Home
DBI/SALA Door/Window Jamb Anchor - Instruction
Contents
1. 5 3 5 4 INSPECTION STEPS Step 1 Inspect the Door Jamb Anchor for damage Look for cracks dents or deformities Look for bending or wear on the support tube D ring and adjustment mechanisms Ensure no parts are loose or missing Step 2 Inspect the adjustment mechanisms The detent pin must lock when inserted through any of the adjustment holes Step 3 Inspect entire unit for excessive corrosion Step 4 Inspect labels All product information labels must be present and fully legible Step 5 Record the inspection date and results in the inspection and maintenance log in section 9 0 of this manual IF INSPECTION REVEALS AN UNSAFE OR DEFECTIVE CONDITION REMOVE UNIT FROM SERVICE AND DESTROY OR RETURN TO DBI SALA FOR REPAIR NOTE Only DBI SALA or parties authorized in writing may make repairs to this equipment 6 0 6 1 6 2 7 0 7 1 7 2 MAINTENANCE SERVICING STORAGE CLEANING Periodically clean the Door Jamb Anchor using water and a mild soap solution Do not use acids or other caustic chemicals that could damage the system components USER EQUIPMENT Maintain service and store harness and personal fall arrest components according to manufacturer s instructions SPECIFICATIONS MATERIALS All materials used in the construction of this equipment are as follows Aluminum Alloy Anchor Zinc Plated Alloy Steel D ring DI MENSI ONS AND WEIGHT Size Adjustable to fit 21 1 2 in
2. s exclusive remedy under this warranty is limited to the repair or replacement in kind of any defective product within its lifetime as CAPITAL SAFETY in its sole discretion determines and deems appropriate No oral or written information or advice given by CAPITAL SAFETY its distributors directors officers agents or employees shall create any different or additional warranties or in any way increase the scope of this warranty CAPITAL SAFETY will not accept liability for defects that are he result of product abuse misuse alteration or modification or for defects that are due to a failure NEGLIGENCE OR OTHER LEGAL OR EQUITABLE THEORY o install maintain or use the product in accordance with the manufacturer s instructions CAPITAL SAFETY S WARRANTY APPLIES ONLY TO THE END USER THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO OUR PRODUCTS AND IS IN LIEU OF ALL OTHER WARRANTIES AND LIABILITIES EXPRESSED OR IMPLIED CAPITAL SAFETY EXPRESSLY EXCLUDES AND DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND SHALL NOT BE LIABLE FOR INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING WITHOUT LIMITATION LOST PROFITS REVENUES OR PRODUCTIVITY OR FOR BODILY INJ URY OR DEATH OR LOSS OR DAMAGE TO PROPERTY UNDER ANY THEORY OF LIABILITY NCLUDING WITHOUT LIMITATION CONTRACT WARRANTY STRICT LIABILITY TORT INCLUDING CSG USA amp Latin America 3833 SALA Way Red Wing MN 5506
3. in a swing fall may cause serious injury or death Minimize swing falls by working as close to the anchorage as possible Do not permit a swing fall if injury could occur Swing falls will significantly increase the clearance required when a self retracting lifeline or other variable length connecting subsystem is used F FALL CLEARANCE There must be sufficient clearance below the user to arrest a fall before the user strikes the ground or other obstruction The clearance required is dependent on the following factors Elevation of Door Jamb Anchor Length of connecting subsystem Deceleration distance Movement of harness attachment element sliding D ring Worker height Free fall distance See personal fall arrest system manufacturer s instructions for more information WORK ZONE See Figure 3 Do not extend your work zone more than 30 degrees from either side of the anchorage point Do not use the door jamb anchor in a way such that it can be loaded at an angle above the level of the anchorage point Do not climb above the anchor point Figure 3 Work Zone 90 VERTICAL PLANE HORIZONTAL PLANE 1 3 2 0 2 1 ENVIRONMENTAL HAZARDS Use of this equipment in areas with environmental hazards may require additional precautions to reduce the possibility of injury to the user or damage to the equipment Hazards may include but are not limited to heat chemicals corrosive environments high v
4. 55 cm to 51 1 2 in 131 cm openings Weight 14 Ibs 6 4 kg 11 Dimensions L 60 38 in d i 153 0 cm 6 00 in 15 2 cm 6 25 in J 7 3 CAPACITY Capacity 1 user 310 Ibs 141 kg maximum weight Strength 3 600 Ibs 16 kN in directions specified in section 1 2 8 0 LABELING 8 1 The following labels must be present and fully legible SPECIFIC e VERTICAL PLANE WINDOW DOOR JAMB ANCHOR Tis fice LE ae dpa b I LOT MODEL NO HORIZONTAL PLANE oge 2100080 12 INSPECTION AND MAINTENANCE LOG SERIAL NUMBER MODEL NUMBER DATE PURCHASED DATE OF FIRST USE INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By INSPECTION AND MAINTENANCE LOG SERIAL NUMBER MODEL NUMBER DATE PURCHASED DATE OF FIRST USE INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By Approved By Approved B
5. 6 5005 Toll Free 800 328 6146 Phone 651 388 8282 Fax 651 388 5065 solutions capitalsafety com CSG EMEA Europe Middle East Africa Le Broc Center Z 1 l re Avenue 5600 M B P 15 06511 Carros Le Broc Cedex France Phone 33 4 97 10 00 10 Fax 33 4 93 08 79 70 information capitalsafety com DBI The Ultimate in Fall Protection CSG Canada 260 Export Boulevard Mississauga ON L5S 1Y9 Phone 905 795 9333 Toll Free 800 387 7484 Fax 888 387 7484 info ca capitalsafety com CSG Australia amp New Zealand 95 Derby Street Silverwater Sydney NSW 2128 AUSTRALIA Phone 61 2 8753 7600 Toll Free 1 800 245 002 AUS Toll Free 0800 212 505 NZ Fax 61 2 87853 7603 sales capitalsafety com au www capitalsafety com CSG Northern Europe 5a Merse Road North Moons Moat Reditch Worcestershire UK B98 9HL Phone 44 0 1527 548 000 Fax 44 0 1527 591 000 csgne capitalsafety com CSG Asia Singapore 16S Enterprise Road Singapore 627666 Phone 65 65587758 Fax 65 65587058 inquiry capitalsafety com Shanghai Rm 1406 China Venturetech Plaza 819 Nan Jing Xi Rd Shanghai 200041 P R China Phone 86 21 62539050 Fax 86 21 62539060
6. ANSI Z359 1 for certification definition or B 5 000 Ibs 22 2 kN in the absence of certification Per OSHA 1926 500 and 1910 66 Anchorages used for attachment of a personal fall arrest system shall be independent of any anchorage being used to support or suspend platforms and must support at least 5 000 Ibs 22 2 kN per user attached or be designed installed and used as part of a complete personal fall arrest system which maintains a safety factor of at least two and is supervised by a qualified person INSTALLATION AND USE WARNING Do not alter or intentionally misuse this equipment Consult DBI SALA when using this equipment in combination with components or subsystems other than those described in this manual Some subsystem and component combinations may interfere with the operation of this equipment Use caution when using this equipment around moving machinery electrical hazards chemical hazards and sharp edges WARNING Consult your doctor if there is reason to doubt your fitness to safely absorb the shock from a fall arrest Age and fitness seriously affect a worker s ability to withstand falls Pregnant women or minors must not use DBI SALA anchorage connectors 3 1 3 2 BEFORE EACH USE OF THIS EQUIPMENT INSPECT IT ACCORDING TO SECTION 5 0 OF THIS MANUAL INSTALLATION The Door Jamb Anchor may be installed in any door or window opening meeting the requirements specified in section 1 2 and meetin
7. Instructions for the following series products Door Jamb Anchor Model Numbers 2100029 2100080 The Ultimate in Fall Protection USER INSTRUCTION MANUAL DOOR J AMB ANCHOR This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359 1 and should be used as part of an employee training program as required by OSHA ee Copyright 2013 Capital Safety Figure 1 Door Jamb Anchor 21 1 2 In Min 51 1 2 In Max 55 cm min 131 cm Max Pe cause Bar ee Adjustment Knob Coarse Adjustment Pin and Holes WARNING This product is part of a personal fall protection system The user must read and follow the manufacturer s instructions for each component of the system These instructions must be provided to the user of this equipment The user must read and understand these instructions before using this equipment Manufacturer s instructions must be followed for proper use and maintenance of this equipment Alterations or misuse of this equipment or failure to follow instructions may result in serious injury or death IMPORTANT If you have questions on the use care or suitability of this equipment for your application contact DBI SALA IMPORTANT Record the product identification information from the ID label in the inspection and maintenance log in section 9 0 of this manual DESCRIPTION Door Jamb Anchor 2100080 For door or window openi
8. ful rescue Training should be provided on a periodic basis to ensure rescuers proficiency TRAINING It is the responsibility of the user to assure they are familiar with these instructions and are trained in the correct care and use of this equipment User must also be aware of the operating characteristics application limits and the consequences of improper use of this equipment INSPECTION FREQUENCY Before each use inspect the Door Jamb Anchor according to sections 5 3 and 5 4 See Figure 1 for parts identification The Door Jamb Anchor must be formally inspected by a competent person other than the user at least annually Record the results in the inspection and maintenance log IMPORTANT If this equipment has been subject to fall arrest forces it must be removed from service and destroyed or returned to DBI SALA for inspection or repair 5 2 1 SAFE RFID TAG The Door Jamb Anchor includes an i Safe Radio Frequency Identification RFID tag The RFID tag can be used in conjunction with the i Safe handheld reading device to simplify inspection and inventory control and provide records for your fall protection equipment If you are a first time user contact a Capital Safety Customer Service representative see back cover or if you have already registered go to isafe capitalsafety com Follow the instructions provided with your i Safe handheld reader or software to transfer your data to your database 10
9. g the strength requirements specified in section 2 5 Step 1 Adjust the Door Jamb Anchor to fit inside the desired opening by removing the detent pin and sliding the adjustable leg toward the D ring Make sure the fine adjustment pad is adjusted so that it is tight against the support bar See Figure 6 8 FIGURE 6 INSTALLATION Step 1 Adjustment Pad Detent Pin Sat Fine Adjustment Knob Step 2 Place the Door Jamb Anchor in the door or window opening with the D ring facing the area where work will be performed The adjustable leg may be located either on the left or right side of the opening The Door J amb Anchor must rest on the bottom of the window or door opening Do not attempt to install the Door Jamb Anchor in a position where it is not supported by the floor or window sill WARNING This Door J amb Anchor must be installed at the bottom of the window or door opening resting on the sill If the anchor is not resting on the sill it may rotate when loaded allowing the anchor to come free of the window or door opening Failure to follow this warning may result in serious injury or death Step 3 Slide the adjustable leg as close to the door or window jamb as possible and insert the detent pin in a corresponding set of adjustment holes Secure the anchor using the fine adjustment knob by rotating the knob clockwise 3 3 USING THE DOOR J AMB ANCHOR A PERSONAL FALL ARREST SYSTEM Ins
10. gate presses against 3 The gate opens allowing snap hook the connecting ring the snap hook to slip off NOTE Large throat opening snap hooks should not be connected to standard size D rings or similar objects which will result in a load on the gate if the hook or D ring twists or rotates Large throat snap hooks are designed for use on fixed structural elements such as rebar or cross members that are not shaped in a way that can capture the gate of the hook C In a false engagement where features that protrude from the snap hook or carabiner catch on the anchor and without visual confirmation seems to be fully engaged to the anchor point D To each other E Directly to webbing or rope lanyard or tie back unless the Figure 5 I nappropriate Connections 2 5 3 0 manufacturer s instructions for both the lanyard and connector specifically allows such a connection To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock or that roll out could occur In a manner that does not allow the connector to align properly while under load ANCHORAGE STRENGTH Door Jamb Anchors installed for fall arrest applications must be attached to a door or window opening capable of sustaining static loads in the directions permitted by the personal fall arrest system when in use of at least A 3 600 Ibs 16 KN when certification exists see
11. ngs sized 21 1 2 in 55 cm to 51 1 2 in 131 cm wide See Figure 1 1 0 APPLICATIONS 1 1 PURPOSE The Door Jamb Anchor is an anchorage connector for a personal fall arrest system designed to be temporarily installed in a door or window opening 1 2 LIMITATIONS The following application limitations must be considered before using this equipment A OPENING SIZES The Door Jamb Anchor may be installed in jambs with opening sizes ranging from 21 1 2 in 55 cm to 51 1 2 in 131 cm wide B CAPACITY This equipment is designed for use by persons with a combined weight clothing tools etc of no more than 310 Ibs 141 kg No more than one personal protective system may be connected to this equipment at one time C PERSONAL FALL ARREST SYSTEM The personal fall arrest system used with this equipment must meet the requirements specified in section 2 1 D FREE FALL Personal fall arrest systems used with this equipment must be rigged to limit the free fall to a maximum of 6 feet when possible as required by OSHA The maximum free fall must always be within the manufacturer s free fall capacity of the system components used to arrest the fall See section 2 1 and connecting subsystem manufacturer s instructions for more information E SWING FALLS See Figure 2 Figure 2 Swing Fall Swing falls occur when the anchorage point is not directly above or below the point where a fall occurs The force of striking an object
12. oltage power lines gases moving machinery and sharp edges Contact DBI SALA if you have questions about using this equipment where environmental hazards exist TRAINING This equipment must be installed and used by persons trained in its correct application and use See section 4 0 APPLICABLE STANDARDS Refer to national standards including ANSI Z359 1 and local state and federal requirements for more information personal fall arrest systems and associated components SYSTEM REQUIREMENTS PERSONAL FALL ARREST SYSTEM The Door J amb Anchor is designed for use with DBI SALA approved components or subsystems Use of this equipment with non approved components may result in incompatibility between equipment and could affect the reliability and safety of the complete system Personal fall arrest systems used with this equipment must meet applicable OSHA state federal and ANSI requirements A full body harness must be worn by the worker when connected to the Door Jamb Anchor As required by OSHA the personal fall arrest system must be capable of arresting a worker s fall with a maximum arresting force no greater than 1 800 Ibs 8 KN and where possible limit the free fall distance to 6 ft 1 83 m or less If the maximum free 2 2 2 3 2 4 fall distance of 6 ft 1 83 m must be exceeded the employer must be able to document based on test data that the maximum permissible arresting forces will not be exceeded and tha
13. ot compatible Non compatible connectors may unintentionally disengage See Figure 4 Connectors must be compatible in size shape and strength Self locking snap hooks and carabiners are required by ANSI Z359 1 OSHA and CSA 2259 12 MAKING CONNECTIONS Only use self locking snap hooks and carabiners with this equipment Only use connectors that are suitable to each application Ensure all connections are compatible in size shape and strength Do not use equipment that is not compatible Ensure all connectors are fully closed and locked DBI SALA connectors snap hooks and carabiners are designed to be used only as specified in each product s user s instructions See Figure 5 for inappropriate connections DBI SALA snap hooks and carabiners should not be connected To a D ring to which another connector is attached In a manner that would result in a load on the gate 6 Figure 4 Unintentional Disengagement Roll out If the connecting element that a snap hook shown or carabiner attaches to is undersized or irregular in shape a situation could occur where the connecting element applies a force to the gate of the snap hook or carabiner This force may cause the gate of either a self locking or a non locking snap hook to open allowing the snap hook or carabiner to disengage from the connecting point Small ring or other non compatibily shaped connector lt gt SRO Gro 1 Force is applied to the 2 The
14. pect and don your full body harness according to manufacturer s instructions Attach the connecting subsystem energy absorbing lanyard to the dorsal D ring on the harness B STRUCTURE Ensure the structure you will be connecting to is properly supported before using this equipment Approach the structure using appropriate access equipment C OTHER CONSI DERATI ONS When working on a structure do not take unnecessary risks such as jumping or reaching too far from the edge Be aware of all environmental hazards in the area Do not allow your connecting subsystem to pass 4 0 4 1 5 0 5 1 under your arms or between your feet To avoid inadequate fall clearance do not climb above or to the side of the Door J amb Anchor SHARP EDGES Avoid working where the connecting subsystem energy absorbing lanyard or other system components will be in contact with or abrade against unprotected sharp edges If working around sharp edges is unavoidable protection against cutting must be provided through the use of a protective cover IN THE EVENT OF A FALL The responsible party must have a rescue plan and the ability to implement a rescue Tolerable suspension time in a full body harness is limited so a prompt rescue is critical RESCUE With the number of potential scenarios for a worker requiring rescue an on site rescue team is beneficial The rescue team is given the tools both in equipment and technique to perform a success
15. t the personal fall arrest system will function properly When a free fall greater than 6 feet and up to a maximum of 12 ft 3 66 m is possible DBI SALA recommends using a personal fall arrest system incorporating a DBI SALA Force2 energy absorbing lanyard DBI SALA has performed testing using the Force2 energy absorbing lanyard in free falls up to 12 ft 3 66 m to ensure the maximum arresting force does not exceed 1 800 Ibs 8 kN and the system functions properly The results of these tests are listed in the user instruction manual provided with Force2 shock absorbing lanyards COMPATIBILITY OF COMPONENTS DBI SALA equipment is designed for use with DBI SALA approved components and subsystems only Substitutions or replacements made with non approved components or subsystems may jeopardize compatibility of equipment and may effect the safety and reliability of the complete system COMPATIBILITY OF CONNECTORS Connectors are considered to be compatible with connecting elements when they have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently open regardless of how they become oriented Contact DBI SALA if you have any questions about compatibility Connectors hooks carabiners and D rings must be capable of supporting at least 5 000 Ibs 22 2 kN Connectors must be compatible with the anchorage or other system components Do not use equipment that is n
16. y Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By INSPECTION AND MAINTENANCE LOG SERIAL NUMBER MODEL NUMBER DATE PURCHASED DATE OF FIRST USE INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By LIMITED LIFETIME WARRANTY Warranty to End User D B Industries Inc dba CAPITAL SAFETY USA CAPITAL SAFETY warrants to the original end user End User that its products are free from defects in materials and workmanship under normal use and service This warranty extends for the lifetime of the product from the date the product is purchased by the End User in new and unused condition from a CAPITAL SAFETY authorized distributor CAPITAL SAFETY S entire liability to End User and End User
Download Pdf Manuals
Related Search
Related Contents
PDFファイル Avaya Configuring Data Encryption Services User's Manual Invisorb Spin Blood Midi Kit User manual Les communautés virtuelles peuvent-elles Online Technology Guide Elementary Linear Algebra, 6e Samsung RT14MBSS Hướng dẫn sử dụng 4. Using CD Player / CD Changer MANUALE TECNICO POWERJET GPR WD Elements™ Play™ Multimedia Drive - Product TC-ZXAシリーズ Copyright © All rights reserved.
Failed to retrieve file