User Manual - Elan Medical Supplies
Contents
1. z uabrRAsyuged gy PH awo ueuny W c Intertek 4002134 Wireless transmission equipment mobile telephones etc must not be used close to the device as it may affect its function Particular caution must be observed when using strong sources of interference such as diathermy and such like to ensure that no diathermy cables are placed on or near the device If in doubt ask the person in charge of the equipment or the supplier Symbols on the unit C CE marking Date of manufacture Manufacturer Max lifting capacity Instructions Read the instructions and make sure you understand them before using this product Item number reference number Serial number Warning The lift contains lead batteries and electronics and it must be recycled appropriately SBR DEL Type B product cS Switch off the product Switch the product on fe 3 LAN Ale Go Third party certification marking not applicable for all regions and versions Functions Emergency stop In an emergency the emergency stop can be activated by pressing the RED button 15 To reset the emergency stop turn the RED button clockwise Emergency lowering In case of an emergency situation the emergency lowering button 13 can be pressed An audio signal indicates that the lift is lowering Always ensure that emergency lowering can be performed as safely as possible for the patient The emergency lowering button only works w2. 1 8 m min 3 0 m min unloaded only Battery charger Input 100 240V AC 50 60 Hz 6 A Output 27 8V 0 8A DC Battery charger IP class IPX0O ETL Yes This product is designed for repeated use The telescopic bar is adjustable to three different widths 35 45 and 55 cm 13 8 17 2 21 7 in Technical specification Singel 4100 Lifting capacity max 150 kg 330 Ibs 23 6 st Start stop soft Dimensions 450x180x340 mm Weight of lift 10 kg 22 Ibs 1 6 st WxHxL 17 7x7 1x13 4 in Batteries 2x12V 3 2Ah Emergency lowering electronic manual Indicator Type and class B Standby flashing GREEN Class Internally powered Active constant GREEN equipment Charge batteries flashing RED Lift IP class IPX4 Error constant RED Remote control Class IP65 Lifting height 680 mm Noise level 50 dBA unloaded 65 dBA loaded Lifting speed 1 8 m min 3 0 m min unloaded only Battery charger Input 100 240V AC 50 60 Hz 1 6 A Output 27 8V 0 8BA DC Battery charger IP class IPX0O ETL Yes This product is designed for repeated use The telescopic bar is adjustable to three different widths 35 45 and 55 cm 13 8 17 2 21 7 in Product description Singel 5100 Singel 4100 overhead lift Charger Remote control UP button remote control DOWN button remote control Lift belt Leg hook Telescopic bar Hanger bar hook 10 Switch with protective cover I 1 UP button on lift 12 DOWN button on lift 3 Emergency lowering button 14 I
3. THE CAREGIVER If the Singel 5 100 Singel 4100 is used in any way that is not recommended by Human Care then Human Care will not accept responsibility for any injuries or accidents that may occur Always contact your supplier if you have any questions or if anything is unclear Human Care s products are continuously being developed and updated and we reserve the right to make design changes without prior notice Contents Sae MUCO aerea a EE AE EEE EEE EENES 2 Technical specification Singel 5100 cece eee eee eee eee eee eee e ee eee rr rr nr rr RK eens sa R KRK n Rn 3 Technical specification Singel 4100 sssssssssrssssrssrsrsssrsrnsrnrnsrnenrrn enn rn rnr rn renen rr rn R KAR RR KKR RR Kran 3 PrOGUCE descripto sestsssorssndeboserni keseredenbsekeiokese n aR An E ar REN ANRE EEEREN kad 4 Mondod Uee E E 5 Frode VA iee E E EE 5 NDO ON CIS UN osese tainp ein eE EEEE SEEE SEE EEE EO EE 5 BANG EN OMS e cig be ate sects ea eee cate ea eg gc ee see a eg ge se ae ea eee ec ee 6 RIVA SI sate ates cette scot te atte cette gnats ete cet etme tree gets ect eeteateedate eiteratet eae 8 DOW TENSION SUA sic ccpeae E E E E E E E E 9 Gone CHV IDE ease A S E E feccecrer 9 Telescopic DAN ie ea S E ED E EEG 10 ES TAIN CLOT rese een apenas emia nts ouiers eens emseerenewetene mew enemn ses eeninecpseweaees 11 TEU ISS NOD INS eeren a E uses E NS SNS rss 12 Care instructions for the lift and aCCESSOrieS ssssserssrersrrsrerrnrnrrnrnrrn rr ren rr
4. should meet the user s various requirements and needs See www humancare se for further information about which models and sizes offered 50348 Scales Patient scales that can be used in conjunction with any of the Human Care lifts Max weight 320 kg 20124 Distance strap Several different lengths are available in order to adjust the lift height to a suitable level 50268 Four point suspension bar Can be used in conjunction with any of the Human Care lifts 50700 Stretcher This most portable lightweight stretcher with a lifting capacity of 200 kg The stretcher can be assembled by one I person without any tools 50600 Portabla Niklas freestand The freestand is adjustable in both height and width The height can be adjusted up to 2 450 mm without using any tools This makes the Niklas freestand the most portable solution on the market The freestand is intended for use for lifting users from e g a bed to a wheelchair The Niklas portable freestand can be assembled by one 1 person without using any tools Max capacity is 220 kg 50346 Cart Portability of the lift can be further enhanced with our new cart The cart is specially produced for our Roomer 5200 and Singel 5100 lifts but it can also be used with earlier Human Care lifts e rsta ngsv gen 21C SE 117 43 Stockholm Sweden e Tel 46 0 8 510 132 00 Fax 46 0 8 665 35 10 e www humancaregroup com 99567 ENG Rev B 2013 04 11
5. USER MANUAL Overhead lift SINGEL 5100 NA HUMAN CARE Prod No 5000I NA Your Life Your Way Overhead lift SINGEL 4100 NA Prod No 41000 NA The Singel 5100 and SINGEL 4100 provide you with a unique ability to move a patient safely and easily as a result of which both the patient and the caregiver avoid exposure to unnecessary strain during lifting and moving operations The lift is used for lifting and moving a patient for example to or from a bed wheelchair or shower bath or from the floor The apparatus can also be used for walking training balance training and weighing N WARNING This symbol is sued when particular attention is required IMPORTANT Lifting and moving a person always entails some risk You should therefore carefully read through the instructions for both the lift and lift accessories Always make certain that the accessories you are using work with the lift As a caregiver you are responsible for the safety of the patient and you must be familiar with their ability to cope with the lifting situation Human Cares lifts are designed only to raise and lower patients in a vertical direction and never diagonally or through angles The lift must always be positioned directly above the patient when lifting The patient must always be located above the surface onto which he or she is to be lowered LIFTING OR LOWERING A PATIENT DIAGONALLY OR IN AN ANGLED MOVEMENT MAY RESULT IN INJURY TO THE PATIENT OR
6. ccessories e the correct types sizes materials and designs of the accessories have been selected with respect to the patient s safety and needs e the lift accessories have been correctly installed The sling s strap loops must be checked once the loops are fully extended when lifting but before the patient is lifted from the underlying surface Human Care provides suitable training in safe operation of the lift and other accessories Further information about slings rail systems and other accessories can be found on www humancare se Important To ensure that the lift belt will not be damaged it is important that Ithe lift is balanced during moving lifting and lowering operations Never hold or pull the lift belt when moving a patient It is also important that the lift belt is tensioned it is wound in N Warning Modification of the product is not permitted without the manufacturer s consent Lr nn 2 Technical specification Singel 5100 Lifting capacity max 220 kg 484 lbs 34 6 st Start stop soft Dimensions 450x180x340 mm Weight of lift 10 kg 22 Ibs 1 6 st WxHxL 17 7x7 1x13 4 in Batteries 2x12V 3 2Ah Emergency lowering electronic manual Indicator Type and class B Standby flashing GREEN Class Internally powered Active constant GREEN equipment Charge batteries flashing RED Lift IP class IPX4 Error constant RED Remote control Class IP65 Lifting height 680 mm Noise level 50 dBA unloaded 65 dBA loaded Lifting speed
7. he necessary length of the lift belt in order to be able to hook it onto the rail hook or to unhook it Using the lift Press the UP button 4 10 to lift the patient and the DOWN button 5 IT to lower the patient Pressing the button activates a soft start and releasing it causes a soft stop Telescopic bar Set the telescopic bar 8 to the prescribed position Ensure that the hooks 9 are in the same position on both sides Place the patient in the selected sling according to the sling instructions and hang the sling in the hooks 9 on the telescopic bar and in the leg hook 7 Check that the sling is properly anchored in the hooks 9 7 The hanger bar hooks 9 have three adjustable positions To change position turn the hooks 1 4 turn while pushing or pulling the hooks to the desired position The hooks will automatically fall into place in the position and so it is necessary to repeat the turn 1 4 turn when passing the middle position position 2 See fig B Definitions A is the total height of the system B The distance from the ceiling down to the bottom of the lift hanger A 380 460 mm depending on rail solution A is the lifting height The difference between the lift s highest and lowest positions i e belt length Different lengths of distance straps for lengthening the lift belt are available as accessories B 1 680 mm Lift cycle B Lift action consisting of a lift of 420m
8. hen the mains switch 10 is switched on and emergency stop has been de activated NB The emergency lowering button must only be used in emergency situations If the mains switch 10 is turned to OFF and there is a person in the sling the lift will sink safely and slowly manual emergency lowering Safety catch The lift is equipped with a safety catch This prevents involuntary falls If the lift belt is pulled out too quickly the safety catch will engage thus preventing the fall Slacken the lift belt to unlock the catch A N Overheating protection The lift has overheating protection which stops the motor if it gets too hot Overheating can occur if the motor is overloaded or operated continuously for quite a long time The lift s work cycle work pause is 15 85 Maximum continuous operation is 6 minutes If this is exceeded there is a risk of the motor overheating Suspending the lift from the rail Place the lift on a suitable surface Turn on the mains switch press the DOWN button 5 I 1 and pull out a suitable length of belt and hook it onto the distance strap diagonally from above see fig A The lift is now ready for use Remote control functions The remote control 3 has an UP button 4 and a DOWN button 5 When the lift is loaded with less than approx 40 kg it can be run in two speeds Pressing the buttons lightly makes the lift run at slow speed while pressing hard makes it run at high speed The fo
9. in Activate by turning the red button clockwise The batteries need to be charged but it is still possible to use the lift to lift the patient a few times though the lift 1 should be charged as soon as possible N Care instructions for the lift and accessories Care instructions for the lift e The lift should be recharged every night e Dry the overhead lift using a slightly dampened drying cloth Dishwashing liquid can be used Never wash the overhead lift using water or any other fluids NEVER use strong detergents on the lift unit If the lift is to be disinfected DuPont Virkon can be used The mains switch 10 should always be OFF during transport Turn the mains switch 10 off or activate the emergency stop if the overhead lift is not going to be used for a few days Otherwise the batteries will run down Annual inspection The lift must be inspected at least once a year by personnel authorised by Human Care Pay particular attention to parts that show wear Installation service and maintenance must be performed by personnel authorised by Human Care and using original spare parts Daily inspection e Always check the sling before use There must be no loose seams or other signs of wear to lift belts belts and fabric If there are replace the sling e Check the overhead lift for visible signs of damage Monthly inspection e Check the lift belt 6 for damage or wear and tear Feed out enough of the lift belt to allow
10. its entire length to be checked Contact a retailer if the belt is damaged Service agreements Human Care invites you to sign a service agreement for annual inspection and test loading Transport and storage During transport or when the lift is not going to be used for some time the main switch must be off or the emergency stop button pushed in otherwise the batteries will discharge The climatic conditions should be as follows ambient temperature from 0 C to 50 C relative ambient humidity from 30 to 80 and ambient pressure from 790 hPa to 1 060 hPa Expected lifetime The lift is expected to function for 10 000 lifting cycles at maximum lifting capacity or for 10 years with correct service and maintenance Recycling Work out overhead lifts can be returned to Human Care for recycling NB Contains batteries and electronics that contain lead and which must be recycled afterwards WEEE 2002 96 EC For additional information about accessories and technical documentation please visit our website at www humancare se Slings and accessories If the maximum weight for any of the accessories e g slings lift bars and any other accessories is NOT the same as for the lift then the lowest max weight given for any one product is the one that shall apply Always check the label on the lift and lifting accessories or contact Humane Care if you have any questions or if anything is unclear Slings Human Care s range of slings is wide and
11. m and lowering by 420mm Troubleshooting Indicator lamp 14 Nothing happens when the UP buttons 4 or II or DOWN buttons 5 or 12 are pressed Nothing happens when the UP button 4 or the DOWN button 5 is pressed on the remote control 3 Nothing happens when the UP buttons 4 I 1 or DOWN buttons 5 12 are pressed Nothing happens when the UP buttons 4 I I are pressed Nothing happens when the UP buttons 5 12 are pressed Nothing happens when the UP buttons 4 I I or DOWN buttons 5 12 are pressed The indicator lamp 13 turns from green to flashing red Not lit Flashing green Flashing red Constant red Flashing green Flashing red Flashing green Flashing red Flashing green Flashing red Flashing red Check that the mains switch 10 is ON 2 The batteries are fully discharged Charge the lift 1 immediately 3 The emergency stop 11 is pushed in Activate by turning the red button clockwise Check that the remote control 3 is connected to the lift 1 Charging in progress Interrupt charging 2 Lift motor is overheated Wait a while a try again 3 The lift 1 is overloaded Lower the lift using the emergency lowering button 15 The lift is in its maximum upper position Press the DOWN button 5 12 to lower it The lift is in its maximum lower position Press the UP button 4 1 to raise it The emergency stop 15 is pushed
12. ndicator light 15 Emergency stop 16 Remote control connection 17 Charger mains power lead Co ae eS YS CO SLCC CC CCC CCC Intended use The overhead lift has been designed and tested for use indoors and it is classified as an IPX4 product The climatic conditions should be as follows ambient temperature from 0 C to 50 C relative ambient humidity from 30 to 80 and ambient pressure from 790 hPa to 1 060 hPa Product label The product label contains information about the lift This label is located on the front of the lift Homan Singel 5100 NA REF 50001 NA A lt 220kg lt 484lbs m 2012 06 24V DC 3 2Ah IPX4 Duty Cycle 15 85 Continuous max 6 min CE ATHY VUTEC TA A LAT AN 12345610001 Date of manufacture 2 Serial number asaJeoueLUNY MMM dluy The Singel 5100 and the Singel 4100 have been tested by an accredited test institute and comply with the necessary requirements in accordance with the medical devices directive for Class I products e Z The device is CE marked and has been tested in accordance with the requirements in the law on medical technical products according to the standards ISO EN 10535 ISO EN 60601 1 Electrical Safety and ISO EN 60601 1 2 EMC Conforms to ISO 10535 2006 ETL Classified with AAMI ES60601 1 2005 Certified to ISO 10535 2006 wi A C22 2 No 60601 1 th CS 08 AAA ZA8Y 48000 uapamg diojsyeyJels pe opz
13. rce required to operate the pushbuttons is 4 4N If the lift is loaded with more than approx 40 kg the lift will only run in the slower mode gt gt Charger The indicator on the lift flashes red when the batteries need recharging Plug the charger cable into the remote control 3 to start charging The list can only be used with a charger recommended by Human Care article number 50880 e Charge regularly preferably every night e The charger must be disconnected when using the lift e The unit is charged regardless of the position of the main switch If the lift is equipped with an emergency Stop button check that is not pushed in during charging See separate manual for the charger Indicator lamp The indicator lamp 14 has four indicating modes and it only works when the mains switch 10 is on Flashing green The lift is on and ready for use Constant green The lift is in operation or loaded Flashing red The lift needs to be charged Constant red The lift is blocked This happens during charging and if there is an error signal see troubleshooting table Belt tension guard The lift is equipped with a belt tension guard that prevents unintentional discharging of the lifting belt The lift must be loaded in order to be able to pull the belt out This means that when the lift is lowered to a surface the belt must be pulled out while pressing the DOWN button The purpose of this is to pull out t
14. rr rr nr nr rr nr rr rr nn 13 SMS ANG AC CCSS OU e E reder 14 AN Safety instructions Before using for the first time make sure that you have read and understood this user manual for the lift and all of its accessories the lift has been installed in accordance with the installation instructions the lift accessories are intended for use with the lift and are correctly fitted the lift s batteries have been charged for at least 6 hours Check to see if there is a distance strap suspended from the rail or if there is a hook fitted to the rail roller The recommended minimum height from the floor to the distance strap is 1850 mm Remove the lift 1 the charger 2 and the remote control 3 from the packaging Remove the seal from the lifting belt 6 after first reading the instructions Connect 16 the remote control 3 to the lift 1 Plug the charger 2 in at an easily accessible wall socket Plug the remote control 3 into the charger 2 If the indicator light is glowing yellow charge up until the indicator turns green oe ee The lift is designed only for lifting people and only one at a time Before use always ensure that e personnel who use the equipment have been given adequate tuition and training in use of the lift and its accessories e the lifting belt is not twisted or worn and that it can move freely in and out of the lift e there are no evident signs of wear and tear or other damage to the lifting a
Download Pdf Manuals
Related Search