HU-Aurora Status Display User Manual v01
Contents
1. A on matrix 1 level m is routed to destination D on matrix 2 level n using the tie line Source A is the upstream source Destination B is a tie line destination and is at the upstream end of the tie line Source C is a tie line source and is at the downstream end of the tie line The tie line is busy if source C is routed to one or more destinations Issue 1 Dec 002. Display User Manual The layout of a multi level Destination Orientated Status page is shown below pro bel DESTINATION ORIENTATED STATUS MATRIX mmmmmmmmmmmmmmmm LEVELS 11111111 11111111 11111111 11111111 11111111 11111111 ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S sss
3. according to device position set up in section 4 2 Issue 1 Dec 00 31 32 pro bel Aurora Status Display User Manual Links PL25 to PL30 on the 2411 define the multi drop address of the status display unit Set up the multi drop address of the 2411 using the following table as a guide MULTI Batic LINK POSITION ADDRESS PL30 PL29 PL28 PL27 PL26 PL25 01 down down down down down up 02 down down down down up down 03 down down down down up up 04 down down down up down down 05 down down down up down up 06 down down down up up down 07 down down down up up up 08 down down up down down down 09 down down up down down up 10 down down up down up down 11 down down up down up up 12 down down up up down down 13 down down up up down up 14 down down up up up down 15 down down up up up up 16 down up down down down down All other settings of links PL25 PL30 are invalid and will not be recongnised by the Aurora controller e Connect the 6170 at the panel port and position defined in the editor Issue 1 Dec 00 Aurora Status Display User Manual pro bel The status display unit will need a pin swapped RS485 cable to connect to the Aurora controller The pinout is given below AURORA FUNCTION 6170 2411 CONTROLLER STATUS DISPLAY UNIT 1 Chassis 1 2 Rx 3 TX 7 4 OV 4 5 N C 5 6 OV 6 7 Rx 3 8 Tx 2 9 Chassis
4. dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd MORE Issue 1 Dec 00 25 Aurora Status Display User Manual pro bel KEY Update indicates whether the page needs updating or not the page is up to date UPDATE the page needs to be updated mmmmmmmmmmmmmmmm name of the currently selected matrix tttttttttttttttt name of the currently selected tie line name dddddddd the name of a destination association which is using the tie line more indicates whether there are more destinations than can be displayed or not all destinations are on display MORE there are more destinations than can be displayed on this page 3 8 2 Page Operation This page allows the User to examine a snapshot of the usage of a single tie line coming in to a matrix This page can only be selected when the Tie Line Summary page is active To select the Tie Line details page press the lt Tie Line gt key The tie line is selected from the Tie Line Summary Page There may be up to 8 columns of 8 destinations displayed on this page If there are more destinations than can be displayed on a single page then M
5. lt SOURCE ORIENT gt key to select the Source Orientated Status page The lt SOURCE ORIENT gt key LED will be lit This page allows the User to list the destinations that a source is routed to This page is a snapshot display and is only updated when the User requests it This page has 3 modes of operation selecting a matrix dialling up a source preselect and selecting a level The cursor keys are used to switch between the different modes The field being edited is highlighted in inverse video An LED in the numeric keypad may be lit indicating the currently selected matrix or level depending on which field is active 3 6 2 1 Selecting a Matrix To select a matrix first use the cursor keys to highlight the MATRIX field The LED in the numeric keypad associated with the currently selected matrix will light Press the numeric key corresponding to the desired matrix to select the matrix This will clear any transferred sources The LED in the numeric keypad associated with the newly selected matrix will be lit 3 6 2 2 Dialling up a source Preselect To dial up a source preselect first use the cursor keys to highlight the PRESELECT field In this mode the combined source numeric keypad is a source keypad This allows a source association to be dialled up in exactly the same way as using a panel Issue 1 Dec 00 21 22 Aurora Status Display User Manual pro bel Providing a dial up keypad has been configured and assigned
6. to the panel within the editors Press the lt CLEAR gt key to clear the PRESELECT field and then enter the required source 3 6 2 3 Selecting a level To select a level first use the cursor keys to highlight the LEVEL and SOURCE fields The LED in the numeric keypad associated with the currently selected level will light Press the numeric key corresponding to the desired level and source to select that level and source The LED in the numeric keypad associated with the newly selected level will light Press the lt CLEAR gt key to clear the LEVEL and SOURCE fields 3 6 2 4 Taking a Snapshot If a valid source has been selected then pressing the lt UPDATE gt key takes a snapshot of the current state of the system and updates the page If UPDATE appears in the top left hand corner of the page the LED in the lt UPDATE gt key will also be lit then it means that the snapshot information may be out of date Press the lt UPDATE gt key to refresh the page The update required indication will be turned off Issue 1 Dec 00 3 7 Aurora Status Display User Manual Tie Line Summary page 3 7 1 Description The layout of a Tie Line Summary page is shown below pro bel pro bel Update TIE LINE SUMMARY MATRIX mmmmmmmmmmmmmmmm TIE LINE NAME TYPE GRP UPSTREAM SOURCE TIE LINE USE tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSS
7. 111 prt cd id tttt 1111111l prt cd id tttt 11111111 prt cd id tttt I1111111 prt cd id tttt 1111111l prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt Ill11111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt Ill11111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt Ill1l1111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt 11111111 prt cd id tttt 1111111 prt cd id tttt Ill1l1111 prt cd id tttt 11111111 prt cd id MORE KEY mmmmmmmmmmmmmmmm name of the currently selected matrix tttt The type of diagnostic either PORT or CARD 11111111 The name of the level from which the diagnostic Issue 1 Dec 00 27 Aurora Status Display User Manual pro bel was reported prt The matrix port number cd Module number or card number for CARD diagnostics only id Card id for CARD diagnostics only 01 99 card or module number iy input card Cc crosspoint card g output card more Indicates whether there are
8. 9 e Connect the monitor to the monochrome output on the back of the Status Display Unit 4 4 Internal Status display Connect the monitor to the monochrome output on the back of the Aurora controller The output is presented on a 9 way D type socket with the following pin out 9 WAY FUNCTION 1 RED N C BLUE N C N C GREEN MONO N C Sync oo 9 Io oF A Ww N Chassis Issue 1 Dec 00 33 Aurora Status Display User Manual pro bel 4 5 Status Display Control Panel 6708 e Set up Panel Mode switch on the rear of the 6708 Control Panel as follows SWITCH SETTING 1 1 2 0 3 0 4 0 5 1 6 1 7 1 8 1 e Set up the multi drop address of the panel using the Address Switch on the back of the panel according to multidrop address set by the editor e Connect the Control panel at the panel port and position defined above A 9W pin to pin cable will be required to connect the control panel to the Aurora controller 4 6 Troubleshooting e Check that the multi drop address set up on the Control panel is correct e Check that the multi drop address set up on the Status Display Unit is correct for external displays e Check that the Control panel is connected to one of the Aurora controller s panel ports and not to the back of a Status Display Unit for external displays e Check that the database has been co
9. Aurora Status Display User Manual pro bel Contents 1 Introduction 4 2 Overview 5 2 1 Introduction 5 2 2 Destination orientated Status information 7 2 3 Source orientated Status information 7 2 4 Tie line status information 7 2 5 Matrix Diagnostic information 7 2 6 Panel Diagnostic information 8 2 7 Configuration Options 8 2 7 1 Status Display Unit 8 2 7 2 Status Display Control Panel 8 3 Operation 10 3 1 Introduction 10 3 2 Status Display Control Panel 11 3 3 Select Matrix Page 12 3 3 1 Description 12 3 3 2 Page Operation 12 3 4 Destination Orientated Status Pages 13 3 4 1 Description 13 3 4 2 Basic Page Operation 15 3 4 3 Extended Page Operation 16 Issue 1 Dec 00 3 5 Destination Orientated Status Setup Page 3 5 1 Description 3 5 2 Page Operation 3 6 Source orientated Status Page 3 6 1 Description 3 6 2 Page Operation 3 7 Tie Line Summary Page 3 7 1 Description 3 7 2 Page Operation 3 8 Tie Line Details Page 3 8 1 Description 3 8 2 Page Description 3 9 Matrix Diagnostics Page 3 9 1 Description 3 9 2 Page Operation 3 10 Panel Diagnostics 3 10 1 Description 3 10 2 Page Operation 4 Installation and Troubleshooting 4 1 Introduction 4 2 Aurora Editor 4 3 Status Display Unit 6170 4 4 Internal status Display 4 5 Status Display Control Panel 6708 Aurora Status Display User Manual 17 17 18 20 20 21 23 23 24 25 25 26 27 27 28 29 29 30 31 31 31 31 33 34 Issue 1 Dec 00 Aurora Status Display
10. Examining the Use of a Tie Line To see the next destination in the list of destinations which are using the tie line press the lt TIE LINE STATUS gt key To view all of the destinations which are using the currently selected tie line press the lt TIE LINE gt key to switch to the Tie Line Details page 3 7 2 4 Updating the Page If UPDATE appears in the top left hand corner of the page as well as the lt UPDATE gt key LED being on then it means that the snapshot information may be out of date Press the lt UPDATE gt key to refresh the page The update required indications will then clear 3 7 2 5 Clearing a Single Destination Press the lt CLEAR gt key to route the safe source on the appropriate matrix and level to the displayed destination for the currently selected tie line If the Tie Line Clear function has not been enabled on the control panel or if the safe source has not been set up using the Aurora Editors then the keypress is ignored and no action is taken 3 8 Tie Line Details Page 3 8 1 Description The layout of the Tie Line Details page is shown below Update TIE LINE DETAILS pro bel CHYRON MATRIX mmmmmmmmmmmmmmmm TIE LINE tttttttttttttttt dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd dddddddd
11. O and ANALOGUE TO AES AUDIO tie lines no group 01 99 Group 01 to 99 SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS The names of the matrix level and upstream source feeding the tie line nnnn 0000 to 9999 the number of destinations using the tie line dddddddd The name of a destination association which is using the tie line PG UP PG DN Use the lt PAGE UP gt key to access the Page s before this one or the lt PAGE DOWN gt key to access the page s after this one 3 7 2 Page Operation Press the lt TIE LINE gt key to select the first Tie Line Summary page The lt TIE LINE gt key LED will light as well as the numeric key LED associated with the currently selected matrix This page allows the User to examine a snapshot of the usage of the tie lines coming into a matrix A snapshot is taken when the page is displayed and when the lt UPDATE gt key is pressed see Updating the Page below 3 7 2 1 Selecting a Matrix To display the first Tie Line Summary page for a particular matrix press the numeric key corresponding to the desired matrix The LED on the numeric keypad associated with the newly selected matrix will light 3 7 2 2 Selecting a Tie Line The name of one of the tie lines on this page is highlighted in inverse video This is the currently selected tie line The cursor keys can be used to select any tie line in the list Issue 1 Dec 00 Aurora Status Display User Manual pro bel 3 7 2 3
12. ORE is displayed in the bottom right hand corner of the page 3 8 2 1 Updating the Page If UPDATE appears in the top left hand corner of the page as well as the lt UPDATE gt key LED being lit then it means that the snapshot information may be out of date Press the lt UPDATE gt key to refresh the page The update required indications will then clear 3 8 2 2 Clearing all Destinations Press the lt CLEAR gt key to route the safe source on the appropriate matrix and level to all of the displayed destinations for the currently selected tie line Issue 1 Dec 00 Aurora Status Display User Manual pro bel If the Tie Line Clear function has not been enabled on the control panel or the safe source had not been set up using the Aurora editors then the keypress is ignored and no action is taken 3 8 2 3 Switching back to the Tie Line Summary Page Press the lt TIE LINE gt key to switch back to the Tie Line Summary page for the currently selected matrix 3 9 Matrix Diagnostics Page 3 9 1 Description The layout of the Matrix Diagnostics page is shown below pro bel MATRIX DIAGNOSTICS MATRIX mmmmmmmmmmmmmmmm TYPE LEVEL PRT CARD TYPE LEVEL PRT CARD TYPE LEVEL PRT CARD tttt 11111111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt LIJ11111 prt cd id tttt 1111111 prt cd id tttt 11111111 prt cd id tttt I1111111 prt cd id tttt 1111111l prt cd id tttt 11111111 prt cd id tttt 11111
13. SSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd tttttttttttttttt iiii gg SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS nnnn dddddddd PG UP PG DN KEY Update Indicates the page needs to be updated mmmmmmmmmmmmmmmm tttttttttttttttt iiii Issue 1 Dec 00 the page is up to date UPDATE the page needs to be updated tie line name tie line type AUTO MAN manual tie line name of the currently selected matrix automatic tie line Aurora Status Display User Manual pro bel gg GROUP NO used with AES to ANALOGUE AUDI
14. User Manual pro bel 4 6 Troubleshooting 34 5 Led Diagnostics 35 5 1 Remote Status Display 2411 35 5 2 Status Display Control Panel 35 6 Tie Lines 36 6 1 Tie Line Terminology 36 Issue 1 Dec 00 Aurora Status Display User Manual pro bel 1 Introduction This document provides details on how to use and install the status display s provided with the Pro Bel Aurora control system Section 2 gives an overview of the status display Section 3 describes the operation of the status display and the status pages provided Appendix A is an installation guide Appendix B provides information on any LED diagnostics provided Appendix C provides an introduction to tie lines and some of the terminology 4 Issue 1 Dec 00 Aurora Status Display User Manual pro bel 2 Overview 2 1 Introduction The Aurora status displays are configured to provide an 80 columns wide black and white video output in either 525 or 625 lines format There are two possible status display configurations either local from the 2633 main control card located in the Aurora frame or remote using 6170 remote Status and Diagnostic Units RSDU The RSDU is housed inside a 6170 1U 19 rack frame Each status display device has an associated 1U control panel which is used to select the various status pages Aurora provides a monochrome video output from the main 2633 control card The video output is presented at the rear of the controller The associated c
15. ated Status page If there are no valid source routeds on any levels of the selected destination association then no sources are transferred 3 4 2 3 Displaying Protect Information Press the lt PROTECT STATUS gt key to display protect information The LED in the lt PROTECT STATUS gt key will light to indicate that protect status is being displayed If any displayed level of a destination association is protected then the source routed name for that level is overwritten with the name of the panel which is protecting that level To return to the normal source routed display press the lt PROTECT STATUS gt key again 3 4 2 4 Displaying Tie Line Information Press the lt TIE LINE STATUS gt key to display tie line information The LED in the lt TIE LINE STATUS gt key will light to indicate that tie line status information is being displayed If the destination for a displayed level of a destination association is an upstream tie line destination then the source routed name for that level is overwritten with the name of the tie line which the destination is part of Because tie line names are 16 characters long the display alternates between displaying the first and second set of 8 characters To return to the normal source routed display press the lt TIE LINE STATUS gt key again 3 5 Destination Orientated Status setup page 3 5 1 Description The Destination Orientated Status Setup page allows the user to configure the l
16. d Press the lt CLEAR gt key to clear the level There must always be at least one level selected If there is only one level selected then the lt CLEAR gt key is disabled All LEDS on the numeric keypad will be turned off 3 5 2 4 Changing a Level Select the level field that needs to be changed Select the required level by pressing the appropriate numeric key on keypad 1 corresponding to the level The LED in the associated numeric key for the selected level will also light 3 5 2 5 Return to Destination orientated Status page Press the lt DEST ORIENT gt key to return to the destination orientated status page The lt SETUP gt key LED will be turned off Issue 1 Dec 00 19 3 6 20 pro bel Aurora Status Display User Manual Source Orientated Status page 3 6 1 Description The layout of the Source Orientated Status page is shown below Update pro bel CHYRON DESTINATION ORIENTATED STATUS MATRIX mmmmmmmmmmmmmmmm PRESELECT pppppppp SOURCES Ol ssssssssR 02 ssssssssR 03 ssssssssR 04 ssssssssR 05 ssssssssR 06 ssssssssR 07 ssssssssR 08 ssssssssR 09 ssssssssR 10 ssssssssR 11 ssssssssR 14 ssssssssR 13 ssssssssR 14 ssssssssR 15 ssssssssR 16 ssssssssR LEVEL 11111111 SOURCE ssssssss SNAPSHOT OF DESTINATIONS LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLE LLLLLLLLLLLLLLLLLLLLLLLLLLLLLELLLLLE LLLLLLLLLLLLLLLLLLLLLLLLLLLLLELLLLLE eeeeeeeeeeceeeeeceeceeeeeeeeeeeeececece eeeeeeeeeeceeceececeecee
17. de the following e Source routed information on all matrices in the system e Up to 6 levels can be viewed at the same time The selection of levels and the order in which they are displayed is user configurable e PROTECT and TIE LINE status information Whilst destination orientated status information pages are active the following functions are also provided e The ability to protect unprotect a selected destination e The ability to protect a source routed and transfer them to the Source Orientated Status page to find out the usage of that source 2 3 Source Orientated Status Information The source orientated status information pages are used to find out which destinations are using a source The source may either be one of a group of sources transferred from one of the Destination Orientated Status information pages or part of a source association dialled up using the source keypad on the 6708 control panel 2 4 Tie Line Status Information The tie line status information pages provide the following e The use of tie lines going into any matrix in the system e The ability to clear either single or all destinations which are using a selected tie line by routing a safe source to them 2 5 Matrix Diagnostic Information The matrix diagnostic information page provides port and module fault indications Issue 1 Dec 00 2 6 2 7 Aurora Status Display User Manual pro bel Panel Diagnostic Information The panel
18. diagnostic information page provides information about the system indicating expected devices that are not detected and unexpected devices that are detected Configuration Options This section describes the configuration options available from the Aurora editors for a status display unit and associated control panel 2 7 1 Status Display Unit The following configuration options are available from the Aurora configuration editors e Show 4 or 8 character names e Internal or External device e Use 525 or 625 lines The default for these options is 625 lines format and 8 character names Configuration of these buttons is via radio buttons presented on the edit form for each status display 2 7 2 Status Display Control Panel The following configuration options are available from the advanced tab of the status display control panel form e Enable Disable Protect Key e Enable Disable Tie Line clear e Master Normal Panel Mode The default for these options is Tie line clear and Protect Key Disabled and Normal Panel Mode If the Enable Disable Protect Key check box is ticked then the protect key is enabled on the panel Issue 1 Dec 00 Aurora Status Display User Manual pro bel If the Enable Disable Tie Line Clear check box is ticked then the ability to clear down tie lines is enabled If the Master Normal Panel Mode check box is ticked then the panel is set in master panel mode thus enabling the status
19. display panel to cancel a protect ona destination made by another panel 3 3 1 10 Aurora Status Display User Manual pro bel Operation The following sections describe the operation and fuctions of the various pages ofa status display Introduction Each status display has a matrix number associated with it This may be changed either by accessing the Select Matrix page refer to section 3 3 or by using the numeric keys see section 3 2 in various sub modes of the other pages When a Status display is powered up for the first time the Select Matrix page refer to section 3 3 is displayed with the first matrix in the system selected otherwise the system attempts to return to the page where a matrix selection was active prior to the power down or reset A status display provides 6 basic status page information types e Select Matrix Page This is used to select the matrix for which status information is to be obtained e Destination Orientated Status Pages These pages provide status information i e Source routed protect and tie line status in a destination orientated fashion When this type of page is active protects can be set or cleared and tie lines may be cleared down e Source Orientated Status Page This page allows source use to be investigated e Tie Line Summary Status Pages These pages provide a basic summary of tie line information for a matrix e Matrix Diagnostics Page This page provides a lis
20. eeeeceeceeeeeceecee eeeeeeeeeeceeceeeeceeceeeececeeceeeeeeceecee eeeeeeeeeceeceeceeceeceeeeeeeeceeeeeeceecee eeeeeeeececeecececeeceeeeeeeeeeeeeeceecee eeeeeeeeeeeeceeceeeeeceeceeceeeeeeceeceecee eeeeeeeeeeececeeceeceeceeceeeeeeeeceeceece eeeeeeeceeeeeeeeeceececeeceeceeeeeeeeceecee eeeeeeeeeeeceeeeeececeeceeeeeceeceeceeceece eeeeeeeeeeeceeceeeeceeceeeeeeeceeceeceeceece eeeeeeeeeeeceeceecececeeceeeeeceececeeceece eeeeeeeeeeeceeeeeeceeceeceeeececeeceeceecece eeeeeeeceeceeececeececeeceeceeceeceececeeceece PG UP PG DN KEY Update UPDATE mmmmmmmmmmmmmmmm PPPPPPPP Indicates whether the page needs updating or not the page is up to date the page needs to be updated name of the currently selected matrix If sources have been dialled up then the source preselect characters are shown otherwise if the sources have been Transferred from a Destination Orientated Status page TRANSFER 11111111 name of selected level Issue 1 Dec 00 Aurora Status Display User Manual pro bel SSSSSSSSSS name of source on the selected level eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee name of a matrix level and destination association that the selected source is routed to R local remote source diagnostic local source R remote source PG UP use the lt PAGE UP gt key to access the page s before this one PG DN use the lt PAGE DOWN gt key to access the page s after this one 3 6 2 Page Operation Press the
21. evels setup for each matrix in the system The levels setup determines the format of the Destination Orientated Status pages Issue 1 Dec 00 17 18 Aurora Status Display User Manual pro bel The layout of the Destination Orientated Setup Setup page is shown below pro bel DESTINATION ORIENTATED STATUS MATRIX mmmmmmmmmmmmmmmm LEVELS AVAILABLE 11111111 1111111 11111111 11111111 11111117 11111111 1111111 11111111 11111111 1111111 111171111 11111111 17111111 11111111 1111111 11111111 LEVELS SELECTED 111111171 1111111 11111111 11111111 11111111 11111111 KEY mmmmmmmmmmmmmmmm name of the currently selected matrix 11111111 the name of a level on the currently selected matrix 3 5 2 Page Operation This page allows the User to select up to 6 levels which will be displayed on the Destination Orientated Status pages The levels setup is stored for each matrix The default levels setup is levels 1 to 6 selected The levels setup is stored in battery backed RAM so that the system remembers any changes that are made to the levels setup The order in which the levels are selected determines the order in which they are displayed on the Destination Orientated Status pages The number of levels selected determines the format of the Destination Orientated Status pages If one level is selected then single level Destination Orientated Status pages are used If two or more levels are selected then multi level Destinati
22. fter this one 3 4 1 2 Basic Page Operation Press the lt DEST ORIENT gt key to select the first Destination Orientated Status page for the selected matrix The LED in the lt DEST ORIENT gt key will light to indicate that a destination orientated status page is active as well as the LED in the numeric keypad corresponding to the selected matrix The primary function of these pages is to allow the user to examine the source routed on up to 6 levels of a matrix Each matrix in the system has its own specific levels setup which is configured from the Destination Orientated Setup page The format of the Destination Orientated Status page is determined by this levels setup If the selected matrix only has one level then single level Destination Orientated Status pages are used If the selected matrix has two or more levels then multi level Destination Orientated Status pages can be used Issue 1 Dec 00 15 16 Aurora Status Display User Manual pro bel 3 4 1 3 Selecting a Matrix To display the source routed information on a matrix press the numeric key corresponding to that matrix Pressing a numeric key selects the matrix corresponding to the key and displays the first Destination Orientated Status page for that matrix The LED in the numeric key will illuminate to indicate the selected matrix 3 4 1 4 Selecting a Destination Association The name of the selected destination association is highlighted in inverse video The c
23. le level Destination Orientated Status page is shown below DESTINATION ORIENTATED STATUS pro bel CHYRON MATRIX mmmmmmmmmmmmmmmm LEVEL 11111111 ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S ddddddd DM ssssssss S PG UP PG DN Issue 1 Dec 00 13 pro bel Aurora Status
24. mmmm 11 mmmmmmmmmmmmmmmm 02 mmmmmmmmmmmmmmmm 12 mmmmmmmmmmmmmmmm 03 mmmmmmmmmmmmmmmm 13 mmmmmmmmmmmmmmmm 04 mmmmmmmmmmmmmmmm 14 mmmmmmmmmmmmmmmm 05 mmmmmmmmmmmmmmmm 15 mmmmmmmmmmmmmmmm 06 mmmmmmmmmmmmmmmm 16 mmmmmmmmmmmmmmmm 07 mmmmmmmmmmmmmmmm 17 mmmmmmmmmmmmmmmm 08 mmmmmmmmmmmmmmmm 18 mmmmmmmmmmmmmmmm 09 mmmmmmmmmmmmmmmm 19 mmmmmmmmmmmmmmmm 10 mmmmmmmmmmmmmmmm 20 mmmmmmmmmmmmmmmm KEY mmmmmmmmmmmmmmmm MATRIX NAME This page will only show the matrices defined within the system database 3 3 2 Page Operation This page allows the user to view the names of all of the matrices in the system and to select one using the numeric keypad and or cursor keys All of the status display pages except for the panel Diagnostics page show information relating to the selected matrix Therefore changing the selected matrix using this page changes the information that is displayed on the other status pages Press the lt MATRIX gt key to select the SELECT MATRIX page The LED in the lt MATRIX gt key on the associated status display control panel will light to indicate that the SELECT MATRIX page is active as well as the LED in the numeric keypad corresponding to the currently selected matrix 12 Issue 1 Dec 00 Aurora Status Display User Manual 3 4 3 4 Destination Orientated Status pages 1 1 Description pro bel There are two types of Destination Orientated Status page single level and multi leve l The layout of a sing
25. more diagnostics than can be displayed or not all diagnostics are on display there are more diagnostics than can be displayed on this page MORE 3 9 2 Page Operation Press the lt MATRIX DIAG gt key to select the Matrix Diagnostics page The LED in the lt MATRIX DIAG gt key will light as well as the numeric key LED associated with the currently selected matrix This page allows the User to view the matrix diagnostics for the currently selected matrix There is one Matrix Diagnostics page for each matrix If there are more diagnostics than can be displayed on one page then MORE is displayed in the bottom right hand corner of the page The extra diagnostics cannot be viewed until some of the other diagnostics are cleared 3 9 2 1 Selecting a Matrix Press the numeric key corresponding to the desired matrix to select the Matrix Diagnostics page for that matrix The numeric key LED associated with the newly selected matrix will light Issue 1 Dec 00 Aurora Status Display User Manual pro bel 3 10 Panel Diagnostics Page 3 10 1 Description The layout of the Panel Diagnostics page is shown below pro bel PANEL DIAGNOSTICS MATRIX mmmmmmmmmmmmmmmm PANEL PORT POSN PANEL PORT POSN PANEL PORT POSN PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp
26. nfigured correctly using the Aurora Editors 34 Issue 1 Dec 00 Aurora Status Display User Manual pro bel 5 LED Diagnostics 5 1 Remote Status Display 2411 The 2411 module has 16 diagnostics LEDs D1 D4 labelled 1 16 the functions of which are as follows LEDS 1 8 Indicate 2411 running If the LEDs are cycling backwards and forwards with only one LED lit at any time then the 2411 is running and communication has been established with the Aurora controller If the LEDs are cycling backwards and forwards with all but one LED lit then the 2411 is running but communication has not been established with the Aurora controller LEDS 9 12 Indicate binary representation of multi drop address LED 9 LSB LED 12 MSB ON 1 LED 13 ON Data transmitted to Aurora controller LED 14 ON Data transmitted to Aurora controller LED 15 Not used LED 16 Not used LE 5 2 Status Display Control Panel See 6700 Series control panel handbook for details of diagnostics provided by the 6708 control panel O Issue 1 Dec 00 35 6 6 1 36 Aurora Status Display User Manual pro bel Tie Lines Tie Line Terminology This appendix gives a simple example of the use of Tie Lines and defines some of the terms associated with them Matrix 1 level m Matrix 2 A level n In the example above A tie line connects destination B on matrix 1 Level m to source C on matrix 2 level n Source
27. on Orientated Status pages are used From the destination orientated status page press the lt SETUP gt key to select destination orientated status setup page Both the LEDs in the lt DEST ORIENT gt and lt SETUP gt keys will light to indicate that the setup page is active Also an LED on the Issue 1 Dec 00 Aurora Status Display User Manual pro bel numeric keypad will be lit This indicates either the currently selected matrix or level depending on where the matrix name or levels selected fields are highlighted in inverse video This page had two modes of operation selecting a matrix and editing the levels setup 3 5 2 1 Selecting a matrix Press one of the cursor keys until the matrix name field on the display is highlighted in inverse video Press a numeric key on keypad 1 of the control panel corresponding to the required matrix The matrix name appears in the matrix name field on the display The LED in the associated numeric key for the selected matrix will also light 3 5 2 2 Selecting a Level Field Select the required matrix Select the level posistion to change by pressing one of the cursor keys until one of the level field names is highlighted in inverse video Press the lt SETUP gt key until the required level field is highlighted in inverse video The LED on the numeric keypad associated with the currently selected level will be lit 3 5 2 3 Clearing a level Select the level field that needs to be cleare
28. ontrol panel connects to the system via one of the multidrop device busses The diagram below shows the inter connection AURORA CONTROL FRAME TYPE 6006 MULTI DROP DEVICE BUS 6708 STATUS DIAGNOSTIC CONTROL PANEL Status Display Monitor Issue 1 Dec 00 Aurora Status Display User Manual pro bel Up to 4 additional remote status displays can be connected to the Aurora controller using the Remote Status Display Units see diagram below AURORA CONTROL FRAME TYPE 6006 MULTI DROP DEVICE BUS REMOTE STATUS AND DIAGNOSTIC DISPLAY UNIT TYPE 61 70 CHYRON gt aa 6708 STATUS DIAGNOSTIC isp ay Monitor CONTROL PANEL Note that the RSDU does not necessarily need to be connected to the same multi drop device bus as its associated control panel on the Aurora controller The configuration of each status display and its associated control panel is managed from the Aurora Editors Refer to Appendix A for a description of how to install a status display Each status display provides pages for the following e Destination orientated Status information e Source orientated Staus information e Tie line Status information e Matrix Diagnostic information e Panel Diagnostic information Issue 1 Dec 00 Aurora Status Display User Manual pro bel 2 2 Destination Orientated Status Information The destination orientated status information pages provi
29. prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos Pppppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos Pppppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos PPpppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos Pppppppp prt pos PPPppppp prt pos Pppppppp prt pos Pppppppp prt pos Pppppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos PPPppppp prt pos Pppppppp prt pos PPPppppp prt pos MORE KEY pppppppp Either the name of a missing panel UMD or UNKNOWN if a panel UMD has been connected in an unexpected position prt Panel port number pos Panel position on multi drop chain more Indicates whether there are more diagnostics all diagnostics are on display there are more diagnostics than can be displayed on this page MORE Issue 1 Dec 00 29 30 Aurora Status Display User Manual pro bel 3 10 2 Page Operation Press the lt PANEL DIAG gt key to select the Panel Diagnostics page The lt PANEL DIAG gt key LED will light This page allows the User to view the panel diagnostics There is one Panel Diagnostics page If there are more panel diagnostics than can be displayed on one page then MORE is di
30. splayed in the bottom right hand corner of the page The extra panel diagnostics cannot be viewed until some of the other panel diagnostics are cleared It will indicate positions where the controller expects to see panels UMD s which are missing along with their name If however the controller sees a panel UMD on a port where there are no devices assigned it is reported to the status display as an unknown device Issue 1 Dec 00 Aurora Status Display User Manual pro bel 4 Installation and Troubleshooting 4 1 Introduction This section gives a step by step guide to installing a status display into Aurora Refer to the Aurora Editors Guide 4 2 Aurora Editors e Define a status keypad for the Status Display Control panel if dial up is required for source orientated display e Define a Status Display Control panel referencing the keypad defined in step 1 above e Define either an internal or external Status Display referencing the Status Display Control panel from step 2 above e Allocate the Status Display Control panel to a panel port then drag and drop it onto a device port e If the Status Display is an internal type configure it and leave it in the storeroom e If the Status Display is an external type then drag and drop it onto a device port 4 3 Status Display Unit 6170 e Make sure that EPROM SP92 is fitted to IC7 and EPROM SP93 is fitted to IC6 on the 2411 e Set multi drop address
31. sssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ddddddd DM ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S ssssssss S PG UP PG DN KEY mmmmmmmmmmmmmmmm 11111111 dddddddd SSSSSSSSSS name of the currently selected matrix name of a level selected from the Destination Orientated Setup page a destination association name the name of the source routed on this level of the destination association destination diagnostic T at least one of the destinations in this destination association is an upstream destination of a tie line P at least one level of this destination association is nrotected Issue 1 Dec 00 Aurora Status Display User Manual pro bel association is protected B both of the above none of the above M Marriage indication source routeds are unmarried source routeds are S Source diagnostic T source routed is a downstream source of a tie line U source routed is an upstream source of a tie line P this level is protected B source routed is either a downstream source or an upstream source of a tie line and this level is protected none of the above PG UP Use the lt PAGE UP gt key to access the page s before this one PG DN Use the lt PAGE DOWN gt key to access the page s a
32. t of matrix port and module faults e Panel Diagnostics Page This page provides panel connectivity information Further pages are provided to configure the information displayed and give more detailed information about selected items on the above pages Issue 1 Dec 00 Aurora Status Display User Manual pro bel 3 2 Status Display Control Panel The layout of the 6281 Control panel is given below l Keypad I _ L Keypad 2 Keypad 3 Each of the 3 keypads on the panel perform a different function Keypad 1 is a dual function keypad It is both an editable source keypad and a pre defined numeric keypad The keys are numbered 1 24 for numeric entry purposes see diagram above The source keypad is defined using the Aurora Editors in the usual way Keypad 2 is a pre defined function keypad The layout of this keypad is given below Keypad 2 The top row of keys is used to switch between the different page types The different page types are described in the sections following The bottom row of keys are used to access the modes and functions within the various page types Keypad 3 is a pre defined function keypad The layout of this keypad is given below Keypad 3 Issue 1 Dec 00 11 Aurora Status Display User Manual pro bel 3 3 Select Matrix Page 3 3 1 Description The layout of the SELECT MATRIX page is shown below pro bel SELECT MATRIX 01 mmmmmmmmmmmm
33. ursor and page keys can be used to step through the list of destination associations and select one This is used for the EXTENDED PAGE OPERATION 3 4 1 5 Changing the Levels setup Press the lt SETUP gt key to select the Destination Orientated Setup page Refer to the section which describes the Destination Orientated Setup page 3 4 2 Extended Page Operation 3 4 2 1 Protecting a Destination Association First select the required destination association using the cursor and page keys Now press the lt PROTECT gt key to protect unprotect ALL of the levels of the selected destination association The Status Display Control panel can be configured from the Aurora Editors to be either a master or a normal panel A master panel has no limitations on what it may protect unprotect A normal panel is limited to protecting unprotected outputs or unprotecting outputs that it protected 3 4 2 2 Transferring Sources To examine all of the destinations that a source is routed to first of all select a destination association that the required source is routed to using the cursor and page keys Now press the lt SOURCE ORIENT gt key The Source Orientated Status page is displayed with the source routeds on ALL levels of the selected destination association Issue 1 Dec 00 Aurora Status Display User Manual pro bel In effect the source routeds for the selected destination association have been transferred to the Source Orient
Download Pdf Manuals
Related Search