by aligning the motor cord plug and motor connector piping and insert firmly Tighten completely Fig 3 3 Connecting the AC adapter Insert the AC adapter plug into the AC adapter connector before plugging into wall outlet Fig 4 AC Adaptor Fig 3 NE Only use the AC adapter with control unit of this product AC Cord 4 Connecting the power cord Insert power cord into the inlet of AC Adapter Fig 5 Fig 4 4 Handling the Motor NE Ensure that the motor has completely stopped before handling the motor 1 Connecting disconnecting the motor and the motor cord Motor Cord Mot Connector gor Motor Cord Nut e Connecting To connect align and insert carefully and firmly m I the pins of the connector into the pin holes of the motor and fasten the motor cord nut securely Motor Cord O e Disconnecting To disconnect the motor cord from the motor unscrew and detach the motor cord nut and gently pull out the motor cord connector Fig 6 1 Connecting disconnecting the motor and the handpiece Handpiece Motor e Connecting Insert the E type handpiece in the motor insert and turn until it clicks and positioning mark are aligned Motor Insert e Disconnecting Simply
13. 7 5 V e Adjustable between 5 F5 4 Press key for more than 2 seconds to set the brightness 5 Press both key and amp key at the same time for more than 3 seconds once again When the alarm sounds the setting is complete E Program Function It is possible to memorize settings Speed Gear Ratio Forward Reverse Direction 1 Set the values for Speed Gear Ratio Forward Reverse Direction 2 Press key or key for more than 2 second When the alarm sounds the setting is complete 3 You can use your settings Speed Gear Ratio Forward Reverse by pressing Key 7 Sterilization Sterilize the motor only For the sterilization method we recommend the steam autoclave sterilization method Sterilization is required first time you use and after each patient as noted below Autoclaving ll Ke 1 Turn off the Power CES gt 2 Detach the motor from the Motor Cord Refer to4 1 7 Connecting disconnecting the Motor and the Motor Cord Protection Plug Motor Cap 3 Clean the surface of the motor with brush etc Do not use the metal brush Fig 10 and wipe it with the cotton moistened with disinfecting alcohol 4 Screw the Motor Cap to the Motor Put the protection plug to the motor insert Fig 10 Insert into an autoclave pouch Seal the pouch Autoclavable up to max 135 C 275 F ex Autoclave for 20 min at 121 C 250 F or 15 min at 132 C 270 F 7 Keep the
14. O d Sd BRASSELER USA DENTAL INSTRUMENTATION Clinical Electric OPERATION MANUAL Forza IE Electric Micromotor Standard Electric Micromotor Miniature Please Read this operation manual carefully before use and keep for future reference O J A BRASSELER DENTAL INSTRU MENTATION Forza KE Classification of equipment e Type of protection against electric shock Class Il equipment Oo 13 Sua e Autoclavable e Degree of protection against electric shock Type B applied part Method of sterilization or disinfection recommended by the manufacture See 7 STERILIZATION e Degree of safety of application in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide EQUIPMENT not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide e Mode of operation Continuous operation Ay Cautions for Handling and Operation e Read this manual thoroughly before use and operate the device properly e These instructions will show you how to operate the product safety and prevent danger to your or others They are classified by the degree and or severity of danger All contents relating to safety should be oberserved x Classification of precaution Degree and severity of danger or damage A Warning T an instruction where personal injury or physical damage may A Cauti
15. OTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Specifications may be changed without notice By Your Side in Dentistry gt O BRASSELER USA DENTAL INSTRU MENTATION One Brasseler Boulevard Savannah GA 31419 To order call 800 841 4522 or fax 888 610 1937 Visit our website www BrasselerUSA com 11 02 0085
16. ct the handpiece until the motor has completely stopped e Care should be taken when using any handpiece attachment which requires lubrication Following lubrication 5 Operation Section ae T See 6 1 Foot Air Calibration C Push the Gear Ratio Select Key to attachment you will use Fig 7 Insert the power Cord Plug in AC outlet and turn the Power Switch on When you turn on the Power Switch lamps and speed indicator will come on indicate the speed of the During Speed Setting Indicator display Speed For detail display check table below ee Indicator Speed min rpm 16 1 1 25 100 2 500 11 2 40 2 000 40 000 15 1 20 10 000 200 000 17 Function Power Switch Symbol Mark OFF ON Before using this system make sure to use the Foot Air Calibration function f Z A Mz o i Zs o o mey Gear Ratio Lamp 4 Set the maximum speed using the Rotation Speed l Adjustment Key a v Fig 8 Rotation Speed Display 7 Decrease Fig 8 5 Select FWD REV rotation using the FWD REV Select Key Fig 9 Lamp ON REV Lamp OFF FWD 6 The micromotor operation will be controlled by the air switch Foot Pedal of the delivery unit Fig 9 FWD REV Lamp 6 Convenient Functions 1 Foot Air Calibration By using this function it enables you to use the maximum speed 40 000 min rpm even though the air pressure of th
17. e delivery system is not high enough by setting upper and lower limit of the air pressure Do this adjustment function after your purchase Once it is adjusted it will be memorized and there is no need to do this everytime x 1 Press M2 key and Rotation Speed Adjustment Key at he same time for more than 3 seconds When alarm sounds Speed Indicator will change to C1 Lower air pressure limit setting mode By pressing the FWD REV Rotation key Speed Indicator shows 0 0 and Eb simultaneously By stepping the Foot Pedal of the delivery unit Speed Indicator shows the present air pressure Unit is kgf cm 2 3 4 e The displayed air pressure is only a guideline Measure the correct air pressure with the air gauge e The unit of displayed air pressure is kgf cm For other unit refer to the below ex 0 1kgf cm 0 01MPa 1 0kgf cm 0 1MPa 3 0kgf cm 0 3MPa 5 Using the Foot Pedal of the delivery unit maintain the air pressure between 0 3 1 0 Press M2 key for more than 3 seconds to memorize the lower limit of the air pressure 18 e Default value is set to 0 5 kgf cm e When the air pressure is not between 0 3 1 0 it is displayed Eb and will not be memorized 6 After setting lower limit press Gear Ratio Select Key Speed Indicator will change to C2 Upper air pressure limit setting mode 7 By pressing the FWD REV Rotaion Key Speed Indicator shows 0 0
18. ed to verity normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the Forza ELM b Over the frequency range 150kHz to 80MHz field strengths should be less than 3V m Recommended separation distances between portable and mobile RF communications equipment and the nano400 The Forza ELM is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the Forza ELM can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of transmitter Rated maximum oupi pouer oftransmitter 150KHz to 80MHz 80MHz to 800MHz 800MHz to 2 5GHz d 1 2 4P d 1 2 4P d 2 3 4P 0 01 0 12 0 12 0 23 0 1 0 38 0 38 0 73 1 1 2 12 2 3 10 3 8 3 8 7 3 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies N
19. f a typical commercial or hospital Voltage dips short interruptions and voltage lt 5 Ut gt 95 dip in Ut for 0 5 lt 5 Ut gt 95 dip in Ut for 0 5 cycle ains power quality should environment If the user of the Forza ELM requires continued that of a typical commercial or hospital magnetic field IEC61000 4 8 variations on power supply cycle 40 Ut 40 Ut operation during power mains interruptions it is recommended that input lines IEC61000 4 11 60 dip in Ut for 5 cycles he Forza ELM be powered from an uninterruptible power supply 70 Ut ora battery 30 dip in Ut for 25 cycles lt 5 Ut gt 95 dip in Ut for 5 sec Power frequency 50 60Hz 3A m 3 A m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment NOTE Ut is the a c mains voltage prior to application of the test level 23 Guidance and manufacturer s declaration electromagnetic immunity The Forza ELM is intended for use in the electromagnetic environment specified below The customer or the user of the Forza ELM and manual should assure that it is used in such an environment Immunity test EC60601 test level Compliance level Electromagnetic environment guidance Conducted RF 3Vrms 3Vrms Portable and mobile RF communications equipment should be used no closer IEC61000 4 6 150 kHz to 80MHz to any part of the Forza ELM
20. g operation e Verify that the Speed Control Switch is adjusted within the allowable speed before use e Connect only 4 hole 5 hole or 6 pin tubing e Air Requirements dry free from contamination and oil Use a compressor with a dry air system Install an air filter if necessary Blow out the lines before installation e Do not Autoclave or any other high temperature Sterilization Control Box AC Adapter Motor Cord e The operator is responsible for correct operational control maintenance and inspection x J i e During rotation the motor and the motor cord may affect computer and LAN cable Noise could be heard during operation near a radio receiver e After treatment immediately turn off the power switch and shut off the air supply Remove the power cord if the unit box is not to be used for a long time e Responsibility for operating and maintaining Medical Devices belongs to the user e Store the system in the place where the temperature is at 10 60 C 14 140 F humidity at 10 85 RH atmospheric pressure at 500 1060 hPa and the system is not subject to air with dust sulfur or salinity 14 1 Specifications Control Box AC Adaptor Model Forza ELMU Model AC Adaptor NE180 Rated input AC28V 50 60 Hz Rated input AC120V 50 60Hz 41VA Drive Air Pressure 0 4MPa 4 0kgf cm AC230V 50 60Hz 41VA Dimensions W127 x D149 x H54 m
21. given or not proper from the Check the air pressure of the delivery delivery unit system Check the ERROR CODE in the Speed Indicator Refer to 9 ERROR CODE The rotation speed does no Air pressure is not given or not proper from the Check the air pressure of the delivery rise delivery unit system Air pressure of the delivery unit is lower than the Do 6 1 Foot Air Calibration It beeps when turn on the You are stepping on the Foot Pedal when Do not step the Foot Pedal and turn switch turning on the power switch Safety function on the power switch LED does not light Reached the end of life expectancy Contact Brasseler USA Motor heats up abnormally Coolant air is not given or not proper from the Check the air pressure of the delivery within the Control Box during rotation delivery unit system Water leakage Tubing Motor Cord is not connected correctly Contact Brasseler USA If it is from Control Box something is wrong Check the connection When turned on the setting values are different from what used to be when turned off Turn off the Motor while rotating Turn off after the Motor has stopped 11 LEED Brasseler USA warrants the handpiece against defects in manufacturing workmanship and materials Brasseler USA reserves the right to analyze and determine the cause of any problem Warranty is voided should the handpiece not be used in accordance wit
22. h this manual 12 Disposing of Product Consult with Brasseler USA about waste disposal 22 Symbols ON Camis TUV Rhineland of North America is a Nationally Recognized Testing Laboratory NRTL in the United States and is accredited by the Standards Council of Canada to certify electro medical products with Canadian National Standards Follow the waste of electric and electronic equipment WEEE Directive 2002 96 EC to dispose of the product and accessories Cli Consult operation instructions tual Manufacturer R Type B applied part o E Class II Equipment C This conforms to CE European Directive of Medical equipment directive 93 42 EEC ms Autoclavable up to Max 135 C for detail see Sterilization Marking on the outside of Equipment or Equipment parts that include RF transmitters or that apply RF electromagnetic energy for diagnosis or treatment Guidance and manufacturer s declaration electromagnetic emissions used in such an environment The Forza ELM is intended for use in the electromagnetic environment specified below The customer or the user of the Forza ELM and manual should assure that is Emissions test Emissions test Electromagnetic environment guidance RF emissions CISPR11 Group 1 The Forza ELM uses RF energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic e
23. le up to max 135 C 275 F ex Autoclave for 20 min at 121 C 250 F or 15 min at 132 C 270 F 7 Keep the Motor in the autoclave pouch to keep it clean until you use it Sterilization at 121 C 250 F for more than 15 minutes is recommended by EN13060 or EN ISO17665 1 S e Do not Autoclave or any other high temperature Sterilization Control Box AC Adapter Motor Cord e Do not lubricate the motor e Do not wipe nor immerse the system in acidic water or acidic solutions e Do not sterilize with dirt on the surface It might cause rust e Do not use Protection Plug without the mounting O Ring It may cause a malfunction If O Ring had damaged replace it immediately O Ring Protection Plug Order Code 0312457102 e You can hang Protection Plug on the anywhere to prevent loosing it e Do not hung the Protection Plug with motor It may drop the motor and cause damage L A 8 Mainentance Tighten Protection Plug Motor Cap Fig 10 wo oof Replace the O Ring if it becomes worn and makes it difficult to connect the handpiece or if the air or water leak 1 Changing the O Ring Remove the O Ring at the Motor Insert with a pointed tool and mount the new O Rings into the groove Fig 14 Caution S There are 4 O Rings on the Motor Insert Blue one is thinner than other 3 pieces Ree Make sure to order it a GF O Ring Black p
24. m Output AC28V 1 3A Furs AC120V TR5 T C1 250V otor 19372 T1 6A AC230V TR5 T C1 250V Model Forza ELI 800MA Rotation Speed _ 2 000 40 000 min Dimensions W100 x D178 x H64 mm Dimensions D 22 x H70 mm 2 Component Names Control Box AC Adapter Connector Speed Indicator Motor Cord Connector Gear Ratio Lamp Turbine Hose Connector _ Gear Ratio Select Key Motor FWD REV Select Key 4 Protection Plug Rotation Speed Adjustment Key Motor Cap M1 Key Motor Cord Unshielded 2 2m M2 Key AC Cord Unshielded 2 0m Power Switch 15 AC Adaptor Unshielded cord 5 0m 3 Operating Control Box Caution S Be sure that there is no air or water coming from Turbine Hose when connecting to control box Hand tighten the Nut properly without unnatural force when you plug into Turbine Hose Connector and Motor Cord Connector Connector 1 Connect the handpiece tubing from the delivery Turbine Hose unit you are using Fit the Turbine Hose Plug of the delivery unit to the Turbine Hose Connector piping and tighten completely Fig 1 Turbine Hose Plug Caution Motor Cord Connector e Do not use wet or contaminated air Fig e Install an air filter if necessary Blow out the lines before installation 2 Connecting the Motor Connect the motor by aligning the Motor Cord Plug and insert firmly Tighten it completely Fig 2 Motor Cord Plug
25. ng due to long time use at a high load E Motor Start Error Motor didn t reach the preset speed Contact Brasseler USA in a prescribed period of time Break down of a motor cord wire or internal circuit malfunction EA LED voltage Error Voltage for the LED didin t reach the Contact Brasseler USA preset speed in a prescribed period of time Eb Air Offset Error Lower than preset Lower limit of the air Displayed by Foot Air Calibration pressure function Not a malfunction Ec Air Full Scale Error Higher than preset Upper limit of the Displayed by Foot Air Calibration air pressure function Not a malfunction Air pressure higher than 0 4MPa 4 0kgf cm is given EE EEPROM Error Malfunction of the memory for the Contact Brasseler USA setting values 21 10 Troubleshooting When trouble is found check the following again before contacting Brasseler USA If none of these is applicable or the rouble is not remedied even after action has been taken a failure of this product is suspected Check Remedy Cause Solution Pilot Lamp does not light Power Switch is OFF Turn ON the switch AC Adapter is not connected correctly Check the connection Internal Fuse is blown due to some reason Contact Brasseler USA Lower limit of the air pressure Motor does not run Tubing Motor Cord AC Adapter is not Check the connection connected correctly Air pressure is not
26. on ne a where minor to medium injury or physical A Notice Explains an instruction that should be observed for safety reasons e Do not insert or remove power cord with wet hands electric shock may occur e Be sure not to expose the unit to water It may result in a short or electric shock e Do not use this device near combustibles or in a place where explosion may occur e Do not disassemble as no user serviceable parts inside control unit e Do not hit drop the unit or handpiece Place unit in a stable place e Use the fuse of specified rating T1 6A 250V Ref No FU100 FU101 x A Caution e Forza ELS system can be used with the hose connector that is manufactured in accordance with ISO 9168 type B or type C e Forza ELS system is to be used by qualified personnel for dental treatment only and it is used in dental office only e Place the most priority on patient safety e Rotate before using to check for vibration noise or overheating If any abnormalities occur stop using immediately and contact Brasseler USA e Grasp cord by plug to remove from outlet DO NOT pull or yank on the cord itself e Do not connect disconnect the handpiece during operation e Verify that the Speed Control Switch is adjusted within the allowable speed before use e When you install Control Box or Motor DO NOT bend or twist the tubing or the cord No unnatural force is needed to do the installation e Never use the
27. onnector e The system functions normally in the environment where the temperature is at 0 40 C 32 104 F humidity at 10 85 RH atmospheric pressure at 700 1060hPa and no moisture condensation in the Control Unit Operating outside of these limits may cause malfunction e When you install Control Box or Motor DO NOT bend or twist the tubing or the cord No unnatural force is needed for the installation e Do not use contaminated air by dust or moisture If the air contains water or dust it might cause a malfunction or overheat e Do not connect the Forza ELM micromotor to the Forza ELS It may prevent the LED light from working Unit e Grasp cord by plug to remove from outlet DO NOT pull or yank on the cord itself It may cause a wire disconnection or malfunction Care should be taken not to place the AC Cord near a gas burner Never attempt to repair a burned motor cord Always replace it with a new cord e Prior to use always check for vibration noise and overheatin If any abnormalities are detected stop using immediately and contact Brasseler USA e Be careful not to spill water onto the Unit as this may result in fire or an electric shock dur to a short circuit Motor Handpiece Option e Do not use this product under heavy load for long time It can cause the product to overheat e Do not connect or disconnect the cord until the drive motor has completely stopped e Do not connect disconnect the handpiece durin
28. quipment RF emmissions CISPR11 class B The Forza ELM is suitable for use in all establishments including domestic estabilishments and those Harmonic emissions class A directly connected to the public low voltage power supply network that supplynetwork that spplies IEC61000 3 2 buidings used for domestic purposes Voltage Fluctuations ficker Complies This applies to the AC230V system For AC120V system this is Not applicable emissions IEC61000 3 3 Guidance and manufacturer s declaration electromagnetic immunity used in such an environment The Forza ELM is intended for use in the electromagnetic environment specified below The customer or the user of the Forza ELM and manual should assure that it is Immunity test IEC60601 test level Compliance level Electromagnetic environment guidance 1kV for input output Electrostatic discharge ESD 6kV contact 6kV contact Floors should be wood concrete or ceramic tile If floors are covered 1EC61000 4 2 8KV air 8KV air with synthetic material the relative humidity should be at least 30 Electrical fast transient burst 2kV for power supply 2kV for power supply lines Mains power quality should be that of a typical commercial or hospital IEC61000 4 4 lines No input output line environment Surge IEC61000 4 5 1kV line s to line s 2kV line s to earth 1kV line to line 2kV lines to earth ains power quality should environment e that o
29. r Motor Cap OG m BE until you use it A Caution e Do not lubricate the motor e In case the sterilizer chamber temperature could exceed 135 C 275 F during the dry cycle skip the dry cycle e Always place the handpiece in the center or upper shelf of the chamber as the local temperature at the bottom of chamber could rise beyond the set value e Do not wipe with or clean or immerse in high acid water or sterilizing solutions P 8 Maintenance Fig 11 Autoclave Plug Motor Insert Fig 12 E How to replace the O rings at the insert 1 Remove the worn O rings with a pointed tool like a needle 2 Insert new O rings the O ring grooves Optional O ring Blue Order No 5011004 UO Optional O ring Order No 5011005 UO Fig 13 O rings are total 4 pieces Recognize a blue one it is thinner than other 3 pieces Refer to Fig and make sure the order O ring Blue O ring 10 E Replacing Bulb 1 Loosen Motor Housing and detach from the motor a driver Fig 14 2 Align and insert the connector of the new bulb into th the motor Optional Bulb TA Bulb Pack of 3 Order No Y900 132 nd remove the old light bulb using the small pin like a screw e socket hole securely Screw the motor housing securely to Caution e Make sure to turn off the power e Do not touch
30. roceed 3 When Speed Indicator changed to 3 5 Default value press Speed Adjustment Key aW and adjust the brightness e Default value is set to 3 5 V e Adjustable between 1 6 3 6 4 Press M2 key until it beep more than 3 seconds to set the brightness 5 Press M2 key and Speed Adjustment Key a at the same time for more than 3 seconds once again When the alarm sounds this setting has completed 3 Memory Function It is possible to memorize settings Speed Gear Ratio Forward Reverse Direction After the setting you can use your settings by pressing M1 M2 Key 1 Set the values for Speed Gear Ratio Forward Reverse Direction 2 Press M1 Key or M2 Key until it beep more than 3 seconds The alarm indicates the setting is complete 19 7 Sterilization Sterilize the motor only For the sterilization method we recommend the steam autoclave sterilization method Sterilization is required first time you use and after each patient as noted below d cm Autoclaving Turn off the Power ib 2 Detach the motor from the Motor Cord Refer to4 1 Connecting disconnecting the Motor and the Motor Cord Clean the surface of the motor with brush etc Do not use the metal brush and wipe it with the cotton moistened with disinfecting alcohol Screw the Motor Cap to the Motor Put the Protection plug to the motor insert Fig 10 Insert into an autoclave pouch Seal the pouch Autoclavab
31. the glass section of new bulb 9 Error Code Socket Hole A ee K G oan S Ne 9 a ii Connector Bulb Motor Housing Bulb View from A Fig 14 If the motor stops due to an abnormality such as a malfunction overload breakage or wrong use it automatically checks the state of the control unit and detects the cause of the abnormality and displays an error code on the Speed Indicator If an error code is displayed turn on the same error code is displayed take action b in the following table he power again and check whether t y referring to the instructions provided in the Check Remedy column he same error cord is displayed If Error Code Trouble Cause Check Remedy Ea Overcurrent error In circuit Detected overcurrent in the circuit Contact Brasseler USA Ei Overcurrent error In software Detected overcurrent in the software Contact Brasseler USA Ef Retry Error Motor stopped by the overload and not able to restart act Brasseler USA ITRIP Error Faulty Motor or Internal circuit act Brasseler USA ES Overvoltage Input Error Overvoltage is given to the Control Box act Brasseler USA ER Bulb voltage Error Overvoltage is given more than 3 7V from the Internal circuit act Brasseler USA E Overheat Error High temperature safe system is functioning due to long time use at a high load Allow unit to cool then try again e Motor didn t reach
32. the preset speed in a values prescribed period of time Contact Brasseler USA EF Motor Start Error Break down of a motor cord wire or internal circuit malfunction Voltage for the Bulb didn t reach the preset G tB ler USA ERA Bulb voltage Error speed in a prescribed period of time OMAC BrASSEIGT Mors Lower than preset Lower limit of the air Displayed by Foot Air Calibration Eb Air Offset Error pressure P function Not a malfunction e Higher than preset Upper limit of the air _ ea E pressure Displayed by Foot Air Calibration e Air Full Scale Error e Air pressure higher than 57psi 4bar is function Not a malfunction given EE EEPROM Error Malfunction of the memory for the setting Contact Brasseler USA 11 10 Troubleshooting If the motor stops due to an abnormality such as a malfunction overload breakage or wrong use it automatically checks the state of the control unit and detects the cause of the abnormality and displays an error code on the Speed Indicator If an error code is displayed turn on the power again and check whether the same error cord is displayed If the same error code is displayed take action by referring to the instructions provided in the Check Remedy column in the following table Check Remedy Cause Solution Power Switch is OFF Turn ON the switch Pilot Lamp does not light AC Adapter is not connected correctl
33. w you how to operate the product safely and prevent danger to you or others They are classified by the degree and or severity of danger All contents relating to safety should be observed x A Classification Degree and severity of danger or damage N WARNING Provides an instruction where personal injury or physical damage may occur N CAUTION Provides an instruction where minor to medium injury or physical damage may occur NOTICE Provides an instruction that should be observed for safety reasons Peas Warning K e TO PREVENT ELECTRIC SHOCK Do not unplug the power cord with wet hands e TO PREVENT ELECTRIC SHOCK Be sure to prevent water on the Control Box e TO PREVENT ELECTRIC SHOCK Do not unplug the power cord roughly e TO PREVENT ELECTRIC SHOCK Use an electrical outlet that is grounded e If you feel any abnormality such as vibration heat generation abnormal noise etc prior or during use of the unit stop using it immediately e Use the fuse of specified rating AC120V T1 6A 250V Ref No FU100 FU101 AC230V 250V Ref No FU100 FU101 p 13 e When operating this system always consider the safety of the patient e The product is designed only for clinical use by qualified personnel e Every connection must be firmly connected e Do not allow any impact on the Product Do not drop the Product e This system can be used with ISO 9168 type B or type C type hose c
34. y Check the connection Internal Fuse is blown due to some reason Contact Brasseler USA Hk or Cord AC Adapter is not connected Check the connection Matar does hak ru Air pressure is not given or not proper from the Check the air pressure of the delivery system lelivery unit Check the ERROR CODE in the Speed Indicator See 9 ERROR CODE The rotation speed does not rise Air pressure is not given or not proper from the livery unit Check the air pressure of the delivery system Air pressure of the delivery unit is lower than the Lower limit of the air pressure Do 6 1 Foot Air Calibration It beeps when turning on the switch You are stepping on the foot pedal when turning on the power switch Safety function Do not step the foot pedal and on the power switch urn Light Bulb does not light Light Bulb is not connected correctly nsert the Light Bulb correctly and firmly See 8 2 Replacing Bulb Light Bulb is burnt out because of the life Please replace the Bulb See 8 2 Replacing Bulb Motor heats up abnormally during rotation Coolant air is not given or not proper from the delivery unit Check the air pressure of the delivery system Water leakage Tubing Motor Cord is not connected correctly Check the connection If it is from Control Box something is wrong within the Control Box Contact Brasseler USA
Download Pdf Manuals
Related Search