USB-DA12-8E - ACCES I/O Products, Inc.
Contents
1. All equipment originally manufactured by ACCES which is found to be defective will be repaired or replaced subject to the following considerations Terms and Conditions If a unit is suspected of failure contact ACCES Customer Service department Be prepared to give the unit model number serial number and a description of the failure symptom s We may suggest some simple tests to confirm the failure We will assign a Return Material Authorization RMA number which must appear on the outer label of the return package All units components should be properly packed for handling and returned with freight prepaid to the ACCES designated Service Center and will be returned to the customer s user s site freight prepaid and invoiced Coverage First Three Years Returned unit part will be repaired and or replaced at ACCES option with no charge for labor or parts not excluded by warranty Warranty commences with equipment shipment Following Years Throughout your equipments lifetime ACCES stands ready to provide on site or in plant service at reasonable rates similar to those of other manufacturers in the industry Equipment Not Manufactured by ACCES Equipment provided but not manufactured by ACCES is warranted and will be repaired according to the terms and conditions of the respective equipment manufacturer s warranty General Under this Warranty liability of ACCES is limited to replacing repairing or issuing credit at ACCES discretion for2. External Power Jumper Selection The board requires 5VDC power to operate There are two possible methods for providing the 5V power required 1 Set the jumper to VUSB and allow the USB bus to be the 5V power source This is recommended for low current operations 2 There is a DC DIN input connector for plugging in an external adapter order option PR to receive this regulated adapter included with your shipment To use this option set the jumper to VEXT DC Power Jack This is the DC input connector making it possible to provide a regulated 5V power supply to the card without using the USB bus Be sure to order option PR so this wall adaptor will be included with your shipment Output Voltage Range Jumpers Use the jumpers to select the range that you wish to use Each channel is configured individually for the following output possibilities TE SEENEN Differential Outputs J3 These are the Differential DAC outputs Single Ended Outputs J1 These are the Single Ended DAC outputs USB Connector The USB connector on this board is a USB type B LED Light LED indicates Power and Activity 11 Manual USB DA12 8E Chapter 4 USB Address Information Use the provided driver to access the USB board This driver will allow you to determine how many supported USB devices are currently installed and each device s type This information is returned as a Vendor ID VID Product ID PID and Device Index The board s
3. I O PRODUCTS INC 10623 Roselle Street San Diego CA 92121 Tel 858 550 9559 FAX 858 550 7322 www accesio com 16 Manual USB DA12 8E
4. VID is Ox1605 and its PID is Ox4003 The Device Index is determined by how many of the device you have in your system and provides a unique identifier allowing you to access a specific board at will 12 Manual USB DA12 8E Chapter 5 Programming The installation program on the CD will install four PDF manuals to your hard drive These are the USB I O Quick Start Guide User Manual Software Reference Manual and super software tech manual Vendor Requests Software Reference Manual Details our various drivers and sample programs in a number of programming languages as well as providing insight into the most optimum combination of language environment OS and hardware selection available A search for Product Name will quickly lead you to the relevant sections of this document Vendor Requests This file provides information on a RAW USB INTERFACE for very low level programming generally in Operating Systems other than Windows 13 Manual USB DA12 8E Chapter 6 Connector Pin Assignments Two header connectors provide a means to interface with the on board signals There is a 26 pin header for differential analog outputs and a 16 pin header for single ended analog outputs When ordered as a standard unit no options selected the board is installed in a steel powder coated enclosure with mounted DB25 connectors One ADAP25 screw terminal accessory is included and can be plugged onto the single ended DB25 connector The seco
5. any products which are proved to be defective during the warranty period In no case is ACCES liable for consequential or special damage arriving from use or misuse of our product The customer is responsible for all charges caused by modifications or additions to ACCES equipment not approved in writing by ACCES or if in ACCES opinion the equipment has been subjected to abnormal use Abnormal use for purposes of this warranty is defined as any use to which the equipment is exposed other than that use specified or intended as evidenced by purchase or sales representation Other than the above no other warranty expressed or implied shall apply to any and all such equipment furnished or sold by ACCES 3 Manual USB DA12 8E Table of Contents Chapter 1 Introduction EE 5 Feature Si aeeiiaii iaeaea ied awed VEAN eax EAA VEE AEE EA A VESTEA e aaa 5 lee we 5 EE MEET ee eege eege ege ee ee 5 Model le EE 6 ale Ee EE 6 Included Wwithyour board E 6 Optional Accessories iisen sanie na a a a ai a a aaa imeadid 6 EE en E 6 Chapter 2 Installation 0 cece cece eee eeeeeee eect eter eeeeeeaaaaeeeeeeeeeeeseaeaaaaeeeeeeeeeeeseeeeeeeeeeeeees 8 Software CD TELE 8 Hardware pstaa gegegegegergtege genge Ee gaegE ge ries uniedias anieniaanninrianaMlaninniaaiedian axienadlasienian EE EdEeEEgeE 8 USB VO Quick Start Guide eani inienn iiien nanana aiaa en tens ENNEN ERR spas ENEE EENS aaa KASTA OAA KATERA ANET 8 Chapter 3 Option Selection sco eege 9 E
6. ended to detail the software installation steps The software provided with this board is contained on one CD and must be installed onto your hard disk prior to use To do this perform the following steps as appropriate for your software format and operating system Substitute the appropriate drive letter for your CD ROM or disk drive where you see d in the examples below WIN95 98 Me NT 2000 XP 2003 a Place the CD into your CD ROM drive b The CD should automatically run the install program If the install program does not click START RUN and type d install click OK or press ENTER C Follow the on screen prompts to install the software for this board Hardware Installation The board can be installed in any USB 2 0 or USB 1 1 port Please refer to the USB I O Quick Start Guide which can be found on the CD for specific quick steps to complete the hardware and software installation USB I O Quick Start Guide Provides quick and straight forward steps to complete the software and hardware installation of this product in your system 8 Manual USB DA12 8E Chapter 3 Option Selection Refer to the setup programs on the CD provided with the board Also refer to the Block Diagram and the Option Selection Map when reading this section of the manual p 0 20 0 20 DAC OUTPUT RANGE SELECT FACTORY USE ONLY Figure 3 1 Option Selection Map 9 Manual USB DA12 8E USB DA12 8E Setup Program Output Voltage Ra
7. nd DB25 is the opposite sex of the first to avoid plugging onto the wrong connector which has a different pinout than the first IDC 16 Pin SINGLE ENDED CONNECTOR IDC 16 Pin Header Male ZEISS P GEEEEEEE 45 DACH TT Ground DACA OT Ground DAC 5 Ground DACH LI 8 amp 8 TI Gomm DAC 9 10 TI Grud Table 6 1 J1 Single Ended Analog Outputs 16 Pin IDC Assignments E E DACO Table 6 2 Single Ended Analog Outputs DB25M Connector Pin Assignments 14 Manual USB DA12 8E IDC 26 Pin DB25 DIFFERENTIAL CONNECTOR IDC 26 Pin Header Male a beep ae Function Pin Pin Function DAC 0 1 2 DAC 0 DAC 1 3 4 DAC 1 DAC 2 5 6 DAC 2 Connects to pin 8 7 8 Connects to pin 7 DAC 3 9 10 DAC 3 DAC 4 11 12 DAC 4 DAC 5 13 14 DAC 5 DAC 6 15 16 DAC 6 DAC 7 17 18 DAC 7 N C 19 20 N C N C 21 22 N C N C 23 24 N C Ground 25 26 Ground Table 6 3 J3 Differential Analog Outputs 26 Pin IDC Assignments 2a pact o O O EC 3 paces S O A 4 epes eoms 7 Eo o 10 EC Table 6 4 Differential Analog Outputs DB25F Connector Pin Assignments 15 Manual USB DA12 8E Customer Comments If you experience any problems with this manual or just want to give us some feedback please email us at manuals accesio com Please detail any errors you find and include your mailing address so that we can send you any manual updates Halt CES
8. nge Jumpers B DN 2w EEN Oto 10 z CD BP UNI Use the jumpers to select the range that you wish to use Each channel is configured individually Differential Outputs oO These are the Differential DAC outputs single Ended Outputs Previous Next Done These are the Single Ended DAC outputs Previous Next Done DC Input This is the DC input connector making it possible to provide a ADM power supply to the card without using the USB bus Be sure to use a regulated 5Y power supply For more information refer to the VEXT AVUSB jumper settings External Power Previous Next Done VEXT Taah aahh vo GND a 5V C Extermal Powered Ze USB Bus Powered USB Connector The USB connector on this board is a USB type B socket Previous Next Done LED Light D The USB DA12 84 requires 5 power source to operate There are two possible methods for providing the 5 power required 1 Set the jumper to VUSB and allow the USB bus to be the 5 power source This is recommended for low current operations most applications 2 There is a DC DIN input connector for plugging in an extemal adapter order option P to receive this adapter included with your shipment To use this option set the jumper to VEXT LED indicates Power and Activity Previous Next Done h Previous Next Done Figure 3 2 Setup Program Screen Shot 10 Manual USB DA12 8E
9. ories e ADAP25 M Screw Terminal Adaptor an additional unit could be needed if you intended on using the Single Ended and the Differential Analog Outputs e PH Power Adaptor AC DC 5V regulated if total current gt 500mA e DIN DIN Rail Mounting Provision Specifications Analog Outputs Number of Outputs 8 channels Type of Outputs Single ended or differential Resolution 12 bit resolution Unipolar Ranges 0 2 5V 0 5V 0 10V Bipolar Ranges 2 5V 5V 10V Conversion Rate 5kHz all channels simultaneous Relative Accuracy 2 LSB typical Differential Non linearity 0 2 LSB typical Settling Time 8us typical 10us max Output Current 6mA per channel Bus Type USB2 0 High speed USB1 1 Full speed compatible 6 Manual USB DA12 8E Environmental Operating Temperature 0 to 70 C Storage Temperature 40 to 85 C Humidity 5 to 95 non condensing Board Dimension 3 550 x 3 775 inches Box Dimension 4 x 4 x 1 75 inches tall Power 5VDC provided via USB bus up to 500mA Optional AC DC adapter can be ordered PR option if current use is expected to be greater than what can be supplied by the USB bus Please check to see how much current your USB port can supply and how much current you anticipate using CYPRESS FX2 USB INTERFACE DAC 0 7 SELECT USB 2 0 BUS Figure 1 1 Block Diagram 7 Manual USB DA12 8E Chapter 2 Installation Software CD Installation This paragraph is int
10. tible e Small portable 8 channel 12 bit digital to analog outputs e Double buffered allowing simultaneous update of all DAC s e Computer generated outputs up to 5kHz simultaneous up to 40kHz total e Analog output ranges of 0 2 5V 0 5V 0 10V 2 5V 5V 10V e Single ended and differential outputs on separate connectors e Custom high speed function driver e PC 104 module size and mounting compatibility e Small 4 x4 x1 75 rugged industrial enclosure e DB25M and DB25F enclosure mounted UO connectors Applications e Portable Laptop Education Laboratory e Industrial Automation e Embedded OEM Functional Description This USB product is an ideal solution for adding portable easy to install analog outputs to any computer with a USB port The unit is a high speed USB 2 0 device offering the highest speed available with the USB bus It is fully compatible with both USB 1 1 and USB 2 0 ports The board is plug and play allowing quick connection whenever you need additional I O on a USB port This product features 8 digital to analog converters DACs with both differential and single ended outputs on separate connectors The board features unipolar and bipolar ranges for each DAC giving the user a variety of options The DACs can be updated individually or simultaneously To ensure that there will not be excessive outputs to external circuits when the board is plugged in automatic circuits limit analog outputs to zero vol
11. ts Five Volt 5V Power is supplied to the board either from the USB port via the provided 6 USB cable or an external regulated power supply which powers DC DC converters to provide 12V to the operational amplifiers on the board The I O wiring depends on the model option s ordered For the OEM version connections are via industry standard IDC type 26 pin and 16 pin connectors For full standard versions connections are made to the board via enclosure mounted DB25 connectors with one screw terminal accessory being included model ADAP25 5 Manual USB DA12 8E The product is designed to be used in rugged industrial environments but is small enough to fit nicely onto any desk or testing station The board is PC 104 sized 3 550 by 3 775 inches and ships inside a steel powder coated enclosure with an anti skid bottom Model Options Standard Module installed in an enclosure with two 2 DB25 I O connectors and one 1 screw terminal accessory ADAP25 OEM Board only version with I O headers Special Order Resistors in series with differential connector for impedance matching contact factory with your requirement Included with your board The following components are included with your shipment depending on options ordered Please take the time now to ensure that no items are damaged or missing Standard USB Module ADAP25 Screw Terminal Adaptor qty 1 6 USB cable Software Master CD USB I O Quick Start Guide Optional Access
12. xternal Power Jumper Selection ee beeetie reest eeteeeg eebe bag erg 11 DG Power Jack eer sg erg giereg 11 Output Voltage Range Jumpers kk EEEN ERKENNEN EEN EEN EEN 11 Differential Outputs J3 Ee 11 Singl End d O tp ts EE 11 USB EEN 11 EREM 11 Chapter 4 USB Address Information neeooeennnnneeeeeeeeeenrrrrrrteeserrrrrrnnnrnseeerrnnnnnnnensereenna 12 Chapter 5 road 13 Software Reference Manual wiscccascisecsiccdiueiiendvencduedionusecaduveinadieccdiedinwuiecdieceiteddentieudivecaentuereanes 13 Vendor ROGUESISs ea E a 13 Chapter 6 Connector Pin Assignments 0 ccccccceeceeceeceeeeeeeeeeeeeeeenneeeeeeeeeeeeeeeeeaaees 14 List of Figures eE BOCK CHARA EE 7 Figure 3 1 Option Selection Map veiiiersiecsseeccced tected eve ENNEN ENNEN ENEE ENEE ENNEN ERKENNEN EEN ENNEN EEN EN 9 Figure 3 2 Setup Program Screen hot 10 List of Tables Table 6 1 J1 Single Ended Analog Outputs 16 Pin IDC Assignments s ssssssessesssensenesrnrnnerrnnnnnnrnnnnnnne 14 Table 6 2 Single Ended Analog Outputs DB25M Connector Pin Assignments cceceeeeeeeeeeeeeeeeeeeeeeeeee 14 Table 6 3 J3 Differential Analog Outputs 26 Pin IDC Assignments ssssseernestneerrrerrneernrenrreernrennrennne 15 Table 6 4 Differential Analog Outputs DB25F Connector Pin Assignments s sanno1noa1nannnnnnnnnnnnnnnnnene 15 4 Manual USB DA12 8E Chapter 1 Introduction Features e High speed USB 2 0 device USB 1 1 compa
13. ya ACCES I O PRODUCTS INC 10623 Roselle Street Se n Diego CA 92121 e 858 550 9559 FAX 858 550 7322 ntactus accesio com www accesio com MODEL USB DA12 8E Eight Channel Digital to Analog Converter USER MANUAL FILE MUSB DA12 8E B1j Notice The information in this document is provided for reference only ACCES does not assume any liability arising out of the application or use of the information or products described herein This document may contain or reference information and products protected by copyrights or patents and does not convey any license under the patent rights of ACCES nor the rights of others IBM PC PC XT and PC AT are registered trademarks of the International Business Machines Corporation Printed in USA Copyright 2005 2007 by ACCES UO Products Inc 10623 Roselle Street San Diego CA 92121 All rights reserved WARNING ALWAYS CONNECT AND DISCONNECT YOUR FIELD CABLING WITH THE COMPUTER POWER OFF ALWAYS TURN COMPUTER POWER OFF BEFORE INSTALLING A CARD CONNECTING AND DISCONNECTING CABLES OR INSTALLING CARDS INTO A SYSTEM WITH THE COMPUTER OR FIELD POWER ON MAY CAUSE DAMAGE TO THE I O CARD AND WILL VOID ALL WARRANTIES IMPLIED OR EXPRESSED 2 Manual USB DA12 8E Warranty Prior to shipment ACCES equipment is thoroughly inspected and tested to applicable specifications However should equipment failure occur ACCES assures its customers that prompt service and support will be available
Download Pdf Manuals
Related Search