Kopiervorlage_Rahmendokument_Elektrogerät, 1, en_GB
Contents
1. tion After switching off the device wait for at least 15 minutes before you start any maintenance activities NOTICE Possible damages due to dirt or finger prints Due to the high temperatures even smallest pieces of dirt on the bulb can destroy the lamp when it is turned on Do not touch the lamp directly with your fingers Use clean gloves or a clean lint free tissue MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 51 Servicing NOTICE Possible damages due to wrong type of lamp Any attempt to use the device with a lamp other than those specified in this manual can result in severe damages to the device Only use a lamp of the specified type Information regarding the lamp This device is designed for a double ended metal halide lamp For correct replacement exam ples for manufacturer s types HMI 575W DXS HMQ 575 2 DE SFC10 4 have a look at www thomann de Follow the safety instructions of the lamp manufacturer themann moving head MUSIC IS OUR PASSION 52 Servicing MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 53 Servicing Ensure that the device is turned off disconnected from the power supply and that it has cooled down completely Instructions Move the head of the device into a horizontal position The arrow printed at the back of the head points to the upper side Loosen the four cross head screws at the upper side ofthe cover which are marked by A2. at the upper side of the cover which are marked by A in the figure above then remove the upper part of the cover Remove the snap ring of the gobo wheel then take out the gobo wheel C Do not loosen the screws located at the gobo wheel This way the ball bearings J would be opened u Stick the new gobo wheel on the axis Press the snap ring together and stick it on axis to fix the gobo wheel Attach the upper part ofthe cover to the device again and fix it by using the four associ ated cross head screws Connect the device to the power supply again MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 49 Servicing 8 2 Insert or exchange the lamp DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Completely disconnect the device from the power supply before you open or remove covers Mount all covers and attach them firmly before connecting the device again WARNING Eye damage caused by high light intensity The lamp used in this device produces an intense beam of visible and invisible light radiation Do not start the operation of the device without completely fixed covers Never look directly into the light source themann moving head MUSIC IS OUR PASSION 50 Servicing WARNING Risk of burns at the surface and inside of the device The surface and the inner parts of the device can become very hot during opera
3. in the figure above then remove the upper part of the cover Loosen the two knurled head screws of the lamp cover which are marked by B in the figure above Remove the lamp cover Carefully remove the old lamp Carefully insert the new lamp into the socket und check that is firmly secured Mount the lamp cover again Take care to snap the two retaining nugs of the lamp cover completely into the lamp housing Firmly tighten the two knurled head screws of the lamp cover again PE ELET EF E Attach the upper part of the cover to the device again and fix it by using the four associ ated cross head screws Connect the device to the power supply again 11 themann moving head MUSIC IS OUR PASSION 54 Servicing 8 3 Reset the lamp hours counter We recommend to reset the lamp hours counter after each exchange of the lamp That way you can easily check how long the lamp has been used amp Lamp hours counter on page 36 Instructions 1 Ensure that the device is turned off 2 Turn the device on and keep the DOWN key pressed as long as the display shows Resetting gt When the start up phase is finished the display shows Code 3 Using the keys UP and DOWN enter the value 88 4 Press the ENTER key gt The lamp hours counter has been reset to zero MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 55 Cleaning 9 Cleaning Optical lenses Clean th
4. mode on Yes or off No When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 33 Operation Pan inversion Tilt inversion Backlight themann MUSIC IS OUR PASSION Press MENU repeatedly until the display shows Pan Inversion Press ENTER The lower line of the display starts to flash Using UP and DOWN you can now select between Normal normal pan direction and Inverse inverse pan direction When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds Press MENU repeatedly until the display shows Tilt Inversion Press ENTER The lower line of the display starts to flash Using UP and DOWN you can now select between Normal normal tilt direction and Inverse inverse tilt direction When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds Press MENU repeatedly until the displ
5. must remain turned off Make sure that the power on off switch 18 is in the OFF position themann moving head MUSIC IS OUR PASSION 28 Operation Connect the device to the power supply To start the operation turn on the device using the power on off switch 18 After several seconds the fans start to work the head moves to the pan and tilt starting points the display shows that a reset is being performed Resetting After several additional seconds the display shows DMX Address The device is now opera tional 7 2 Main menu Press MENU to activate the main menu and to select a menu item When the display shows the desired menu item acknowledge the selection using ENTER The lower line of the display starts to flash Use UP and DOWN to change the value displayed When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds All previous settings are saved even if you switch off the device and disconnect it from the mains To start over with the default values use the RESET function MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 29 Operation DMX address themann MUSIC IS OUR PASSION Press MENU repeatedly until the display shows DMX Address Press ENTER The lower line of the display
6. press MENU MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 35 Operation Lamp hours counter Turn lamp on or off themann MUSIC IS OUR PASSION Press MENU repeatedly until the display shows Lamp Use Hour Press ENTER The lower line of the displays now shows the total number of lamp hours since the last reset To get back to the main menu press MENU To reset the value follow the instructions at amp Chapter 8 3 Reset the lamp hours counter on page 55 Use this function to manually turn the lamp on or off for example for maintenance activities Press MENU repeatedly until the display shows Lamp Press ENTER Using UP and DOWN you can now select between On Lamp on and Off Lamp off When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds moving head 36 Quick start Software version Reset Operation Use this function to specify the behaviour of the device when it is turned on Press MENU repeatedly until the display shows Lamp On Power On Press ENTER Using UP and DOWN you can now select between On lamp will be ignited immediately after the device is turned on and Off lamp remains dark immediately after the device is turned on When the displ
7. starts to flash Now you can adjust the number of the first DMX channel DMX address used by the device Select a value between 1 and 512 using UP and DOWN Make sure that this number corresponds with the configuration of your DMX controller When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds moving head 30 Operation Operating mode Auto Show Press MENU repeatedly until the display shows Show Mode Press ENTER The lower line of the display starts to flash Using UP and DOWN you can select one of the pre programmed shows Mode Meaning Show 1 Tilt movement angle 210 This mode is useful if the device is placed on the floor Show 2 Tilt movement angle 90 This mode is useful if the device is fixed under the ceiling or at a traverse MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 31 Operation Mode Meaning Show 3 The spot is always projecting to the audience s direction that means in front of the stage The pan movement angle left to right to left is 160 The tilt movement angle is 90 60 above horizon 30 below horizon This mode is useful when the device is placed on a speaker box Show 4 The spot is mainly projecting in front of the stage The pan movement angle
8. the standards and rules that apply in your country Always secure the device with a secondary safety attachment such as a safety cable or a safety chain MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 15 Installation themann MUSIC IS OUR PASSION gt gt CAUTION Risk of injury due to heavy weight Due to the heavy weight of the device at least two persons are required for trans port and installation CAUTION Risk of injury due to movements of the device The head of the device can move quickly pan tilt and can produce very bright light This is also valid immediately after you turn on the device when the device operates in automatic mode or under remote control and when you turn off a DMX controller that is connected to the device Persons staying near the device could be injured or frightened Before you turn on the device and during the operation always ensure that nobody stays close to the device If work has to be performed in the area of move ment or in the near vicinity of the device it must remain turned off moving head Installation NOTICE Risk of overheating The distance between the light output and the illuminated surface must be more than 0 5 m 19 7 in Ensure also that there is enough room for ventilation The ambient temperature must always be below 40 C 104 F NOTICE Possible damage caused by movements of the device Always ensure that enough space is free ar
9. with your normal household waste Dispose this device through an approved waste disposal firm or through your local waste facility When discarding the device comply with the rules and regulations that apply in your country If in doubt consult your local waste disposal facility MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 61 Notes themann moving head MUSIC IS OUR PASSION 62 Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany www thomann de
10. you start any maintenance activities CAUTION Risk of injury due to movements of the device The head of the device can move quickly pan tilt and can produce very bright light This is also valid immediately after you turn on the device when the device operates in automatic mode or under remote control and when you turn off a DMX controller that is connected to the device Persons staying near the device could be injured or frightened Before you turn on the device and during the operation always ensure that nobody stays close to the device If work has to be performed in the area of move ment or in the near vicinity of the device it must remain turned off MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 11 Safety notes NOTICE Risk of fire Do not block areas of ventilation Do not install the device near any direct heat source Keep the device away from naked flames NOTICE Operating conditions This device has been designed for indoor use only To prevent damage never expose the device to any liquid or moisture Avoid direct sunlight heavy dirt and strong vibrations themann moving head MUSIC IS OUR PASSION 12 Safety notes NOTICE Power supply Before connecting the device ensure that the input voltage AC outlet matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker Failure to do so could result in damage to the device and p
11. 0 255 Fine pan 14 0 255 Fine tilt 15 Special settings 0 130 Normal operation 131 139 Lamp on 140 200 Reserved 201 209 DMX reset 210 230 Reserved th mann moving head MUSIC IS OUR PASSION 44 Operation Channel Value Function 231 239 Lamp off 240 255 Reserved MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 45 Servicing 8 Servicing 8 1 Exchange the gobo wheel DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Completely disconnect the device from the power supply before you open or remove covers Mount all covers and attach them firmly before connecting the device again themann moving head MUSIC IS OUR PASSION 46 Servicing WARNING Risk of burns at the surface and inside of the device The surface and the inner parts of the device can become very hot during opera tion After switching off the device wait for at least 15 minutes before you start any maintenance activities MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 47 Servicing themann moving head Instructions LEE E ECE Servicing Ensure that the device is turned off disconnected from the power supply and that it has cooled down completely Move the head of the device into a horizontal position The arrow printed at the back of the head points to the upper side Loosen the four cross head screws
12. 13 25 Green 26 38 Magenta 39 50 Light blue 51 63 Yellow 64 76 Red 77 88 Blue 89 101 UV purple 102 114 Light green 115 127 Pink 128 191 Rotation clockwise speed decreasing MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 41 Operation Channel Value Function 192 255 Rotation counterclockwise speed increasing 7 Gobo wheel 0 15 White no gobo 16 31 Gobo 1 32 47 Gobo 2 48 63 Gobo 3 64 79 Gobo 4 80 95 Gobo 5 96 111 Gobo 6 112 127 Gobo 7 128 191 Rotation clockwise speed decreasing 192 255 Rotation counterclockwise speed increasing 8 Rotation of the gobo wheel th mann moving head MUSIC IS OUR PASSION 42 Channel 10 Value 0 127 128 191 192 255 Prism 0 85 86 170 171 255 Operation Function Index position 0 to 360 Rotation clockwise speed decreasing Rotation counterclockwise speed increasing White no prims Prism effect 1 Prism effect 2 Prism rotation for prism effect 1 and 2 0 9 10 120 121 134 135 245 245 255 No rotation Rotation clockwise speed decreasing No rotation Rotation counterclockwise speed increasing No rotation MH 575 S MKII Pro Spot th mann MUSIC IS OUR PASSION 43 Operation Channel Value Function 11 Focus 12 Iris zoom maximum to minimum aperture 0 10 Maximum aperture 10 26 Zoom from 0 to 100 27 255 Iris maximum to minimum aperture 13
13. Cleaning 252442 56 Troubleshooting u ccccssscsssscssssssssssseesssecsscecsnecessecssseessecesseesssccsssccesessuecesseessscessescsscesssceescessnecesseeess 57 Technical d ta u u Kreide 59 Protecting the environment unsneeenseeensseennseennnsennnnsennnnssennnssenssennnnssennnsnennntnennne 61 moving head 1 General notes Symbols and signal words General notes This user manual contains important information on the safe operation of the device Read and follow all safety notes and all instructions Save this manual for future reference Make sure that it is available to all persons using this device If you sell the device to another user be sure that they also receive this manual Our products are subject to a process of continuous development We therefore reserve the right to make changes without notice This section gives an overview of the symbols and signal words used in this user manual MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION General notes Signal word DANGER WARNING CAUTION NOTICE themann moving head MUSIC IS OUR PASSION Meaning This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a possible dangerous situation that can result in death or serious injury if it is not avoided This comb
14. MX interface circuits If the procedures recommended above do not succeed please contact our Service Center You can find the contact information at www thomann de themann moving head MUSIC IS OUR PASSION 58 Technical data 11 Technical data Number of DMX channels 15 Lamp Double ended metal halide lamp 90 V 575 W for example HMI 575W DXS HMO 575 2 DE SFC10 4 Beam angle 14 or 18 zoom lenses controllable via DMX Maxim pan angle 540 Maximum tilt angle 270 Iris 0 100 Dimmer 0 100 Shutter 0 10 Hz Mains power supply 220 240 V AC 50 60 Hz Power consumption 700 W Fuse 10 A slow operation MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 59 Technical data Dimensions W x D x H 432 mm x 369 mm x 535 mm Weight 29 5 kg themann moving head MUSIC IS OUR PASSION 60 Protecting the environment 12 Protecting the environment Disposal of the packaging mate rial For the transport and protective packaging environmentally friendly materials have been chosen that can be supplied to normal recycling 4 Ensure that plastic bags packaging etc are properly disposed of Do not just dispose these materials with your normal household waste but make sure that they are fed to a recovery Please follow the notes and markings on the packaging Disposal of your old device This device is subject to the European directive 2002 96 EC Do not dispose the device
15. Ss trier we MH 575 S MKII Pro Spot moving head th mann user manual MUSIC IS OUR PASSION Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany Telephone 49 0 9546 9223 0 email info thomann de Internet www thomann de 07 02 2012 Table of contents na vu RA WN Table of contents Generalnotes unaulksnkdnekessaaseakedunenieeebdnnnlidnsdasit 5 Safety notes Features Installationu hs umesnasssunsetnsdtaannknnladneeesinnmravatuinesanertlain Setup 21 Components and functions isueseenerssrsseesssessiesseeseeesseeeseersseersssessseresseessesesseeessevssseersser 24 Operation niunssmningjvyuennmspandksensiinengetstrtvtrteketvdevvrputieptereieneneruetent 28 7 1 Start the device rrenuserserssesnserssserssseesseresseeeserrsseresserssserssseesseresssesseseesesesseerssrssssssssereeee 28 72 73 74 7 5 Servici g sonnan a iaaa AA aian i a 46 8 1 Exchange the gobo wheel esrrssserssssersssserssssrsassereussereussereusserenssereussereussereusseresssesesssrsesssesesseren 46 8 2 Insert or exchange the lamp errsserrrssserssssersssrssssersssserssssersssserssssersssserssssesssseeessssenssssensssersnsser 50 MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION Table of contents themann MUSIC IS OUR PASSION 10 11 12 8 3 Reset the lamp hours COUNTEM ecssssssssssesseessesssesssesssessesssessncssscssscesesssesssesssssnecssessseesscenscsneesees 55
16. ay shows Backlight Press ENTER The lower line of the display starts to flash Using UP and DOWN you can now select between On backlight LED on and Off backlight LED off When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds moving head 34 Focus adjustment Self test Lamp temperature Operation Press MENU repeatedly until the display shows Adjust Focus Press ENTER The lower line of the display starts to flash Use UP and DOWN to select a value between 0 and 255 To make the adjustment easier the beam will be automatically directed straight upwards or if the device is mounted at the ceiling downwards When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds Press MENU repeatedly until the display shows Test Press ENTER The device now starts a self test the display shows Testing To stop the self test and to get back to the main menu press MENU Press MENU repeatedly until the display shows Lamp Temperature The lower line of the dis play now shows the lamp temperature To get back to the main menu
17. ay shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds Press MENU repeatedly until the display shows Version Press ENTER The lower line of the displays now shows the software version of the device To get back to the main menu press MENU Press MENU repeatedly until the display shows Reset Press ENTER The lower line of the display now shows that a reset takes place Resetting the device will be reset to its default settings MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 37 Operation 7 3 Menu diagram themann moving head MUSIC IS OUR PASSION 38 Operation 7 4 Gobos The following figure shows the available gobos and their numbers MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 39 Operation 7 5 Functions in 15 channel DMX mode Channel Value Function 1 0 255 Pan 0 to 540 2 0 255 Tilt 0 to 270 3 0 255 Pan and tilt speed fast to slow 4 0 255 Dimmer 0 to 100 5 Shutter shake 0 7 Blackout 8 15 Open 16 131 Shutter speed increasing 132 185 Open 186 239 Shake speed increasing 240 247 Shutter random speed themann moving head MUSIC IS OUR PASSION 40 Operation Channel Value Function 248 255 Open 6 Colour wheel 0 12 White
18. e exterior of accessible optical lenses periodically to optimise light output The fre quency of cleaning depends on the operating environment wet smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device Clean with a soft cloth using normal glass cleaning products Always dry the parts carefully themann moving head MUSIC IS OUR PASSION 56 Troubleshooting 10 Troubleshooting NOTICE Possible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX output to audio devices such as mixers or amplifiers Following we list a few common problems that may occur during operation We give you some suggestions for easy troubleshooting MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 57 Troubleshooting Problem Corrective action The device does not work no Check the power connection and main fuse light the fans do not run No response to DMX controller 1 The DMX LED should be on If that is not the case check wether the DMX connections are correct and cables are in a proper condition 2 If the DMX LED is on but you can see no reaction check the address settings and the DMX polarity 3 Try to use another DMX controller 4 Check to see if the DMX cables run near or alongside to high voltage cables that may cause damage or inter ference to D
19. es that a sound signal is being received by the microphone 5 Display 6 MENU Activates the main menu 7 UP Increases the value displayed by one MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 25 Components and functions 8 DOWN Decreases the value displayed by one 9 ENTER Chooses an option of the current operation mode 10 Carrying handle 11 Fan 12 SENSITIVITY Control knob to adjust the sensitivity of the microphone in the sound mode 13 MIC Microphone used for the sound mode 14 DMX OUTPUT DMX output 15 DMXINPUT DMX input themann moving head MUSIC IS OUR PASSION 26 Components and functions 16 Power cord 17 Fuse holder 18 Power on off switch Switches the device on and off MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 27 Operation 7 Operation 7 1 Startthe device CAUTION Risk of injury due to movements of the device The head of the device can move quickly pan tilt and can produce very bright light This is also valid immediately after you turn on the device when the device operates in automatic mode or under remote control and when you turn off a DMX controller that is connected to the device Persons staying near the device could be injured or frightened Before you turn on the device and during the operation always ensure that nobody stays close to the device If work has to be performed in the area of move ment or in the near vicinity of the device it
20. ination of symbol and signal word indicates a possible dangerous situation that can result in minor injury if it is not avoided This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided General notes Warning signs Type of danger Warning high voltage Warning hot surface Warning dangerous optical radiation Warning suspended load Warning danger zone gt e eee MH 575 S MKII Pro Spot th mann MUSIC IS OUR PASSION Safety notes 2 Safety notes Intended use This device is intended to be used as moving head spotlight Use the device only as described in this user manual Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage No liability will be assumed for damages resulting from improper use This device may be used only by persons with sufficient physical sensorial and intellectual abilities and having corresponding knowledge and experience Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety DANGER Danger for children Ensure that plastic bags packaging etc are disposed of properly and are not within reach of babies and young children Choking hazard Safety Ensure that children do not detach any small parts e g knobs or the like from
21. left to right to left is160 The tilt movement angle is 90 vertically front 75 back 15 This mode is useful if the device is fixed under the ceiling or at a traverse When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds The automatic show selected starts if no working DMX controller is connected themann moving head MUSIC IS OUR PASSION 32 Operating mode Master Slave Operating mode Standby Operation Press MENU repeatedly until the display shows Slave Mode Press ENTER The lower line of the display starts to flash Using UP and DOWN you can now select between Slave 1 the movements of master and slave device are identical and Slave 2 the movements of master and slave device are different When the display shows the desired value press ENTER After that keep MENU pressed for several seconds to acknowledge the value To get back to the main menu without changes either press MENU briefly or wait for eight seconds Use this function to turn off the light temporarily without the need to change the other set tings Press MENU repeatedly until the display shows StandBy Mode Press ENTER The lower line of the display starts to flash Using UP and DOWN you can turn the Standby
22. ossibly injure the user Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 13 Features 3 Features themann MUSIC IS OUR PASSION The moving head is very suitable for professional lighting for example at events on rock music stages in theatres musical shows or clubs Special features of the device M Control via DMX 15 channels foot master pocket master or via keys and display at the device Built in automatic show programs Sound active mode Master slave mode Colour wheel with 9 dichroitic colour filters plus white Rainbow effect in both directions Gobo wheel with 7 indexable and rotatable gobos variable rotation speed and direction Effect wheel with rotatable 3 facet prim variable rotation speed and direction Automatic position correction moving head 14 Installation 4 Installation Unpack and check carefully there is no transportation damage before using the unit Keep the equipment packaging To fully protect the device against vibration dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage respectively You can install the device on the wall ceiling or floor WARNING Risk of injury caused by falling objects Make sure that the installation complies with
23. ound the device for the movements of the head pan tilt MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 17 Installation NOTICE Possible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX output to audio devices such as mixers or amplifiers themann moving head MUSIC IS OUR PASSION 18 Installation Options for mounting MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 19 Installation 1 Mounting hole for omega brackets 2 Screw thread for clamps 3 Hole for safety cable The mounting holes and screw threads at the housing underside can be used for secure fixing of clamps with or without omega brackets Safety cables can be lead through the holes at the underside DMX connections The unit offers a 3 pin XLR socket for DMX output and a 3 pin XLR plug for DMX input Please refer to the drawing and table below for pin assignment 1 Ground shielding 2 DMX data 3 DMX data themann moving head MUSIC IS OUR PASSION 20 Setup 5 Setup Establish all connections as long as the unit is switched off Use the shortest possible high quality cables for all connections MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 21 Setup Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device Connect the
24. output of the first DMX device to the input of the second one and so on to form a daisy chain Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor 110 Q W Twn ww DMA Out OMX in OMX Gut DX In DR M Cut 2 themann moving head MUSIC IS OUR PASSION 22 Setup DMX Indicator When the device and the DMX controller are operating the LED DMX indicates that a DMX signal is being received at the input Connections in master slave When you configure a group of devices in master slave mode the first unit will control the mode other units for an automatic sound activated synchronized show This function is ideal when you want to start a show immediately Connect the DMX output of the master device to the DMX input of the first slave device Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION 23 Components and functions 6 Components and functions themann moving head MUSIC IS OUR PASSION 24 Components and functions 1 DMX The LED indicates that a DMX signal is being received 2 MASTER The LED indicates that the device is used as master It controls the slaves connected to it 3 SLAVE The LED indicates that the device is a slave under control of a master 4 SOUND In the sound mode the LED indicat
25. the unit They could swallow the pieces and choke Never let children unattended use electrical devices themann moving head MUSIC IS OUR PASSION Safety notes DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Completely disconnect the device from the power supply before you open or remove covers Mount all covers and attach them firmly before connecting the device again DANGER Electric shock caused by short circuit Do not modify the mains cable or the plug Failure to do so could result in electric shock death or fire If in doubt seek advice from a registered electrician MH 575 S MKII Pro Spot themann MUSIC IS OUR PASSION Safety notes WARNING Eye damage caused by high light intensity The lamp used in this device produces an intense beam of visible and invisible light radiation Do not start the operation of the device without completely fixed covers Never look directly into the light source WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy Sensitive persons should avoid looking at strobe lights themann moving head MUSIC IS OUR PASSION Safety notes WARNING Risk of burns at the surface and inside of the device The surface and the inner parts of the device can become very hot during opera tion After switching off the device wait for at least 15 minutes before
Download Pdf Manuals
Related Search