Universal bracket manual
Contents
1. cation tool and drill Use 9 mm drill Use spirit level in steps 2 and 3 to ensure that the installation is level A level installation is required in order for the product to work without problems gt gt a5 Use a spacer that SS compensates for the mat s thickness Mark where the hole will be drilled into the L pro Spacers between 5 45 mm height are available file bracket forall lees to buy as options Contact Autoadapt Support for further help Installation 6 Turny Evo Getting seated 3 Install the L profile brackets to the mounting legs Options or 2 applies to all types of bent and twisted legs Option 3 only applies to flat legs Option 2 Fit the screws from the outside and in Important that the washer is placed with the screw Fit the screws from the inside and out Important that the washer is placed with the screw N Option 3 Use the screws and the three hole nut which is intended for installing Turny Evo s base plate on the L profile bracket Apply thread locking on all screw connections at the final installation Getting seated Turny Evo 7 Adapt bracket for the car s middle section Box content Under no circumstances is it allowed to weld in the construction The bracket is only crash tested and approved based on the installation procedure which are described in this manual Installation x28 Screw M8x20 lt x24 Washer 82. info autoadapt com Worldwide Safe Mobility Solutions Included in our corporate group are Autoadapt BraunAbility Bruno Independent Living Aids and Unwin Safety Systems 422988 1 2015 05 EN
3. 4x16x1 6 amp x8 Hex lock nut M8 un x 4 Two hole nut x4 Three hole nut x4 Mid bracket x2 L profile bracket x2 Cross beam 8 Turny Evo Getting seated Install the L profile brackets of the application tool All instructions in this chapter show an installation of a right turning Turny Evo The approach for a left swivelling unit is the same Begin by installing the L profile brack ets to the application tool Secure the screws loosely in order to be able to adjust the L profile brackets position in place in the car Under no circumstances is it permitted to weld in the construction The bracket is only crash tested and approved based on the installation proce dure which are described in this manual Getting seated Turny Evo 9 Install the cross beams and adapt the construction Place the cross beams above OEM seat attachment so that Turny Evo can be installed at the desired distance from the door Use the application tool with the fixed L profile brackets to find out which option below is relevant Installation Option A OEM seat attachment ends up outside the attachment of Turny Evo The L profile bracket towards the door must Turny Evo be adapted for the cross beams Towards the door L profile bracket towards door Option B 2 OEM seat attachment ends up inside the attachment of Turny Evo The cross beams can be shortened so that the L profile bracket covers t
4. because it will then end up within Turny Evo s crash segment Strive to place the L profile brackets as parallel with each other as possible This may mean that OEM seat attachment ends up on both sides of the L profile bracket which is a correct alternative solution This part of the application tool lie against the B pillar to ensure that Turny Evo has the best possible swivelling space The L profile bracket closest to the door be laterally inverse when required as the illustration to the right shows The specified distance measurements apply to all seat attachments no matter how the side of the L profile bracket is placed Getting seated Turny Evo 3 Adapt the L profile brackets The L profile brackets must be cut to the correct installation height and adapted so it does not lean If the right and left sides differ the L profile brackets must be adapted separately Also decide in this step how the leg will be adapted see next page Start the adaptation of the L profile brackets by taking out the following measurements Installation A Measurement for adapting the height do not use a spirit level Measure the distance between the application tool and the threshold of the car B Measurement to correct any inclination place a spirit level at the highest point of the L profile bracket and lift up the other end until it is horizontal Measure the distance between the spirit level and the applic
5. Oe 8 Turny Evo Getting seated Left model 1 1 Place the frame with the E threaded holes on the bottom f J Getting seated Turny Evo 9 NURWN The grey marked part of the application tool corresponds to the base plate of Turny Evo and the cross frame corresponds to the unit s crash segment The cross frame must not rest on the L profile bracket but must be placed at the side in order that the installation will be level and stable Holes which are prepared for Turny Low Vehicle Not used for this installation Holes for cables that run out from Turny Evo Three attachment points in each corner for installing of Turny Evo on L profile bracket Should be flush with B pillar and threshold when fitting the L profile bracket Shows Turny Evo s position to the B pillar The bigger the distance to the B pillar the earlier Turny Evo can be programmed to turn out Shows how much space is needed to run Turny Evo backwards in order to access the attachment points forward when installing on the L profile bracket Note that Turny Evo can run a further 10 cm backwards Shows Turny Evo s position to the transmission tunnel Shows Turny Evo s main programmable end position n A Threshold Transmission tunnel Installation 0 Turny Evo Getting seated Adapt bracket for the car s front section Box content Under no circumstances is
6. ation tool Also note measurement to cut out for any beams or unevenness in the floor Threshold B pillar Loosen the L profile brackets from the application tool mark out the measurement of the L profile brackets and cut Below is an example which shows how the mat should be marked out A 4 5 cm B 3 cm add a further 0 5 cm to provide room divide the measurement into two and subtract from or add for the L profile bracket leg or mat to the A measurement to achieve the correct inclination A 1 5 6 5 cm A 1 5 7 3 5 cm 4 Turny Evo Getting seated Adapt the mounting legs Bend turn and place the mounting leg based on the conditions that prevail in the car The short part of the leg must however always be installed on the inside and outside of the L profile bracket Allow the conditions in the car combined with the aesthetics determine what is best The design is very forgiving which simplifies the adaptation since there is some adjustment range in the installing itself To achieve a stable construction the mounting legs are placed as far from each other as possible out towards the short sides of the L profile bracket Begin by deciding the leg s placement and then do the bending or twisting towards the seat adjustment Keep in mind that the measurement between the L profile bracket and centre of OEM seat attachment must be between 15 45 mm Example of an adapted mounting leg A The twisted leg that r
7. eaches out to an attach ment that is slightly to one side B The bent leg which is placed on the inside of the L profile bracket so that it is not visible C The bent leg which is used to regulate the height of the rear edge of the L profile bracket D The bent leg which is used as a spacer be tween the mat and L profile bracket E The bent leg which is placed on the outside of the L profile bracket F The flat leg which is placed under the L pro file bracket to bring it down to the height of the installation in the front edge F Drill holes in the dimensions which Drill holes for phasing in the L profile If option F is practised above use the are adapted for OEM seat attach bracket Use the two hole nut asa tem three hole nut as a template to mark out ment Centre the hole for the best plate to mark out the hole s position the hole s position strength Adapted 9mm 9 mm Do not drill Do not drill through the nut through the nut Sc IN Getting seated Turny Evo 15 Install the bracket in the car Install all mounting legs in OEM seat attachment in the floor Use a spacer that compensates for the mat s thickness 2 Attach the Lprofile brackets to the application tool again and put it back into the intended position in the car Mark where the hole for each mounting leg will be drilled into the L profile bracket Then loosen the L profile brackets from the appli
8. for your independence PaAutoadapt Turny Evo Autoadapt Application tool and universal bracket Front section Middle section EN Installation manual Getting seated Turny Evo 5 Thank you for choosing a Application tool and universal bracket from Autoadapt The manual that follows is an integral important part of the product providing you with information on how to perform accurate and safe installation of the product Please read through the manual carefully before starting your work If you have any questions about your customer s adaptation please feel free to contact Autoadapt Your feedback is important to us It helps us in our work of continuously improving our product and its installation You can find more information about us and our range of car adaptation solutions by visiting www autoadapt com u Ta e z N ha Once again thank you for placing your confidence in our products es ES Autoadapt Safe vehicle adaptation solutions For your safety Autoadapt products are designed and tested according to current directives and standards Assemble the application tool 6 Right model 8 Left model Adapt bracket for the car s front section 10 Box content II Position the application tool in the car I3 Adapt the L profile brackets 14 Adapt the mounting legs I5 Install the bracket in the car Adapt bracket for the car s middle section 17 Box content 18 Install the L p
9. he whole side Turny Evo E Towards the door L profile bracket towards door 20 Turny Evo Getting seated 2 Install the cross beams according to the instructions that are relevant below Then adapt the L profile bracket or cross beams based on the option which is relevant on the previous page Loosen the L profile bracket from the application tool if it is to be adapted VA Adapted Be Drill holes into the cross beam in the dimen sions which are adapted for OEM seat attach a ment Use OEM screw l l OEM quick attachment OEM floor attachment Drill holes into the cross beam in the dimensions which are adapted for the wire lock The wire lock must in turn be adapted for OEM seat attachment ia WW Adapted Wire lock with MI2 and MIO thread is available to buy as an option Contact Autoadapt Support for further help _ _ OEM rail Make a washer that can be slid into the relevant rail The washer must be 8 mm thick and have threaded holes Use washer for the screw Option Option II mm Option 2 9 mm y An Option 2 Getting seated Turny Evo 2 Install the bracket in the car Remount the L profile bracket onto the application tool if it has been adapted Place the application tool on top of the cross beams and by using the tool ensure that there is suf ficient space for Turny Evo paths Adjust the L profile brackets laterally where
10. it permitted to weld in the construction The brack et is only crash tested and approved based on the installation procedure which are described in this manual J x20 Screw M8x20 x 8 Washer 8 4x16x1 6 Can x 4 Two hole nut x4 Three hole nut x4 Mounting leg x2 L profile bracket Getting seated Turny Evo Position the application tool in the car All instructions in this chapter show an installation of a right turning Turny Evo The approach for a left swivelling unit is the same Begin by installing the L profile brack et to the application tool Secure the screws loosely in order to be able to adjust the L profile brackets position in place in the car Installation 2 Turny Evo Getting seated 2 Place the application tool in the car and centre it above OEM seat attachment in the floor Then adjust the L profile brackets laterally The distance between L profile bracket and cen tre of OEM seat attachment must be between 15 45 mm in order that the installation will be stable A distance of at least 15 mm at the same time ensures that the head of the screw will not take in the rounding of the bent leg when installing By using the application tool ensure that there is sufficient space for Turny Evo movement paths When required the L profile bracket closest to the door can be laterally inverse to achieve an optimal position The L profile bracket closest to the transmission tunnel may not be turned round
11. required Mark each hole for each mounting leg to be drilled in the L profile brackets and beams Then loosen the L profile brackets from the application tool and drill Use spirit level in steps 2 and 3 to ensure that the installation is level A level installation is required in order for the product to work without problems Spirit level 2 Drill two holes into the side of the L profile bracket and two holes in the cross beam for each mounting leg 9mm Installation Mark where the hole will be drilled into the L pro file bracket and the cross beam for all legs 22 Turny Evo Getting seated 3 Install the L profile brackets to the cross beams Fit the screws from the outside and in Important that the washer is inserted with the screw Apply thread locking on all screw connections at the final installation NEDA TERTE ead ag A o eS 2 AmA Pe rer Uy 1976 Se ISO IEC 17025 O 90012 Accredited by SWEDAC as testing laboratory in accordance with ISO IEC 17025 2005 Quality system certified in accordance with ISO 9001 2008 Illustrations descriptions and specifications in the user manual are based on current product information Autoadapt reserves the right to make alterations without previous notice O 2015 Autoadapt AB CE www autoadapt com facebook com autoadapt twitter com autoadapt AUTOADAPT AB Akerivagen 7 S 443 61 Stenkullen Sweden Phone 46 302 254 00 E mail
12. rofile brackets of the application tool 19 Install the cross beams and adapt the construction 21 Install the bracket in the car Index 6 Turny Evo Getting seated Assemble the application tool Right model I I i Place the frame with the threaded holes on the bottom Getting seated Turny Evo 7 NURWwN The grey marked part of the application tool corresponds to the base plate of Turny Evo and the cross frame corresponds to the unit s crash segment The cross frame must not rest on the L profile bracket but must be placed at the side in order that the installation will be level and stable Holes which are prepared for Turny Low Vehicle Not used for this installation Holes for cables that run out from Turny Evo Three attachment points in each corner for installing of Turny Evo on L profile bracket Should be flush with B pillar and threshold when fitting the L profile bracket Shows Turny Evo s position to the B pillar The bigger the distance to the B pillar the earlier Turny Evo can be programmed to turn out Shows how much space is needed to run Turny Evo backwards in order to access the attachment points forward when installing on the L profile bracket Note that Turny Evo can run a further 10 cm backwards Shows Turny Evo s position to the transmission tunnel Shows Turny Evo s main programmable end position Transmission tunnel Installation I un E a
Download Pdf Manuals
Related Search