IV.WIre dIagraM V. PrograMMIng of reMote controls - Net
Contents
1. such along time up to 30 seconds how long you want to hold to the light shining If you press the button during a flash illumination time will be limited Programming Time for 30 seconds will automatically terminate ILSYSTEM INSTALLATION Disassemble plastic cover of dashboard Find wires on control unit whitch control central lock For any vehicle types the central lock connects directly in door of vehicle Use a digital multimeter for function test of wires in the vehicle as well as if you know the function of wire After wires designation disconnect accumulator of vehicle and connect cable tie of the car alarm to wires necessary for correct functionality according to added schemas Solder up all wiring and isolate After finish of the central lock installation connect accumulator of vehicle and plug in a fuse to fuse cover of the central lock Checkout correct functionality of the central lock as well as electrical instalation of vehicle ignition direct indicators plastic cover of car dashboard Fit Control unit location Place the control unit inside of the dashboard Fix antenna of the control unit so that it does not touch of metal parts of the vehicle CONECTOR CN1 14 PIN INPUT AND OUTPUT CONNECTOR Connect wires for central lock control according to type central lock in vehicle and according to wire diagram of central lock connection White blue 300mA Sequential output2. output gt gt gt V PROGRAMMING OF REMOTE CONTROLS Turn on the ignition press the valet switch 5 times and turn off the ignition LED starts to blink rapidly to confirm entry into programming mode Press any button on the remote control within 10 seconds Programming the remote control is confirmed by flashing directional lights 1x for DO1 to DO2 The programming will automatically be terminated within 10 seconds after programming the remote control or turn off the 2 ignition Attention When programming a new remote control is needed to program the remote control in the system already programmed Note The system can be programmed up to 3 or 6 remotes menu 3 VI PROGRAMMING SEQUENTIAI Output 1 Turn on the ignition and press the service button 4 times within 10 seconds 2 Turn on the ignition LED stays lit 3 within 10 seconds press the directional warning lights Directional lights blink 4 when the indicator lights will flash 8 the LED goes out and confirms the successful programming of the output sequence Disabling warning directional lights stop sequence programming output VII PROGRAMMING SYSTEM FEATURES 2 1 Turn on the ignition and press the service button 7 times within 10 seconds K KEETEC 2 Turn off the ignition LED flashes 3 times to confirm entry into the programming of system functions 3 Press the service many times as the number of function you want
3. check the exit tap the lock on the vehicle CHECK LOCK function is optional and registration is disabled Activate the current function by pressing buttons 1 3 two seconds When activated the icon will flash once for lock and unlock and deactivate the function twice If the function is activated the last button pressed you will find a short pressing button 4 When the button is pressed for 0 8 seconds Lights lock or unlock icon depending on which button was pressed last Note When activated LOCK CHECK battery life is shortened in the driver Unlocing Central lock control by positive impulse Low battery driver _ If the push button to lock or unlock the blue flashing battery icon is in the remote bat tery is weak and capacity is needed to be replaced Turn lights on RC MAX Pressing button 4 more than to 1 second to turn the LED on the front of the driver LED lights when you hold the button pressed and after a set period of time off while still holding the button pressed The length of how long the push button LED lights can Angele Before installing read the instructions and recommendations aye Adjusting the length of time switching the light on RC MAX Time how long it has an LED light can be set from 1 30 seconds or indefinitely Si multaneously press buttons 1 and 4 per second The red LED for 3 seconds After the 2 extinction of the flashes in one second intervals During this time press button 4 for
4. on optical signalling output wire Connect sequential output to warning lights switch impulse wire The output is active at lock and unlock of central lock If this output is used then power outputs on direction lights are not need to connect Yellow ignition 12V input wire Violet Trunk open output wire Black skeleton car input wire Violet Trunk open input wire Orange Power output for direction lights output wire Orange Power output for direction lights output wire Red Power supply 12V input wire IILCENTRAL LOCK CONNECTION Direction actuators control o 12V blue blue brown blue orange Locking green brown green white r green orange blue brown blue white ee blue orange green brown green white Unedig green orange 12V Sequential Minus control central locking pulse blue brown blue white isdn blue orange green brown green white nocna green orange Pneumatic central lock connection blue brown Blue white Y Locking Unlocking blue brown green white green orange green brown blue white DIVE Orange white blue output 300mA direction lights ous ices aiden lights ignition yellow 15 input ite eles control input o trunk input L car skelet violet trunk
5. en the ignition key lock press service unlock the central locking Note When disabled F1 and lock the vehicle using the service key in the ignition after shutting down the central locking system is locked by flashing LED Adjustable Disabled TECHNICAL PARAMETERS Power Supply 12V 25 Working Temperature 30 C 70 C Sand by mode Trasfer frequency 433 92 MHz
6. ial output Interval flashing directional lights using sequential output is factory set BATTERY Adjustable Learning sequential output Interval flashing directional lights using sequential output can be set by the vehicle in which the system is fitted IV Programming Sequential Output F3 Number of remotes Default The system can be programmed remotes 6 pcs Adjustable The system can be programmed 3 pcs remote control F4 The polarity of the output sequence Default Continuous output is negative polarity Adjustable Sequential output is positive polarity F5 Sequential Output Type Default Continuous output Adjustable Normal output such as power input on the direction of light F6 Unlocking pulse length Default unlocking pulse duration is 0 5 seconds Adjustable unlocking pulse duration is 3 5 seconds it is not possible to set a double unlock lock pulse F7 Lock pulse length Default pulse length j the same as unlocking pulse Adjustable The length of the lock pulse is 20 seconds can be used to tighten the electrically operated windows extend lock pulse F8 Double pulse lock Default double lock pulse is switched off Adjustable Double lock pulse is switched F9 Double pulse unlock Default A double unlock pulse is switched off Adjustable A double unlock pulse is switched F10 Lock unlock using the service when the ignition key Default Allowed Wh
7. n 1 Lock Turned ignition OFF direction lights flash 1x Button 2 Unlock direction lights flash 2x Button 3 1 sec Trunk open direction lights flash 3x Button 3 2x to 1 sec press 2 x the button 3 to one seconds and activate the LOCK CHECK Each button press is indicated in red flashing LEDs Then the LED flashes green or twice depending on whether you last pressed the button 1 1 flash green or 2 2 flashes green FUNCTION LOCK CHECK This feature allows the user to determine which button on the remote control as the final push This is a key lock unlock and the user can check the exit tap the lock on the vehicle CHECK LOCK function is optional and registration is disabled Button 1 3 Turn on off LOCK CHECK Enabling this function is signaled by a green flashing LED on the remote and turn off flashing red Note When installing in vehicles CZ KEY with manufacturing and immobilizer key is Transponder chip it is necessary to remove the transponder and in the remote controller RC KEY otherwise the car can be started REMOTE CONTROL RC MAX Button 1 Lock Turned ignition OFF direction lights flash 1x Button 2 Unlock direction lights flash 2x Button 3 1 sec Trunk open direction lights flash 3x Button 1 3 Turn on off LOCK CHECK FUNCTION LOCK CHECK This feature allows the user to determine which button on the remote control as the final push This is a key lock unlock and the user can
8. sJ KEETEC CZ 100 CZ KEY CZ MAX control UNIT OF CENTRAL LOCK USER MANUAL E KEETEC contained in the manual Equipment must be installed and used in accordance with these instructions The device is designed for installation in motor vehicles with 12 volt electrical The device must be connected to 12V and negative terminals grounded The manufacturer and retailer are not responsible for any damages resulting from improper installation use operation or control of the product differently from the instructions for use Incorrect repairs to the facility or its treatment are at risk of damage to the equipment or vehicle power supply and loss guarantees For proper operation and flawless product we recommend installation of professional service SYSTEM DESCRIPTION KEETEC CZ 100 CZ KEY is control unit of central lock on remote control for all types engine vehicles with 12V power supply The control unit works with optional central lock also with possibility of trunk control Communication between control unit and remote control is protected by hopping code Control unit contains sequential output on direct indicators that enables direct connection on warning lights impulse wire I REMOTE CONTROL DESCRIPTION REMOTE CONTROL RC KEY Button 1 Lock Turned ignition OFF direction lights flash 1x Button 2 Unlock direction lights flash 2x Button 3 1 sec Trunk open direction lights flash 3x REMOTE CONTROL RC 380 Butto
9. to program After each pressing the LED blinks 1x Where is the serial number of the function 10 press the service button for 3 seconds LED flashes 2x by confirming that you are in programming feature with the order by 10 Where is the serial number of the function 20 press the service button for 3 seconds LED flashes 2 times Again press the service button for 3 seconds LED will blink 2x confirming that you are in programming function with serial number 20 4 After entering the function you want to set the ignition switch Directional lights will flash 1x or 2x depending on how the feature set If you want to continue with the setup function follow from point 2 5 If you want to end programming turn on the ignition and press the button once the service The system terminates the programming Programming table Pm ton cy oee menu 2 mael E o i Go oa Oo o a The polriy ofthe ouput sequence 5 Sequential OuiputType sequence ommal Ce Unlocking pubelengh OS eee 85 ve re Double pulse lock Prchibited Permited Ce Double pulse unlock Prohibited Permited FO Lock unlock using the service when the Prohibited ignition key Feo RESET VIILFUNCTION DESCRIPTION F1 To lock the central locking when the ignition Default When the ignition lock with central locking Adjustable When the ignition with the central locking does not lock F2 Burst mode output Default Fixed sequent
Download Pdf Manuals
Related Search