User manual - Autoplugin
Contents
1. or turning the ignition to on position enables CIP timers again Additional Functions By default RCP adjusted to perform only basic functions such as start and stop of the heater using the remote control key To turn on the additional functions such as battery monitoring flashing with direction indicators in rearview mirrors etc enter the module into Setup mode and activate corresponding setup item see settings table 3 The buttons of the left hand stalk switch and the brakes pedal are used to enter Setup mode and to change the settings It is necessary to stop the engine and the heater before Turn the ignition on by holding engine start button for at least 2 seconds then press and hold the brakes pedal Rotate the thumbwheel some steps to select idle display in the CIP Then press and hold for at least 5 seconds Read button OK button in some cars while module s LED flashes once a second Both direction indicators in the CIP confirm entering to the setup mode with 2 flashes Release the brakes pedal and Read OK button finally Each setup item in the settings table is a 3 digit code To enter a digit of a code shortly press RESET button so much times as corresponds to a digit The LED and the direction indicators symbols in the CIP confirm each button press the LED briefly goes off the left direction indicator flashes one time when the first or the third digit of code is entered the right direction ind2. 6 1 2 Five flashes with 6 2 Indication of 6 2 1 Off direction command reception 6 2 2 Three flashes indicators in the rearview mirrors from a remote control 6 3 Indication of the heater s operation when starting source is the remote control 6 3 1 Off 6 3 2 On 6 4 Indication of the heater s operation when starting source is the CIP direct or timer start 6 4 1 Off 6 4 2 On 8 Service menu 8 1 Default Settings 8 1 1 Apply factory settings Factory setting Recommended settings marked in Italics _The module turns off the heater if battery s voltage lowers to the adjusted limit Troubleshooting If a run time error occurs during the heater s operation Autoplugin Key informs about the error code with LED flashing The number of flashes corresponds to the error code See table 2 for the error s description and possible solutions Table 2 Error Error Possible Reasons of Solutions Code Description Error Appearance 2 No answer Outer temperature is The heater operates only at from the higher than 15 Celsius temperatures below 15 C It heater degrees is the heater manufacturer s followed the restriction start Fuel level in the fuel Refuel the vehicle command tank is close to empty Fuel Low warning indicator is illuminated in the CIP The heater is blocked Try to start the heater in the after 3 unsuccessful CIP menu If it doesn t star
3. Autoplugin Key V3 Version 9 1 User Manual Rev A Table of Contents Deserplion usas radon ta s Bp B tn an a dou eee ee Module s Possibilities dd eek Package Contents sat tio toda CONNECTION sr ld ies pida Basto Function see A oo op Additional Functions a ee aa ee nee A cates load tebe tase ates s es Glossary CAN Control Area Network digital network for data transfer in vehicles CIP Combined Instrument Panel PCC Personal Car Communicator Description The Autoplugin Key V3 is electronic module designed to add a remote control ability to the fuel fired heater parking heater fuel operated heater pre heater factory installed in Volvo C30 200 2013 S40 200 2012 V50 200 2012 or C70 200 2013 The device is plugged into the OBD II service connector placed on the dashboard and controls the heater via CAN bus Module s Possibilities e Immediate start of the heater with Volvo car s key The remote control key with 5 buttons or the PCC with 6 buttons can be used for the heater control e Immediate stop of the heater with Volvo car s key e Indication of heater s autonomous operation with the direction indicators flashing in the rearview mirrors e Additional protection of the main battery from discharging inspecting voltage level and time of autonomous operation of the heater Package Content 1 Autoplugin Key V3 cartridge 2 User Manual brochure Connection The module needs that 2 ti
4. icator when the second digit of code is entered To complete a digit entering press and release Read OK button The CIP confirms it with one flash of both direction indicators simultaneously When all three digits entered the module checks the code for validity and confirms it with the direction indicators flashing The both direction indicators flash twice simultaneously in case of valid code and flash twice alternately in case of invalid code 5 If entered digit is not correct press and release Read OK button until the module indicates an error Enter the code once more in that case Several codes can be entered without exit of setup mode Turn the ignition off to exit setup mode New settings are saved in the nonvolatile memory of the module and stored there regardless of whether the module is connected or not Note If you start the engine without exit Setup mode new settings will not be saved in memory To reset the module to the factory settings enter the code 8 1 1 Both direction indicators in the CIP should flash three times confirming command execution Then the module exits Setup mode and restarts Settings table 1 Settings Settings Possible Values Group Item 1 1 1 Limitation of 1 1 1 Not adjusted Heater s heater s total 1 1 2 40 minutes operation operational time in 1 1 3 50 minutes time pre heat mode 1 1 4 60 minutes 1 1 5 70 minutes 1 1 6 80 minutes 1 1 7 90 minutes 1 1 8 100
5. mers and direct start stop function for the heater control are present in CIP Therefore it may be necessary to load the special software to the CIP at first by the means of Volvo dealer s equipment Autoplugin Key does not need professional installation Find OBD II service connector at the left lower point of the dashboard The connector is placed near to the handle for bonnet opening Take the module to your hand with the LED oriented closer to the driver s door side and then gently push it to the OBD II connector LED starts flashing for approximately 10 seconds waiting for information from CAN bus Wait until the LED stops flashing before the operation Turn the ignition on if the LED continues flashing after 10 seconds expired Basic Functions 1 A special combination of buttons presses is used to start the heater with the remote control key Firstly press Lamp button on the key to switch on the car s lighting Then press Lock button twice within 30 seconds while lighting is on Every Lock button s pressing is confirmed with direction indicators flashing 2 To stop the heater with the remote control key switch on and then switch off car s lighting twice Intervals between Lamp button presses should not exceed 20 seconds 3 It is possible remotely disable startups of the heater programmed in the CIP Use remote control key to send stop command when the heater is idle Starting the heater any way
6. minutes 1 1 9 120 minutes 1 2 Limitation of 1 2 1 10 minutes heater s 1 cycle 1 2 2 15 minutes operational time in 1 2 3 20 minutes pre heat mode 1 2 4 25 minutes 1 2 5 30 minutes 1 2 6 40 minutes 1 2 7 50 minutes 1 2 8 60 minutes 1 2 9 70 minutes 2 2 1 Lock and 2 1 1 Lock button for the heater start Heater Lamp buttons Lamp button for the heater stop control with functions for the 2 1 2 Lamp button for the heater start remote heater control Lock button for the heater stop control key 2 2 Number of 2 2 1 Combination is disabled sequential Lamp 2 2 2 Four presses button presses for 2 2 3 Six presses the heater control 2 2 4 Eight presses 2 3 Number of 2 3 1 Combination is disabled sequential Lock 2 3 2 Two presses button presses for 2 3 3 Three presses 6 the heater control with the car s lighting turned on 2 3 4 Four presses 3 3 1 3 1 1 Not adjusted Battery Minimal battery 3 1 2 11 8V Monitoring voltage that lets the 3 1 3 11 8V module start the 3 1 4 11 9V heater in pre heat 3 1 5 12 0V mode 3 1 6 12 1V 3 1 7 12 2V 3 1 8 12 3V 3 1 9 12 4V 3 2 3 2 1 Not adjusted Minimal battery 3 2 2 11 4V voltage that lets the 3 2 3 11 5V module keep 3 2 4 11 6V operating the heater 3 2 5 11 7V in pre heat mode 3 2 6 11 8V 3 2 7 11 9V 3 2 8 12 0V 6 6 1 Indication of 6 1 1 Off Indication the heater s startup
7. t starts up make diagnostics of the heater 3 Battery low The module has Charge vehicle s battery with determined that the special charger or start engine battery s voltage is to charge or cancel 3 1 3 2 below the specified by module s settings settings items 3 1 or 3 2 4 Time limits Time limit for Run the engine or cancel 1 1 exceeded autonomous operation of module s settings the heater is achieved 5 Unsuccessful The heater was switched Make diagnostics of the heater start off spontaneously at if the error appears again starting 6 Operation The heater was switched Make diagnostics of the heater cycle too off spontaneously if the error appears again short 8 CAN bus There is a problem with Check for the module s error module s connection to connection the CAN bus 9 Settings error Settings have been Reset the settings 8 1 1 stored in the module s readjust the module memory incorrectly 11 Heater no The heater is unplugged Make diagnostics of the heater connection or out of order Autoplugin ES www autoplugin ru
Download Pdf Manuals
Related Search