LED SPIDER MOVING HEAD LIGHT
Contents
1. CH12 Macro 0 10 No function 11 29 Light ON 30 49 Light Strobe 50 249 macro function 250 255 sound control DMX address is more than 10 each add 20 will be a macro function CH13 Macro speed 0 255 from fast to slowly CH14 Sound and Automatic 0 64 No function control 65 128 Auto model 129 192 Sound model 193 255 Rest Each functional delay for 10 seconds 20Channel model Channel Function Value CH1 Pan 0 255 CH2 Tilt 1 0 255 CH3 Tilt 2 0 255 CH4 Pan fine Main dimming 0 255 CH5 Tilt 1 Fine 0 255 CH6 Tilt 2 Fine 0 255 CH7 Motor speed 0 255 CH8 Main dimming 0 255 CH9 Strobe 0 255 CH10 L1 Dimming 0 255 CH11 L2 Dimming 0 255 CH12 L3 Dimming 0 255 CH13 L4 Dimming 0 255 CH14 L5Dimming 0 255 CH15 L6Dimming 0 255 CH16 L7 Dimming 0 255 CH17 L8 Dimming 0 255 CH18 Macro 0 10 No function 11 29 Light ON 30 49 Light Strobe 50 249 macro function 250 255 sound control DMX address is more than 10 each add 20 will be a macro function CH19 Macro speed 0 255 from fast to slowly CH20 Sound and Automatic 0 64 No function control 65 128 Auto model 129 192 Sound model 193 255 Rest Each functional delay for 10 seconds www mjledlighting com mess 12O Ushio Spider Moving Head Light MJ 1031 White User Manual ver2 0 Technical Parameters Voltage AC90V 240V 50 60Hz Power Consumption 120W 220V LED Bu2. 4 5 N 5 www mjledlighting com mage TEO Utis Spider Moving Head Light MJ 1031 White User Manual ver2 0 Connection between the controller and a projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin which are included with the projector XLR plugs and sockets The XLR s are connected as shown in the figure above Note Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The XLED 590 accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below DMX Terminator In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120
3. Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the optical system clean Do not touch the LED lens with bare hands The product should always be installed with a secondary safety fixing On the projector base brink there is a hole for the safety cord provided It should be attached as shown in installing the projector section LED lens shall be changed if they have become visibly damaged to such an extent that their ON effectiveness is impaired for example by cracks or deep scratches S lt 42 SPA Y Exterior surface temperatures of the luminaire after 5 minutes operation is 40 C when steady state is achieved 50 C There is no user serviceable parts inside the projector do not open the housing and never operate the product with the covers removed If you have any questions don t hesitate to consult your dealer or manufacturer Always disconnect from the mains when the device is not in use or before cleaning it or before
4. OHM resistor i across pins 2 and 3 in an XLR plug Bel and insert it into the DMX out socket y en C1200 any am on the last unit in the chain PIN 2 PIN3 5 PIN XLR 3 PIN XLR Function Set Menu down up Enter Use button switch and LED display can set the address code and function code easily Check or modify lighting function settings Press the MENU button LED display panel will display function menu of lighting Function operation menu all have corresponding submenu Each menu all represent the specific functions of lamps specific see below operation menu section Set or browse function setting of lamp Press UP or DOWN button Press ENTER button to save your changes or to ENTER submenu Press UP or DOWN can change value Plus or reduce number According to the ENTER key to return to the last menu www mjledlighting com Nn sepa eDUohtng Spider Moving Head Light MJ 1031 White User Manual ver2 0 Menu Function Description No Display Function DMX MODE 1 CH14 14 20 channel choose 2 Ds DMX address 0 255 001 ADJ R 3 gt 5 Adjust the brightness 0 255 7 PROCE AM Inner program 001 prog PEED 8 gt 16 Inner program speed 1 16 9 TEST MODE Sound and Automatic control model choose 10 RESET Rest Maintenance To prolong the life of the proiector some maintenance work has to be done to ensure the LED optical system in good condition If the projector does n
5. LED SPIDER MOVING HEAD LIGHT MJ 1031 White INSTRUCTION MANUAL Thank you for choosing our LED spider moving head light For the sake of your safety Please read and follow these instructions carefully and keep this manual in a safe place for future reference mage eo Uahing Spider Moving Head Light MJ 1031 White User Manual ver2 0 Catalogue Chapter Page Safe Usage Of The Product 3 Install The Equipment 92 noon nnn nnn 4 Power Code Connection 4 DMX Connection n ono nnn nnn nn nnn nnn nnn nnn nnn nnn nnn nn cnn nnn nnn nnn 5 DMX Terminator rn nnn nnn nn nnn 5 Function Set nnn nnn nn nnn nnn nnn ncn 5 Menu Function Description 6 Maintenance 2 nnn nn enna nnn nn nnn nnn nnn nnn 6 Keeping The Product Clean 6 Trouble Shootin
6. attempting any maintenance work www mjledlighting com U 6 mage TEO Ughing Spider Moving Head Light MJ 1031 White User Manual ver2 0 Install The Equipment Use lpcs clamp need to purchase Use clamp fix with light hook which in the packing box with light then use screw install to the bottom of lamp Hang the fixture on the structure and fasten the screws attached to each clamp Make sure the light is installed reliable and confirm the light which you fixed is strong enough for hanging the light Base on safety reason please according to the above picture using safety wire cross the light to make it strong enough again Warning 1 Hook and clamp only use for hanging the light Do not use clamp as a tool to move fixtures 2 Don t use the handle of the moving head light to fixed or lift Power Code Connection Connect the power cord as follows L live brown E earth yellow green N neutral blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards DMX Connection DMX OUT DMX IN DMX 512 DMX OUT DMX IN o9 Co MX 5 FUNCTION 1 GND sPIN fo o s ATA o y f 2 o
7. ement changes the related specification the authority This instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy also cannot the related consequence which causes regarding these information be responsible www mjledlighting com mage eo Uahing Spider Moving Head Light MJ 1031 White User Manual ver2 0 SAFE USAGE OF THE PRODUCT When unpacking and before disposing of the carton check there is no transportation damage before using the product Should there be any damage caused by transportation consult your dealer and do not use the apparatus The product is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The product is not designed or intended to be mounted directly on to inflammable surfaces The product is only intended for installation operation and maintenance by professional person The product must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not product the beam onto inflammable surfaces minimum distance is 5m 5m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle or modify the projector in any way Electrical connection must only be carried out by qualified personnel
8. g 99 n nn nnn anon nnn nn nnn nnn nnn nnn 6 Equipment and Appendix 7 Channel List 7 27 20 22 nena nn nn nnn nnn nnn 7 Technical Parameters 9 xImportant notice e In this instruction for use contains about the installment and the use aspect important information of the LED moving head When installing and using you need to look this usage instruction strictly Before open the LED moving head and if you want to do the repair work please make sure the power source is at the separation condition e Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer or dealer Attention Unceasingly carries on the product improvement about our company the policy in this instruction booklet carries the data will have the possibility to be able to change in the future when no longer separate notice change matters concerned Our company retains when the product improv
9. ht MJ 1031 White User Manual ver2 0 Although shines but the LED moving head lamp doesn t accept the instruction of the controller Check the digital start address and also check the connection situation of the communication control line LED moving head lamp only can work intermittently Inspect the power supply and voltage is whether normal Do not receive the DMX512 signal Whether the signal lines do contact well or broken The light beam appears gloomily Check that the heat dissipation system is running normally or Inspect the optics part is whether clean yx Other maintain work should by the specialist which has the experience to carry on Equipment and Appendix The packing list of this light as follows yx Led moving head light Ipcs yx Power Cable pcs yx XLR connector lunit yx Light Hook Ipcs xXx The Product of Instruction Ipcs Channel List 14Channel model Channel Function Value CH1 Pan 0 255 CH2 Tilt 1 0 255 CH3 Tilt 2 0 255 CH4 Pan fine Main dimming 0 255 CH5 Tilt 1 Fine 0 255 CH6 Tilt 2 Fine 0 255 CH7 Motor speed 0 255 CH8 Main dimming 0 255 CH9 Strobe 0 255 CH10 Dimming CH11 The LED bulb control 0 9 All ON 10 39 L1 ON 40 69 L2 ON 70 99 L3 ON 100 129 L4 ON 130 159 L5 ON 160 189 L6 ON 290 219 L7 ON 220 250 L8 ON www mjledlighting com Spider Moving Head Light MJ 1031 White User Manual ver2 0
10. lbs 10W 8LEDs Lumen White LED LED Current 1800mA LED Lifetime 50000Hours Adjusts the light 0 100 electron adjusts the light Strobe 1 25 second high speed strobe Pan Movement 540 Tilt Movement 180 Beam Angle 6 Control mode DMX 512 Stand alone mode Self test mode Sound Master slave DMX Channel 14 20CH Control Panel LED display panel IP Grade IP33 Work Environment Temperature 20 C 40 C Net weight 7 5KG Gross Weight 8 8 kg Package Size 46 x 32x 29cm www mjledlighting com 9
11. ot function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification Should these be damaged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating Should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not call a qualified technician yx Any maintenance work should only be carried out by qualified technicians Keeping The Product Clean To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days LED lens should also be regularly cleaned to maintain an optimum light output Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean the external optics at least once every 15 days yxDo not use any organic solvent e g alcohol to clean housing of the apparatus Trouble Shooting Problem Answer The LED moving head light doesn t switch Check the fuse the power socket on www mjledlighting com 6 ls sage To Ughing Spider Moving Head Lig
Download Pdf Manuals
Related Search