User Manual - Plasticare
Contents
1. htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Additives ONSISTENCY Unthickened mixture UP C HARACTERISTICS Drips off vertical surfaces Coating wetting out before bonding applying fiberglass graphite and other fabrics C CONSISTENCY Slightly thickened HARACTERISTICS Sags down vertical surfaces SYR C CATS C Laminating bonding flat panels with large surface areas injecting with a syringe ONSISTENCY Moderately thickened CHARACTERISTICS Clings to vertical surfaces peaks fall over General bonding filleting hardware bonding CHARACTERISTICS Clings to vertical surfaces peaks stand up Gap filling filleting fairing bonding uneven surfaces Page 6 of 24 Additives are used to give epoxy additional physical properties when used as a coating Although additives are blended with mixed epoxy in the same two step process as fillers they are not designed to thicken the epoxy Refer to Additive descriptions Follow the mixing instructions on the individual additive containers Clean up Contain large spills with sand clay or other inert absorbent material Use a scraper to contain small spills and collect as much material as possible Follow up with absorbent towels Uncontaminated resin or hardener may be reclaimed for use DO NOT use sawdust or other fine cellulose materials to absorb hardeners DO NOT dispose of hardener in trash con2. Applying woven cloth amp tape Fiberglass cloth is applied to surfaces to provide reinforcement and or abrasion resistance or in the case of Douglas Fir plywood to prevent grain checking It is usually applied after fairing and shaping are completed and before the final coating operation It is also applied in multiple layers laminated and in combination with other materials to build composite parts Fiberglass cloth may be applied to surfaces by either of two methods The dry method refers to applying the cloth over a dry surface The wet method refers to applying the cloth to an epoxy coated surface often after the wet out coat becomes tacky which helps it cling to vertical or overhead surfaces Since this method makes it more difficult to position the cloth the dry method is the preferred method especially with thinner cloth Dry method 1 Prepare the surface as you would for bonding 2 Position the cloth over the surface and cut it several inches larger on all sides If htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 18 of 24 the surface area you are covering is larger than the cloth size allow multiple pieces to overlap by approximately two inches On sloped or vertical surfaces hold the cloth in place with masking or duct tape or with staples 3 Mix a small quantity of epoxy three or four pumps each of resin and hardener 4 Pour a small pool of resin nardener near the
3. The thicker the mixture the easier it will be to sand when cured 4 Trowel on the thickened epoxy mixture with a plastic squeegee working it into all voids and depressions Smooth the mixture to the desired shape leaving the mixture slightly higher than the surrounding area Figure 22 Remove any excess thickened epoxy before it cures If the voids you are filling are over 1 2 deep apply the mixture in several applications or use 206 Slow Hardener or 209 Tropical Hardener depending on ambient temperature Note On vertical and overhead surfaces allow the wet out coat to gel before applying fairing compound The fairing compound may sag or slide off the fresh wet out coat Apply the fairing compound while the wet out is still in the gel stage Figure 23 Sand cured fairing compound to desired contour 5 Allow the final thickened epoxy application to cure thoroughly 6 Sand the fairing material to blend with the surrounding contour Figure 23 Begin with 50 grit sandpaper if you have a lot of fairing material to remove Use 80 grit paper on the appropriate sanding block when you are close to the final contour CAUTION Don t forget your dust mask Remove the sanding dust and fill any remaining voids following the same procedure 7 Apply several coats of resin hardener to the area with a disposable brush or roller after you are satisfied with the fairness Allow the final coat to cure thoroughly before final sanding and finishing
4. htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 11 of 24 enough of the mixture to one of the surfaces so that a small amount will squeeze out when the surfaces are joined together with a force equivalent to a firm hand grip Figure 10 Thickened epoxy can be applied immediately over the wet out surface or any time before the wet out reaches its final cure For most small bonding operations add the filler to the resin nardener mixture remaining in the batch that was used for the wet out Mix enough resin hardener for both steps Add the filler quickly after the surface is wet out and allow for a shorter working life of the mixture 3 Clamp components Attach clamps as necessary to hold the components in place Use just enough clamping pressure to squeeze a small amount of the epoxy mixture from the joint indicating that the epoxy is making good contact with both mating surfaces Figure 11 Avoid using too much clamping pressure which can squeeze all of the epoxy mixture out of the joint Figure 12 Figure 11 Clamp components in place Remove or shape excess epoxy before the epoxy gels hat squeezes out of the joint 4 Remove or shape excess adhesive that squeezes out of the joint as soon as the joint is secured with clamps A wooden mixing stick with one end sanded to a chisel edge is an ideal tool for removing the excess Figure 12 Single step bonding Single step bonding is ap
5. published by Gougeon Brothers for detailed information on patching gelcoat over an epoxy repair Follow all instructions from the coating systems manufacturer It is a good idea to make a test panel to evaluate the degree of surface preparation required and the compatibility and handling characteristics of the finish system For detailed instruction on the application of these techniques in repair and construction refer to specific WEST SYSTEM instructional publications and videos For complete descriptions of all WEST SYSTEM products including selection and coverage guides go to the Product Guide To help you identify and prevent potential problems associated with using epoxy go to the Problem Solver For complete information on the hazards associated with epoxy and the precautions you can take to avoid them go to Health amp Safety To see how these techniques have been put to use in a wide range of repair and construction applications go to the Projects pages Tips htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 24 of 24 Thinning epoxy There are epoxy based products specifically designed to penetrate and reinforce rotted wood These products basically an epoxy thinned with solvents do a good job of penetrating wood But the solvents compromise the strength and moisture barrier properties of the epoxy WEST SYSTEM epoxy can be thinned with solvents for greater pene
6. Apply enough epoxy to saturate the fabric and the wood below After several minutes lay on additional epoxy to dry white areas If epoxy appears milky due to high humidity or over working warm the surface by passing a heat gun or hair dryer over the surface Use low heat to avoid out gassing Be sure to use 207 Hardener for clear finishes Epoxy barrier coating The object of barrier coating is to build up an epoxy coating that provides an effective moisture barrier and a smooth base for final finishing Apply a minimum of two coats of WEST SYSTEM epoxy for an effective moisture barrier Apply three coats if sanding is to be done Moisture protection will increase with additional coats up to six coats or about a 20 mil thickness Additives or pigments should not be added to the first coat Mixing thinners with WEST SYSTEM epoxy is not recommended Disposable thin urethane foam rollers such as WEST SYSTEM 800 Roller Covers allow you greater control over film thickness are less likely to cause the epoxy to exotherm and leave less stipple than thicker roller covers Cut the covers into narrower widths to reach difficult areas or for long narrow surfaces like stringers Complete all fairing and cloth application before beginning the final coating Allow the temperature of porous surfaces to stabilize before coating Otherwise as the material warms up air within the porous material may expand and pass from the material out gassing throug
7. Strict formula or measuring involved use your eye to judge what consistency will work best Figure 5 gives you a general guide to the differences between neat unthickened epoxy and the three consistencies referred to in this manual Always add fillers in a two step process 1 Mix the desired quantity of resin and hardener thoroughly before adding fillers Begin with a small batch allow room for the filler 2 Blend in small handfuls or scoops of the appropriate filler until the desired consistency is reached Figure 4 Figure 4 Stir in small handtuls at filler until the desired cond stancy is reached For maximum strength add only enough filler to completely bridge gaps between surface without sagging or running out of the joint or gap A small amount should squeeze out of joints when clamped For thick mixtures don t fill the mixing cup more than 1 3 full of epoxy before adding filler When making fairing compounds stir in as much 407 or 410 as you can blend in smoothly for easy sanding the thicker the better Be sure all of the filler is thoroughly blended before the mixture is applied Spread the mixture into a thinner layer either around the inside of the mixing cup or onto a flat non porous surface or palette to extend its working life Epoxy can be thickened to the ideal consistency needed for a particular job The procedures in this manual refer to four common consistencies syrup catsup mayonnaise and peanut butter
8. mixing are essential for a proper cure Whether the resin hardener mixture is applied as a coating or modified with fillers or additives observing the following procedures will assure a controlled and thorough chemical transition to a high strength epoxy solid Dispensing Dispense the proper proportions of resin and hardener into a clean plastic metal or wax free paper container Figure 2 Don t use glass or foam containers because of the potential danger from exothermic heat build up Sf Figure 2 Dispense the proper proportion of resin and hardener htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 4 of 24 DO NOT attempt to adjust the epoxy cure time by altering the mix ratio An accurate ratio is essential for a proper cure and full development of physical properties e Dispensing with Mini pumps Most problems related to curing of the epoxy can be traced to the wrong ratio of resin and hardener To simplify metering we recommend using calibrated WEST SYSTEM Mini Pumps to dispense the resin and hardener Mini Pumps are calibrated to deliver the proper working ratio of resin to hardener Pump one full pump stroke of resin for each one full 1 q Correct pump stroke of hardener Depress each pump head Se Ratio fully and allow the head to come completely back to the top before beginning the next stroke Partial strokes will give the wrong ratio Read the pump instructions befo
9. of curing epoxy is determined by the ambient temperature plus the exothermic heat generated by its cure Ambient temperature is the temperature of the air or material in contact with the epoxy Air temperature is most often the ambient temperature unless the epoxy is applied to a surface with a different temperature Generally epoxy cures faster when the air temperature is warmer Exothermic heat is produced by the chemical reaction that cures epoxy The amount of heat produced depends on the thickness or exposed surface area of mixed epoxy In a thicker mass more heat is retained causing a faster reaction and more heat The mixing container s shape and the mixed quantity have a great affect on this exothermic reaction A contained mass of curing epoxy 8 fl oz or more in a plastic mixing cup can quickly generate enough heat to melt the cup and burn your skin However if the same quantity is spread into a thin layer exothermic htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 3 of 24 heat is dissipated and the epoxy s cure time is determined by the ambient temperature The thinner the layer of curing epoxy the less it is affected by exothermic heat and the slower it cures Controlling cure time In warm conditions use a slower hardener if possible Mix smaller batches that can be used up quickly or pour the epoxy mixture into a container with greater surface area a roller pan for exampl
10. wood surfaces with epoxy it s a good idea to brush the wet epoxy in the direction of the grain with a wire brush to improve adhesion Allow solvents to dry before recoating Removing fiberglass cloth applied with epoxy Use a heat gun to heat and soften the epoxy Start in a small area a near a corner or edge Apply heat until you can slip a putty knife or chisel under the cloth about 200 F Grab the edge with a pair of pliers and pull up on the cloth while heating just ahead of the separation On large areas use a utility knife to score the glass and remove in narrower strips Resulting surface texture may be coated or remaining epoxy may be removed as follows Removing cured epoxy coating Use a heat gun to soften the epoxy 200 F Heat a small area and use a paint or cabinet scraper to remove the bulk of the coating Sand the surface to remove the remaining material Provide ventilation when heating epoxy MYEGT Copyright 2005 West System Inc All rights reserved SYSTEM This page is maintained by West System Inc Last Modified on October 31 2005 WEST SYSTEM and EPOXYWORKS are registered trademarks of West System Inc Bay City Michigan USA htto www westsystem com webpages userinfo manual 10 9 2007
11. Dry with paper towels htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 22 of 24 3 Sand to a smooth finish Figure 32 If there are runs or sags begin sanding with 80 grit paper to remove the highest areas Sand until the surface feels and looks fair Complete sanding with the appropriate grit for the type of coating to be applied check coating instructions Paint adhesion relies on the mechanical grip of the paint keying into the sanding scratches in the epoxy s surface If a high build or filling primer is to be applied 80 100 grit is usually sufficient 120 180 grit may be adequate for primers and high solids coatings Finishing with 220 400 grit paper will result in a high gloss finish for most paints or varnishes Grits finer than this may not provide enough tooth for good adhesion Many people prefer wet sanding because it reduces sanding dust and it will allow you to skip Step 2 4 After you are satisfied with the texture and fairness of the surface rinse the surface with fresh water Rinse water should sheet evenly without beading or fisheyeing If rinse water beads up a sign of contamination wipe the area with solvent and dry with a paper towel then wet sand again until beading is eliminated Proceed with your final coating after the surface has dried thoroughly To reduce the possibility of contamination it is a good idea to begin coating within 24 hours of the final sanding Follow al
12. WEST SYSTEM User Manual Page 1 of 24 User Manual This User Manual is the primary guide to the handling and basic techniques of epoxy use It describes how to dispense mix and modify WEST SYSTEM epoxy for the basic coating filling and bonding techniques used in most repair and construction procedures These procedures are described in detail in WEST SYSTEM instructional publications and videos For complete descriptions of all WEST SYSTEM products including selection and coverage guides go to the Product Guide e To help you identify and prevent potential problems associated with using epoxy go to the Problem Solver e For complete information on the hazards associated with epoxy and the precautions you can take to avoid them go to Health amp Safety e To see how these techniques have been put to use in a wide range of repair and construction applications go to the Projects pages HANDLING EPOXY Epoxy chemistry Epoxy s cure stages Mixing epoxy resin and hardener begins a chemical reaction that transforms the combined liquid ingredients to a solid The time it takes for this transformation is the cure time As it cures the epoxy passes from the liquid state through a gel state before it reaches a solid state Figure 1 As it cures mixed epxoy pass from a liquid state through a gel state to a solid state 5 i r a Wu Cure time after mixing Figure d 1 Liquid Open time Open time a
13. ard especially when sprayed Bottom paints are available in a variety of formulations Most bottom paint systems are compatible with epoxy and can be applied directly over a prepared epoxy barrier coat If you are unsure of compatibility or have curing or adhesion problems with a specific bottom paint use only a primer recommended for that bottom paint over the barrier coat Follow the recommendations given for preparation of fiberglass surfaces Other paints including marine LP s and primers are not recommended for use below the waterline Primers are usually not needed to help a paint film bond to epoxy although interfacing primers may be required with some specialized bottom paints and high build primers are useful for hiding scratches or flaws in the substrate If the instructions on your paint or varnish recommend a specially primed surface follow the recommendations given for fiberglass preparation Self etching primers do not work well on an epoxy coating because of epoxy s chemical resistance Polyester gelcoat is a pigmented version of the resin used to build fiberglass boats and other products Gelcoat is sprayed into a mold before the glass fabric and resin are applied to provide a smooth pre finished surface when the part is removed from the mold It is not often used as a post production finish coating but it can be applied over epoxy and is useful in some repair situations Refer to 002 550 Fiberglass Boat Repair and Maintenance
14. bility to mechanically key into the surface That is why the following three steps of surface preparation are a critical part of any secondary bonding operation For good adhesion bonding surfaces should be 1 Clean Bonding surfaces must be free of any contaminants such as grease oil wax or mold release Clean contaminated surfaces with lacquer thinner acetone or other appropriate solvent Wipe the surface with paper towels before the solvent dries Clean surfaces before sanding to avoid sanding the contaminant into the surface Follow all safety precautions when working with solvents Figure 6 Figure amp Clean the surface Use a solvent If necessary to remove all contaminates 2 Dry All bonding surfaces must be as dry as possible for good adhesion lf necessary accelerate drying by warming the bonding surface with a hot air gun hair dryer or heat lamp Use fans to move the air in confined or enclosed spaces Watch for condensation when working outdoors or whenever the temperature of the work environment changes Figure 7 htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 9 of 24 Figure T ODrythe surface Allow the surface to dry thoroughly or use heat ora tan to speed drying 3 Sanded Sand smooth non porous surfaces thoroughly abrade the surface 80 grit aluminum oxide paper will provide a good texture for the epoxy to key into Be sure the surface to be bonded is so
15. center of the cloth 5 Spread the epoxy over the cloth surface with a plastic spreader working the epoxy gently trom the pool into the dry areas Figure 24 Use a foam roller or brush to wet out fabric on vertical surfaces Properly wet out fabric is transparent White areas indicate dry fabric If you are applying the cloth over a porous surface be sure to leave enough epoxy to be absorbed by both the cloth and the surface below it Try to limit the amount of squeegeeing you do The more you work the wet surface the more minute air bubbles are placed in suspension in the epoxy This is especially important if you plan to use a clear finish You may use a roller or brush to apply epoxy to horizontal as well as vertical surfaces Smooth wrinkles and position the cloth as you work your way to the edges Check for dry areas especially over porous surfaces and re wet them as necessary before proceeding to the next step If you have to cut a pleat or notch in the cloth to lay it flat on a compound curve or corner make the cut with a pair of sharp scissors and overlap the edges for now Figure 26 z gu gm Pa ifr ff Gp Saa spread the epoxy ower the cloth GUBEQEE GMa GXCESS Epoxy surface with a plastic spreader before it begins to gel 6 Squeegee away excess epoxy before the first batch begins to gel Figure 25 Slowly drag the squeegee over the fabric at a low almost flat angle using even pressured overlapping strokes Use
16. e The result should be a near perfect butt joint eliminating double cloth thickness A lapped joint is stronger than a butt joint so if appearance is not important you may want to leave the overlap and fair in the unevenness after coating 8 Coat the surface to fill the weave before the wet out reaches Its final cure stage Figure 29 Follow the procedures for final coating in the next section It will take two or three coats to completely fill the weave of the cloth and to allow for a final sanding that will not affect the cloth Wet method An alternative is to apply the fabric or tape to a surface coated with wet epoxy As mentioned this is not the preferred method especially with large pieces of cloth because of the difficulty removing wrinkles or adjusting the position of the cloth as it is being wet out However you may come across situations when this method may be useful or necessary 1 Prepare the surface for bonding Pre fit and trim the cloth to size Roll the cloth neatly so that it may be conveniently rolled back into position later 2 Roll a heavy coat of epoxy on the surface 3 Unroll the glass cloth over the wet epoxy and position it Surface tension will hold most cloth in position If you are applying the cloth vertically or overhead you may want to thicken the epoxy slightly with filler then wait until it becomes sticky Work out wrinkles by lifting the edge of the cloth and smoothing from the center with you
17. e thereby allowing exothermic heat to dissipate and extending open time The sooner the mixture is transferred or applied after thorough mixing the more of the mixture s useful open time will be available for coating lay up or assembly In cool conditions use a faster hardener or use supplemental heat to raise the epoxy temperature above the hardener s minimum recommended application temperature Use a hot air gun heat lamp or other heat source to warm the resin and hardener before mixing or after the epoxy is applied At room temperature supplemental heat is useful when a quicker cure is desired For detailed information on working with epoxy at low temperatures refer to 002 915 Cold Temperature Bonding and Coating with Epoxy CAUTION Heating epoxy that has not gelled will lower its viscosity allowing the epoxy to run or sag more easily on vertical surfaces In addition heating epoxy applied to a porous substrate softwood or low density core material may cause the substrate to out gas and form bubbles in the epoxy coating To avoid out gassing wait until the epoxy coating has gelled before warming it Never heat mixed epoxy in a liquid state over 120 F 49 C Regardless of what steps are taken to control the cure time thorough planning of the application and assembly will allow you to make maximum use of epoxy s open time and cure time Dispensing and mixing Careful measuring of epoxy resin and hardener and thorough
18. e tool and leaving a smooth cove shaped fillet bordered on each side by a clean margin Some excess filleting material will remain outside of the margin Figure 13 Use the excess material to re fill any voids Smooth the fillet until you are satisfied with its appearance A mixing stick will leave a fillet with about a 3 8 radius For larger fillets an 808 Plastic Squeegee cut to shape or bent to the desired radius works well Apply additional thickened epoxy to fill voids or make larger fillets Apply the mixture along the joint line with the rounded mixing stick using enough mixture to create the desired size of fillet For longer or multiple fillets empty caulking gun cartridges or disposable cake decorating bags can be used Cut the plastic tip to lay a bead of thickened epoxy large enough for the desired fillet size Heavy duty sealable food storage bags with one corner cut off may also be used Figure 13 Figure 14 Clean Up the excess epoxy Wet out a standard pilot hole outside of the fillet margin and install the fastener 3 Clean up the remaining excess material outside of the margin by using a sharpened mixing stick or a putty knife Figure 14 Fiberglass cloth or tape may be applied over the fillet area before the fillet has cured or after the fillet is cured and sanded 4 Sand smooth with 80 grit sandpaper after the fillet has fully cured Wipe the surface clean of any dust and apply several coats of resin hardene
19. emoves the oil at the surface and allows epoxy to penetrate Be sure solvent has evaporated before coating Porous woods No special preparation needed If surface is burnished possibly by dull planer or saw blades sand with 80 grit paper to open pores Remove dust htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 10 of 24 Steel lead Remove contamination sand or grind to bright metal coat with epoxy then sand fresh epoxy into surface Re coat or bond after first coat gels Aluminum Sand and prepare with 860 Aluminum Etch Kit Polyester fiberglass Clean contamination with a silicone and wax remover such as DuPont Prep Sol 3919S Sand with 80 grit paper to a dull finish Plastic Adhesion varies If a plastic is impervious to solvents such as acetone epoxy generally will not bond to it Soft flexible plastics such as polyethylene polypropylene nylon Plexiglas and polycarbonate fall into this category Hard rigid plastics such as PVC ABS and styrene provide better adhesion with good surface preparation and adequate bonding area After sanding flame oxidizing by quickly passing propane torch over the surface without melting the plastic can improve bonding in some plastics It s a good idea to conduct an adhesion test on a plastic that you are uncertain about Bonding gluing This section refers to two types of bonding Two step bonding is the preferred method for most situation
20. enough pressure to remove excess epoxy that would allow the cloth to float off the surface but not enough pressure to create dry spots Excess epoxy appears as a shiny area while a properly wet out surface appears evenly transparent with a smooth cloth texture Later coats of epoxy will fill the weave of the cloth 7 Trim the excess Figure 26 and overlapped cloth Figure 27 after the epoxy has reached its initial cure The cloth will cut easily with a sharp utility knife Trim overlapped cloth if desired as follows Figure 26 ory ler a i ag a op as Fis a SE vg a Mi 7 Trim excess doth atter the Trim overlapped cloth ater epoxy gels he epoxy gels htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 19 of 24 Place a metal straightedge on top of and midway between the two overlapped edges b Cut through both layers of cloth with a sharp utility knife c Remove the top most trimming and then lift the opposite cut edge to remove the overlapped trimming Figure 28 d Re wet the underside of the raised edge with epoxy and smooth into place Figure 29 Figure 2 ene a ni s l at cf Le ys ee i EPEA Ter a Fe F aa n a of 5 Pes r i ay z 4 gt a F F l e Se a a m mF r i Remove the topmost trimming Coal the surface to fill the weave lift the opposite cut edge to before the wet out reaches remove the ovenapped timming its final cure sag
21. h the coating and leave bubbles in the cured coating 1 Prepare the surface for 2 Mix only as much resin hardener as you can apply during the open time of the mixture Pour the mixture into a roller pan as soon as it is mixed thoroughly 3 Load the roller with a moderate amount of the epoxy mixture Roll the excess out on the ramp part of the roller pan to get a uniform coating on the roller 4 Roll lightly and randomly over an area approximately 2 ft x 2 ft to transfer the epoxy evenly over the area Figure 30 5 As the roller dries out increase pressure enough to spread the epoxy into a thin even film Increase the coverage area if necessary to spread the film more thinly and evenly The thinner the film the easier it is to keep it even and avoid runs or Sags in each coat 6 Finish the area with long light even strokes to reduce roller marks Overlap the previously coated area to blend both areas together 7 Coat as many of these small working areas as you can with each batch If a batch begins to thicken before it can be applied discard it and mix a fresh smaller htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 21 of 24 batch Figure 30 Figure 31 Roll lighth and randomly over a Tip off the coating b dragging a amall area Spread the epoxy foam roller brush lightly over Into thin even film the fresh epoxy 8 Tip off the coating by dragging a foam roller brush lightly ove
22. ighten the fasteners until a he fastener threads with amall amount of epoxy thickened epoxy squeezes trom the joint 1 Prepare the mounting surface and the hardware base for good adhesion 2 Wet out the oversized hole with epoxy Allow the epoxy to soak into the exposed end grain of the wood as with faster bonding 3 Coat the bottom contact surface of the hardware with unthickened epoxy Wire brush or sand the wet epoxy into the surface with 50 grit sandpaper 4 Inject a non sagging epoxy 404 or 406 mixture into the hole Use enough mixture so there are no voids in the hole after inserting the fastener Coat the bottom of the hardware and the fastener threads with thickened epoxy Figure 17 5 Place the hardware in position Insert and tighten fasteners until a small amount of the mixture squeezes out of the joint Figure 18 6 Remove excess epoxy or shape into a fillet Allow the epoxy to cure at least 24 hours before applying load to the hardware Allow more time in cool weather Casting a base Use the thickened epoxy to cast a base under the hardware when mounting hardware to a curved or uneven surface or mounting hardware at an angle to the Surface Figure 19 a ry C 1 a oy a EL e ay T i E e B hR Suppor the base in position with blocking apply enough thickened epoxy to fill void 1 Prepare the fasteners holes substrate and base as described above 2 Bond small blocks to the substrate
23. irection of the grain with a wire brush to improve adhesion Allow solvents to dry before recoating Removing fiberglass cloth applied with epoxy Use a heat gun to heat and soften the epoxy Start in a small area a near a corner or edge Apply heat until you can slip a putty knife or chisel under the cloth about 200 F Grab the edge with a pair of pliers and pull up on the cloth while heating just ahead of the separation On large areas use a utility knife to score the glass htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 8 of 24 and remove in narrower strips Resulting surface texture may be coated or remaining epoxy may be removed as follows Removing cured epoxy coating Use a heat gun to soften the epoxy 200 F Heat a small area and use a paint or cabinet scraper to remove the bulk of the coating Sand the surface to remove the remaining material Provide ventilation when heating epoxy BASIC TECHNIQUES The following basic techniques are common to most repair or building projects regardless of the type of structure or material you are working with Surface preparation Whether you are bonding fairing or applying fabrics the success of the application depends not only on the strength of the epoxy but also on how well the epoxy adheres to the surface to which it is being applied Unless you are bonding to partially cured epoxy the strength of the bond relies on the epoxy s a
24. l of the instructions from the coating system s manufacturer A good trick used by professionals is to make a test panel to evaluate the degree of surface preparation required and the compatibility of the finish system Finish coatings The function of a finish coating like paint or varnish over an epoxy barrier coat is to decorate the surface and protect the epoxy from sunlight In doing so the finish coating extends the life of the epoxy moisture barrier which in turn provides a stable base that extends the life of the finish coating Together the two forma protective system far more durable than either coating by itself Protection from sunlight is a primary consideration in the selection of a finish coating Long term UV ultraviolet protection of the barrier coat depends on how well the finish coating itself resists UV and keeps its pigments or its shield of UV filters on the surface of the epoxy barrier coat A high gloss finish reflects a higher proportion of the light hitting the surface than a dull surface All other thing being equal a white especially a glossy white coating will last the longest Most types of coatings are compatible with epoxy Thoroughly cured epoxy is an almost completely inert hard plastic This means most paint solvents will not soften swell or react with it However it is still a good idea to build a test panel to assure coating compatibility Coating types Latex paints are compatible with epoxy and
25. les or screws such as a foam or honeycomb core material Vacuum bagging is the ideal clamping method for laminating a wide range of materials Through the use of a vacuum pump and plastic sheeting the atmosphere is used to apply perfectly even clamping pressure over all areas of a panel regardless of the size shape or number of layers NOTES Primary Secondary Bonding Primary bonding relies on the chemical linking of adhesive layers such as the wet lay up of fiberglass laminate in a mold All the layers of adhesive cure together in a single fused layer Epoxy applied over partially cured epoxy will chemically link with it and is a primary bond The ability to chemically link diminishes as the epoxy cures and it becomes a secondary bond Secondary bonding relies on the mechanical linking of an adhesive to a material or cured epoxy surface The adhesive must key into pores or scratches in the Surface a microscopic version of a dovetail joint Proper surface preparation provides a texture that will help lock the cured epoxy to the surface Clamping Any method of clamping is suitable as long as the parts to be joined are held so that movement will not occur Common methods include spring clamps C clamps and adjustable bar clamps heavy rubber bands cut from inner tubes nylon reinforced packaging tape applying weights and vacuum bagging When placing clamps near epoxy covered areas cover clamp pads with duct tape or use polyethylene
26. lid Remove any flaking chalking blistering or old coating before sanding Remove all dust after sanding Figure 8 sand non porous SUPface Provide a texture for epoxy ta key into Special preparation for various materials Cured epoxy Amine blush can appear as a wax like film on cured epoxy surfaces It is a by product of the curing process and may be more noticeable in cool moist conditions Amine blush can clog sandpaper and inhibit subsequent bonding but it can easily be removed It s a good idea to assume it has formed on any cured epoxy surface To remove the blush wash the surface with clean water not solvent and an abrasive pad such as Scotch brite 7447 General Purpose Hand Pads Dry the surface with paper towels to remove the dissolved blush before it dries on the surface Sand any remaining glossy areas with 80 grit sandpaper Wet sanding will also remove the amine blush If a release fabric is applied over the surface of fresh epoxy amine blush will be removed when the release fabric is peeled from the cured epoxy and no additional sanding is required Epoxy surfaces that have not fully cured may be bonded to or coated with epoxy without washing or sanding Before applying coatings other than epoxy paints bottom paints varnishes gelcoats etc allow epoxy surfaces to cure fully then wash and sand Hardwoods Sand with 80 grit paper Teak oily woods Wipe with acetone 15 minutes before coating Solvent r
27. lso working time or wet lay up time is the portion of the cure time after mixing that the resin hardener mixture remains a liquid and is workable and suitable for application All assembly and clamping should take place during the open time to assure a dependable bond 2 Gel Initial cure The mixture passes into an initial cure phase also called the green stage when it begins to gel or kick off The epoxy is no longer workable and will no longer feel tacky During this do not disturb stage it progresses from a soft gel consistency to the firmness of hard rubber You will be able to dent it with your thumbnail htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 2 of 24 Because the mixture is only partially cured a new application of epoxy will still chemically link with it so the surface may still be bonded to or recoated without Special preparation However this ability diminishes as the mixture approaches final cure 3 Solid Final cure The epoxy mixture has cured to a solid state and can be dry sanded and shaped You should not be able to dent it with your thumbnail At this point the epoxy has reached about 90 of its ultimate strength so clamps can be removed It will continue to cure over the next several days at room temperature A new application of epoxy will no longer chemically link to it so the surface of the epoxy must be properly prepared and sanded before recoating to achieve a go
28. od mechanical secondary bond See Surface Preparation Understanding cure time Open time and cure time govern much of the activity of building and repairing with epoxy Open time dictates the time available for mixing application smoothing shaping assembly and clamping Cure time dictates how long you must wait before removing clamps or before you can sand or go on to the next step in the project Two factors determine an epoxy mixture s open time and overall cure time hardener cure speed and epoxy temperature Hardener speed Each hardener has an ideal temperature cure range At any given temperature each resin hardener combination will go through the same cure stages but at different rates Select the hardener that gives you adequate working time for the job you are doing at the temperature and conditions you are working under The product guide and container labels describe hardener pot lives and cure times Pot life is a term used to compare the cure speeds of different hardeners It is the amount of time a specific mass of mixed resin and hardener remains a liquid ata specific temperature A 100g mass mixture in a standard container at 72 F Because pot life is a measure of the cure speed of a specific contained mass volume of epoxy rather than a thin film a hardener s pot life is much shorter than its open time Epoxy temperature The warmer the temperature of curing epoxy the faster it cures Figure 1 The temperature
29. plying the thickened epoxy directly to both bonding surfaces without first wetting out the surfaces with neat resin hardener We recommend that you thicken the epoxy no more than is necessary to bridge gaps in the joint the thinner the mixture the more it can penetrate the surface and that you do not use this method for highly loaded joints or for bonding end grain or other porous surfaces Laminating The term laminating refers to the process of bonding numbers of relatively thin layers like plywood veneers fabrics or core material to create a composite A composite may be any number of layers of the same material or combinations of different materials Methods of epoxy application and clamping will differ depending on what you are laminating Because of large surface areas and limitations of wet lay up time roller application is the most common method for applying epoxy A faster method for large surfaces is to simply pour the resin hardener mixture onto the middle of the panel and spread the mixture evenly over the surface with a plastic spreader Apply thickened mixtures with an 809 Notched Spreader Using staples or screws is the most common method of clamping when you htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 12 of 24 laminate a solid material to a solid substrate An even distribution of weights will work when you are laminating a solid material to a base that will not hold stap
30. r gloved hand or a squeegee 4 Apply a second coat of epoxy with a foam roller Apply enough epoxy to thoroughly wet out the cloth 5 Remove the excess epoxy with a squeegee using long overlapping strokes The cloth should appear consistently transparent with a smooth cloth texture 6 Follow steps 7 8 and 9 under the dry method to finish the procedure Any remaining irregularities or transitions between cloth and substrate can be faired by using an epoxy filler fairing compound if the surface is to be painted Any additional fairing done after the final coating should receive several additional coats htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 20 of 24 over the faired area Note A third alternative for more experienced users is a variation of both methods Apply the fabric after a wet out coat has reached an initial cure Follow the first three steps of the Wet Method but wait until the epoxy cures dry to the touch before positioning the fabric and continuing with Step 3 of the Dry Method Apply the fabric before the first coat reaches its final cure phase NOTE Clear Wood Finishes stripper canoes etc An alternative wet out method is to lay the epoxy onto the fabric with a short bristled bush Dip the brush in the epoxy and lay the epoxy on the surface with a light even stroke Don t force the epoxy into the cloth which may trap air in the fabric and show through the clear finish
31. r over the entire fillet area before final finishing Bonding fasteners and hardware Installing screws and other threaded fasteners with WEST SYSTEM epoxy dramatically improves load carrying capacity by spreading the fastener s load into a greater area of the substrate There are several methods or levels of hardware bonding depending on the loads on the hardware Basic fastener bonding For improved pullout strength and waterproof connections the easiest method is to simply wet out stripped fastener holes and new pilot holes before installing the screws Epoxy penetrates the fiber around the hole effectively increasing the fastener diameter Epoxy also provides a stronger interface with the fastener threads than wood fiber and keeps out water htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 14 of 24 Drill oversized holes to increase the exposed substrate area and the amount of epoxy around the fastener 1 Wet out a standard size pilot hole Work the mixture well into the hole with a pipe cleaner or syringe Figure 15 Thicken a second coat of epoxy as necessary for stripped or oversized holes 2 Insert the fastener in the hole and allow the epoxy to cure Advanced fastener bonding For greater strength and stability drill oversized holes to increase the exposed substrate area and the amount of epoxy around the fastener If the fastener hardware can be clamped by other means the ove
32. r the fresh epoxy in long even overlapping strokes after each batch is applied Use enough pressure to smooth the stipple but not enough to remove any of the coating Figure 31 Alternate the direction in which each coat is tipped off 1st coat vertical 2nd coat horizontal 3rd coat vertical etc A WEST SYSTEM 800 Roller Cover can be cut into segments to make a tipping brush Recoating Apply second and subsequent coats of epoxy following the same procedures Make sure the previous coat has cured firmly enough to support the weight of the next coat To avoid sanding between coats apply all of the coats in the same day See Special preparation Cured epoxy After the final coat has cured overnight wash and sand it to prepare for the final finish Final surface preparation Proper finishing techniques will not only add beauty to your efforts but will also protect your work from ultraviolet light which will break down epoxy over time The most common methods of finishing are painting or varnishing These coating systems protect the epoxy from ultraviolet light and require proper preparation of the surface before application Preparation for the final finish is just as important as it is for recoating with epoxy The surface must first be clean dry and sanded Figure 32 Sand ta a smooth nish 1 Allow the final epoxy coat to cure thoroughly 2 Wash the surface with a Scotch brite pad and water to remove amine blush
33. ratures lf you are going to be using the mixture for coating quickly pour it into a roller pan to extend the open time htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 5 of 24 WARNING Curing epoxy generates heat When contained a large mass of curing epoxy has a very short pot life and can generate enough heat to melt plastic and foam burn your skin and ignite combustible materials For this reason do not use foam or glass mixing containers If a pot of mixed epoxy begins to exotherm heat up quickly move it outdoors Avoid breathing the fumes Do not dispose of the mixture until the reaction is complete and has cooled Do not fill or cast layers of epoxy thicker than 1 2 thinner if enclosed by foam or other insulating material Do not pour into confined spaces Adding fillers and additives Fillers Throughout this and other WEST SYSTEM manuals we refer to epoxy neat epoxy or resin hardener mixture meaning mixed resin and hardener without fillers added and thickened mixture or thickened epoxy meaning mixed resin and hardener with fillers added Fillers are used to thicken epoxy for specific applications such as bonding or fairing After selecting an appropriate filler for your job see Filler Selection Guide use it to thicken the epoxy mixture to the desired consistency The thickness of a mixture required for a particular job is controlled by the amount of filler added There is no
34. re using pumps Before you use the first mixture on a project verify the proper ratio according to the instructions that come with the pumps Re check the ratio anytime you experience problems with curing e Dispensing without Mini Pumps Weight volume measure To measure 105 Resin and 205 or 206 Hardener by weight or volume combine five parts resin with one part hardener To measure 105 Resin and 207 or 209 Hardener by volume combine three parts resin with one part hardener by weight 3 5 parts resin 1 part hardener First time users If this is the first time you have used WEST SYSTEM epoxy begin with a small test batch to get the feel for the mixing and curing process before applying the mixture to your project This will demonstrate the hardener s open time for the temperature you are working in and assure you that the resin nardener ratio is metered properly Mix small batches until you are confident of the mixture s handling characteristics Mixing stir the two ingredients together thoroughly at least 1 minute longer in cooler temperatures Figure 3 To assure thorough mixing scrape the sides and bottom of the pot as you mix Use the flat end of the mixing stick to reach the inside corner of the pot If you are using a power mixer occasionally scrape the sides and corners of the mixing pot while mixing sied comers Figure 3 Stir resin and hardener together thoroughly at least 1 minure longer in cooler tem pe
35. rsized hole can be extended to the end of the fastener Figure 16 Shape and smooth the filet with a rounded filleting tool 1 Drill oversized holes 2 3 3 4 the depth of the fastener The diameter may be up to twice the fastener diameter Figure 16a 2 Drill a normal sized pilot hole at the bottom of the oversized hole to the full length of the fastener The normal sized pilot hole serves to hold or clamp the hardware in position until the epoxy cures 3 Wet out the holes and the fastener with epoxy Allow the epoxy to thoroughly soak into the exposed end grain of the wood 4 Fill the hole with thickened epoxy adhesive filler Use 404 High density preferred or 406 Colloidal Silica 5 Install the fasteners with just enough force to hold the hardware in place Allow the epoxy to cure thoroughly before applying load to the hardware Figure 16b Bonding hardware Bonding hardware goes a step beyond bonding the fasteners only By bonding the hardware base directly to the surface you further increase hardware load capacity and provide a solid bearing surface for the hardware It also seals the wood underneath and is a stronger longer lasting attachment than bonding the fasteners only It is especially useful to mount hardware on curved uneven or unlevel surfaces htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 15 of 24 Figure 17 Figure 18 E HA B Coat the hardware bottom ang T
36. s because it promotes maximum epoxy penetration into the bonding surface and prevents resin starved joints Single step bonding can be used when joints have minimal loads and excess absorption into porous surfaces is not a problem In both cases epoxy bonds best when it is worked into the surface with a roller or brush Before mixing epoxy check all parts to be bonded for proper fit and surface preparation gather all the clamps and tools necessary for the operation and cover any areas that need protection from spills Note The term bonding as used here and other WEST SYSTEM literature refers to structural adhesion or gluing of components not the electrical bonding Two step bonding 1 Wet out bonding surfaces Apply a neat resin hardener mixture without fillers to the surfaces to be joined Figure 9 Wet out small or tight areas with a disposable brush Wet out larger areas with a foam roller or by spreading the resin nardener mixture evenly over the surface with a plastic spreader You may proceed with step two immediately or any time before the wet out coat reaches the final cure stage Apply resinnarde ner mixture Apply thickened opoxy to one to the bonding surfaces of the bonding surfaces 2 Apply thickened epoxy to one bonding surface Modify the resin hardener mixture by stirring in the appropriate filler until it becomes thick enough to bridge any gaps between the mating surfaces and to prevent resin starved joints Apply
37. sheeting or release fabric under the clamps so they don t inadvertently bond to the surface Staples nails or drywall screws are often used where conventional clamps will not work Any fasteners left in should be of a non corroding alloy such as bronze In some cases the thickened epoxy or gravity will hold parts in position without clamps Bonding with fillets A fillet fil it is a cove shaped application of thickened epoxy that bridges an inside corner joint It is excellent for bonding parts because it increases the surface area of the bond and serves as a structural brace All joints that will be covered with fiberglass cloth will require a fillet to Support the cloth at the inside corner of the joint The procedure for bonding with fillets is the same as normal bonding except that instead of removing the squeezed out thickened epoxy after the components are clamped in position you shape it into a fillet For larger fillets add thickened mixture to the joint as soon as the bonding operation is complete before the bonding mixture is fully cured or any time after the final cure and sanding of exposed epoxy in the fillet area 1 Bond parts as described in Bonding 2 Shape and smooth the squeezed out thick epoxy into a fillet by drawing a rounded filleting tool mixing stick along the joint dragging excess material ahead htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 13 of 24 of th
38. stance Acetone toluene or MEK have been used to thin WEST SYSTEM epoxy and duplicate these penetrating epoxies with about the same effectiveness If you chose to thin the epoxy keep in mind that the strength and moisture protection of the epoxy are lost in proportion to the amount of solvent added There is a better solution to get good penetration without losing strength or moisture resistance We recommend moderate heating of the repair area and the epoxy with a heat gun or heat lamp The epoxy will have a lower viscosity and penetrate more deeply when it is warmed and contacts the warmed wood cavities and pores Although the working life of the epoxy will be considerable shortened slower hardeners 206 207 209 will have a longer working life and should penetrate more than 205 Hardener before they begin to gel When the epoxy cures it will retain all of its strength and effectiveness as a moisture barrier which we feel more than offsets any advantages gained by adding solvents to the epoxy Removing Epoxy Removing uncured or non curing epoxy Uncured epoxy is removed as you would spilled resin Scrape as much material as you can from the surface using a stiff metal or plastic scraper warm the epoxy to lower its viscosity Clean the residue with lacquer thinner acetone or alcohol Follow safety warnings on solvents and provide adequate ventilation After recoating wood surfaces with epoxy it s a good idea to brush the wet epoxy in the d
39. taining sawdust or other fine cellulose materials spontaneous combustion can occur htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 7 of 24 Clean resin or mixed epoxy residue with lacquer thinner acetone or alcohol Follow all safety warnings on solvent containers Clean hardener residue with warm soapy water Dispose of resin hardener and empty containers safely Puncture a corner of the can and drain residue into the appropriate new container of resin or hardener DO NOT dispose of resin or hardener in a liquid state Waste resin and hardener can be mixed and cured in small quantities to a non hazardous inert solid CAUTION Large pots of curing epoxy can get hot enough to ignite surrounding combustible materials and give off hazardous fumes Place pots of mixed epoxy in a safe and ventilated area away from workers and combustible materials Dispose of the solid mass only if cure is complete and the mass has cooled Follow federal state or local disposal regulations Thinning Epoxy There are epoxy based products specifically designed to penetrate and reinforce rotted wood These products basically an epoxy thinned with solvents do a good job of penetrating wood But the solvents compromise the strength and moisture barrier properties of the epoxy WEST SYSTEM epoxy can be thinned with solvents for greater penetration but not without the same compromises in strength and moisture resi
40. they do an adequate job of protecting the epoxy barrier from UV radiation In many architectural applications latex paint may be the most suitable coating to use Their durability is limited Alkyd finishes enamel alkyd enamel marine enamel acrylic enamel alkyd modified epoxy traditional varnish and spar varnish offer ease of application low cost low toxicity and easy availability Their disadvantages are low UV resistance and low abrasion resistance One part polyurethanes offer easy application cleanup and better properties than alkyds They are also more expensive and some may be incompatible with amine cure epoxy systems such as WEST SYSTEM epoxy although 207 Hardener may htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 23 of 24 offer better compatibility Test first Epoxy paints are available in one part and two part versions Two part epoxies offer many characteristics similar to the higher performance polyurethanes They are durable and chemical resistant but offer limited UV protection compared to the linear polyurethanes Two part linear polyurethane LP paints offer the most durable protection available LP s are available as pigmented or clear coatings and offer excellent UV protection gloss retention abrasion resistance plus compatibility with epoxy However compared to other types of coatings they are expensive require more skill to apply and present a greater health haz
41. to support the base at the desired height and position e g winch base Figure 19a 3 Apply enough thickened epoxy to cover the blocks If the gap between the base and the surface is over 1 2 fill the gap in two separate layers to avoid exotherm 4 Place the hardware in position resting on the blocks Figure 19b and install the fasteners 5 Smooth the excess epoxy into the desired fillet shape around the base Figure 19c Allow the epoxy to cure fully before loading Protect exposed epoxy from UV Bonding studs Bond threaded rods or studs into the substrate instead of bolts or screws and attach the hardware with nuts This variation is appropriate for many engine motor or machine installations Coat the base with wax mold release to make the htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 16 of 24 hardware removable Although the hardware is not bonded to the substrate the epoxy still provides a bearing surface that perfectly matches and supports the base of the hardware Figure 20 Bond threaded rods or studs Into the substrate as an altemative for easily removable hardware 1 Prepare the studs threaded rods by waxing the upper ends above the surface and cleaning the lower ends below the surface 2 Place a nut and washer on the studs wet out the lower ends and push them into the epoxy filled holes Allow the epoxy to cure thoroughly before tightening the nuts Fig
42. tration but not without the same compromise in strength and moisture resistance Acetone toluene or MEK have been used to thin WEST SYSTEM epoxy and duplicate these penetrating epoxies with about the same effectiveness If you chose to thin the epoxy keep in mind that the strength and moisture protection of the epoxy are lost in proportion to the amount of solvent added There is a better solution to get good penetration without losing strength or moisture resistance We recommend moderate heating of the repair area and the epoxy with a heat gun or heat lamp The epoxy will have a lower viscosity and penetrate more deeply when it is warmed and contacts the warmed wood cavities and pores Although the working life of the epoxy will be considerable shortened Slower hardeners 206 207 209 will have a longer working life and should penetrate more than 205 Hardener before they begin to gel When the epoxy cures it will retain all of its strength and effectiveness as a moisture barrier which we feel more than offsets any advantages gained by adding solvents to the epoxy Removing epoxy Removing uncured or non curing epoxy Uncured epoxy is removed as you would spilled resin Scrape as much material as you can from the surface using a stiff metal or plastic scraper warm the epoxy to lower its viscosity Clean the residue with lacquer thinner acetone or alcohol Follow safety warnings on solvents and provide adequate ventilation After recoating
43. ure 20 Removing fasteners If you know that you will want to remove the fastener you can coat the threads with wax or mold release contaminating the surface enough to prevent a good bond Remove a permanently bonded fastener by applying heat to the head of the fastener with a soldering iron or propane torch Use a heat shield to protect the Surrounding area Heat will travel down the fastener softening the epoxy in contact with it At about 120 F the epoxy should soften enough to allow the fastener to be backed out Allow more time for heat to travel down longer or larger diameter fasteners Fairing Fairing refers to the filling and shaping of low areas so they blend with the Surrounding surfaces and appear fair to the eye and touch After major structural assembly has been completed final fairing can be easily accomplished with WEST SYSTEM epoxy and low density fillers Figure 21 Figure 22 Wet out porous surfaces Apply fairing compound to fill before applying fairing compound all voids and smooth to shape 1 Prepare the surface as you would for bonding Sand smooth any bumps or ridges on the surface and remove all dust from the area to be faired htto www westsystem com webpages userinfo manual 10 9 2007 WEST SYSTEM User Manual Page 17 of 24 2 Wet out porous surfaces with unthickened epoxy Figure 21 3 Mix resin hardener and 407 Low Density or 410 Microlight filler to a peanut butter consistency
Download Pdf Manuals
Related Search