Dudek Universal User`s Manual
Contents
1. Check main carabiners They must be properly mounted closed and locked 3 2 1 LAUNCH Classic forward launch should be used with little or no wind Facing the wind place the risers over your shoulders A riser must lay on top Clip it into carabiners and lock them Grip the brake handles and A risers marked with yellow band holding them at the stitching just under the quick links Spread out your slightly bent hands keeping them down and back All risers but the A should be placed near your elbow joints Apply some tension to check if the A risers stay on top and the lines are not tangled Take a step back bow down a little and run forward After the initial inflation smoothly move the hands with the risers up and over your head until the wing will be directly above you Check the wing and let the A risers loose Pump out possible faults and keep an eye on position of the paraglider Side drift is corrected best by moving yourself always under center of the canopy launch space permitting In order to keep wing in the air the suspension lines must stay taut all the time so in light winds you will have to run forward With stronger winds you can control the wing while standing still When leaving the ground apply some brakes then release it after gaining some distance from the ground Keep your hands relaxed Reverse launch To be used when wind speed exceeds 3 m s After clipping the risers into carabiners as for the forw2. Universal aerofoil is another product of our DRA Dudek Reflex Airfoil technology It was calculated with our previous experiences in mind and thoroughly tested with numerical methods Dudet Reflus Avfoi Properties of a reflex airfoil were described above The suspension points areas are additionally reinforced with laminated fabric so that loads are equally distributed on three planes vertically through the ribs diagonally through VSS system and level through the RSS All crossports have been prepared using OCD Optimised Crossports Design technology Carefully designed shapes of the openings and their optimal placement between stress lines guarantee very efficient pressure distribution in the canopy and its quick inflation These openings are scaled together with the ribs so that their replicability is flawless and they do not disturb the aerofoil in any way The Universal leading edge is closed to airflow and its precise shape is guarded by reinforcements of laminated fabric Another feature of the Universal is the Flexi Egde technology The leading edge is closed to the airflow and its precise shape is kept with laminated cloth FianiEckga Technology reinforcements incorporating synthetic rods The rods make the leading edge stiffer and smoother bringing improvements in many areas from easier inflation through stiffening the canopy in flight to improved general airflow Cell openings are positioned on the undersurf
3. Dudek Paragliders ul Centralna 2U 86 031 Osielsko Poland tel 48 52 324 17 40 export dudek eu www dudek eu ELOS LE A
4. i Ea ES C 78 E cd Ga COURS e so a E E BU Tele sists ES E lials Fi E Gai di GA Ei tun ON E I T E I O Fi PI E E di 1 E E o lo fs p E ES ES ES PS CE lt ES lo fo fo E EN EA EA E Oats o i ARR E D fo lt i l E Isis E on E D pi 2 p lt a a IE ola ES D 3 zl E e 2 N 00 pa N N e Universal 6 WARRANTY AND AEROCASCO Purchase of a new paraglider is a serious expense for any pilot That is why we cover our paragliders with extensive warranties and additionally offer an AeroCasco insurance against damage and repair costs WARRANTY Dudek Paragliders guarantees free of charge repairs caused by the material or production faults along following scheme For the free flying paragliders warranty covers 36 months 3 years or 300 flight hours depending on what comes first If the paraglider is used for powered flights every hour spent in the air should be counted as two does not apply to dedicated PPG canopies For the PPG paragliders warranty covers 24 months 2 years 200 flight hours depending on what comes first For the mountaineering MPG and speedflying wings as well as school and profit users warranty covers 18 months 1 5 year 150 flight hours depending on what comes first WARRANTY DOES NOT COVER canopy colour fading damage caused by chemicals or salt water damag
5. 190 daN colour violet m 1 3 mm strength 140 daN colour green m 1 2 mm strength 90 daN colour blue given colours are subject to slight changes RISERS For the Universal we have chosen four way risers equipped with E ELR Easy Launch Riser system This is an specially marked A riser yellow ribbon ELR m speed system affecting A B and C risers when engaged featuring ball beared pulleys and special line Btrimmers of red tape with right scale designed for RIM quick and easy replacement in case of deterioration E various levels of the pulleys to be used depending on the hangpoint level m ALC allows for effective turns even at high speed tutta without distorting reflex profile too much Steering is done with dedicated handle with red balls fixed on the risers with a magnetic clip prior to the start m TEA Torque Effect Adjuster allowing for REA eliminating the effect of engine torque tending to turn the paraglider in the direction opposite to the propeller s rotation The system can be adjusted to match your specific combination of paramotor propeller For quick and easy recognition in emergency some of the risers are distinguished with coloured band as follows A yellow used for launching A blue used for big ears B red used for B stall D grey needed to keep the glider down in strong wind aborted launch Main A row suspension lines connect to an A riser yell
6. Basic rule of reflex paramotoring says the more turbulent it is the more trims should be released and classic steering should be limited especially with speed system engaged In such moments paraglider is much more effectively steered by TST or ALC systems designed specifically for that reason Problem is illustrated by following drawings Released trims without brakes Typical setting for fast and safe flying Center of pressure of the aerofoil moves forward practically excluding collapses Pitching moment induced by the reflex aerofoil increases angle of attack Released trims with brakes applied Even slight brakes application especially on full speed bar shifts the center of pressure back and due to lack of reflex on trailing edge pitching moment now decreases angle of attack Additionally turbulence behind the wing occurs In some circumstances this can lead to a collapse Using the brakes can be sometimes necessary for heading corrections still you should keep your brakes free when flying ahead otherwise the reflex feature doesn t work Closed trims In this configuration brakes are the normal and prescribed steering system Slow trim is used for launching in nil wind and thermalling The canopy behaves similar to classic profile paragliders with slightly increased tuck resistance x Pitching moment center of pressure Turns executed in this way will be slightly wider but strength needed to initiate the tu
7. low Figure 4 TEA cord inactive a and engaged b a Figure 5 You can reduce drift of the paraglider contrary to propeller rotation with TEA or the additional inner loop in the risers hangpoint visible nearby Bear in mind though that with TEA you can set a knot exactly where it s needed to compensate torque accurately while simple loop does not have any adjustment 7 Universali Figure 6 Steering systems scheme Here is a simple guide to find your way ina maze of risers and their various handles Classic brakes operate along entire trailing edge ALC system is active on the outer parts of the trailing edge and the TEA affects stabilizer only With this arrangement the pilot has full range of steering systems at his disposal and can freely choose between them according to his needs and current situation 38 Figure 7 Trimmers influence on the wing profile Trimmers closed Trimmers in 6 Trimmers fully opened position Minimal speed and Risers of equal length Maximum speed minimal sink Transitional position Take off position neutral configuration neutral configuration neutral configuration risers length risers length risers length A A 460 mm A A D 460mm A A 460 mm B C 465mm shortening mm lengthening mm 70 7045 D C B AA e Universal Figure 8 Trimmer settings influence on speed system action Lengthe
8. most important that the launch and initial climb are performed with a head wind the danger of losing your airspeed while crossing the the wind gradient is greatly reduced Special attention must be paid to trees power lines and other obstacles including the possibility of emerging rotors Paraglider preparation Lay out the paraglider downwind of the power unit with all suspension lines taut and pointing toward center of the power unit The risers are to be laid on the ground Set the trimmers completely closed In conditions faster settings can be advised Make sure that you warm up the engine while standing windward of the wing Stop the engine before clipping in the risers Now have a quick check if m the helmet is on and locked the risers are clipped in the carabiners the trimmers are properly set the ALC handles are fitted to the risers by magnetic lock nothing will get in propeller s way speed system is running without problems m steering lines and handles are free and not twisted m the engine delivers full power m take off area is clear of obstacles and free to use When you are sure everything is OK you can clip in the wing and execute launch as described in paragraph 3 2 1 a From now on you should steer the paraglider facing forward without looking back over your shoulder when the wing is low behind you turning can cause some lines to get in the propeller Still possible fall on your back and damaging the pro
9. which is looped only at the upper end while there is 60 cm left on the lower end for fastening brake handle this means for this line extra 70 cm is needed Length of the steering line is given as for low hangpoints shorter steering lines For upper hangpoints the line is longer by ca 30 cm with lower placing of the handle 19 So ADS CS ADS ee API Q A x o4 a3 2 we BDI b4 63 be bi cP3 cre AA 5 E CDI tai clO 8 c co c4 8 ce el BRDI aci ALC BRE 34 9 RISERS DESIGN AND ACCESSORIES Figure 1 Risers in lower hangopint configuration steering line is led through one pulley only steering line i upper pulley for low hangpoints Si TEA cord TEA lock i swivel i magnetic lock of the ALC handle adjustable Easy Keeper magnet middle and lower pulley locations high hangpoints ALC handle a brake handle trimmer buckle speed plastic trimmer lock system hook trimmer Sheed handle stem ulleys exchangeable pulley trimmer strap additional inner loop carabiner elastic band e Universal Figure 2 Figure 3 Low hangpoint steering line is led High hangpoint steering line is led through a pulley in upper position through a pulley in lower position Magnetic clip is also placed high Magnetic clip is also place
10. To enter a B stall simultaneously pull down both B risers red tape by 10 15 cm The canopy will collapse across the entire span along its B row the airflow over top surface will break and canopy surface will be decreased Forward movement will be almost completely stopped Further pulling B risers is not advised as tests have shown it to increase wing instability If the canopy forms a horseshoe with both wingtips in front of the pilot gently apply both brakes to recover To exit a B stall the risers should be released in a smooth and decisive manner On quick and symmetrical releasing B lines the airflow will be reinstated and the wing will surge forward returning to normal flight In contrast to standard paragliders in case of Universal there is no need to counter this surge with brakes yet another asset of the reflex profile CAUTION See the PARACHUTAL STALL chapter All rapid descent techniques should be practiced in smooth air and only with sufficient altitude only Full stalls and spins are to be avoided as recovery procedures of the extreme manoeuvres since irrespective of paraglider type they may have dangerous consequences BY FAR THE BEST TECHNIQUE IS SAFE AND CORRECT FLYING SO THAT YOU WILL NEVER NEED TO DESCEND RAPIDLY 3 5 AEROBATICS Universal was not designed to do any aerobatics 3 5 1 WING OVER You make a wingover by performing a series of consecutive alternating turns with growing bank angle Too much b
11. low It is not reasonable to let go of the brakes below 100 meters because a possible power unit malfunction may require immediate attention In general never trust your engine as it can stop at any moment Always fly as if it s exactly what it s going to do Unless it is absolutely necessary e g collision avoidance do not execute tight turns against the torque direction Especially when climbing you can easily enter a stall and consequent negative spin Do not fly with tail wind at low altitudes as it pretty much narrows your options Do not wait for the problem to grow any change of engine sound or a vibration can indicate troubles You ll never know until you land and check it out m Be certain of your navigation m Remember that not everyone is fond of your engine noise Do not scare the animals e Universal 3 4 QUICK DESCENT METHODS 3 4 1 BIG EARS In order to get the big ears you have to pull down the outer lines of the A risers distinguished by blue sheath by some 20 50 cm While inducing big ears you should never let the brakes out of your hands After tucking the tips in Universal will continue to fly straight with increased sink rate up to 5 m s You can steer the wing pretty efficiently by weight shifting After releasing lines the paraglider will usually open up on its own or you can assist it with a long stroke of the brakes For the sake of safety the possibility of a parachutal stall it i
12. stretch resistance of the lines The rigging system consists of individual lines looped and stitched at each end The upper level lines start at the attachment points Cascade wise they are joined by twos or threes to middle layer lines These in turn connect by twos or threes to main suspension lines which are attached to the risers with triangular quick links maillons To prevent their slipping off the lines are kept together with a rubber O ring All the maillons are made of corrosion resistant polished 2 stainless steel ensuring excellent strength and durability PEGUET We use only the best quality certified maillons by Peguet Stabilo lines run from the outer suspension points to the maillons through consecutive cascades as well The same story goes for the steering lines They run from the trailing edge through several layers to the main steering lines which are lead through the pulleys connected to the rear risers and then fixed to the brake handles Steering lines do not carry any load Some of the steering lines of the upper level are additionally led through rings sewn into the trailing edge shortening it when the brake is applied so that steering becomes lighter and more effective All the lines are distinguished by colours depending on their strength m 2 3 mm strength 420 daN colour celadon willow green m 1 8 mm strength 280 daN colour red and orange the latter for pulling big ears 1 5 mm strength
13. take off flight or landing Obviously all faults in the material and manufacturing flaws are covered by normal warranty P When handing the paraglider for the repair you have to present a card confirming its AeroCasco status After the repair you will have to cover only the share of cost value of 50 euro AeroCasco is valid for one repair only There is a possibility to extend AeroCasco for one more year To do this you have to send your paraglider for inspection not later than a year after the date of purchase Extension fee is 75 euro incl inspection Remember to attach the AeroCasco confirmation on expedition AeroCasco does not apply to any of the following theft colour fading damage caused by incorrect storage or transport damage caused by chemicals salt water and force majeure 7 Universal 7 WHAT HAVE YOU BOUGHT The Dudek paraglider that you bought should have the following items the paraglider itself canopy lines and risers transport bag with compression strap Duralight backpack FastBag quick pack a speed system with Easy Catch bar a windsock a pocket with paper work and repair wallet including A piece of self adhesive fabric 10 cm x 37 5 cm for small repairs Note that even small tears located in the vicinity of stitches have to be repaired by an authorised service A looped and stitched suspension line longer than the longest line used in the paraglider that is to be used as
14. A system present making possible to counter the torque in case there is no cross bracing To make TEA work properly you should assembly the line on proper side as of propeller direction and adjust the blocking knot accordingly to torque force When climbing steeply with slow trim settings and high power output beware of the possibility of stall Due to typical PPG feature considerable vertical distance between thrust axis and wing chord the range of safe power operation is closely connected to your skills and equipment Power unit induced oscillations Certain configurations of engine weight output and propeller diameter can cause serious oscillations during which the pilot is being lifted to one side by the torque effect swings down due to his weight then is lifted again and so on To avoid this you can m change the throttle setting and or m adjust the cross bracing to counteract the torque if there is one present and or m use the TEA pulling down the knot through the tube simultaneously blocking it in the slit and or m shift yourself to the other side of the harness and or m change the trimmer setting The best method is to fasten opposite cross bracing or apply some weight shift Such oscillations usually occur at full power the greater the engine output and propeller diameter the bigger the swings In addition there are often e Universal too late or wrong pilot reactions increasing the problem instead of sol
15. Nevertheless once you have mastered these additional assets flying will become pure fun Good handling will let you make best use of thermals and increased speed on transitions means that your presence in sinking air will be shorter To avoid stalls when braking with closed trimmers their movement is restricted by the tape sewing Note it is possible to push the sewn tape through the buckle with both hands to replace it but normal operation range is restricted by said place TURNS Universal is an agile wing with smooth reactions to the steering inputs Handling is actually easy and forces grow proportionally to position of the brakes Adding some weight shift will make the paraglider turn really quick and tight The combined technique weight shifting and brake input is by far the most efficient method Turn radius is determined by the amount of inside brake used and weight shift Additional application a little outside brake after initiating the turn with maximum weight shift increases turn efficiency and the outboard wing s resistance to collapse in turbulence the edge of a thermal etc In case of necessary turning in confined area at slow speed e g slope soaring it is recommended to steer the decelerated canopy by loosening the brake at the outside of the turn while applying just a little more brake on the inside NOTE when entering a turbulent area you should brake a little to put up the tension It will allow you to re
16. a temporary replacement Do not cut it if you have to replace a shorter line just tie it at the length needed A paraglider passport with entered date of purchase and valid technical inspection please check the serial number with the sticker on the wing tip The User Manual you are reading Small gifts SUMMARY If you respect the rules of safe flying and proper glider care you will enjoy many years of pleasant airtime Still you must be aware of possible dangers and face them wisely You must accept the fact that all air sports are potentially dangerous and your actual safety depends solely on you We insist that you fly safely and this concerns both the weather choice and safety margin during all manoeuvres FLYING THE PARAGLIDER IS ALWAYS YOUR OWN RESPONSIBILITY SEE YOU IN THE AIR 8 RIGGING TABLES AND SCHEME The rigging scheme itself is published on the next page while tables of line lengths you will find on our website www dudek eu Lengths are measured with a specialised computer operated device All lines are stretched with a 5 kg load before cutting Thanks to the abovementioned device and proper procedures final tolerance of line lengths does not exceed 0 15 NOTE Distances given below are to be understood as distances between connection points When cutting a line for repair 20 cm extra must be added as at each end a 10 cm stitch is required to fix the loop The only exception is the main steering line BRP
17. a tuck one of the stabilisers may tangle in the lines Usually a couple of pulls with a brake settles the matter If it s not enough try to untangle it with big ears or a stronger pull on the risers In case of any doubts you should seriously consider a rescue chute It is there as a normal equipment part not just an ornament 3 6 6 EMERGENCY STEERING In case of any malfunction that renders normal steering impossible you can safely steer and land Universal using the D risers grey marking or stabilo lines 4 PARAGLIDER CARE Proper looking after your paraglider will prolong life of your Universal 4 1 FOLDING AND STORAGE Universal features a number of recent technologies like tensioning the leading edge with a plastic string That s why the paraglider should be folded with care in order to keep it healthy during transport and storage Basic rules to be observed when folding 1 We fold the canopy together on rib to rib cell to cell basis like a harmonium We don t break the wing in halves taking the stabilizers towards centre 2 After creating a package along the maximum chord we don t roll it but fold two to three times depending on the chord length from trailing to the leading edge 3 Leadin edge stays on top of the folded canopy Store the paraglider in a dry place away from chemicals and UV exposure Never pack or store the glider when wet Remember that the wing becomes damp also while lying on green grass in di
18. ace in the vicinity of the leading edge Their exact placement was very carefully selected so that they got maximum ram effect in as many flight situations as possible On the wingtips we placed the ACS Auto Cleaning Slots dedicated slots automatically removing dirt from inside the wing Asto Cleaning Slatu Careful selection of modern fabrics and design solutions brings about great strength and durability of the Universal All materials used come from marked production batches and each production step can be verified down to identification of specific worker and controller Universal is manufactured under new technology utilizing precision of the laser cutter All stages of production process take place in Poland under strict supervision of the designer himself thus ensuring highest European quality e Universal Fabric E The upper surface is made of 41 gram Dominico DOMINICO Tex cloth Lower surface is made of 34 gram Dominico Tex cloth contributing to low weight of the canopy The ribs must be as rigid and stretch porche resistant as possible We found these qualities in Dominico 41 Hard cloth All suspension points and leading edge reinforcements are made of Porcher SR Scrim fabric Rigging system All of the Universal suspension lines are sheathed Tech nora e by a coloured polyester layer which is covering a brownish Technora core Low number of lines required such composition featuring high strength and
19. ach if anything goes wrong Still if you forget to switch off the ignition before the wing falls down there is a considerable risk of damaging propeller catching lines in it or even suffering injuries connected with falling on your running engine Remember m Whenever possible get to know the landing field before taking off Check the wind direction before planning the approach Landing with power off requires much less space m Incase of any doubt practice the landing until you feel totally safe 3 3 4 GOLDEN RULES m Never place the power unit downwind of the paraglider m Check double check and then check once again if there is no fuel leakage m Do you have enough fuel for the flight It is always better to have toomuch than too little Check if there is nothing loose in the harness that could possibly contact the propeller in flight Whenever you encounter a problem fix it AT ONCE however small it is Always put on and lock the helmet before getting in the harness Before each launch run a full pre flight inspection After landing control the wing facing the direction of flight as on turning you always risk getting lines in the propeller Turn only if there is danger of falling on your back Do not ask for trouble do not fly over water between trees or power lines and other places where engine failure will leave you helpless Mind the turbulence caused by other gliders or even by yourself especially when flying
20. act instantly in case of a problem CAUTION Too hard or too quick pulling of one brake can cause the wing to enter a spin THERMALLING AND SOARING When flying the Universal minimum sink is reached with slight brake pressure applied 10 to 15 cm depending on pilot s weight In turbulent conditions the canopy should be flown with a small amount of brake applied This improves overall stability by increasing the angle of attack of the canopy The canopy should neither rock back nor surge forwards but always stay above the pilot In order to achieve it the pilot should accelerate the canopy by letting off the brakes when entering a thermal according to its strength and brake it on exiting This is part of basic active flying that can spare you many potential collapses When soaring the slope minimum height of 50 m above the ground is recommended for safety reasons It is important to comply with air traffic rules especially when many pilots share airspace close to the hill The avoidance manoeuvres often happen to be impossible in such conditions FLYING WITH SPEED SYSTEM ENGAGED When flying into head wind or through sink it is advisable for the sake of best glide angle to increase speed as long as conditions are not too turbulent Full application of the speed system increases flight speed by some 30 In contrast to most paragliders it does not decrease wing stability in fact the Universal seems to counter the turbulences ev
21. actically impossible especially at higher speeds During tests we succeeded in creating this situation only with fully closed trimmers and using special measures Such forced collapses can lead to extremely deep collapses so recovery will require decisive pilot action short and equal application of both brakes 3 6 3 FULL STALL AND NEGATIVE SPIN Practically do not occur may happen only as a result of serious neglect or intentional action of the pilot You have to be careful when flying at low speeds until fully familiar with brake operation Wing recovers spontaneously in initial phase of stall otherwise use standard procedures 3 6 4 DEEP STALL Under normal conditions does not occur If you want to prevent it happen at all simply stick to a couple of rules m after B stall release the risers quickly and evenly Don t be afraid Universal does not jump forward excessively B after big ears execution engage the speed system This will increase both the sink rate and safety margin as big ears constitute an aerodynamic brake with significant loss speed Nevertheless if such a parachutal stall happens e g due to strong turbulence simply apply some pressure on speed bar and or push the A risers forward You can release the trims too 3 6 5 LINE OVER AND CRAVATTE Universal is a modern wing which in order to decrease drag has fewer suspension lines and greater distances between them Therefore it s always possible that after
22. anking connected with some flaws in co ordination and execution can evoke pretty dynamic collapse CAUTION Steep turn with bank angle over 60 degrees is a prohibited aerobatic manoeuvre 3 6 EXTREME MANOEUVRES CAUTION EXTREME FLYING MANOEUVRES SHOULD ONLY BE CARRIED OUT DURING SAFETY TRAINING COURSES SIV INSTABILITY TRAINING UNDER PROPER GUIDANCE WHILE PROVOKING OR EXITING REAL SITUATIONS THERE IS DANGER THAT YOUR ACTIONS WILL PROVE TOO QUICK OR TOO STRONG SO YOU SHOULD ALWAYS EMPLOY GOOD JUDGMENT STAY CALM AND TAKE MEASURED ACTIONS Since all actions required to exit or prevent dangerous situations on Universal are typical and pilots flying this wing should already have proper experience we are going to describe only the characteristic features of the Universal Description of standard methods dealing with extreme situations can be found in textbooks 3 6 1 ONE SIDED COLLAPSE Even when the trimmers are fully opened or the speed system is engaged collapses practically do not occur and can be induced only by a very strong turbulence Still if it happens a little counter steering is enough to keep the Universal on course Under normal conditions with collapses up to 50 of the e Universal wingspan Universal will reinflate instantly and spontaneously If it will not happen you should aid this process by application of brake on the collapsed side 3 6 2 FRONTAL COLLAPSE The reflex profile of the Universal makes it pr
23. ard launch turn back to face the wing moving one riser group over your head As a consequence you will have the risers crossed Unclip the brake handles from rear risers and grip it outside of the risers without crossing your arms In this way you steer the right side with you left hand and left side with your right hand Now take corresponding A risers on both sides still keeping brake handles in your hands Make sure that the wing inflates symmetrically and the lines are not tangled Building up tension with a few steps back and simultaneously lifting the A risers do not pull them towards you will make the paraglider rise When it arrives over your head stabilize it with the brakes check again if all lines are clear and the cells inflated When turning into wind remember to turn the right way hint always do it the same direction and to keep the lines taut loaded at all times The turn itself should be quick and smooth After turning check if the canopy is correctly inflated lines and brakes are free amp there is free space to launch off you go running into wind with light braking when taking off CAUTION when deflating the canopy in strong winds e g aborting a launch use the D risers not the brakes Using the brakes in strong wind can lift the pilot up and drag him her back e Universal 3 2 2 FLIGHT The increased speed range of Universal in case of trimmers operation may demand some attention in flight
24. ch harness your typical steering range will be different PRE FLIGHT CHECK A thorough pre flight check is essential for any aircraft and the Universal is no exception Having unpacked and laid out the paraglider in a horseshoe directed against wthe wind following checks must be made m canopy lines and risers condition Do not launch if the slightest damage is noticed m the paraglider should be arranged so that the centre section A lines yellow risers will strain earlier that the outer ones blue risers This ensures easy and symmetrical launch m cells of the center section must be handled with special care so that leading edge stays taut and even m all lines and risers should be separated Make sure they are not tangled and pay special attention to the A lines which should run free from the A yellow band and A risers blue band to the canopy m itis equally important to untangle the brake lines so that they will not catch anything on the ground during launch They must be firmly attached to the brake handles and run freely through the pulleys to the trailing edge m make sure the risers are not twisted m itis very important to check that no lines are looped around the canopy The so called line over may have disastrous consequences during take off Always put on and fasten your helmet before clipping in to the harness Check quick links maillons Sometimes they can unscrew especially when the wing is new
25. cts Easy Kooper against twisting f half rigid rigid plastic rod y PVC tube Pa slit of the rod Z The most soft handle is obtained when no insertion is used exchangeable insert Addressing different needs of our clients we have created a TCT system Triple Comfort Toggle making it possible to have your brake handles in rigid half rigid or soft configuration without need to purchase additional handles Easy Keeper DEK Main Steering Handle TCT swivel Easy Keeper TCT Easy Keeper is our indigenous way to hold the brake handles atthe risers by using strong neodymium magnets It keeps the handles firmly at the risers while both attaching and releasing goes smoothly and easily The system allows for easy placing the brake handles on risers during flight when they are not used thus minimalizing danger of getting them into running propeller Especially in turbulent air use only the ALC system usage of the main brakes considerably increases possibility of collapses ATTA WHICH HARNESS You can use any certified harness with hang point between 35 cm and 49 cm from the seat the safest distance being 40 cm Width between carabiners should be somewhere between 37 cm and 45 cm still in this case the best option is 40 cm too Please note that any modification of seat hang point distance changes the position of the brakes in relation to the pilot s body You must remember that in ea
26. e best effect Good knowledge of weather conditions e g wind at different altitudes and smart use of thermals or dynamic lift will help you greatly reduce fuel consumption and increase flight range Of course the engine is always there to bring you in the right place Do not hesitate to lead the Universal into tight thermalling in order to win some altitude and spare fuel In order to make the best of the thermal completely close the trimmers Trimmers and speed system operation The reflex wing airfoil enables the Universal pilot to use a wide range of trimmers and speed system action You are free to experiment with all possible settings as long as you are on safe altitude Fully opened trimmers increase the speed and stability of the wing and with it also its ability to cope with turbulences and overall penetration As forces on the brakes grow at high speeds the weightshifting or steering with ALC system becomes increasingly effective ALC system can be used in all trimmers and speed system settings also in combination with main steering handles when trimmeri is closed At maximum speedbar and or fully opened trims we strongly recommend steering with ALC system or TEA system especially in rough air Influence of classic steering on the reflex profile Pilots used to classic paragliders tend to fly active style with their brakes constantly tensioned Flying a reflex wing like that is ineffective and can possibly be dangerous
27. e caused by incorrect use damage caused by emergency situations damage resulting from accidents airborne or not WARRANTY IS ONLY VALID IF flight hours are correctly registered in the logbook of the owner and possible earlier owners distinctly marking PPG flights the paraglider is handled in accordance with the operating manual the purchaser has not carried out any repair by him herself excl minor repairs with self adhesive patches carried out any modifications the paraglider can be unmistakably identified the paraglider was being inspected according to prescribed timetable If you have ought your paraglider second hand ask its previous owner of the paraglider for a logbooks copy total of flying hours since the date of first purchase AEROCASCO Normal warranty does not cover repairs of damages caused by the user or a third party As costs of such repairs can be considerable Dudek Paragliders offer an AeroCasco insurance It covers a one off repair of any mechanical damage no matter how big and whoever inflicted them The only expenses the purchaser has to pay are shipping costs and so called share of cost amount AeroCasco can be purchased only for a brand new paraglider at the paraglider purchase Its cost is 50 euro NOTE AeroCasco is not available for all paragliders check this before purchase It can be obtained for privately used wings only AeroCasco applies only to damages that took place during
28. ed an effect of inverting the profile when trailing edge is being pulled down emerges pulling the brakes see page 20 That effect can cause dynamic collapses especially at full speed The safest way to change your course at high speeds is to use the TEA lines or in the order of safety the ALC handles Any steering inputs should be smooth and easy without sharp and or deep movements Such actions can dynamically change pressure distribution over the airfoil leading to collapses These warnings affect every paraglider and Universal is no exception TABLE OF CONTENTS Page 1 Introduction iiiiiin 2 3 2 1 Design 2 2 Structure 3 Flight operato 8 3 1 Steering lines and speed system adjustment 3 2 Free flying 3 2 1 Take offt 3 2 2 Flight 3 2 3 Landing 9 2 4 Winching 3 3 Powered flights 3 3 1 Take off 3 3 2 Flight 3 3 3 Landing 3 3 4 Golden rules 3 4 Quick descent methods 3 4 1 Big ears 3 4 2 Spiral dive 3 4 3 B stall 3 5 Aerobatics 3 5 1 Wing over 3 6 Extreme manoeuvrese 3 6 1 One sided collapse 3 6 2 Frontal collapse 3 6 3 Full stall and negative spin 3 6 4 Deep stall 3 6 5 Line over and cravatte 3 6 6 Emergency steering 4 Paraglider 8 6 27 4 1 Packing amp Storage 4 2 Cleaning 4 3 Repair 4 4 Deterioration a few tips 5 Techn
29. en better Still if you meet some serious trouble it is advisable to release the speedbar With application of the speed system the brake forces increase and brake effectiveness decreases At maximum speedbar and fully opened trims we strongly recommend steering with ALC system or TEA lines Turns executed in this way will be slightly wider but strength needed to initiate the turn will be smaller and there will be no decrease in speed 3 2 3 LANDING The Universal is easy to land Just make sure that last turn into the wind is done with sufficient altitude since prior to touch down you should build up speed fully releasing the brakes Then flare out at 1 meters over ground by gently braking The glider may climb again for a while gaining some height if too much brake is used When landing n strong wind you can partly release the trimmers in order to have better forward speed Strong wind landings hardly require braking if any at all Use D risers coloured grey to deflate the canopy after landing Using the brakes will probably result in pilot being lifted and dragged backwards The final glide of the landing approach should be straight and smooth Steep or alternating turns can result in a dangerous pendulum effect near the ground 3 2 4 WINCHING A lot of successful winches on Universal have been made Experience shows that it can be done but proper attention must be paid CAUTION During start especially winched or w
30. er hangpoint and adjust them to your preferences if necessary For free flying you shouls fix the pulley on the end of the extending loop placed at the upper hangpoints and the steering handles on upper positions marked on the steering lines so that steering lines are effectively shortened This is the factory setting of the paraglider unless ordered otherwise See adjusting the pulley and steering line marks according to the hangpoints on p 36 Generally speaking upper hangpoints require longer steering lines while the lower hangpoints shorter lines Before you will take on powered flight it is recommended to try the setup out Hang up the entire PPG unit with ropes sit in the harness and have someone pull up the risers You must make sure that in flight you will always be able to reach the brake handles even if the airflow blows them away Being suspended in this way you have a perfect opportunity to adjust the speed system too The speedbar should not be pulling pull its lines nor risers when not applied Neither should it be too loose for it could catch the propeller An additional way to check the whole configuration out is to visit the take off site in steady winds of 3 4 m s With the engine off inflate the wing and take it up over your head When it stabilises check that the brakes are loose and do not pull the trailing edge There should be a spare inch or so before they activate Remember that it is always safer to se
31. hecklist After warming up the engine put the power unit on turn to face the wing go to the risers and clip them in the appropriate carabiners Pulling on the front and rear risers open the cells It is a good idea to pull up the wing briefly in order to check that the lines are not tangled Holding the risers brakes and throttle as described above pull the front risers and raise the canopy over your head On most occasions you won t have have to brake it especially if the trimmers are partly released Perhaps it does not agree with your experience but in this trimmer setting Universal s reflex profile stabilizes the wing and does not allow it to surge forward Once you have it overhead turn around open the throttle and take off As with the classic launch in this case too you have to find such combination of trimmers brakes and throttle settings that will give you the best speed and rate of climb Remember m You are launching with your hands crossed You have to really master this technique before trying it with a running engine on your back m Any brake operation or steering inputs in general should be smooth and gentle m Do not try to take off until you have your wing overhead Hitting the gas pedal before that can cause dangerous oscillations m Do not sit in the harness until you are sure you are flying m The faster the trim setting is the more brake input is required to take off When clipping in the crossed riser
32. ical rr 29 6 Warranty AeroC SCO 30 7 What have you bought 32 8 Rigging tables and scheme ia 33 9 Risers design and accessories ssi 35 7 Universal 1 INTRODUCTION CONGRATULATIONS We are pleased to welcome you among the growing number of DUDEK PARAGLIDERS pilots You ve become a proud owner of recreational state of the art paraglider built according to recent trends in both free flying and paramotor wings Extensive development application of the most modern methods and thorough testing resulted in a friendly behaving paraglider offering the pilot a lot of fun combined with great performance We wish you many enjoyable and safe flying hours DISCLAIMER Please read this Manual carefully and note following details The purpose of this Manual is to offer guidelines to the pilot using the paraglider and it is by no means intended to be used as a training manual for this or any other paraglider You may only fly a paraglider when qualified to do so or when undergoing training at an accredited School or with an Instructor Pilots are personally responsible for their own safety and their paraglider s airworthiness The use of this paraglider is solely at the user s own risk Neither the manufacturer nor dealer do accept any liability connected with this activity This paraglider on delivery meets all the requirements of the EN 926 1 and 926 2 regulations or has an airwor
33. is pretty agile nicely handling and safe Important for instructors Universal is perfect for initial PPG training 2 1 DESIGN Exceptional versatility of the Universal is a result of its genesis The wing was born as a byproduct of the Synthesis2 development process One of the paths we ve been following was creation of a relatively simple paramotor wing featuring better economy agility easy launch and low power demand Some of the prototypes did not stood up to legendary stability of the original Synthesis but demonstrated many other valuable traits we did not like to drop So we ve explored that path employing both our long time experience and state of the art technologies Universal was built according to a new idea That idea alleges bigger increase in speed realized mainly with the trimmers adapting their travel to individual pilot s skills and experience as well as limited reflex capability in lower part of operation so that the airfoil acquires shapes similar to those used in our modern highly efficient free flying paraglider types That idea is augmented by many recent solutions such as FET technology keeping the desired shape of the leading edge during launch and flight resulting in Universal s excellent launch performance even in no wind e Universal Another novelty is the ALC new version of the ALC steering system allowing safe and effective steering at fast trimmer settings withot using main brakes Additiona
34. ith a motor always remember to bring the wing directly over your head The aerofoil and its angle of attack were arranged so as to give maximum lift coefficient with relatively high safety e Universal level As a result it can stay behind a pilot if he neglects bringing it directly over head during launch 3 3 POWERED FLIGHTS NOTE Before each start it is necessary to have a thorough check of the paraglider harness and power unit In powered flight most of the wing characteristics remain as described above chapter 3 2 Still there is additional information needed concerning power output proper matching of the wing engine propeller etc Dudek Paragliders cannot take responsibility for all possible combinations but if you contact us we are always ready to help First flights In order to get familiar with your wing we recommend flying with closed trimmers first because in this configuration Universal behaves like a classic paraglider Flying like that try pulling the brakes some until you feel resistance usually it will be at about 1 4 of the brake travel Once you feel confident with your wing you can start experimenting with faster trim settings and speed system Learn to use all of the additional speed and safety of the Universal 3 3 1 TAKE OFF Classic launch with no wind Even when it seems that there is no wind at all it is rarely so Therefore always be careful in determining the conditions since in PPG flying it is
35. l improvement is possibility to fix the system to the risers with magnetic clips so that in will not get tangled Ideally the system should be installed only when the pilot graduates to use the other faster half of the trimmers Our factory installed TEA system allows for controlling the flight direction at any time with any speed so far this is the safest way to preserve or change the flight direction at high speeds Even as the Universal was designed in order to keep all features of the classic paraglider application of the reflex aerofoil adds more beneficiary traits First of all using that profile means that the wing stability does not depend exclusively on the pilot It maintains a stable pitch attitude rising and falling through thermals while remaining stable above your head without need for so much pilot input Generally speaking the reflex profile is a special kind of aerofoil section The specific static pressure distribution creates a situation where at low attack angles only the wing fore part some 60 of the chord is producing lift while the rear 40 of the chord creates an effective stabiliser against excessive decrease of the attack angle The trimmer system allows for considerable raising the rear part of the airfoil thus effectively reducing its projected chord and surface area by some 30 giving the paraglider a higher wing loading and increasing its speed The centre of pressure also moves forward adding enhanced
36. le of the Universal will keep the wing level so after opening the throttle you ll start to descend with increased speed instead of climbing 3 3 3 LANDING In PPG flying there are two kinds of landing with and without power Power off landing At an altitude of 50 metres switch the engine off and glide as you would on a conventional paraglider lt reduces the chances of damaging the propeller on landing but on the other hand there is only one attempt possible so it has to be done right With or without power Universal better copes with turbulence on partly open trimmers i e some 6 cm position 6 So if the conditions are rough better make an approach with greater speed plan a lot of free space as for a hangglider and wear that speed off before touching down Universal preserves the energy well so there is a long float necessary exchanging the abundant speed for lift with your brakes If the landing field is not big enough and you have to land on the spot we advise you to set the trimmers in slower settings It will increase lift coefficient of the wing effectively decreasing its sink rate and speed Such an action is especially important when flying with high surface loading Powered landing Make a flat approach with the engine idling then level out and lose the speed before final flare Immediately after touchdown switch off the engine The main advantage of this procedure is of course the possibility of a repeated appro
37. lean since getting dust in the lines and fabric will reduce their durability Be careful to keep snow sand or stones from entering the cell openings their weight can slow or even stall the glider and sharp edges can damage the cloth Prevent lines from catching anything as they can overstretch or tear Do not step on the lines Uncontrolled strong wind takeoffs or landings can result in the leading edge of the canopy hitting the ground hard which may seriously damage the ribs sewing and surface material Knots can chafe suspension and or brake lines Check line lengths after tree or water landings as they can stretch or shrink A line plan is included in this manual or may be obtained from the dealer when needed After landing in water you should check the wing fabric as well since the wave forces can cause the fabric to distort in some areas When taking the wing out of the water always do this by trailing edge so that water can flow out freely After a sea landing rinse the paraglider with fresh water Since salt crystals can weaken the suspension lines even after rinsing in fresh water you should replace the lines with new ones immediately after contact with salt water Every second year Universal should undergo technical inspection by the manufacturer or authorised distributor USER MANUAL 5 TECHNICAL DATA 7 Surface area projected m7 projected m Distance pilot to wing m
38. manual DUK www dudek eu paragliders NOTE Please read this manual carefully before your first flight Very important Before use it is vital to check in which configuration the steering lines and pulleys are currently set lower or upper hangpoints and adjust them to your preferences if necessary The risers have three points to fix the pulleys on lengthened upper lower and middle one see risers on page 35 On each main steering line there are three points marked lower upper and middle one to fix the steering handle according to position of the pulley Steering lines must not not push down the trailing edge when not operated this must be observed in all possible configurations of trimmers and speed system Steering lines must have a couple of centimeters play before they engage affect the canopy see section 3 1 on the proper adjustment For sake of safety it is always recommended to set the brakes rather too loose than too tight Make sure they are set symmetrically too Ill adjusted steering lines may cause you to misinterpret the canopy s behaviour in flight and in case of encountering turbulence in accelerated flight dangerous collapses may occur see page 20 When flying at full speed trimmers opened trimmers opened and speedbar pushed especially in uneasy air it is highly recommended to steer the paraglider using alternative steering methods like TEA or ALC only With increasing spe
39. ning and shortening values are given in respect to neutral risers length 460 mm Full acceleration with closed trimmers Full acceleration with opened trimmers good speed easy steering decreased small angle of attack maximum speed stability Classic speed system action Great stability and hard steering Advised use of ALC system or TEA shortening mm lengthening mm shortening mm 65 70 75 oA 130 50 30 80 bh rad A Trimmer operation tips SLOW FAST Trimmer strap ma closed released bi I MODIFIED FULL REFLEX I REFLEX AIRFOIL AIRFOILI Launch I I I Brakes ALC TEA a TST I Torque effect adjuster can be used for correcting flight direction in fast configurations too trimmers speed system It works the same way as the TST used in our older paragliders Main brakes and the ALC can be used both simultaneously and or alternatively The brakes will be more effective at slow settings while the ALC at faster ones Thermalling is most effective at closed trimmers In case of strong turbulence it is advisable to partly open the trims thus increasing overall stability In nil wind conditions the launch is easiest at completely closed trims The stronger the wind the more you can open the trimmers Nevertheless launch on fast trim settings will be hard or outright impossible depending on wind speed 42 Fot lwona Dudek DUDEK paragliders
40. ow and A blue B row and stabiliser lines go to B riser red C lines go to C riser black neoprene and D lines to D riser grey as well as steering lines through their pulleys Brake handles are attached to the steering lines at optimal point guaranteeing safe and effective operation On the main brake line there are three points marked high low and middle to be used depending on the harness hangpoint level On adjusting the steering lines see chapter 3 1 Our newest brake handle used in Universal besides its attractive light design features m a swivel preventing possible twisting of the steering line Trigo Cadore Taggia m TCT Triple Comfort Toggle system m EK Easy Keeper system see further pages DEK Lory keepo e Universal 3 FLIGHT OPERATION 31 STEERING LINES AND SPEED SYSTEM ADJ USTMENT We strongly advise following actions to be supported by an instructor or at least an experienced pilot The Universal risers are shorter than in most paragliders thus alleviating potential problem with different hangpoints There are three places to fix the steering lines pulley lengthened upper lower and middle see risers diagram on p 36 On the main steering line there are three points marked as well higher lower and middle one indicating where to fix steering handle depending on pulley placement CAUTION Before first use check whether steering lines and pulleys are set for higher or low
41. peller is dangerous and costly so it should be avoided at any price even that of some damaged lines During take off when you feel the strain on both risers to be equal make sure the canopy is overhead open up full power and lean back to counter the engine thrust so that it can push you forward rather than towards the ground The best option is not to use the brakes allowing the paraglider to rise as it was laid out If it starts to swerve from its course just pull the opposite riser and run under the centre of the wing while preserving starting direction If the wind suddenly drops give a stronger pull on the risers If the paraglider falls to one side or back too far to be lifted again kill the engine interrupt launch and check the conditions once again As the wing rises the forces grow lighter and it should stabilise above your head without overshooting This is the best moment to check if it is inflated well and the lines are not tangled but do so neither stopping nor turning Once you feel the forces on the risers decrease run faster and let go of the risers See if there is already any opposition on the brakes and if necessary use them to correct direction or to increase lift at take off Remember m Ifthe cage of your power unit is not stiff enough the risers strained during launch can deform it to the extent of collision with the propeller Before giving it full power see that the cage does not catch any lines m An
42. pitch stability Such a shift of loading gives the Universal an exceptional tuck resistance and increases its projected aspect ratio resulting resulting in much better performance especially at high speeds When greater lift is needed you close the trimmers thus modifying canopy to get airfoil operating on its entire chord The result of our work is a 100 reflex paramotor paraglider with perfect performance exemplary safety and steering characteristics of classic paragliders We proudly present you with the exceptional Universal paraglider suitable for the beginner and recreational pilots whether free of paramotor flying 2 2 STRUCTURE The Universal 3D body was designed in our CSG Canopy EN Shape Guard system comprising many elements resulting CSG in exceptional coherence and stability of the shape Below you will find a short description of CSG subsystems np Shape Guard Universal has an elliptical planform with slightly rearward swept tips The cells are divided with ribs additionally supported by diagonal VSS V shaped supports system Such arrangement ensures a smooth top surface exact aerofoil reproduction across the entire wingspan and yet more importantly minimal number of suspension points The lower surface has a RSS Reinforcing Strap System applied in the wing s interior RSS is an ballooning independent reinforcements system made entirely of paragliding fabric stiffening and stabilizing entire canopy structure
43. rect sunlight A good precaution to avoid dampness and or UV when you have to wait in a start queue is to use quick pack after rigging up Always dry the glider thoroughly before packing and or storage Never pack you paraglider too tightly While drying never expose your paraglider to direct sunlight operation Please note that with frequent kiting groundhandling exercises your paraglider will deteriorate faster due to its repeated rising falling and being dragged on the ground 4 2 CLEANING Clean the paraglider with water and a soft sponge Do not use any chemicals or alcohol as these can permanently damage the fabric 4 3 REPAIRS Repairs should only be carried out by the manufacturer authorised distributor or authorised workshop It is acceptable to fix minor cloth damage with the self adhesive patches included in the package 4 4 DETERIORATION A FEW TIPS The Dudek Universal is made mainly of nylon a fabric which like any other synthetic material deteriorates through excessive exposure to UV rays that come with the sunlight Hence it is recommended to reduce UV exposure to a minimum by keeping the paraglider packed away when not in use Even when packed in a bag it should not remain in the sun for long 7 Universal Universal suspension lines consist of Technora inner core and polyester sheath Submitting them to excessive loads in flight should be avoided as it can cause irreversible damage Keep the paraglider c
44. rn will be smaller and there will be no decrease in speed Please note the wide operational speed envelope of the Universal achieved by trimmers only Due to such wide range we ve decided to introduce capability of restricting that range before the launch by the pilot according to his skills and preferences Even when the trimmer range is restricted by half applying the speedbar in urgent needs allows for almost maximum speed Restricting the trimmer range is shown in Adjusting the trimmers appendix in this manual At slower trimer settings both the sink and steering forces decrease so it is possible to efficiently use the thermals Study drawings of trimmers and speed system adjusting and setting as well as their influence on the wing shape e Universal When flying in slow configuration turns can be much tightened and more effective by means of differential brake operation Slight use of the outer brake with considerable amount of the inner one will diminish the loss of lift in turn Turns can be much improved by additional use of throttle speed system etc Once with growing experience you will master these techniques you will be able to execute fully coordinated and effective turns bringing to mind the aeroplane handling REMEMBER m Trimmer setting is another part of the pre start check list m If it will be asymmetric the wing will be turning all the time And if you will inadvertently set them off the reflex profi
45. s you can find proper connection of the speed system particularly hard Be careful not to confuse the risers Climbing Once you took off safely continue heading against the wind using brakes to correct rate of climb Do not try to climb too steeply attempts to increase climb rate by pulling the brakes will have an adverse effect due to the additional drag actual rate of climb will worsen and with the throttle fully opened open even a stall can happen In powered flight the Universal behaves more like an aeroplane than a paraglider and it is good idea to regard it as such If there are no obstacles present it is by far safer and more impressive for the spectators to fly level for a while after take off and gain some speed before converting it to height with a brief pull on the brakes Another reason not to try climbing too steeply is the risk connected with engine failure at low altitude Even as Universal in a steep climb does not stay behind as much as conventional paragliders do the low speed is more likely to cause a stall Besides you should always be able to land safely in case of engine malfunction so it s better not to take unnecessary chances and always fly with a safe margin of speed Depending on the power unit geometry it is possible that after take off you will notice a propeller torque turning moment It will try to turn you around so be counter steer it with a brake or harness cross bracing In Universal there is our TE
46. s reasonable to engage speed system after pulling big ears in order to lessen the angle of attack of the wing centre Executing big ears with opened trimmers is very difficult due to reflex profile stabilisation CAUTION See the PARACHUTAL STALL chapter Never try to pull big ears during powered climb as the increased drag can lead to increase of the angle of attack and a parachutal stall Besides pulling the ears while climbing is pointless anyway 3 4 2 SPIRAL DIVE Universal is a very agile paraglider so entering spiral dive happens very quickly and can be surprising for the less experienced pilot A spiral dive is characterised by reaching the highest sink rates possible Significant G forces however make it difficult to sustain a spiral dive for long as will place high loads on both pilot and glider to degree of losing consciousness by the pilot Never do this manoeuvre in turbulence or at too high bank angles Control the dive and do not exceed 16 m s sink If the dive is not stopping after releasing the brake assist the glider with the outer one NEVER DO BIG EARS IN A SPIRAL In this manoeuvre smaller number of lines is carrying an excessive load mulitplied by the centrifugal force what can lead to damage of the lines or even the paraglider itself load of a single line can be much higher than passed in certification trials i e 8 G 3 4 3 B STALL B stall can be executed only with fully closed trimmers i e pos 0
47. t the margin of play too big than too small And most importantly the setting must always be symmetrical 3 2 FREE FLYING The main difference between the Universal and other paragliders is that due to its increased tuck resistance both during launch and flight and greater speed range when using the trimmers it can be safely flown in strong conditions too DAL Steering System ALC allows for aggressive tums even on full speed without modifications of the reflex profile This is of special importance when flying in turbulences with open trimmer and speed system engaged Additionaly it is important for bigger canopy sizes without special solutions demonstrating problems associated with big steering forces and low agility The steering handle here is the red ball easily adjusted to match personal preferences TEA Torque Effect Adjuster Magnetic lock of the ALC handle three pulley locations line i _ gt handle with ball elastic band Two examples how to handle ALC DAL Steering System Using the magnetic lock of the ALC handle Easy Catch Easy Catch speedbar is a godsend for those who have problems catching the bar after taking off The speedbar is designed to stay always in front of the speedsystem lines Its finish is very robust so long term service is guaranteed Triple Comfort Toggle Triple Comfort Toggles Neodymium magnet of the awivel prote
48. thiness certificate issued by the manufacturer Any alterations to the paraglider will render its certificates invalid NOTE Dudek Paragliders warns that due to constant process of development the actual paraglider may differ slightly from the one described in the manual 2 WING For whom Universal Universal us the first paraglider ever to smoothly and efficiently merge two aspects nicely hadling free flying paraglider with EN B certificate full blood paramotor canopy conforming to DGAC standard Universal is dedicated for beginner and recreational pilots who fly exclusively free but want to benefit from moderate reflex ability mostly free sometimes with paramotor both free and paramotor mostly with paramotor sometimes free exclusively paramotor but appreciate better economy easier launch and nicer handling than in standard paramotor wing like Synthesis2 Universal is a great free flying recreational paraglider including cross country Beginner XC pilots will surely appreciate exceptional comfort in uneasy thermals resulting from considerable amount of reflex traits present in the design On activating the trimmers and setting up the ALC steering Universal becomes a full reflex paramotor wing good for both leisure and cruise flying thermalling last but not least for initial paramotor training No matter what kind of flying you choose the Universal has a perfect launch rigid canopy
49. ving it In this case the safest way to deal with this question is to close the throttle and release the brakes Especially less experienced pilots tend to overreact This is called a pilot induced oscillation and proven solution is to leave the brakes alone 3 3 2 LEVEL FLIGHT Once you have gained safe height after take off and wish to go for a route you can turn onto the right direction fully open the trimmers and let off the brakes If the conditions are turbulent it can look foolhardy but this is the essential feature of the reflex profile the faster you fly the the safer your wing is That s why it s truly possible to release the brakes and enjoy your flight CAUTION Some pilots with previous free flying experience may have a well grounded habit of keeping the brakes slightly applied at all times Such a technique while quite reasonable on a free flying wings as it allows for quick pilot reactions and decreases sink is not advisable on reflex profile paragliders When you pull the brakes the Universal profile loses its reflex characteristics see next page If you have a variometer or altimeter aboard watch it In level flight it is very easy to start climbing unintentionally The instruments will help you optimise speed and fuel economy Of course each flight will depend on current configuration of your gear but due to its ability to fly safe without constant piloting the Universal will let you adjust everything to th
50. y brake operation or steering inputs in general should be smooth and gentle m Do not try to take off until you have your wing overhead Hitting power before that can cause dangerous oscillations m Do not sit in the harness until you are sure you are flying m The faster the trim setting is the more brake input is required to take off m The lower the hangpoints of your power unit are the easier is the launch Reverse launch in strong wind Reverse launch can be executed holding in one hand both A risers and one brake with throttle and the second brake in the other hand With a decent e Universal wind it is by far the best way In weaker wind it is better to prepare a classic launch as running backwards with an engine on your back is not an easy thing to do It is reasonable not to pull the wing up until you are really determined to launch especially when it is clipped in Lay down the rolled paraglider with its trailing edge against the wind Unfold the wing enough to find the risers and check that no lines are looped over the leading edge Stretch the risers against the wind separating the right and left one We suggest that you lay the risers in the same way as you will be turning during reverse launch and place one riser over the other with rear risers upmost It should be done this way because once you clip in the cage of your power unit will make turning on your own practically impossible Now run the pre launch c
Download Pdf Manuals
Related Search