User`s manual
Contents
1. Connecting the loudspeaker On the rear side of the WX802 OB is a special waterproof 5 pin connector provided This allows to connect the loudspeaker to the amplifier output A special included connection cable should be used Always connect the white conductor of the connection cable to the COM output of the amplifier and the black connection terminal to the positive terminal of the amplifier output Mind the polarity markings when wiring the loudspeaker cables Power settings The power settings of the WX802 OB can be made by rotating the waterproof connector on the rear side of the loudspeaker On the cable part of the connector is a white dot displayed Depending of the position of the white dot the desired power can be selected The corresponding powers are shown on the sticker on the rear side of the loudspeaker The power impedance of the loudspeaker can be set in 3 adjustable steps of impedance for 100V 60 Watt 30 Watt 15 Watt and 1 step for 16 Ohm standard low impedance applications 1 16 Ohm 70 Watt 2 60 Watt 167 Ohm 3 30 Watt 333 Ohm 4 15 Watt 667 Ohm When the loudspeaker is connected to 70 7V facilities the power indicated in the table above will be reduced to half the power and when connected to 50V facilities the power will be reduced to a quarter When the desired power tap is selected the loudspeaker is ready to be used Additional information WX802 OB Technical specifications RMS Power2. Max Power Nominal Impedance Line transformer power tappings Sound pressure 1W 1m Sound pressure max W 1 m 8 Ohm Sound pressure max W 1 m 100V Frequency response 3 dB Frequency response 10 dB Cross over frequency Horizontal coverage Vertical coverage Drivers Dimensions W x H x D Weight Construction Accessories included Colour Ingress Protection 70 W 140 W 16 Ohm 167 Ohm 60 W 333 Ohm 30 W 667 Ohm 15 W 89 dB 108 dB 106 dB 60 Hz 18 kHz 50 Hz 20 kHz 2400 Hz 110 110 1 HF 8 LF 270 x 360 x 215 mm 7 5 Kg ABS Wall bracket Black IP55
3. Outdoor Wall Speaker WX802 0B PROFESSIONAL AUDIO EQUIPMENT Outdoor Wall Speaker WX802 OB Installation Guide Warning e Only use the correct amplifier output voltage and impedance Exceeding these limits could cause fire or other failures Avoid explosions do not use the speaker around gasoline thinner or other combustibles e Only install the speaker in locations that can structurally support the weight of the speaker Not doing so may result in the speaker falling down e Do not use any other method than specified to mount the speaker If extreme force is applied to the speaker the speaker could fall down e Attach a safety wire to the speaker when it s mounted high above the ground Failure in doing so could cause the speaker to fall down for any reason e Avoid mounting the speaker in locations exposed to constant vibrations The mounting points can be damaged by excessive vibrations potentially causing the speaker to fall down Caution e Avoid electric shocks switch off the amplifier power when connecting the speaker e Avoid installing the speaker in locations exposed to solvents acids smoke and heaters as excessive exposure to these factors could result in speaker failure fire or electric shocks e Do not operate the speaker for an extended period of time at distorted sound This could cause irreparable damage to the speaker e Do not stand or sit on nor hang down from the speaker as this may cause failu
4. re of the speaker Installing the WX802 Mounting the loudspeaker The loudspeaker can be mounted both horizontally and vertically by means of the supplied mounting bracket For mounting the loudspeaker on the desired mounting location the mounting bracket should be removed from the loudspeaker This can be done by loosening the screws on either side of the loudspeaker After this is done the mounting holes should be indicated For a stable mounting of the loudspeaker it should always be fastened by two screws The position of the mounting holes depends of the mounting position horizontally or vertically with a spacing of 248 mm in between After this the bracket can be mounted on the desired location Always use the proper fasteners depending of the mounting surface Once the bracket is mounted on the desired location the loudspeaker can be fixed to the bracket Attention To make sure that no rain or other liquids can enter the loudspeaker when mounted outside a special construction is provided at the inner side of the bass port This construction is only useful when the loudspeaker is mounted in the correct position When the loudspeaker is mounted in horizontal position the loudspeaker must be positioned with the AUDAC logo on the side standing upright in readable position but when the loudspeaker is mounted in vertical position the loudspeaker must be positioned with the tweeter on the top side of the loudspeaker aK
Download Pdf Manuals
Related Search