Manual - Gefen
Contents
1. EDID Mode Local EDID is used instead of the EDID from the display device EDID features newer than HDMI 1 3 are removed when the display is read This provides a general EDID which is compatible with more displays 10 DIP SWITCH CONFIGURATION DIP Switch 2 Hot Plug Detect Default OFF ON HPD Pass Through HPD follows upstream HPD towards the source The HPD signal will reflect the connection status between the display device and the source device If the source or monitor is temporarily disconnected then reconnected there will be a delay of 20 30 seconds before the content is restored to the monitor OFF HPD Always High The HPD signal remains high regardless of the downstream HPD state If the source or monitor does not properly handle HPD no picture after connecting reconnecting source or display set this DIP switch to the OFF position DIP Switch 3 Supports DVI Connections Default ON ON Disable HDCP If a DVI connection is used set DIP to the ON position DVI is supported by disabling HDCP pass through OFF Enable HDCP If an HDMI device is connected set DIP in the OFF position DIP switch is only operational when using Local EDID DIP 1 OFF 11 DIP SWITCH CONFIGURATION IMPORTANT The Green Mode feature on the Receiver unit is A not implemented on hardware versions prior to 9502 Check the hardware version printed on the bottom of the Receiver unit For example the samp2. RS 232 signals to travel along the same Cat 5 cable reducing cabling costs and provid ing easier installation A second Cat 5 cable is used for USB extension How It Works Place the DVIKVM ELR Sender Unit next to the DVI source Use the included DVI cable to connect the computer or other DVI source to the Sender Unit Use the supplied USB cable to connect the USB host source device to the USB port on the Sender Unit Connect the Receiver Unit to the monitor or digital signage display with a DVI cable Connect the USB devices to the Receiver Unit Use two Cat 5 cables up to 330 feet 100 meters to connect the Sender Unit to the Receiver Unit Connect the included locking power supplies to the Sender Unit and Receiver Unit and then connect both power cords to available electrical outlets OPERATION NOTES PLEASE READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVIKVM EXTRA LONG RANGE EXTENDER CAT 5 or CAT 6 cables should not exceed 330 feet 100 meters Shielded STP CAT 5 or CAT 6 is recommended However un shielded UTP CAT 5 or CAT 6 is acceptable NOTE The shielded cable has an advantage by providing immunity to Electromagnetic Interference EMI cell phones and A C motors The GefenToolBox DVIKVM Extra Long Range Extender Over One CAT5 features the ability to generate compatible EDID and Hot Plug signals when working with different brands of source devices and monitors FEATURES Features e Supports DVI
3. option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy u
4. resolutions up to 1920x1200 60 Hz or 1080p at 330 feet 100 meters e Extends USB 2 0 up to 330 feet 100 meters e Supports USB 2 0 480 Mbps e Backward compatible with USB 1 1 devices e Extends Ethernet and RS 232 signals e Works with PC and Mac computers e Locking Power Supplies Wall mountable Package Includes Gefen ToolBox DVIKVM Extra Long Range Extender Sender Unit Gefen ToolBox DVIKVM Extra Long Range Extender Receiver Unit 6 ft DVI Cable M M 6 ft USB cable A B 5V DC Locking Power Supplies Quick Start Guide 7 St Sf St St CON 1 1 1 1 2 1 SENDER UNIT LAYOUT Right Side Left Side SENDER UNIT DESCRIPTIONS USB Link Connector Connects the USB signals from the Sender Unit to the Receiver Unit using CAT CAT 6 cable DVI RS 232 Link Connector Connects the DVI and RS 232 signals from the Sender Unit to the Receiver Unit using CAT 5e CAT 6 cable Ethernet Input Connect a CAT 5 cable from a port on a local Ethernet switch to this jack The DVIKVM ELR supports 10 100BaseT Ethernet 5 V DC Locking Power Connector Connect the included 5 V DC locking power supply to this connector Power Indicator This LED will glow red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available electrical outlet DVI In Connect a DVI cable from the computer to this DVI I
5. Gefen TOOLBOX DVIKVM Extra Long Range Extender GTB DVIKVM ELR GTB DVIKVM ELR BLK User Manual Gern Toni f 4 a A a Dy K 2 A 4 kvm Sal www gefentoolbox com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice DVIKVM Extra Long Range Extender is a trademark of Gefen LLC 2014 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners Rev Ad CONTENTS Introduction Operation Notes Features Sender Unit Layout Sender Unit Descriptions Receiver Unit Layout Receiver Unit Descriptions Connecting and Operating the DVIKVM Extra Long Range Extender DIP Switch Configuration Firmware Update Network Cable Wiring Diagram Mounting Plate Installation Specifications Warranty INTRODUCTION Congratulations on your purchase of the GefenToolBox DVIKVM Extra Long Range Extender Your complete satisfaction is very important to us About Gefen We specialize in total integration for your home theater while also focusing on going above and beyond custo
6. NDER How to Connect the DVIKVM Extra Long Range Extender 1 Connect the computer DVI output to the Sender Unit using the provided DVI cable Connect the monitor to the Receiver Unit using a DVI cable 2 Connect the included USB cable from the computer to the Sender Unit 3 Connect the USB devices to the Receiver Unit 4 Connect the Ethernet port on the Sender Unit to an Ethernet source 5 Connect the Ethernet port on the Receiver Unit to the Ethernet LAN port on the display device 6 Connect the RS 232 ports to the host and display devices 7 Connect CAT 5e or CAT 6 cables between the Link ports on the Sender Unit and the Link ports on the Receiver Unit NOTE If terminating network cables the field please adhere to the TIA EIA568B specification see page 14 5 Connect the 5V DC locking power supplies to the Sender Unit and Receiver Unit Do not overtighten the locking connectors Plug the two 2 AC power cords from the power supplies to available electrical outlets Wiring Diagram for the DVIKVM Extra Long Range Extender Over One CAT5 CAT 5 LINK CABLE ETHERNET Up to 330 ft Gefen TOOLBHX RS 232 CABLE am _ 100BASE T Router USB CABLE mm or Ethernet switch DVI CABLE Sa DVI Source Computer Receiver Sender Monitor or Kiosk Touchscreen Display GTB DVIKVM ELR DIP SWITCH CONFIGURATION Sender Unit The Gefen DVIKVM Extra Long Range Exte
7. connector RS 232 Port Connect a RS 232 Serial Cable from the RS 232 host device to this port USB Indicator This LED glows green when a USB device is connected to the Sender Unit USB In Connects the Sender Unit to the computer using a USB cable RECEIVER UNIT LAYOUT Right Side Left Side RECEIVER UNIT DESCRIPTIONS Remote Ethernet Port Connect a CAT 5 Cable from this jack to the remote device that needs an Ethernet LAN connection Up to 100BaseT speeds are supported DVI RS 232 Link Connector Connects the DVI and RS 232 signals from the Receiver Unit to the Sender Unit using CAT 5e CAT 6 cable USB Link Connector Connects the USB signals from the Receiver Unit to the Sender Unit using a second CAT 5e CAT 6 cable USB Indicator This LED glows green when a USB source is connected to the Receiver Unit USB Output Connectors Connect the USB remote devices such as a keyboard and mouse to these ports RS 232 Port Connect an RS 232 Serial Cable from this port to the device being controlled DVI Out Connect a display to this DVI I connector Power Indicator This LED will glow red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available electrical outlet 5V DC Locking Power Connector Connect the included 5 V DC locking power supply to this connector CONNECTING AND OPERATING THE DVIKVM EXTRA LONG RANGE EXTE
8. le image below indicates hardware version 9401 which does not have the Green Mode feature A d 2 2 9401 o DIP Switch 4 Green Mode Default ON e OFF Enable Green Mode When DIP switch 1 is set to the OFF position the Receiver unit is powered only when is present on the HDMI DVI cable Automatic Power Mode consumes less than 1 Watt of power e ON Disable Green Mode If DIP switch 1 is set to the ON position then the Receiver unit is placed in Power Always Mode In this mode the Receiver unit is always powered 12 FIRMWARE UPDATE Updating the Firmware STOP Before beginning the update process disconnect the Sender unit from the Receiver unit 1 Connect an RS 232 cable from the computer to the Sender Unit 2 Set all DIP switches on the Sender unit to the ON position 3 Connect the 5V DC locking power supply to the Sender Unit 4 Goto the directory where the firmware files are stored 5 Double click the BAT file A screen similar to the following will appear Found sink on port 4 Autodetect platform full sink Autodetect platform spi Autodetect size 128k Erasing Eeprom Done progress 100 Total bytes 38804 Total time 99 906000 seconds Burn succeeded Verifying file progress 100 Total bytes 38804 Total time 88 266000 seconds Verification succeeded 6 Return both DIP switches on the Sender unit to the OFF posi
9. mer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line Please visit http www gefen com for the latest offerings in High Definition signal solutions or call us between the hours of 8 00 am and 5 00 pm Monday Friday Pacific Standard Time for assistance with your A V needs We ll be happy to assist you Why GefenToolBox The GefenToolBox line offers portable and easy to install solutions for common A V system integration setups using DVI and HDMI connectivity GefenToolBox products are wall mountable and small in size GefenToolBox products are easily transported in the field and are ready for immediate and simple installations in working environments These products come finished in a glossy color to blend in with either a white wall or black cabinet The GefenToolBox DVIKVM Extra Long Range Extender The DVIKVM ELR extender extends any DVI Ethernet RS 232 and USB source from a computer to a monitor touch screen display or other digital signage appli cation over a distance up to 330 feet 100 meters using two Cat 5 cables USB 2 0 data rates up to 480 Mbps are supported in addition to backward com patibility with USB 1 1 The Receiver Unit allows the connections of up to two 2 USB devices providing access to printers scanners cameras external storage media digital signage and automated control systems This product uses Gefen ELR technology allowing DVI Ethernet and
10. nder contains DIP switches on the bottom of the Sender Unit Each DIP switch performs a different function Two DIP switches located on the bottom of the Sender Unit DIP Switch 1 Power Management Default ON OFF Enable Green Mode When DIP switch 1 is set to the OFF position the Sender unit is powered only when is present on the HDMI DVI cable Automatic Power Mode consumes less than 1 Watt of power ON Disable Green Mode If DIP switch 1 is set to the ON position then the Sender unit is placed in Power Always Mode In this mode the Receiver unit is always powered DIP Switch 2 RS 232 Mode Default OFF OFF Pass through Mode Pass through mode for RS 232 This is default position ON Firmware Upgrade Mode Firmware Upgrade mode See page 13 for instructions Both DIP switches 1 and 2 must be set to the ON position to perform a firmware upgrade If DIP switch 2 is in the ON position RS 232 cannot be extended DIP SWITCH CONFIGURATION Receiver Unit The Gefen DVIKVM Extra Long Range Extender contains four 4 DIP switches on the bottom of the Receiver Unit Each DIP switch performs a different function Four DIP switches located on the bottom of the Receiver Unit DIP Switch 1 EDID Mode Default OFF e ON Pass Through Mode DDC and HPD are passed through Both the connection status and the full video capabilities of the monitor are used by the source device e OFF Local
11. nder the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 16 MA GTB DVIKVM ELR amp This product uses UL listed CE compliant power supplies 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 WWW gefen com Ex 818 772 9100 E Rev Ad fax 818 772 9120 support gefen com ay
12. o secure the Splitter should undue stress be applied when connecting and disconnecting HDMI cables 15 SPECIFICATIONS oa lis Es ee ee 165 MHz Maximum TWIDS PIKE MG IOCK en 165 MHz DVI Connectors Sender DVI I 29 pin digital only USB Connector Sender Unit cccoocnnoncconcnnnoconcnnncnnaconnnonaconnonanonnnos 1 Type B USB Connectors Receiver Unlit oooccccoconnoncccocconoconnconononnnnononos 2 Type A Link Connectors Sender 04 21 2 RJ 45 Ethernet Connectors Sender 2 RJ 45 1 per unit RS 232 Connector Sender cooonnccccccocncccococonononoconnoconnnnnonarcnnononanos DB 9 female RS 232 Connector DB 9 male 55 292 Baud ea ein 19200 bps Power Supply Sender 5V DC Power CONSUMPIONn een 10 W per unit max Operating 0 40 DIMENSION ae 3 3 W x 6 7 H x 1 2 D SHIPPING NVE cones ea ee 6 Ibs 15 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its
13. tion 7 To update the firmware on the Receiver unit set ALL DIP switches on the Receiver unit to the ON position 8 Connect the 5V DC locking power supply to the Receiver unit 9 Repeat steps 4 and 5 10 The firmware update process is complete 13 NETWORK CABLE WIRING DIAGRAM Gefen recommends the TIA EIA 568 B wiring option Please adhere to the table below when field terminating cable for use with Gefen products Pin Color 2 Orange Blue White Brown White 12345678 CAT 5 CAT 5e and CAT 6 cabling comes in stranded and solid core types Gefen recommends using solid core cabling It is recommended to use one continuous run from one end to the other In some cases connecting through a patch might not work 14 WALL MOUNTING INSTRUCTIONS Gefen TOOLBHX ano 8SN 350H USB Link ano eee sy DVI RS232 Link DVIKVM ELR R DVI RS232 ETHERNET USB ano Ethernet E ca MA The GefenToolBox DVIKVM ELR Sender and Receiver may be mounted vertically in a wall or cabinet with wood drywall screws as shown in the diagram above There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for insertion and retraction of cables at the DVI and RS 232 connectors For installation on a drywall surface use a 6 drywall screw It is recommended when installing on a drywall surface that studs be used t
Download Pdf Manuals
Related Search