ET08 / ET081 - Total Protection
Contents
1. 2000 2600 2000 2600 161715 L4 RING TIP 1 DC COM N A N A Z1 Ho H 0o 200 eee RING TIP AUX AUX ALARM SYSTEM Fig No 17 1 Connect the circuit as indicated in Fig No 17 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L3 L4 contacts to landline PSTN 3 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 4 Set the jumpers on B1 B2 SET and MODE pins See Fig No 18 for correct jumper position 81 82 QED SET MODE O PROG Fig No 18 A FOR ADVANCED USERS ONLY A 4 9 Communication Mode 9 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using GSM Audio Channel as Backup Connection In this mode the communicator retransmits alarm system Contact ID or 4 2 data to monitoring station via landline PSTN through private branch exchange station PBX The communicator also monitors the voltage dial tone monitoring optional on the exter nal PSTN In case the external PSTN is unavailable disconnected or cut off voltage drops below 4V the system e switches to backup connection GSM audio channel e notifies monitoring station about PSTN failure e continues transmitting data to monitoring station via GSM audio channel until the external PSTN is restored NOTE Notification about PSTN2. lt zZ gt O U ETO8 ET081 User Manual v1 2 Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around Dx ee GSM communicator 08 081 further referenced as system or device contains a radio transceiver operating in GSM850 900 1800 1900 bands DO NOT use the system where it can interfere with other devices and cause any potential danger DO NOT use the system with medical devices if this is required in the manual of the medical device DO NOT use the system in hazardous environment DO NOT expose the system to high humidity chemical environment or mechanical impacts DO NOT attempt to personally repair the system System labelling sticker is at the bottom of the device System 5 8 ET081 is a device mounted in limited access areas Any system repairs must be done only by qualified safety aware personnel Mains power must be disconnected before any installation or tuning work starts The system installation or maintenance must not be done during stormy conditions The system must be powered by main 10 24V ZZZ 300mA power supply which must be approved by LST EN 60950 1 stan dard and be easily accessible Any additional devices linked to the system ET08 ET081 computer sensors relays etc must be approved by LST EN 60950 1 standard External power supply can be connected to AC mains only inside i
3. Technical Specifications 2 1 Electrical amp Mechanical Specifications 2 2 Main Unit Connector Pin amp LED Functionality 2 2 1 Main Unit Functionality 2 2 2 Connector Functionality 2 2 3 Pin Functionality 2 2 4 LED Functionality 2 3 Connection Circuit 1513119110 22 5 52 2 5 8 Communication MOES cssssessssessssssssessssessesessesssesessesesseces 9 4 1 Communication Mode 1 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel 9 4 2 Communication Mode 2 Data Transmission from Alarm System to Preset User 5 Dy 4 4 4 44 4 66655 66 59095 10 4 3 Communication Mode 3 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel and SMS Messages to Preset User 11 4 4 Communication Mode 4 Data Transmission from Alarm System to Monitoring Station via GPRS Network 12 4 5 Communication Mode 5 Data Transmission from Alarm System to Monitoring Station via PSTN using GSM Audio Channel as Backup Connection 13 4 6 Communication Mode 6 Data Transmission from Alarm System to Monitoring Station via PSTN using SMS Messages as Backup Connection 14 4 7 Communication Mode 7 Data Transmission from Alarm System to Mo
4. Received SMS message Incorrect Format or Command is not correct Incorrect syntax Extra lt space gt character is left in SMS message For product warranty repair service please contact your local retail store where this product was purchase If your problem could not be fixed by the self guide above please contact your distributor or ELDES technical support by email support eldes It More up to date information about your device and other products can be found at the manufacturer s website www eldes It USER MANUAL ELDES ET08 ET081 V1 2 25 For notes 26 For notes USER MANUAL ELDES ET08 ET081 V1 2 27 Made in Lithuania www eldes lt
5. RING TIP to RING TIP con tacts of the communicator 2 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 3 Set the jumper on MODE pins See Fig No 6 for correct jumper position 81 82 OO O O O SET MODE PROG Fig No 6 4 3 Communication Mode 3 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel and SMS Messages to Preset User s In this mode the communicator retransmits Contact ID data sent from alarm system to monitoring station via GSM audio channel In addition the data is duplicated and decoded data to user understandable text format and sent to preset user s by SMS mes sage There is NO backup connection for this mode NOTE User phone number s must be set for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details 00 0 2000 00 0 00 0 11 12 13 L4 RING TIP C1 DC COM N AN A 21 oe RING TIP AUX AUX ALARM SYSTEM Fig No 7 1 Connect the circuit as indicated in Fig No 7 connect telephone contacts of the alarm system RING TIP to RING TIP con tacts of the communicator 2 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 3 Set the jumper on SET pins See Fig No
6. continues transmitting data to monitoring station via GSM audio channel until the PSTN is restored duplicates and decodes data to user understandable text format and sends it to preset user s by SMS message until the PSTN is restored NOTE User phone number s must be set and notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details for more details 200 200 000 200 REEDE L4 RING TIP C1 DC COM N A N A Z1 H H 60 200 RING TIP AUX ALARM SYSTEM Fig No 15 1 Connect the circuit as indicated in Fig No 15 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L3 L4 contacts to landline PSTN 3 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 4 Set the jumpers on B1 B2 and SET pins See Fig No 16 for correct jumper position B1 B2 ae Lu 0Y oO ase Fig No 16 USER MANUAL ELDES ET08 ET081 V1 2 45 4 8 Communication Mode 8 Data Transmission from Alarm System to Monitoring Station via PSTN using GPRS Network as Backup Connection In this mode the communicator retransmits Contact ID data via landline PSTN sent from alarm system to monitoring station The communicator also monito
7. the system will redu ce the risk of fire theft burglary or other dangers but does not guarantee against such events EL DES UAB will not take any responsibility regarding personal property or revenue loss while using the system ELDES UAB responsibility according to local laws does not exceed value of the purchased system ELDES UAB is not affiliated with GSM ope rators providing cellular services therefore is not responsible for network services coverage or its operation Manufacturer Warranty The system carries a 24 month warranty by the manufacturer ELDES UAB Warranty period starts from the day the system has been purchased by the end user The warranty is valid only if the system has been used as inten ded following all guidelines listed in the manual and within specified operating conditions Receipt with purchase date must be kept as a proof The warranty is voided if the system has been exposed to mechanical impacts chemicals high humidity fluids corrosive and hazardous environ ment or other force majeure factors Package Content 1 System ET08 ET081 2 5 08 ET081 user manual 3 GSM antenna 5 Fastening holders About User Manual This document describes communicator ET08 081 its operation and installation It is very im portant to read User Manual before start using the system CONTENTS 1 General Information 1 1 Operation Description
8. 2000 11 12 13 14 RING TIP C1 DC COM N AN A 21 00 00 RING TIP AUX AUX ALARM SYSTEM Fig No 3 1 Connect the circuit as indicated in Fig No 3 connect telephone contacts of the alarm system RING TIP to RING TIP con tacts of the communicator 2 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 3 No jumpers have to be set on any pins See Fig No 4 for correct jumper position 81 82 Fig No 4 USER MANUAL ELDES ET08 ET081 V1 2 9 4 2 Communication Mode 2 Data Transmission from Alarm System to Preset User s by SMS In this mode the communicator retransmits Contact ID data sent from alarm system and decodes it to user understandable text format which is sent to preset user s by SMS message There is NO backup connection for this mode NOTE User phone number s must be set for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details ATTENTION It is also necessary to set monitoring station phone number on alarm system in this mode In such case you can use any number one digit is enough 00 0 000 000 0000 L1 12 13 L4 RING TIP C1 DC COM N AN A 21 00 oO RING TIP AUX AUX ALARM SYSTEM Fig No 5 1 Connect the circuit as indicated in Fig No 5 connect telephone contacts of the alarm system
9. 8 for correct jumper position 81 82 OO O SET O MODE O 806 Fig No 8 USER MANUAL ELDES ET08 ET081 V1 2 11 4 4 Communication Mode 4 Data Transmission from Alarm System to Monitoring Station via GPRS Network NOTE EGR100 software is required for this communication mode The software is freeware and can be downloaded from ELDES website at www eldes It In this mode the communicator retransmits Contact ID data via GPRS network sent from alarm system to monitoring station There is NO backup connection for this mode I The following communicator GPRS settings must be set up using ELDES Configuration Tool software CID over GPRS Enabled enables Contact ID data transmission via GPRS network APN access point name provided by GSM operator User Name user name provided by GSM operator Password password provided by GSM operator Server IP external IP address of the computer router running EGR100 software Server Port forwarded UDP port for the computer running EGR100 software Please refer to ELDES Configuration Tool software s HELP section for more details The following settings must be set up in EGR100 software e TCP UDP Server Port forwarded port for communication with the device via GPRS Please refer to EGR100 software s user guide for more details NOTE UDP port must be set the same both on the communicator using ELDES
10. Configuration Tool and in EGR100 software 00 0 2000 2000 000 11 12 13 L4 RING TIP C1 DC COM N AN A 21 Ooo oo RING TIP AUX AUX ALARM SYSTEM Fig No 9 1 Connect the circuit as indicated in Fig No 9 connect telephone contacts of the alarm system RING TIP to RING TIP con tacts of the communicator 2 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 3 Set the jumpers on SET and MODE pins See Fig No 10 for correct jumper position 81 82 OO O SET MODE O PROG Fig No 10 4 5 Communication Mode 5 Data Transmission from Alarm System to Monitoring Station via PSTN using GSM Audio Channel as Backup Connection In this mode the communicator retransmits Contact ID and 4 2 data via landline PSTN sent from alarm system to monitoring sta tion The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable disconnected or cut off voltage drops below 4V the system e switches to backup connection GSM audio channel e notifies monitoring station about PSTN failure e continues transmitting data to monitoring station via GSM audio channel until the PSTN is restored NOTE Notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Conf
11. Monitoring Station via PSTN through PBX using GSM Audio Channel as Backup Connection and SMS Messages to Preset User s In this mode the communicator retransmits alarm system Contact ID data to monitoring station via landline PSTN through pri vate branch exchange station PBX The communicator also monitors the voltage dial tone monitoring optional on the external PSTN In case the external PSTN is unavailable disconnected or cut off voltage drops below 4V the system switches to backup connection GSM audio channel notifies monitoring station about PSTN failure sends an SMS report to the preset user s on PSTN failure continues transmitting data to monitoring station via GSM audio channel until the external PSTN is restored duplicates and decodes data to user understandable text format and sends it to preset user s by SMS message until the external PSTN is restored NOTE User phone number s must be set and notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details 000 000 1615 14 RING TIP 1 DC COM N A N A 1 To external landline PSTN 60 Oo RING TIP AUX AUX ALARM SYSTEM Fig No 23 internal landline PSTN Connect the circuit as indicated in Fig No 23 connect telephone contacts o
12. STN is restored NOTE User phone number s must be set for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details O00 200 000 200 EQ 253 L4 RING TIP 1 DC COM N A N A Z1 660 60 Telandine RING TIP AUX AUX ALARM SYSTEM Fig No 13 1 Connect the circuit as indicated in Fig No 13 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L3 L4 contacts to landline PSTN 3 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 4 Set the jumpers on B1 B2 and MODE pins See Fig No 14 for correct jumper position 81 82 ae Llu 0Y OoOO 4 RE Fig No 14 4 7 Communication Mode 7 Data Transmission from Alarm System to Monitoring Station via PSTN using GSM Audio Channel as Backup Connection and SMS Messages to Preset User s In this mode the communicator retransmits Contact ID data via landline PSTN sent from alarm system to monitoring station The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable discon nected or cut off voltage drops below 4V the system switches to backup connection GSM audio channel notifies monitoring station about PSTN failure sends an SMS report to the preset user s on PSTN failure
13. TN is unavailable disconnected or cut off voltage drops below 4V the system e sends an SMS report to the preset user s on PSTN failure e decodes data to user understandable text format and continues transmitting it to preset user s by SMS message until the external PSTN is restored NOTE User phone number s must be set and notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details 000 000 2000 000 1 181 2127 14 RING TIP C1 DC COM N A N A 1 To external landline PSTN 00 RING TIP AUX AUX ALARM SYSTEM 7 Internal Fig No21 andline PSTN Connect the circuit as indicated in Fig No 21 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator Connect L1 L2 contacts to external landline PSTN Connect L3 L4 contacts to internal landline PSTN of PBX Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system Set the jumper on MODE pins See Fig No 22 for correct jumper position uw PF wD 81 OO N O O SET MODE O PROG Fig No 22 A FOR ADVANCED USERS ONLY A 4 11 Communication Mode 11 Data Transmission from Alarm System to
14. a lt konm SMS text XXXX_ON thstuncionswitchestheoutor O function switches the thstuncionswitchestheoutor O OFF SMS text a XXXX_OFF This function switches the output ON for a set period of time and switches the output back to OFF after the set period of time is over SMS text g XXXX_ON_T Value T period of time in seconds range 1 9999 This function switches the output OFF for a set period of time and switches the output back to Output Pulse ON Output Pulse OFF ON after the set period of time is over a SMS text XXXX_OFF_T Value T period of time in seconds range 1 9999 Pa The delay period of time between telephone line failure and restore events If telephone line failure and restore events occur before the set delay period of time is over the system will not send the SMS report Telephone Line Failure Restore Delay SMS text g XXXX_TELDLY T Value T period of time in seconds range 1 250 USER MANUAL ELDES ET08 ET081 V1 2 23 6 Appendix 6 1 Restoring Default Parameters To restore the default parameters Disconnect the power supply Short circuit connect DEFAULT pins Power up ET08 ET081 for 7 seconds Disconnect the power supply Remove short circuit from DEFAULT pins Parameters restored to default OW GTR 6 2 Upgrading Firmw
15. are 6 Disconnect the power supply and backup battery Short circuit connect DEFAULT pins Connect the device via USB cable to the PC Power up the device The new window must pop up where you will find the bin file Otherwise open My Computer and look for Boot Disk drive Delete the bin file found in the drive Copy the new firmware bin file to the very same window Power down the device 9 Unplug USB cable 10 Remove short circuit from DEFAULT pins 11 Power up the device 12 Firmware upgraded Oi GOINGS SS NOTE It is strongly recommended to restore default parameters after the firmware upgrade 3 ELDES Configuration Tool Software To configure the system please install configuration software ELDES Configuration Tool which can be downloaded from ELDES website at www eldes It Before connecting USB cable to the computer please read ELDES Configuration Tool user guide available in the HELP section of the software 24 6 4 Technical Support Indication Possible Reason GSM LED is off or not flashing No external power supply Circuit not properly connected Blown fuse No GSM network signal STATUS LED flashing several times per second SIM card not inserted improperly inserted PIN code enabled SIM card inactive System does not send any SMS messages SIM card credit limit exceeded Incorrect SMS centre phone number No GSM network signal User phone number is not preset
16. ect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 5 Set the jumper on SET and MODE pins See Fig No 26 for correct jumper position B1 B2 OO OO Hoe O No 26 USER MANUAL ELDES ET08 ET081 V1 2 21 5 SMS Commands only in ET081 ATTENTION In this user manual the underscore _ character represents one lt space gt character There must be no spaces or other characters at the beginning and at the end of the message XXXX 4 digit SMS password In order to configure and control 5 081 system using SMS message send the text command to ET081 SIM card phone number from one of the authorized phone numbers The structure of SMS message consists of 4 digit SMS password the default SMS pass word is 0000 four zeros the command and the parameters For some commands the parameters are not applied i e STATUS ET081 notifies the user if a mistake was made in SMS command Command is not correct me SMS report indicating information on system input and output status SMS text XXXX_STATUS 5 The 4 digit SMS password intended for system configuration and control via SMS messages Password Manufacturer default SMS password is 0000 four zeros which is NECESSARY to change gt SMS text 0000_PSW_XXXX Value XXXX new 4 digit password a This function switches the output ON G
17. f alarm system unit if PGM output is im plemented as open collector circuit or any other circuit and if it commutes with COM ETO8 ET081 It is also possible to connect motion sensor or any other sensor to ET081 Z1 input 21 IDC COM 1 ET081 C1 output can be connected to input of electronic appliance and if it commute with COM This connection allows to control heating lighting gates blinds water pump etc W9d 12V Alarm system Fig No2 ou or other appliance only in ET081 USER MANUAL ELDES ET08 ET081 V1 2 3 Installation NOTE Due to GSM network characteristics it is recommended that ET08 ET081 be equipped with a SIM card from the same GSM operator who provided the SIM cards used by users who will receive messages from the system Thus you will ensure the quickest SMS message delivery and receipt NOTE To ensure maximum system operation reliability we recommend not to use pay as you go SIM cards If the balance is insufficient the system will not be able to inform users by SMS or send Contact ID messages IMPORTANT Power supply at alarm system must be disconnected before any installation or tuning work The system can be installed in a metal or non flammable plastic enclosure together with alarm control panel When the metal enclosure is also used it is necessary to ground the enclosure using yellow green colour cable For the connection use 0 50 mm 1 thread cab
18. f the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L1 L2 contacts to external landline PSTN 3 Connect L3 L4 contacts to internal landline PSTN of PBX 4 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 5 Set the jumper on SET pins See Fig No 24 for correct jumper position 81 82 OO L 0Y oQ ase OJO OJO Fig No24 USER MANUAL ELDES ET08 ET081 V1 2 19 A FOR ADVANCED USERS ONLY A 4 12 Communication Mode 12 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using GPRS Network as Backup Connection In this mode the communicator retransmits alarm system Contact ID data to monitoring station via landline PSTN through pri vate branch exchange station PBX The communicator also monitors the voltage dial tone monitoring optional on the external PSTN In case the external PSTN is unavailable disconnected or cut off voltage drops below 4V the system e switches to backup connection GPRS network e notifies monitoring station about PSTN failure e continues transmitting data to monitoring station via GPRS network until the external PSTN is restored NOTE Notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details I The following c
19. icator ET08 ET081 is a device for transmitting data from alarm system to monitoring station via GSM audio channel GSM audio channel and or to users via SMS message Telehone landline PSTN GPRS network The system can be used in the following applications Property security GSM network backup for PSTN 1 1 Operation Description ET08 ET081 communicator acts as a gateway between the alarm system and monitoring station providing a dial tone and fully replacing the landline PSTN The communicator notifies monitoring station ET081 ONLY and or the preset user by SMS message in case PSTN is unavailable has been cut off or disconnected by PSTN provider ET08 ET081 supports only outgoing calls DTMF number dialing mode in alarm system must be enabled ET08 ET081 can detect temporary service suspension by the service provider for technical or billing reasons even if a dial tone is still present optional feature ET08 ET081 features several communication ways between alarm system and monitoring station via 1 GSM audio channel 2 PSTN using GSM audio channel as backup connection 3 SMS messages to preset users 4 PSTN using GSM audio channel as backup connection with data duplication to preset users via SMS 5 GPRS network 6 PSTN using GPRS network as backup connection Please refer to chapter 4 Communication Modes for more details The system ET08 ET081 has 1 digital input normally open for
20. iguration Tool Please refer to software s HELP section for more details 200 2600 2000 000 Ej ha ke L4 RING TIP 1 DC COM N A N A Z1 HH 260 To lafidline RING TIP AUX ALARM SYSTEM Fig No 11 1 Connect the circuit as indicated in Fig No 11 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L3 L4 contacts to landline PSTN 3 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 4 Set the jumpers on B1 and B2 pins See Fig No 12 for correct jumper position B1 B2 a wi oY rk oQ ase 21210 Fig No 12 USER MANUAL ELDES ET08 ET081 V1 2 13 4 6 Communication Mode 6 Data Transmission from Alarm System to Monitoring Station via PSTN using SMS Messages as Backup Connection In this mode the communicator retransmits Contact ID data via landline PSTN sent from alarm system to monitoring station The communicator also monitors the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable discon nected or cut off voltage drops below 4V the system 9 sends an SMS report to the preset user s on PSTN failure e decodes data to user understandable text format and continues transmitting it to preset user s by SMS message until the P
21. is indicated by GSM LED To ensure the best quality of the network adjust the position of GSM antenna and find the strongest possible signal by observing the GSM LED indications GSM LED Indication GSM Signal Strength Off No connection Flashing every 3 seconds Flashing every 1 second The connection is not reliable Satisfactory Flashing several times per second On It is recommended to install the GSM antenna away from the alarm system to ensure better quality of the audio signal It is not Good Excellent recommend to install the antenna inside the metal enclosure a There are also a few other indicators device activity indicator STATUS and working mode indicator INFO Device Activity Indication STATUS LED Indication Meaning Off No power supply or some fault is present Flashing several times per second SIM card is not inserted insterted improperly On Device is operating and ready for use Working Mode Indication INFO LED Indication Meaning Device is in standby mode Flashing several times Device retransmits the data sent from alarm system to the monitoring station this per second indication is possible when device is operating in communication mode 1 On Device is decoding Contact ID data to user understandable text format 2 3 Connection Circuit COM connectors of ET08 ET081 and alarm system unit must be connected ET081 Input Z1 is connected to PGM output o
22. le Device Installation and Pre operation l 2 Fasten the system in the enclosure using fastening holders Place SIM card into the SIM card slot and fix it with holder after making sure that SIM card PIN code is disabled PIN code can be disabled by inserting the SIM card into mobile phone and following proper menus SIM card should not have any remaining SMS messages Connect the GSM antenna to SMA connector It is not recommended to turn on the device without GSM antenna connec ted Connect the circuit according to desired communication mode see chapter 4 Communication Modes The system should start in less than a minute GSM LED indicator should be blinking or be ON indicating successful con nection to GSM network 4 Communication Modes ATTENTION DTMF phone number dialing mode must be enabled on alarm system activated Contact ID or 4 2 data transmission protocol and monitoring station phone number set with international code i e For UK London 20xxxxxxxx or 004420xxxxxxxx The lt plus gt character is not allowed 4 1 Communication Mode 1 Data Transmission from Alarm System to Monitoring Station via GSM Audio Channel In this mode the communicator retransmits Contact ID or 4 2 data sent from alarm system to monitoring station via GSM audio channel There is NO backup connection for this mode NOTE No additional communicator configuration is required for this mode 2000 00 2000
23. loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details 2000 00 000 000 11 L2 3 14 RING TIP 1 DC COM N AN A Z1 To external landline PSTN RING TIP AUX AUX ALARM SYSTEM Fig No 19 Internal landline PSTN Connect the circuit as indicated in Fig No 19 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L1 L2 contacts to external landline PSTN 3 Connect L3 L4 contacts to internal landline PSTN of PBX 4 Connect power supply to DC COM contacts Power supply is usually used as AUX and AUX output of alarm system 5 No jumpers have to be set on any pins See Fig 20 for correct jumper position B1 B2 OO OO lu 0Y OoOO ase OJOO OJO O Fig No20 USER MANUAL ELDES ET08 ET081 V1 2 17 A FOR ADVANCED USERS ONLY A 4 10 Communication Mode 10 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using SMS Messages as Backup Connection In this mode the communicator retransmits alarm system Contact ID data to monitoring station via landline PSTN through pri vate branch exchange station PBX The communicator also monitors the voltage dial tone monitoring optional on the external PSTN In case the external PS
24. ne 350 Hz only in ET081 4 2 protocol operates in communication mode 1 5 and 9 ONLY via GSM audio channel 2 2 Main Unit Connector Pin amp LED Functionality For configurations SIM CARD 2000 14 RING TIP 000 1 DC COM 2000 N A N A Z1 1109012915 USB NFO STATUS O GM O USER MANUAL ELDES ET08 ET081 V1 2 2 2 1 Main Unit Functionality GSM MODEM GSM network 850 900 1800 1900 MHz modem SIM CARD SIM card slot holder ANT GSM antenna SMA type connector Fl Fuse model miniSMDC 500mA USB Mini USB port 2 2 2 Connector Functionality Labelling Description L1 L4 Landline or PBX contacts according to backup mode RING RING contact TIP TIP contact C1 Output DC Positive power supply contact COM Negative power supply contact Common contact Input N A Not available 2 2 3 Pin Functionality Labelling Description DEFAULT For restoring factory default settings SET For enabling communication modes MODE For enabling communication modes 81 82 For communication backup connection PROG Not used 2 2 4 LED Functionality Labelling Description INFO Working mode indicator STATUS Device activity indicator GSM GSM network quality indicator GSM Signal Strength Indication GSM signal strength
25. nitoring Station via PSTN using GSM Audio Channel as Backup Connection and SMS Messages to Preset User 4444 6666956559 15 4 8 Communication Mode 8 Data Transmission from Alarm System to Monitoring Station via PSTN using GPRS Network as Backup 16 4 9 Communication Mode 9 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using GSM Audio Channel as Backup Connection 17 4 10 Communication Mode 10 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using SMS Messages as Backup Connection 18 4 11 Communication Mode 11 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using GSM Audio Channel as a Backup Connection and SMS Messages to Preset User 19 4 12 Communication Mode 12 Data Transmission from Alarm System to Monitoring Station via PSTN through PBX using GPRS Network as Backup 20 SMS COMME 36 22 Appendix 6 1 Restoring Default Parameters 6 2 Upgrading Firmware 6 3 ELDES Configuration Tool Software 6 4 Technical Support 1 General Information Commun
26. ns tallation room with automatic 2 pole circuit breaker capable of discon Phase necting circuit in the event of short circuit or over current condition Open circuit breaker must have a gap between connections of more than 3mm and the disconnection current is 5A AC 230V 50 Hz DC 24V USB cable Fuse F1 model miniSMDC 500mA Blown fuse cannot be replaced by the user and the replacement fuses have to be exactly the same as indicated by the manufacturer The device is fully turned off by disconnecting 2 pole switch off device of the external power supply or any other linked device that the system ET08 ET081 is powered from The WEEE Waste Electrical and Electronic Equipment marking on this product see left or its documentation indicates that in the EU the product must not be disposed of together with household waste Copyright ELDES UAB 2011 All rights reserved It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from ELDES UAB ELDES UAB reserves the right to update or modify this document and or related products without a warning Hereby ELDES UAB declares that this communicator ET08 ET081 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www eldes It Limited Liability The buyer must agree that
27. ommunicator GPRS settings must be set up using ELDES Configuration Tool software e CID over GPRS Enabled enables Contact ID data transmission via GPRS network e APN access point name provided by GSM operator User Name user name provided by GSM operator e Password password provided by GSM operator e Server IP external IP address of the computer running EGR100 software e Server Port forwarded UDP port for the computer running EGR100 software Please refer to ELDES Configuration Tool software s HELP section for more details Il The following settings must be set up in EGR100 software e TCP UDP Server Port forwarded port for communication with the device via GPRS Please refer to EGR100 software s user guide for more details NOTE UDP port must be set the same both on the communicator using ELDES Configuration Tool and in EGR100 software 0o00 00 00 ki Eg L4 RING TIP C1 DC COM N A N A Z1 To external landline PSTN oo 0 RING TIP AUX AUX ALARM SYSTEM Fig No 25 internal landline PSTN 20 A FOR ADVANCED USERS ONLY A Connect the circuit as indicated in Fig No 25 connect telephone contacts of the alarm system RING TIP to RING TIP contacts of communicator 2 Connect L1 L2 contacts to external landline PSTN 3 Connect L3 L4 contacts to internal landline PSTN of PBX 4 Conn
28. rs the voltage dial tone monitoring optional on the PSTN and in case the PSTN is unavailable discon nected or cut off voltage drops below 4V the system e switches to backup connection GPRS network e notifies monitoring station about PSTN failure e continues transmitting data to monitoring station via GPRS network until the PSTN is restored NOTE Notification about PSTN loss restore if required has to be enabled for the communicator using ELDES Configuration Tool Please refer to software s HELP section for more details I The following communicator GPRS settings must be set up using ELDES Configuration Tool software CID over GPRS Enabled enables Contact ID data transmission via GPRS network e APN access point name provided by GSM operator e User Name user name provided by GSM operator e Password password provided by GSM operator e Server IP external IP address of the computer router running EGR100 software Server Port forwarded UDP port for the computer running EGR100 software Please refer to ELDES Configuration Tool software s HELP section for more details The following settings must be set up in EGR100 software e TCP UDP Server Port forwarded port for communication with the device via GPRS Please refer to EGR100 software s user guide for more details NOTE UDP port must be set the same both on the communicator using ELDES Configuration Tool and in EGR100 software
29. sensor connection The open collector output allows to connect and control 1 electronic appliance on receipt of the correct SMS text message from one of the preset phone numbers This feature provides control over heating lighting gates blinds etc ELDES Configuration Tool software is used to configure the system to operate in one of its communication modes providing data transmission either via SMS text message or via GPRS The device has to be connected to the computer using a USB cable Please refer to software s HELP section for more details 2 Technical Specifications 2 1 Electrical amp Mechanical Specifications Power Supply 10 24V 300mA max Current Used in Standby Mode 120mA max GSM Modem Frequency 850 900 1800 1900 MHz Supported Protocols Contact ID 4 2 Maximum Number of Users to whom SMS Messages are De 5 livered Number of Low Level Negative Digital Inputs 1 Allowable Input Values Voltage 0 1 45V current 0 8 0 6mA Input Type NO normally open Number of Outputs 1 Output Circuit Open collector output Output is pulled to COM when turned on Maximum Allowed Output Values Voltage 30V current 50 mA Dimensions 130x 73mm Operating temperature range 20 55 Generated Phone Line Voltage 18V Generated Phone Line Current 25mA Generated Phone Line Impedance 6000 Dial Tone Frequency of Generated Phone li
Download Pdf Manuals
Related Search