OFFSET DOUBLE BOWL SINK
Contents
1. of the same size as the hole that you will cut out to accomodate the sink As this sink is 31 5 in x 20 5 in 800 mm x 521 mm we recommend that you use a template size of 29 3 8 in x 18 3 8 in 746 mm x 467 mm with square corners NOTE The flat mating surface of the sink that will touch the underside of your counter is 1 1 16 in 27 mm wide on all four sides Mark the center point 6 of the sink on the template Cut the template out of the piece of cardboard or paper 29 3 8 in 746 mm co eo oo gt E a N 3 3 3 3 1 2 4 in 89 102 mm CUTTING THE COUNTER A CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury Place the template 8 on the counter with its front 2 parallel to the front of the counter 7 Ensure that it is placed so that the sink will clear all objects and the mounting hardware can be installed Make sure there is a minimum of 3 in 76 2 mm of space underneath on all four sides for the undermount clips E Place a line of tape 9 around the template and trace the template onto the tape with a pencil Double check the location of the cut line before removing the template Use a saber saw or jig saw to cut along the cut line Place a support underneath the cut out portion of the counter to prevent it from falling during cutting LESA A Installation continued DRILLING THE HOLES FOR THE UND2. AL Carpenter s square Electric drill with 3 8 in 10 mm drill bit and 1 in 25 4 mm or 3 in 76 2 mm hole saw Wrenches 2 Pipe wrench Silicone sealant PA Pencil Hacksaw Safety goggles Tail pipe 2 i al Teflon tape cB CM Supply lines 2 Pre Installation continued PACKAGE CONTENTS COTO tty A Stamesssteetank A 5 wnswmgeme sramr E o wmoncams 9 E undermountcamps O rmm ECT 5 CONGLOMKB COM Please contact customer service amp conglomkb com or 1 877 333 0098 for further assistance Installation UNDERMOUNT INSTALLATION CREATING THE TEMPLATE NOTE Undermount sinks are mounted from below the counter If you are installing a topmount or drop in sink please see topmount installation on page 9 It is highly recommended that undermounting be performed by a professional installer Improper installation will void the warranty Using a carpenter s square draw a line 5 from front to back on the bottom of the counter to indicate the location of the center of the sink Draw a line 2 parallel to the front edge of the counter to indicate how far back the sink should be located from the front of the counter 7 Typical setback is 3 1 2 4 in 89 mm 102 mm from the front of the counter depending on the cabinet structure the counter overhang the type of sink bowl and the deck size On a piece of cardboard or paper draw a rectangle
3. ERMOUNT CLIPS DN CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury On the underside of the counter mark the location of the ten holes 5 for the undermount clips E These holes should be equally spaced around the perimeter of the cut out with three on each side 2 and 4 and two on each side 1 and 3 They should be set back from the cut out opening by 1 1 2 in 38 mm Using an electric drill with a 3 8 in 10 mm drill bit drill each hole so that it is 3 8 in 10 mm in diameter and 5 8 in 15 8 mm deep 7 TESTING THE FIT OF THE SINK Place the sink A underneath the cut out in the counter to test its fit Ensure that the reveal is equal on all four sides when viewed from above Make adjustments to the cut out if necessary When you are satisfied with the location of the sink A mark the location of the edge of the counter cut out on at least two sides of the lip of the sink CONGLOMKB COM Please contact customer service amp conglomkb com or 1 877 333 0098 for further assistance Installation continued INSTALLING THE SINK NOTE Install the faucet according to the manufacturers instructions before this step Install the vanishing edge strainer according to the instructions before completing this step See page 11 Put the threaded inserts on the bolts of the undermount clips E loosely in the holes that you drilled for them in the un
4. PRESEN 7A STAINLESS STEEL ez A OFFSET DOUBLE BOWL SINK INSTALLATION GUIDE AND USER MANUAL Model No QK031 Table of Contents Table of Contents 00000 eee eee eee eee 2 Installation Safety Information 00 cece eee eee eens 2 Un derMOUNE s iu ceca rra rai 6 Warranty TOPMOU E 2s acne zd DHL RR RUE dd sa 9 One Year Limited Warranty 00 00 00 cece eens 3 Installing the Vanishing Edge Strainer 11 Warranty Claim Procedure 0 cc cece eee eaes 3 Installing the Bottom Grid o ooooooo 11 Pre Installation Care and Cleaning lseeeeeeeeeeeeee 12 Planning Installation 0 0 cece cece ee eens 4 Service Parts ccccceec eee e ee ee ee eeeeeeaeeeeee 13 Tools Required iss euin Eme hia E a ena 4 Parts REUE d iens nu cem en 4 Package Contents 55k err nmm nh Rite 5 Safety Information READ AND SAVE THESE INSTRUCTIONS n CAUTION Always wear safety goggles and gloves during installation to prevent personal injury 1 Inspect your unit before proceeding Once you unpack your H Dl ai unit check for chips scratches cracks dents or scuff marks If any damage is noticed do not install 2 Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer 3 Installation work and plumbing must be done by qualified person s in accordance with all applicable codes and sta
5. derside of the counter Ensure that the clamps of the undermount clips E are turned so that they do not interfere with the placement of the sink Place a small bead of silicone sealant not included around the upper lip of the sink A Carefully place the sink A into its location under the counter lining up the pencil marks on the lip of the sink that you made when you tested the fit of the sink Carefully rotate the clamps of the undermount clips E over the clamp bar on the sink A and gently tighten the bolts see tightening sequence of the undermount clips E working from side to side to fasten the sink A firmly Recheck the alignment visually from above Wipe away any excess silicone and for best results allow the bond to rest undisturbed for 8 hours or overnight Install the counter as directed by the manufacturer and install all other plumbing as required 3 5 1 Tightening sequence for clips SUPPLY LINES NOT INCLUDED The supply lines which connect the faucet to the household water system are not supplied with this unit They need to be purchased separately Follow the supply line manufacturer s instructions for proper installation Installation continued TOPMOUNT INSTALLATION CREATING THE TEMPLATE CUTTING THE COUNTER NOTE Topmount sinks are dropped into the counter from above If you are PN Mediae ee koci UN EWES UTED installing an undermount sink please see undermount installatio
6. ep See page 11 Apply silicone sealant not included around the underside of the lip of the sink A on all four sides Carefully lower the sink A into the counter ensuring that the factory installed topmount clips D do not catch on the counter edges Slide each topmount clip D along the rails so that they are evenly spaced around the sink A Swing the clamps on the topmount clips D and tighten the screws progressively see tightening sequence below until the sink rim is flush with the counter Check the alignment as you tighten so that the front of the sink A is parallel to the front of the counter Adjust and re tighten if necessary Do not over tighten Wipe away any excess sealant with a rag 10 8 3 5 1 Tightening sequence for clips A Q N a_ SUPPLY LINES NOT INCLUDED The supply lines which connect the faucet to the household water system are not supplied with this unit They need to be purchased separately Follow the supply line manufacturer s instructions for proper installation Installation continued INSTALLING THE VANISHING EDGE STRAINER NOTE If you are installing a garbage disposer not supplied do not install the strainer You will need to purchase from Conglom Kitchen amp Bath an adaptor This will replace the flange from your garbage disposer Install the garbage disposer according to the manufacturer s installation instructions replacing t
7. he flange for the adaptor Apply a small amount of plumber s putty not included in the notch around the drain hole of the sink Connect the upper strainer body C2 and the strainer ring C3 and insert them into the drain hole from the top of the sink Connect the strainer gasket C4 and lower strainer body C5 and insert them into the drain hole from underneath the sink 1 Not supplied Insert the strainer screw C1 through the entire assembly from the upper strainer body C2 to the lower strainer body C5 Tighten with a Phillips 2 screwdriver Connect the plastic flange 1 and tail pipe 2 and thread the connecting nut 3 through the tail pipe and flange up to the lower strainer body D5 3 amp eg Not supplied Lock the connecting nut by hand NOTE The plastic flange 1 tail pipe 2 and connecting nut 3 are not supplied INSTALLING THE BOTTOM GRID Ensure that the vanishing edge strainer basket B is already in the sink A before placing the bottom grid F The bottom grid F must be positioned with its rubber supports down Tilt the grid up so it is at a slight angle slide it into the sink A and place it so that it is sitting flat on the bottom of the sink 11 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Care and Cleaning Your sink is manufactured with the highest grade stainless steel and will prov
8. ide you many years of enjoyment with the proper care After use always rinse your sink with tap water to Do not allow any food detergent soap or grease dilute and remove deposits to dry or sit for extended periods of time on the surface of the sink Towel dry the sink after use whenever possible to prevent water spots Should water spots occur Never use abrasive cleaning products as they will clean with a mild solution of vinegar and water dull and scratch the finish followed by a thorough rinse Do not use scouring pads on the deck as they will Use liquid soap a general household cleaner or dull the mirror finish a weak solution of vinegar and water for regular cleaning Never use steel wool pads as they will leave iron particles on the sink which will cause corrosion Only use plastic scouring pads recommended for use in stainless steel sinks and only use them in Never leave steel or cast iron pans in your the bowl of the sink Scrub in the direction of the sink for extended periods of time as this can grain original polish lines cause corrosion 12 Service Parts If you are missing parts or if you require replacement parts please call our customer service team at customer service conglomkb com or 1 877 333 0098 8 30 am 5 pm EST Monday Friday Identify the required part s and have the part number s ready COC CTE a vosgocgoraranos oi 2 Po smwesenw Jors 2 Fo iremante oros 10 Pe io
9. le defect occurs or replacement parts are needed please contact our customer service team at customer service conglomkb com or 1 877 333 0098 8 30 am 5 pm EST Monday Friday Before you make your call please ensure that you have Model number or description Proof of sale Details regarding the defect and or part number Name s and address es of the owner and or installer 3 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Pre Installation PLANNING INSTALLATION Inspect your unit before proceeding Check the surface for any flaws or damage including dents bends bumps or scuff marks If any damage is noticed do not proceed with installation Please return the unit to place of purchase for an exchange If there are any missing parts please contact the manufacturer for replacements You may choose to install this sink either undermount from below the counter or topmount from above the counter You must install this sink only in a counter at least 36 in 914 mm wide with a solid surface that has a minimum thickness of at least 3 4 in 19 mm Protect the entire surface of the product during installation to prevent damage TOOLS MATERIALS REQUIRED Measuring tape Saber saw or Jig saw Plumber s putty a Phillips screwdriver PARTS REQUIRED NOT INLCUDED NOTE Plastic Parts not shown to actual size flange 2 Safety gloves C
10. ma douse 1 13 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Imported by Conglom KITCHEN amp BATH St Laurent Qu bec H4S 2C3 1 877 333 0098 customer service conglomkb com www conglomkb com Made in China
11. n 9p p p jury on page 6 Using an electric drill with a 1 in 25 4 mm hole saw Place the sink A upside down on the counter Center the carefully drill four holes 3 inside the cut line sink A on the counter so that it is parallel to the front of the counter ensuring that it will not interfere with the inside structure of the cabinet or the counter It must clear the overhang of the counter and the front inside face of the cabinet Trace the outline of the sink A with a pencil Insert the sink A into the cut out in the counter to test the fit Make adjustments to the cut out if Draw a new line 2 3 8 in 9 5 mm inside the first line RE ee a AMS CUT OME Tinea 1 This will be the cut line As this sink is 31 5 in x 20 5 in 800 mm x 521 mm the cut line should be 30 3 4 in x 19 3 4 in 781 mm x 501 mm Use a saber saw or jig saw to cut along the cut line 2 Place a support underneath the cut out portion of the counter to prevent it from falling during cutting 303 4in ______ 781 mm 19 3 4 in Corner radius 501 mm 1 2 in 12 7 mm 9 CONGLOMKB COM Please contact customer service conglomkb com or 1 877 333 0098 for further assistance Installation continued INSTALLING THE SINK NOTE Install the faucet according to the manufacturers instructions before this step Install the vanishing edge strainer according to the instructions before completing this st
12. ndards 4 Protect the entire surface during installation Warranty ONE YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation Conglom Kitchen amp Bath warrants this product to be free from defects in materials or workmanship for one 1 year from the date of purchase Proof of purchase original sales receipt from the original consumer purchaser must be made available to Conglom Kitchen amp Bath for all warranty claims This warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s instructions It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen amp Bath replacement parts Replacement parts may be obtained by e mail at customer service conglomkb com or by calling 1 877 333 0098 between 8 30 am 5 00 pm EST installation error abuse misuse or improper care and maintenance whether performed by a plumber contractor service provider or member of the purchaser s household The warranty excludes damage due to aggressive air or water conditions harsh or abrasive cleaners and or materials Under no circumstance shall we be held liable for personal injury or property damage resulting fr
13. om improper installation or use of this product We will not be held liable for inconvenience caused by loss of use of this product costs incurred for labour or materials removal and installation of replacement units or any other incidental or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user Our obligation shall be limited to the repair or replacement of a unit at our discretion that may prove by our sole examination to be defective under normal use and service during the warranty period Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not limited to Improper installation not in accordance with manufacturer s instructions Dents and or scratches incurred during shipping handling or installation Change in colour or finish due to chemical usage Damage caused by failure to follow care and cleaning guidelines including damage caused by the use of abrasive cleaners Alterations made to the unit by the purchaser or installer Damage caused by accidental impact fire flood freezing and normal wear Bends and warping caused by forced connections over tightened fittings and inadequate support during installation This warranty does not extend to commercial and institutional installation or use WARRANTY CLAIM PROCEDURE If a claimab
Download Pdf Manuals
Related Search