A200 XPRESSO User Manual - Smart
Contents
1. Replace the drip tray 11 and ground coffee waste container 116 28 The system quickly heats up and is ready for use again MANUAL LIME SCALE REMOVAL If necessary the Lime scale removal program may be manually started even if the symbol does not appear See 5 4 above for the operational sequence Note If you unintentionally start up the Lime scale removal program you can interrupt it at the beginning of the cycle by pressing the On Off button 3 for about two seconds 5 5 GENERAL CLEANING Important Never submerge the appliance in water The unattached components are not dishwasher safe Do not use abrasive cleaners Clean the case inside and out using only a soft damp cloth Empty the drip tray 11 and the coffee grounds container 11e only when instructed to do so on the display or if the Float Level 11d is visible cleaning with warm soapy water occasionally Rinse out the water reservoir 1 every day and fill it with fresh cold water Dry residue accumulating on the nozzle after frothing milk can be hard to remove Thoroughly clean the Hot water Steam nozzle 9 with a damp cloth immediately after use The best way to do this is by repeating the steaming process with a glass of clear water ensuring that the nozzle stays clear of milk lactose build up CLEANING THE BREWING UNITS If necessary the brewing infusion unit 23 may be removed and rinsed under running water Impo2. cr me Symbol 3 Beans about 11 gr ground coffee for Espresso strong coffee 2 The strength may be altered by pressing and holding the 1 cup selector 4 or the 2 cups selector 5 until the desired strength appears on the display 6 3 WARNING Upon releasing these buttons brewing will automatically start to commence 3 3 BREWING ONE CUP OF COFFEE Place a pre heated cup underneath the coffee dispensing nozzle 10 The height of the coffee dispensing nozzle 10 may be precisely adjusted to suit the cup height 1 Set the desired water quantity as in 3 1 above 2 Press and hold the 1 cup selector 4 until the desired strength appears on the display 6 and release the selector 3 Atthis point the machine will begin the brewing infusion process 4 The process may be interrupted at any time by pressing the 1 cup selector 4 or 2 cup selector 5 Important If making coffee for the first time the grinding chamber is still empty After you grind coffee for the first time the Out of beans symbol D may flash on the display 6 and the machine may not make coffee If this happens press the 1 cup selector 4 again to repeat the process 3 4 BREWING TWO CUPS OF COFFEE NOTE Two grinds will automatically be performed by the machine upon making two cups of coffee 1 Place both cups under the coffee dispensing nozzle 10 Set the desired water quantity for one cup Press and hold the 2 cup selec
3. adjustable coffee dispensing nozzle 10 and press the steam preheat button 7 to rinse the system out At this point the On Off button 3 has lit up the beans button flashes D and the steam preheat button 7 is also lit up Once the rinsing process has finished the machine may continue to heat up The On Off huttan 3 will flash and the heans the disnlav 4 will he lit un 7 All four buttons 3 4 5 7 will now be lit up 8 The machine is now ready for use RECOMMENDATION Place a dish underneath the dispensing nozzle 10 to collect water upon rinsing the machine NOTE The machine is shipped ready to make its first cup of coffee However we recommend that you re program these main settings to suit your preferences Start by following the steps listed under 4 Programming heading to adjust the filter and water hardness settings 2 3 SETTING THE GRIND Important The grinder may be adjusted only when the coffee grinder is in the grinding operation The coffee grinder may be adapted to suit the roast of the coffee We recommend the medium setting for all roasts e With the coffee grinder in motion turn the Grind adjustment knob 15 to the desired position The smaller the dot next to the knob the finer the coffee grinds will be Remember lightly roasted coffee requires a finer grind dark roasted coffee requires a coarser grind Select the optimal setting for your personal requirements
4. coffee beans and close the lid again Please note Do not use coffee beans which have been treated with sugar or other additives during or after roasting as they could damage the coffee grinder Repair costs due to such damage will not be covered by the warranty The steam hot water knob 8 must be set off to 0 before operation Filling the system When you use the appliance for the first time the pipes inside the machine may not yet be filled with water the machine will signal this with symbol E Place a cup under the nozzle 9 and open the Hot water Steam Knob 8 till the unit stops or until no bubbles of air flows out e Please note This may need to be done every time the Water reservoir 1 runs out of water or air enters the system 2 2 USING YOUR MACHINE FOR THE FIRST TIME NOTE When using the appliance for the first time or if the appliance has not been used for some time the first coffee you make will not have perfect aroma and should be discarded 1 2 3 Remove the power cord from the cord compartment 17 and plug it into a suitable outlet Press the power switch 16 the on off button 3 will come on Press and hold the On off button 3 for at least one second On the display the beans symbol will light up and the On off button 3 will flash The system is heating up for a moment When the machine has heated up the steam preheat button 7 will light up Place a cup under the height
5. machine Place suitably sized container not to small under the hot water nozzle 9 and rotate the hot water knob 8 clockwise to the right The system will now perform a brief rinsing cycle Wait until the water stops flowing from the nozzle 9 and then turn the knob 8 anti clockwise to 0 The system may briefly heat up again and will then be ready for use again IMPORTANT The filter loses its effectiveness after about 50 liters of water Follow the instructions in section 5 2 Changing Filters to replace it Important If you have not used the machine very much you must replace the filter even if no indication appears on the display after a maximum of two months As a reminder you may set the replacement date on the wheel on the top of the filter For more thorough prevention of lime scale build up you should run the lime scale removal program at least once year even if you regularly use the resin based filter WITHOUT FILTER IMPORTANT Should you no longer wish to use an optional filter do not forget to set the water hardness accordingly These programming functions can only be performed when the On Off button 3 is set to OFF Standby The following settings can be programmed e Water hardness e Temperature e Standby time 4 2 WATER HARDNESS The frequency of lime scale removal depends on the hardness of your local water supply or whether or not a filter is used see 4 1 Set wate
6. minutes after which the machine will automatically stop the procedure To continue with the procedure turn the Steam hot water knob 8 back to 0 and then clockwise right In order to froth milk the metal tube 9 must be in its lowest position e Dry residue accumulating on the nozzle 9 after frothing is hard to remove Clean immediately after cooling preferably by repeating the frothing procedure with a cup of hot water e Warning danger of burns The steam is very hot Take care when handling the nozzle 9 ensuring only to touch the black plastic part of the nozzle 4 PROGRAMMING Use the following buttons for programming e On off Standby button 3 e 1 cup selector 4 e 2 cup selector 5 e Steam Preheat Button 7 4 1 THE FILTER optional FILTER USE OR FILTERED WATER USE A special water softening filter 21 for the water reservoir 1 can be ordered as an option If this filter is used correctly lime scale does not have to be removed as often Once the filter is in place set the water hardness onto level 1 see 4 2 below FILTER USE optional 2 Empty the Water Reservoir 1 Set the replacement date in months on the wheel situated on the top of the filter 21 Screw the optional filter 21 with the filter accessory tool 20 into the corresponding Supporting unit found inside the Water Reservoir 1 Fill the Water Reservoir 1 with fresh water and replace the reservoir into the
7. the machine to standby mode Press the 2 cup selector 5 for approximately four seconds The symbol corresponding to the correct standby setting will now be lit up By pressing the 2 cup selector 5 repeatedly the standby setting can be adjusted Confirm the standby time selection by pressing the standby button 3 To confirm the Settings the corresponding symbol will flash briefly Please note Should programming be interrupted for longer than 1 4 minutes the machine will automatically return to the ready to brew mode 5 NB CARE AND MAINTENANCE 5 1 Inserting a F ilter Please note See point 4 1 The Filter 5 2 Changing F ilters IMPORTANT The optional filter loses its effectiveness after about 50 liters of water If you have not used the machine very much you must still replace the filter even if no indication appears on the display after a maximum of two months Tip As a reminder you may set the replacement date on the wheel on the top of the filter 1 Empty the Water Reservoir 1 and unscrew the old filter 21 from the reservoir 2 Set the replacement date on the wheel situated on the top of the new filter 21 3 Screw the optional filter 21 with the filter accessory tool 20 into the corresponding Supporting unit found inside the Water Reservoir 1 4 Fill the Water Reservoir 1 with cold water and put it back into the machine 5 Place suitably sized container not to small under th
8. 3 PREPARATION 3 1 SELECTING THE WATER QUANTITY With the water volume adjustment knob 2 you can determine the ideal water quantity in your cup Turn anti clockwise to decrease water quantity small cup on the bottom left Turn clockwise to increase water quantity big cup on the bottom right RECOMMENDATION To determine the ideal water quantity for your taste or cup size proceed as follows when making your first cup of coffee 1 Set the water quantity adjustment knob 2 to the following positions Anti clockwise to the left for a cup of espresso Clockwise all the way to the right for a larger 2 Press and hold the 1 cup selector 4 or the 2 cups selector 5 until the desired strength appears the display 6 The machine will start making coffee upon releasing these buttons 3 Just before you reach the desired quantity of coffee in the cup turn the water quantity control knob 2 slowly anti clockwise to the left until the machine stops dispensing coffee 4 Notethe position shown on the water quantity adjustment knob 2 3 2 SELECTING COFFEE STRENGTH 1 As soon as the machine is ready for use a factory setting 2 beans will appear on the symbolic display 6 Y ou may set your preferred coffee strength to three levels indicated on the symbolic display 6 as follows Symbol A 1 Bean about 7 gr ground coffee for Caf latte cappuccino Symbol B 2 Beans about 9 gr ground coffee for Caf
9. Dear Customer Thank you for choosing our product With this coffee machine you will enjoy full taste and aroma right from the first cup and make creamy cappuccino as well as tea and other hot drinks Our product is made with top quality components to ensure quality and perfect safety Please read these Instructions carefully before using the machine IMPORTENT This appliance is not intended for use by persons incl children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning the use of the appliance by a person responsible for their safety MACHINE CONTROLS AND COMPONENTS 1 Removable W ater reservoir 2 Knob for adjusting amount of water in cup 3 On off button 4 1 cup selector 5 2 cup selector 6 Symbolic Display 7 Steam preheating button 8 Steam hot water knob 9 Steam nozzle with milk frothing accessory 10 Coffee dispensing nozzle with adjustable height ee Drip tray amp Grid a Drip Tray Grid c Coffee Grounds container d Red Float Level under Grid b If above grid requires cleaning 12 Cup Warming Shelf 13 Ground Coffee compartment 14 Coffee beans container 15 Grind adjustment knob 16 Power on off switch 17 Power cord compartment 18 Cover for accessing brewing infusion unit 19 Ground coffee measuring scoop 20 Filter assembly accessory 21 Water softe
10. OOTING Problem Meaning Solution Neither hot water nor Hot water Steam lean nozzle thoroughly steam is being produced Nozzle 9 is blocked Insufficient foam Unsuitable milk Usecold milk with alow fat produced Dry residue has content accumulated in andon Thoroughly clean the Hot water the Hot water Steam Steam nozzle 9 by repeating nozzle 9 the steaming process with a glass of hot water Only afew drops of Thegrind being usedis Set to acoarser grind 15 coffee are being too finefor the typeof Usea coarser ground coffee produced coffee beans Thepre ground coffee being used is too finely ground The coffee produced has Unsuitable type of Change the type of coffee used no creme coffee is used Usefreshly roasted coffee Coffee beans are no Adjust knob 15 to change the longer fresh grind setting of the machine Inappropriate grind setting for the coffee type Grinder motor is very foreign objecthas Contact the service department noisy reached the grinder Continue only with pre ground coffee On Off button 3 flashes The brewing infusion Switch the machine off at the with increasing unit may be blocked power switch Switch it on frequency and the steam again If the problem persists button 7 flashes contact the service department Please note Should
11. ale removal Do not use any substance not authorized by the manufacturer only use the special XPRESSO Lime Scale Remover descaling tablets or the Lime O Powder available from XPRESSO Direct 662 906 8118 1 Press the On Off button 3 to set the machine to the standby mode 2 Simultaneously press the On Off Standby button 3 and the 2 cup selector 5 for approximately four seconds 3 Symbol H will light up indicating that the drip tray 11 needs to be emptied 4 Completely removed the drip tray 11 and the ground coffee waste container 110 and clean it thoroughly Important This step cannot be skipped 5 Replace the drip tray and ground coffee waste container 6 Thesymbol Fill Water Reservoir and the 1 cup selector 4 will flash 7 Fill the Water Reservoir 1 with one packet of the XPRESSO Lime Scale Remover descaling tablets or the Lime O Powder and fresh water up to the litre mark and replace into the machine Note If the optional Water Filter 21 is installed remove it before descaling Also do not use the Sprada Cleaning Tablets in place of the Lime O Descaling Powder or tablets 17 18 19 Place a suitably sized container about litre under the coffee outlets 10 Press the flashing 1 cup selector 4 The Lime scale removal process will now begin The first phase of the lime scale removal process takes approximately twelve minutes The symbol G Hot water Ste
12. am on off will begin to flash Place a suitably sized container under the nozzle 9 and turn the Hot water Steam knob 8 clockwise to the right The second phase of the lime scale removal process takes approximately ten minutes Once this cycle is complete symbol Empty drip tray ground coffee waste container 11c and symbol E Fill water reservoir will light up Remove and empty the drip tray 11 Symbol Empty drip tray ground coffee waste container will flash and the symbol Fill water reservoir will be lit Symbol E Fill water reservoir as well as the 1 cup selector 4 will flash Remove and clean the water reservoir 1 Fill the water reservoir 1 with clean fresh water and replace Press the flashing 1 cup selector button 4 The system will now be washed through the Steam Hot water nozzle 9 Once the washing process is complete symbol Empty drip tray ground coffee waste container will flash 23 Turn the Hot water Steam knob 8 off anti clockwise back to the left position marked 0 24 gt The internal rinsing process will now begin and takes about 1 minute 25 The symbol Empty drip tray ground coffee waste container will appear 2 D Remove and empty the drip tray 11 symbol H Empty drip tray ground coffee waste container will flash
13. e Hot Water nozzle 9 and turn the Hot Water knob 8 clockwise to the right The system will perform a brief rinsing cycle 6 Wait until the water stops flowing from the nozzle 9 and then turn the knob 8 anti clockwise back to 0 7 Thesystem may briefly heat up again and will then be ready for use again 5 3 CLEANING PROGRAMME IMPORTANT Please follow these instructions step by step The cleaning program thoroughly cleans all dispensing assemblies removing coffee residues and oily deposits which can build up and block up the machine To run the program use the special Sprada Cleaning Tablets available through Sprada Direct IMPORTANT This program is intended solely for cleaning the coffee dispenser and brewing unit It is not a lime scale removal process e When the machine requires a clean the symbol J Clean M achine will appear on the display The cleaning symbol will continue to flash through the duration of the cleaning cycle until it has been completed successfully RECOMMENDATION Y ou may continue making coffee hot water and steam but we recommend you perform the cleaning cycle promptly IMPORTANT The cleaning program cannot be interrupted once it has started 1 2 Press the On Off button 3 to set the machine to the standby mode Simultaneously press the standby button 3 and the 1 cup selector 4 for approximately four seconds Symbol H will light up indicating that the dr
14. e appliance near a live element an electric stove or any other source of heat Do not expose the appliance to extreme temperatures Never let children or people who are not familiar with how it works use the appliance Do not press the buttons hard or with a pointed object such as pen Always rest the appliance horizontal stable and flat surface that is resistant to any water leakages In case of an accidental fall of the appliance it is necessary to have it checked by an authorized service centre as the internal safety features may have been negatively affected In case of breakdown or malfunction switch off the appliance and never attempt to disassemble it but refer to an authorized service centre In order to avoid prejudicing the safety of the appliance use only original spare parts and accessories approved by the manufacturer Do not wind the power cord around the appliance especially when the appliance is stil hot or is still in use Do not use lime scale removers which are not authorized by the manufacturer Always fill the water reservoir with cold clean water Do not use milk or any other liquid Do not wash coffee machine accessories in the dishwasher Do not direct the steam jet at electrical appliances Let the appliance cool down before cleaning the hot water nozzle Never place your hands inside the jet of steam Danger of burns Do not direct the steam jet at people animals or debris Danger of burns Never u
15. e is connected must always comply with the laws in force e Before connecting the appliance make sure that the mains voltage is the same as the voltage indicated on the data label of the appliance and that the power outlet is connected to an earth Always turn off the appliance at the main on off switch 16 at the rear of the machine before unplugging it Turn off the power only when the on off button 3 is set to off in stand by mode Do not pull the power cord out of the socket but grasp the plug itself to avoid damage to the socket Do not allow the power cord to be twisted crushed stretched or come into contact with sharp or hot surfaces Do not use the appliance if the power cable or other important parts are damaged Do not use electric extension leads that are not authorized by the manufacturer as they may cause damage or fire f itis necessary to replace the power supply cable please refer to the nearest Sprada S A authorized service centre since the use of a special tool is necessary Do not use the appliance near a bathtub shower or container full of water Never immerse the appliance the cable or the plugs in water or any other liquid Use of the appliance in places where there is a danger of explosions is prohibited Do not use the product with toxic substances Do not place hot appliances on surfaces sensitive to heat Do not leave the appliance exposed to wind or rain or immerse in water Do not place th
16. illing compartment 13 is not a ground coffee storage compartment Never put more than one scoop into it and use only freshly ground or vacuum packed coffee Do not use instant coffee Y ou can make instant coffee in the cup using the Hot W ater nozzle 9 see 3 6 below 3 6 DRAWING HOT WATER 1 Place a cup under the Hot W ater nozzle 9 2 Turn the Steam H ot W ater knob 8 clockwise to the right 3 Fill the cup to the desired level and then set the knob 8 anti clockwise to 0 again Important Danger of burns Hot water may splash The nozzle 9 reaches high temperatures while in use Let it cool down for afew minutes before touching it for any reason 3 7 DRAWING STEAM AND FROTHING MILK 1 Press the Steam preheat button 7 The On Off button 3 will light up and the Steam button 7 will flash When the steam temperature has been reached the steam button 7 will light up mmerse the nozzle 9 in the cup containing the milk to be foamed or heated Turn the Steam hot water knob 8 clockwise open to the right Important A little amount of water will come out before the steam This is normal During the steaming process the Steam button 7 will flash Upon completion turn the Steam hot water knob 8 anti clockwise back to 0 to stop the steam flow Press the Steam preheat button 7 to restore normal operation of the machine Please note Steam may continue to be produced for approximately 3
17. ip tray 11 needs to be emptied Completely removed the drip tray 11 and the ground coffee waste container 11 and clean it thoroughly Important this step cannot be skipped Replace the Drip Tray 11 and Coffee Grounds Container 110 Symbol Ground Coffee will light up Open the lid of the Ground Coffee compartment 13 Symbol F Ground Coffee will now start to flash p oO YO Fe OD me Fs Wo A Place one XPRESSO Cleaning Tablet in the ground coffee compartment and close the lid Important Do not put the cleaning tablet in the Water Reservoir 1 Both symbols Fill Water Reservoir and the 1 cup selector 4 will flash Fill the Water Reservoir 1 with fresh water up to the litre mark and replace into the machine Place suitably sized container about 22 litre under the coffee outlets 10 Press the 1 cup selector 4 The cleaning procedure will now begin The cleaning process is fully automatic and takes approximately ten minutes Once the cycle is complete the symbol empty drip trays will light up Remove the drip tray 11 Symbol empty drip trays will start to flash Empty and replace the drip tray 11 The machine will briefly heat up if required The On Off button 3 will flash and the beans symbol will light up The system is ready for use again MANUAL CLEANING If necessary the cleaning program may be run eve
18. l RAMANA 22 23 WITHOUT FILTER 24 ree aa serine eerie ae erm 25 TATEM PERA TUR Eeen T 28 TIM 29 5 NB CARE AND MAINTENANCE sssaaa 30 5 1 Inserting a Filter 30 5 2 Changing RII aaa 30 BUEN N Ge PROGRAMM E 31 BoA LIME SCALE REMOVAL sisisi 35 SS GENERA 39 OMESSA OES M nnn nn en mre ss 41 SHOOTIN 43 8 USEFUL INFORMATION issis 45 4 1 SAFETY INSTRUCTIONS CORRECT USE OF THE PRODUCT This appliance is intended for home use in accordance with the descriptions and instructions contained in this manual Please read the instructions carefully and keep them as they could be useful to you in the future IMPORTENT This appliance is not intended for use by persons incl children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning the use of the appliance by person responsible for their safety KEEP THESE INSTRUCTIONS e Read these instructions for use carefully before using the appliance e Use of this Sprada product which does not comply with these instructions will invalidate the warranty e Thewiring system to which the applianc
19. losed during the lime scale removal cycle Symbol E Water reservoir 1 is empty Fill with fresh water flashes Water reservoir 1 has not been Insert W ater reservoir 1 inserted correctly correctly Symbol E Water reservoir 1 was pumped Fill the Water reservoir 1 is lit empty while brewing with water little lime scale remover or Fill the Water Reservoir 1 rinsing water was poured in with water Symbol D No beans in the Coffee Beans Fill the coffee beans container Flashes Container 14 14 with beans Symbol H TheDrip tray 11 and or coffee Empty the Drip tray 11 flashes grounds container 110 is full and or coffee grounds Cleaning and lime scale removal is in progress container 110 Insert coffee grounds container 11c and water reservoir 1 Symbol Drip tray 11 and ground coffee Insert Drip tray 11 and is lit waste container 11c is not present or ground coffee waste container is incorrectly installed 11c Cleaning and lime scale removal in progress Allow programme cycle to complete Symbol J Cleaning is required Clean the machine See point is lit 5 3 Symbol I Lime scale removal required Remove lime scale See point flashes 54 Symbol F Ground coffee compartment s lid 13 Close lid 13 flashes 15 open Symbol F Lid 13 was opened while a Close lid 13 is lit programme was running 7 TROUBLESH
20. n if the symbol does not appear See 5 3 above for the operational sequence Note If you unintentionally start up the cleaning program you can interrupt it at the beginning of the cycle by pressing the On Off button 3 for about two seconds 5 4 LIME SCALE REMOVAL IMPORTANT Please follow these instructions step by step The lime scale removal program thoroughly removes all lime scale from the system which can build up and block up the machine To run the program use the special XPRESSO Lime Scale Remover descaling tablets or the Lime O Powder available from XPRESSO Direct 662 906 8118 e When the machine requires lime scale removal symbol 1 will appear the display e These symbols will continue to flash through the duration of the removal cycle until it has been completed successfully e RECOMMENDATION Y ou may continue making coffee hot water and steam but we recommend you perform the descaling cycle promptly IMPORTANT Thelime scale removal program cannot be interrupted once it has started Note If you do not use the optional filter 21 or use filtered water regularly itis essential to remove lime scale in the appliance at least once every two months so as not to compromise the functionality of the appliance with time Note Never use sulphuric acid or any other product containing this acid as it may compromise the functioning of the appliance Do not use vinegar or vinegar based products for lime sc
21. ning filter optional 22 Litmus Paper 23 Brewing Infusion Unit 24 Handle 25 Red Switch We in accordance with its policy of continuous improvement reserves the right to make any technical and structural modifications without prior notice Display Number Description Symbols A Coffee strength Mild B Coffee strength Normal Coffee strength Strong 28 No coffee beans refill container S E Fill the water reservoir F Ground coffee G Hot water steam on off priming the system H Drip tray incorrectly inserted or missing Remove lime scale build up from machine Clean machine TABLE OF CONTENTS PLEASE NOTE Maintenance and Care 5 please follow these instructions carefully TESA PEIN ST BUG TON S tess 5 2 OPERATIONAL START UP issis 10 7 PREPARING THE CORFE EMA 10 POUR MACHINEFOR THE FIRSTETIM E 13 PREPARATION 14 3 1 SELECTING THE WATER QUANTITY sssri 14 3 2 SELECTING CORRE E 15 3 3 BREWING ONE CUP OF COFFEE sssaaa 16 eT 17 3 5 BREWING WITH PRE GROUND COFFEE ussiisa 18 19 3 7 DRAWING STEAM AND EROTH ING MILK 20 A PROGRAM 22 4 1 THE FILTER optiona
22. r hardness correctly as soon as you begin using the machine so that the system will be able to inform you when the lime scale procedure is necessary Note First test the water using the litmus paper 22 supplied The factory setting corresponds to level 3 1 Fill a small container with tap water Dip the litmus paper 22 into it and remove it immediately then gently shake off the excess water 2 After about one minute you will be able to read the results by counting the red dots The different levels and their corresponding dots are determined as follows Litmus Paper Hardness Symbols Settings 1 red dot 1 7 dH 1 12 6 fH Standby button is lit 2 red dots 8 14 dH 12 7 25 2 fH Standby button 1 cup selector is lit Standby button 1 cup selector 2 cup 3 red dots 15 21 d H 25 3 37 8 FH selector is lit Standby button 1 cup selector 2 cup 4 red dots gt 21 q H gt 37 8 TH selector Steam button is lit Please note When no points appear on the litmus paper set the machine onto level 1 Set 3 4 the machine to the Standby mode Press the Steam Preheat button 7 for approximately 4 seconds The water hardness will be indicated by the number lit symbols as described in the table above Press the Steam Preheat button 7 repeatedly until the desired level flashes Confirm by pressing the On Off button 3 To confirm these settings the corresponding
23. rtant Do not use any cleaning products or abrasive cleaners 1 Press the On Off button 3 to set the machine into the standby mode 2 Remove the Cover 18 for accessing the Brewing infusion unit 23 on the right hand side 3 Unlock the Brewing Infusion unit 23 by pressing the red switch 25 and turning the handle 24 clockwise to the left until the stop position has been reached 4 Grasp the brewing infusion unit 23 by the handle 24 and pull it out The On Off button 3 and Steam H ot water button 7 will flash confirming the removal 5 Rinse the brewing infusion unit 23 out to clean it Important Only water is to be used 6 Replace the brewing infusion unit 23 7 Press the red lever switch 25 and turn the handle 24 anti clockwise to the right until the stop position has been reached 8 Replace the cover 18 MESSAGES FROM THE SYSTEM M essage Meaning What to do Symbol G Rinse the water conveyance system Open the hot water knob 8 Flashes Lime scale removal process is clockwise complete Close the Hot water Steam knob 8 Symbol G Hot water Steam knob 8 was Close the Hot water Steam is lit opened while a programme was knob 8 running Fill the reservoir and open the little lime scale remover was Hot water Steam knob 8 poured in Open the Hot water Steam Hotwater steam knob 8 was knob 8 accidentally c
24. se beans treated with additives such as sugar or similar substances This appliance is built according to current regulations for recycling Do not throw away the packing materials used to protect the appliance during transportation but take them to relevant collecting centers Use only original spare parts Weare declines liability for any damage or accident derived from any use of this appliance which is notin conformity with the instructions contained in this booklet IMPORTANT Important Flipping the power switch 16 while infusion is in progress may result in damage to the appliance All our products undergo strict quality control before leaving the company CE This appliance conforms to the following EC directives e 72 23 EWG from 19 02 1973 e 93 68 EWG e 89 336 EWG from 03 05 1989 e 02 31EWG Technical information Supply V oltage 220 240 VAC Power Input 1400 Watt 2 OPERATIONAL START UP 2 1 PREPARING THE COFFEE MACHINE Carefully remove the machine and all accessories from the packaging Please note it is advised that the original packaging is kept for future transporting Remove the Water reservoir 1 and rinse with clean cold water Fill the reservoir no higher than the M AX mark place it back in the machine ensuring that the reservoir is positioned correctly and close the lid Please note Do not use sparkling water or any other liquid Open the lid of the coffee bean container 14 fill it with
25. symbols will flash again twice Programming water hardness is now completed and the system is now ready to use Please note Should programming cycle be interrupted for longer than 1 4 minutes the machine will automatically return to the ready to brew mode 4 3 TEMPERATURE Y ou may alter the temperature of the coffee to suit your preferences The factory setting is on HIGH e Normal Standby button 3 lit e High Standby button 3 1 cup selector button 4 lit 1 Set the machine to the Standby mode 2 Press the 1 cup selector button 4 for approximately four seconds 3 Thesymbol corresponding to the correct temperature setting will now be lit up 4 pressing the 1 cup selector 4 repeatedly the temperature setting can be adjusted 5 Press the standby button 3 to confirm the selection of the desired temperature To confirm the selected setting the corresponding symbols will briefly flash Please note Should programming be interrupted for longer than 1 minutes the machine will automatically return to the ready to brew mode 4 4 STANDBY TIME This function allows you to determine how long the machine waits after the last operation before returning to the standby mode The following settings are possible 1 hour Standby button 3 is lit 3 hours Standby button 3 1 cup selector button 4 is lit 5 hours Standby button 3 1 cup 4 2 cup 5 selectors are lit Set
26. team is emitted turn the steam hot water knob 8 anti clockwise back to ug 5 Switch off Power On Off switch 16 at the rear of the machine for storage or transporting 9 CONTACT INFORMATION Replacement parts and accessories e A new freshwater filter can be obtained from Sprada Direct e Cleaning tablets can be obtained from Sprada Direct e Descaling Lime Scale Remover descaling tablets or the Lime O Powder can be obtained from Sprada Direct Our products are subject to the highest quality standards Should you have any further questions with regard to the use of this appliance please feel free to write fax or email us It is only with the support of our customers that we are able to further develop and improve our products and thereby fully meet your requirements XPRESSO Tel 66 2 906 8118 Fax 66 2 906 3200 Email info xpresso coffee com Web www xpresso coffee com
27. tor 5 until the desired strength is shown on the display 6 and release the selector At this point the machine begins the brewing infusion process and makes two cups of coffee automatically in a row The process may be interrupted at any time by pressing the 1 cup selector 4 or 2 cup selector 5 NOTE If the machine should run out of water or coffee beans between the two cups or if the trays need emptying a signal will appear and the second cup of coffee will not be made Follow the instructions to top up the machine and press only the 1 cup selector 4 to make the remaining second cup of coffee 3 5 BREWING WITH PRE GROUND COFFEE 1 First turn the water quantity control knob 2 to the desired quantity of water for one cup 2 Open the lid to access the ground coffee compartment 13 3 Fill with a level measuring scoop 19 of ground coffee and close the lid 13 The symbol F will appear on the display 6 4 Place the cup under the coffee dispensing nozzle 10 and press the 1 cup selector button 4 5 Atthis point the machine will begin the brewing infusion process Please note If you unintentionally open the ground coffee compartment and do not press the coffee button after putting ground coffee into it the machine will automatically perform a washing cycle through the coffee dispensing nozzle 10 one minute after the lid is closed and will then be ready for use again Important The Ground coffee f
28. you be unable to solve the problem yourself please phone our service departme during office hours For further information contact our service department XPRESSO service Tel 66 2 906 8118 Fax 66 2 906 3200 8 USEFUL INFORMATION CHOOSING COFFEE A true espresso coffee is recognizable by its dark colour typical crema and it s rich flavors The flavor and aroma of a coffee bean are the result of a roasting process Darker coffee beans have been roasted for a longer time at a higher temperature and more aromatic than lighter coffee beans There are many different types of coffee available on the market containing blends of beans roasted at different temperatures with different types of aroma There is also decaffeinated coffee containing only 2 caffeine Try using different types of coffee with your espresso machine to find the flavors and aroma that best suits your unique taste Ideally coffee beans should be ground just before using them Remember that your coffee MUST BE GROUND FOR PUMP ESPRESSO MACHINES which means it must be ground quite finely It is good idea to Keep ground coffee in a hermetically sealed container Coffee easily absorbs odours and looses oils TRANSPORTING AND STORAGE For transporting and storage this appliance must be prepared 1 Remove all water from the reservoir 1 2 Press the steam button 7 3 Turn the steam hot water knob 8 clockwise to the right 4 more s
Download Pdf Manuals
Related Search