User Manual MEG · DRY · MOA · REG 2 · REG 3
Contents
1. Heater is off it cannot be turned on Diodes do not work No power supply Electronics failure Check that the heater is correctly connected If the connection is correct the product must be returned for repair Device heats without control it cannot be turned off Electronics damage Product requires repair at an authorized repair point Turning the heater on causes the electrical instal lation s safety devices to activate Mechanical damage to de vice resulting from exces sive pressure inside the ra diator i e no air cushion Product requires repair at an authorized repair point Damage of electric iso lation of the heating ele ment or other damage Please contact an electri cian in order to verify the source of the problem Alternatively contact an authorized service point User manual MEG DRY MOA REG 2 REG 3 MOA temperature regulation dryer function turn on off button Turning the device on with the button will result in the radiator heating up to the set temperature After reaching the set temperature the device will turn off and on regularly in order to maintain the set temperature The construction of the device as well as the physical characteristics of the heating agent inside the radiator influence the way in which the heat is distributed the tem perature of the bottom pipes on the ra diator especially the two locate2. MEG DRY MQOA REG 2 REG3 User Manual Our products have been designed and manufactured in such a way to ensure that all quality functionality and aes thetic requirements are met We would like to congratu late you on the purchase of this great product and wish you a pleasant experience with it Electric radiator Guide to safe installation and use 1 Do not install the heater under an electrical socket point 2 Your electric heater should be filled with a carefully measured amount of liquid In the case of loss of heat ing medium or in any other case which demands its supplementation contact your supplier 4 The device is not equipped with an external tempera ture controller Do not use the device in a small room if unsupervised disabled or incapacitated individuals are inside it Only use the device if those individuals are under constant supervision Does not apply to selected models Ask your supplier for details Electric heater is not a toy Children under the age of 3 should not be allowed within close proximity of the device without the supervision of an adult Children aged 3 to 8 should only be allowed to oper ate the heater when it has been properly installed and connected The child must be under adult supervi sion or have been trained to safely operate the device while understanding the risks Note Some parts of the radiator can be very hot and can cause burns Pay special attenti
3. chosen value Device malfunction alert DRY Heater has built in malfunction moni oring and alert functions Device malfunction is signalled in the fol owing way the two outer diodes shine with constant light while the middle diode flashes in the following manner sever al flashes followed by a longer break The number of diode flashes indicates an error code as described below a Running in dry conditions error code 2 flashes electronic system identi fied a situation indicating too little heat ing liquid inside the towel rail Check to see if the towel rail has been properly filled with heating medium b Overheating error code 3 flashes he temperature of heating liquid inside he towel rail is too high e Ifthe heater heats up despite being urned off it is likely that the elec tronics have been damaged The heater should be returned to the supplier manufacturer for repair e Ifthe heater is installed inside a tow el rail that is connected to a central heating system with hot water in the system an alert does not mean hat the heater has been damaged The alert signals that temperature of the installation is too high Please ensure that temperature of the wa ter inside the installation does not exceed 82 C as this could cause damage to the heater s thermal fuse c Temperature sensor damaged error code 4 flashes There is a possibility of electronic syst
4. manual Ensure that the heater has been installed on a wall in accordance with its installation manual Please forward this instruction manual to the end user User manual MEG DRY MOA REG 2 REG 3 Electric Heating Element Safety requirements installation 1 Fitting and connection of the heating element should only be performed by a qualified installer 2 Connect the unit to a sound electrical installation see the ratings on the heater 3 Switching on the heating element inthe open airto test the device is permitted for a maximum of 3 seconds 4 Never test a heating element that is already in stalled Do not turn the heating element on in an empty radiator 5 Ensure that the power cord does not touch the hot parts of the heating element or radiator User manua MEG DRY MOA REG 2 REG 3 6 Before installing or removing the device make sure it is disconnected from the power source 7 Do not open the device any interference with inter nal components will invalidate the warranty 8 The heating element s power output must not ex ceed the radiators power output for the parameters 75 65 20 C 9 The pressure in the radiator should not exceed 10 atm Ensure that an air cushion is preserved in electric radi ators In central heating systems leave one valve open to prevent pressure build up due to the thermal ex pansion of the liquid 10 The device is in
5. of the faulty device at the Manufacturer s premises Should the repair be impossible then the manufacturer is obliged to replace the faulty Product with a new full value unit of identical parameters
6. start blinking on the display panel Use and buttons to set one of the 5 possible maxi mum temperatures The first diode stands for 45 C The following diodes refer to the 3 6 following maximum temperatures 50 C s On O o o o K 9 by ee 55 C 60 C and 65 C a my 8 After selecting the new temperature span press on off button to store the new settings Problem solving Problem Solution The device is plugged in no diodes are on Problem with the connection Possible cause Check the connection of the power wire the plug and the socket Heating element is not heating outside diodes are blinking alternately Temperature sensor has been damaged Disconnect the device completely wait until the radiator cools down and re connect it again Overheating of device Check that the radiator has been filled with the correct heating agent in a proper manner i e ac cording to the manufactur er s instructions The device is heating de spite turning it off with the button Damaged electronics Disconnect the device completely wait until the radiator cools down and re connect it If the problem continues please contact Your local Distribu or 23 24 REG 2 Ring indicating that the device is operating After the device is turned on it heats the radiator up to 65 C Having reached that temperature the device will turn on and of
7. d at the very bottom of the radiator may be low er than the temperature of the remain ing parts of the radiator this is a normal phenomenon Temperature increase In order to increase the temperature of the radiator press once or several times as required the correct number of diodes will start blinking The last blinking diode indi cates the set temperature whilst the last diode which shines constantly indicates the current temperature The remaining di odes will start shining constantly on reach ing subsequent temperature levels Temperature decrease In order to decrease the temperature of the radiator press once or several times as required the correct number of diodes will start blinking The last diode which shines continuously indicates the set tem perature whilst the last blinking diode in dicates the current temperature The re maining diodes will start fading on reaching subsequent temperature levels 21 22 Anti freeze function When the device is off and the temperature surrounding the temperature sensor drops to below 6 C the device will switch on au tomatically This is to prevent the heating agent inside the radiator from freezing The activation of Anti freeze mode is indicated by the blinking of the middle diode Dryer function The Dryer turns the device on for 2 hours e g in order to dry a towel After this peri od of time the device automatically switch es to t
8. em malfunction The heater will most likely need repair d Warning against possible heat escape into the system in central heating instal lations error code 5 flashes there is a risk of a heat escape into the sys tem if device is operating with the cen tral heating system on and system wa ter in circulation Attention when closing the central heating installation valves ensure that 1 valve re mains open This will prevent pressure in the towel rail from rising excessively The malfunction alert may be removed by turning the heater off and on again In the case of a malfunction alert turn the heater off and wait for the towel rail to cool down Check the device for a pos sible cause referring to the manufacturer problem solving guide and try to resolve it If the heater is still signalling malfunc tion after it is turned on again you should contact your supplier or alternatively the product manufacturer 19 Problem solving Problem The heater is signalling malfunction alert out er diodes shine constant ly while the middle one pulsates Possible cause See description of mal functions alerts Problem solution Follow the steps speci fied in the paragraph re lating to Device malfunc tion alerts Radiator is completely cold diodes shine correctly The thermal fuse has been damaged an electron ics failure The device must be re turned for repair
9. emperature for the towel rail can be set to any of the following values 43 48 52 55 or 60 C A built in temperature sensor protects the towel rail from freezing in situations where the temperature falls below 5 7 C The LED diode next to the on off button will flash recurrently indicat ing that the anti freeze protection is active Heater use The heater is turned on by pressing the on off button The LED diode at the on off button lights up when the heater is on and the regulator maintains the set heating temperature Attention the heater contro panel turns the device on only when radia tor temperature is lower than the set tem perature default temperature of 48 C On reaching the required temperature the heater will turn on recurrently to maintain the set temperature only This function al ows much lower energy consumption than calculations based on the heaters nomi nal heat output might indicate In the up per left part of the control panel there is a TIMER button which can be used to set the automatic switch off time of the device Every subsequent pressing of the buttons 17 18 will light up diodes on the heating time in dicator and allow the user to preset the switch off time of the device to between 1 and 5 hours from the current time After this time the heater will turn off automatically It is useful to know that e Longer pressing of the button will au tomatically
10. f regularly in order to maintain it The basic version of the device is not fit ted with the on off switch on the casing it can be turned on off by plugging it into a mains electricity socket or connect ed permanently to the electricity circuit A shining ring indicates that the device is connected to the electricity circuit Version W of the device not available in the UK is additionally fitted with the on off switch on the plug The construction of the device as well as the physical characteris tics of the heating agent inside the radiator influence the way in which the heat is dis tributed the temperature of the bottom pipes on the radiator especially the two lo cated at the very bottom of the radiator User manual MEG DRY MOA REG 2 REG 3 may be lower than the temperature of the remaining parts of the radiator this is a normal phenomenon Emergency situations Should you discover any abnormalities in the way the device is operating please check if e The device is correctly connected to the installation e The radiator is correctly filled with the appropriate heating agent If the heating element unit is still not work ing correctly it should be uninstalled and returned to the Supplier Seller REG 3 Temperature regulation ring with temperature setting indicators When the device is turned on it heats the radiator up to the set temperature Having reached that temperature the device
11. he mode to which it was set before the dryer mode The dryer is turned on by pressing button also when the device is off The device will start heating at the temperature which was last set This temperature can be mod ified as required while the device is running buttons and If the device was off be fore the dryer mode was been activated then it will turn off automatically when the dryer mode is finished Press button at any time to interrupt the dryer mode User manual MEG DRY MOA REG 2 REG 3 Calibrating the temperature span The standard temperature span of the heating element is 30 60 C It is possible to increase or decrease that span by setting a maximum temperature of between 45 C and 65 C minimum temperature of 30 C stays unchanged This allows the user to achieve a maximum temperature which is higher than the standard or to effectively heat a space with the device during lower surrounding temperatures Example for the temperature regulation span of up to 45 C 30 45 C modification by one step one diode means increase decrease of temperature by 3 75 C while for the temperature regulation span of up to 65 C 30 65 C modification by one step means increase decrease by 8 75 C 45 r A vom k 3 si F oN a A s N wo 2 A vfe g 2 oe In order to modify the temperature span unplug the device and plug it back in while pressing button A single diode will
12. ically This is to prevent the heat ing agent inside the radiator from freezing Activating Anti freeze mode is indicated by winking of the middle diode 15 Problem solving Problem The device is plugged in no diodes are on Possible cause Problem with the connection Solution Check the connection of he power wire the plug and the socket Heating element is not heating outside diodes are winking alternately Temperature sensor has been damaged Disconnect the device completely wait until the radiator cools down and hen re connect it Overheating of device Check that the radia or has been filled with heating agent in the proper manner i e ac cording to the manufactur er s instructions Heating element is heating despite turning it off with the on off button Damaged Electronics Disconnect the device completely wait until the radiator cools down and then re connect it If the problem continues please contact Your local Distributor User manual MEG DRY MOA REG 2 REG 3 DRY TIMER button TIMER indication Indication of heater current working state On off button Functions Heater DRY has 1 fixed temperature set ting default temperature of 48 C and an advanced range of automatic switch off unctions after 1 5 hours This makes the product convenient and user friendly per ect for drying clothing and towels The de ault heating t
13. om the date of production Any claims made will be processed on production of the warranty card and the evidence of purchase The manu facturer has the right to reject any claim on the grounds of failure to present any of the above documents This warranty does not cover any faults that are due to incorrect not in accordance with the manual installation use or disassembly incorrect use of the heating ele ment i e for any purpose that is not User manual MEG DRY MOA REG 2 REG 3 Warranty terms amp conditions specified by the Manufacturer as in tended for this type of product Product being handled by unauthor ized persons Fault s or damages caused by the Client after having purchased and accepted the Product The Central Heating installation should be fitted with lock shield valves ena bling disassembly of the radiator or the heating element and its control head without the necessity of emptying the whole system of the heating agent Any problems or expenses arising from the absence of lock shield valves in your in stallation cannot be used as grounds for any claims against the Supplier or Manufacturer of the device The attached Product Manual is an in tegral element of the Warranty Please read it carefully prior to the installation and use of the Product The Manufacturer is obliged to remove any production fault within 14 working days of receipt
14. on to the presence of children or people with disabilities User manual MEG DRY MOA REG 2 REG 3 6 Ifthe device is used as a clothes and towel dryer ensure that the fabrics drying on it have only been washed in water avoiding contact with any harsh chemicals 7 To ensure the safety of very small children install the electric dryer so that the lowest tube is at least 600 mm above the floor 8 The device should only be installed by a qualified in staller in accordance with the applicable regulations regarding safety and all other regulations 9 All installations to which the device is connected should comply with regulations applicable in the coun try of installation and use 10 Extension leads or electric plug adapters should not be used in order to supply power to the heater 11 The electric installation to which the heater is con nected should have the right current differential and overcurrent relay R C D of 30 mA An Omni pole cut out is required for disconnecting the device on all poles via joints positioned at least 3 mm apart 6 12 13 14 15 The device is suitable for connection in zone 3 as de fined by applicable regulations unless otherwise spec ified by regulations applicable in the country of instal lation and use Attention the device must be installed out of reach of persons in the bathtub shower or pool The device is recommended for use solely as de scribed in the
15. priate supervision Intended use of device The heating element is an electric device intended solely for installation in radiators standalone or connected to the central heating system to serve as space heaters or clothes and towels dryer Technical information Heating element power output should be matched with radiator output for parame ters of 75 65 20 C Model markings power cable type Type of electrical connection Heat outputs available Power supply Insulation class Towel rail connection thread Casing protection class IP Length of heating element 12 User manual MEG DRY MOA REG 2 REG 3 PB Straight cable without plug PW Straight cable with plug SW Spiral cable with plug Y MEG MOA REG 3 DRY Z REG 2 or hard wired connection to electrical system 120 200 300 400 600 800 1000 W 230 V 50 Hz Class G 1 2 IPx4 MEG IPx5 REG 2 REG 3 MOA DRY 120 200 300 400 600 800 1000 w 315 1275 1300 1335 l365 475 565 mm Installation or removal Detailed information demonstrating the different ways of installing or removing a radiator heating element is available from the manufacturer or importer footnotes at the end of the manual Be we list some basic requirements and pri ples which must be followed to ensure term reliable operation of the product see low nci ong Before installation or first use 1 Read the cha
16. pter Safety requirements lInstallation 2 Fit the heating element using the cor rect spanner size amp 22 3 The heating element must be installed at the bottom of the radiator perpen dicular to the radiator pipes while pre serving space for the proper circulation of the heating medium 4 Use a suitable heating medium for fill ing the electric radiator i e water spe cial products based on water and glycol for use in central heating systems or oil which complies with the requirements of the manufacturer of the radiator and heating element 5 Do not switch the heating element on if it is not fully immersed in radiator heat ing medium 6 Make sure an adequate air cushion is present to protect against excessive pres sure build up within the heater always leave one of the radiator valves open 7 When filling the radiator with hot liquid insure that the liquid temperature does not exceed 65 C 13 14 8 Follow the subsequent guidelines when connecting the electrical installation a Brown wire live connection to the circuit L b Blue wire connect to neutral N c Yellow amp green wire earth con nection PE 9 Before filling the radiator with heating medium ensure that the heating ele ment is fitted properly and that it is wa ter tight 10 In central heating installation radiator must be fitted with the valves enabling disconnection of the radiator from the res
17. set the timer to 5 hours or turn off the TIMER function e The button can also be used when the heater is off On pressing the but ton the heater will automatically turn on and set the TIMER to 1 hour e Ifyou want to turn the TIMER off press the button several times or simply turn the heater off and on e TIMER LED diodes will turn off one by one to display the correct remaining drying time The construction of the heater as well as physical characteristics of various heating liquids may cause an uneven heat distribu tion inside the towel rail As a result bot tom pipes of the towel rail may stay cool Such phenomenon is completely normal and is not an indication of heater failure User manual MEG DRY MOA REG 2 REG 3 Modification of radiator heating temperature The default temperature of the heater is 48 C The user can modify the heating tem perature by following these steps 1 Disconnect the device from the elec tricity supply i e unplug the device 2 Press and hold the on off button while reconnecting the heater to the electric ity supply 3 Release the button 4 One of 5 TIMER diodes will start flash ing Select the required temperature value by pressing the button until the corresponding diode starts flashing Temperature values for each diode are shown in the table below K3 52 S50 o AN T y 1 5 Wait for 10 seconds or press the TIMER button in order to confirm your
18. t of the system 11 The temperature of the heating agent in the central heating system must not exceed 82 C Notes prior to removal 1 Before dismantling permanently dis connect the heating element from the mains and ensure that the radiator is not hot 2 Be aware A radiator filled with liquid can be very heavy When moving the radiator ensure that you take the nec essary safety precautions User manual MEG DRY MOA REG 2 REG 3 3 Before disassembly close the appropri ate valves and drain the radiator com pletely to avoid causing any damage pst Product disposal This product should not be disposed of as general waste but should be brought to the appropriate collection point for re cycling of electric and electronic devices This information is provided by the sign on the product user manual and packaging Information on the appropriate point for used devices can be provided by your local authority product distributor or the store from where the product was purchased Thank you for your effort towards protect ing the environment Maintenance e Before performing maintenance always unplug the unit from the mains system e Periodically check the fluid level in the radiator and ensure the heating ele ment is completely submerged e Clean the product with a dry or damp cloth If necessary use a very small amount of detergent ensuring that it contains no solvents or abrasives MEG temperat
19. tended for home use only 11 Fitting and Installation of the device must be carried out in accordance with all local regulations for elec trical safety including installation within permissi ble locations only Observe bathroom electrical zone regulations Safety requirements use 1 The heating element must be fully submerged in the heating liquid during its operation 2 Regularly check the device for damage to ensure it is safe to use 3 Ifthe power cord is damaged the device should not be used Unplug the device and contact the manufactur er or distributor 4 Donotallow flooding into the heating element casing Do not use the heating element in heating systems where the water temperature exceeds 82 C 6 The heating element and radiator can heat up to high temperatures Please be cautious avoid direct con tact with the hot parts of the equipment 7 Do not open the heating element casing 8 In the central heating system always make sure that one valve of the radiator remains open User manua MEG DRY MOA REG 2 REG 3 Ensure that minors aged 8 and above or those with a physical or mental disability are supervised if operat ing the device 10 The device is not a toy Keep it out of the reach of children 11 The device must be disconnected from the mains dur 12 ing cleaning and maintenance Cleaning of the equipment by children under 8 years of age is only permitted under appro
20. ure regulation turn on off button Turning on the device will result in the heating of the radiator up to the set tem perature After reaching the set tempera ure the device will turn off and on regular y in order to maintain the set temperature The construction of the device as well as he physical characteristics of the heating agent inside the radiator influence the way in which the heat is distributed the tem perature of the bottom pipes on the radia or especially the two located at the very bottom of the radiator may be lower than he temperature of the remaining parts of he radiator this is normal Temperature increase In order to increase the temperature of the radiator press once or several times as required the right number of diodes will start blinking The last blinking diode indi cates the set temperature whilst the last Temperature decrease In order to decrease the temperature of the radiator press once or several times as required the right number of diodes will start blinking The last diode that which shines constantly indicates the set tem perature whilst the last blinking diode in dicates the current temperature The fol lowing diodes will start fading on reaching subsequent temperature levels Anti freeze function anti freeze protection When the device is off and the tempera ture around temperature sensor drops down below 6 C the device will switch on automat
21. will turn on and off regularly in order to main tain it The construction of the device as well as the physical characteristics of the heating agent inside the radiator influence the way in which the heat is distributed the tem perature of the bottom pipes on the ra diator especially the two located at the very bottom of the radiator may be low er than the temperature of the remain ing parts of the radiator this is a normal phenomenon Emergency situations Should you discover any abnormalities in the way the device is operating please check if e The device is correctly connected to the installation e The radiator is correctly filled with the appropriate heating agent If the heating element unit is still not work ing correctly it should be uninstalled and returned to the supplier 25 26 The subject of this warranty is an elec tric heating element with control head The product name and characteristics are specified on the packaging By accepting the device on purchase the Client confirms that the product is of full value The Client should imme diately inform the Seller of any discov ered faults otherwise it will be un derstood that the Product was faultless at the time of purchase This refers es pecially to any faults or damages of the control panel case The Warranty for period for the Product is 24 months from the date of purchase but no longer than 36 months fr
Download Pdf Manuals
Related Search