Home
USER MANUAL - SENA Home Page
Contents
1. Purpose Clear the list of Bluetooth devices sharing the pin code Description This clears the list of Bluetooth devices with link key in flash memory To take effect of this command ATZ or power off and on because the main memory still has the list Reference AT BTFP AT BTKEY AT BTSD AT BTSEC ATZ AT amp F 23 AT BTFP n SD Response WOK Purpose Set generation of link key every time of connection Parameters n 0 Inactivate Default n 1 Activate Description If n is set to 1 Promi SD asks pin code every time of connection This is used to level up the security Reference AT BTCSD AT BTKEY AT BTSD AT BTSEC ATD ATZ AT amp F 24 AT BTSEC Authentication Encryption SD Response WOK Purpose Set authentication and data encryption Parameters Authentication 0 Inactivate Default Authentication 1 Activate Encryption 0 Inactivate Default Encryption 1 Activate Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands A 10 Description If the authentication is activated the pin code must be set by AT BTKEY command Data encryption cannot be used when authentication is not activated i e Authentication 0 and Encryption 1 is not valid Reference AT BTCSD AT BTFP AT BISD AT BTSD2 ATZ AT amp F 25 AT BTNAME stringe SD Re
2. Purpose Wait for connection by the Bluetooth device with given BD address Parameters 112233445566 BD address to time duration in seconds Description For the given to Promi SD is waiting for the connection from the Bluetooth device with the given BD address If the parameter of to is 0 it will wait forever When connection is made with the Bluetooth device SD response will be CONNECT with its BD address If there is no connection made within this time duration SD response is ERROR and the operation status becomes to Standby Reference ATD AT BTINQ2 AT BTCANCEL Example AT BTSCANOO00B53001 1 FF 30 17 ATDe SD Response WOK CONNECT 112233445566 or KY RROR amp Purpose Connect to the last connected Bluetooth device Description Promi SD saves the BD address of the Bluetooth device most recently connected ATD can make connection to it without input its BD address If it fails to make connection SD response is ERROR Reference AT BTINQ2 AT BTSCAN 18 ATD112233445566 SD Response WOK CONNECT 112233445566 or KY RROR amp Purpose Connect to the Bluetooth device with given BD address Parameters 112233445566 BD address Description Promi SD attempts to connect to the Bluetooth device with the given BD address To make successful connection the Bluetooth device must be in Page scan This attempt continues for 5 minutes If it fails to make
3. e Do not use excessive force on the buttons or attempt to disassemble the device Damage to your products may result from improper use e Do not place heavy objects on the product Damage to your products moy result from improper use General Terms and Conditions of Sale 1 GENERAL These general terms and conditions of sale along with any associated written specification quotation and or supplemental terms and conditions provided by Seller exclusively will govern the sale or licensing by Seller of all goods and services including without limitation hardware firmware and software products training programming maintenance engineering parts repair and remanufacturing services hereinafter Products furnished to Buyer hereunder whether such sale or licensing is effected by paper based transactions or via facsimile or other forms of electronic data interchange or electronic commerce and represents the entire agreement between Buyer and Seller with respect thereto Buyer s receipt or acceptance of delivery of any of the Products ordered or purchased hereunder will constitute its acceptance of these terms and conditions No addition or modification to these terms and conditions will be binding on Seller unless agreed to in writing signed by an authorized representative at Seller s headquarters Seller objects to and rejects other terms and conditions that may be proposed by Buyer or that appear on or are referenced in Buyer s purchase order
4. 2 Configurations Operation Modes LED Indicators EE Serial Port Geen Reset to Factory Defaults PromiWizard Geen PromiWIN Terminal Program Dip Switch SD205 only Pairing Button SD205 opleen 22 3 Connections RS232 Interface nnn 24 Pin Assignment ee 25 Power Supply En 26 4 Trouble Shooting No Data Transmission 28 Data Loss or Malfunctioning 28 Transmission Delay 28 5 Specifications Bluetooth 30 Serial Interface 30 Power Mechanical Dimensions 30 Environmental Default Antenna Power Consumption Wireless Coverage Battery SD101 only Appendix A AT Commands Terminology Command Category Command Description Command Validity Appendix B S Register Appendix C Technical Support Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Before Using the Product 2 Before Using the Product Welcome Copyrights Certification Limited Liability Precautions and Safety General Terms and Conditions of Sale UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manua
5. Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 18 PromiWIN PromiWIN is a program running on Microsoft Windows for the configuration of Promi SD Install PromiWIN on your computer Plug a Promi SD into the serial port of the computer and turn on the power Run PromiWIN Application Setting Please setup serial port for configuring Promi SD Serial Port com d BaudRate x Parity None StopBit hd Set each option properly and click Confirm If the settings are different from the host computer error message will pop up If the Promi SD is in the status of connection warning message will pop up Then the current connection can be cancelled by 424 al dl button on the main window Error Notice Initialization Failure Confirm PromiWiN has been configured to be identical with Promi SD and the physical connection of Promi SD to this PC Serial port was open COM 1 S600 No Parity One Stopbit PromiWiN a Search Result Information Device Address _ Device Name s Device Setting Lonnection out Cannection in B a Search py Define the number of nearby devices to be searched 0266 Connect to Specified devices Disconnect Drop the Connection Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 19 Serial port was open COM 1 S600 No Parity One Stopbit PromiWiN d D
6. 3 dip switches are used for setting baud rate and bottom dip switch is used for setting hardware flow control option If the baud rate needs to be set out of the range given below PromiWIN or terminal program should be used for extended AT commands At this time combination of dip switches must be complied with AT cmd Then baud rate will go back to 9600 as default Baud 2400 4800 9600 19 2K 38 4K 57 6K 15 2K AT cmd Rate EEN ES E __ E J Hardware Flow Control No use Use Handshaking Pairing Button Promi SD205 only Promi SD205 provides Pairing Button for instant configuration without PC to make an automatic connection between two Promi SD205s For convenience sake name two Promi SD205s as SD1 and SD2 respectively Turn off all the nearby Promi SD ESD 1 2 3 CR 00 EE SS Turn on SD1 and SD2 and hardware reset both of them by pressing Reset Button Press the Pairing Button of SD1 for 2 seconds until Standby LED of SD1 blinks 3 times every 3 seconds Keep the power ON Press the Pairing Button of SD2 for 2 seconds until Standby LED turns off and Con
7. 5 Specifications 29 5 Specifications Bluetooth Serial Interface Power Mechanical Dimensions Environmental Default Antenna Power Consumption Wireless Coverage Battery UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 5 Specifications N Bluetooth Interface e Bluetooth 1 1 specification compatible and qualified Protocol RFCOMM L2CAP SDP e Profiles Serial Port Profile Generic Access Profile Service Discovery Profile e Radio Frequency 2 4 2 4738GHz e Number of Channels 79 e Transmission Power Class 2 Promi SD101 e Transmission Power Class 1 Promi SD202 SD205 ESD Data Transmission Rate 380Kbps Max N Serial Interface e EIA RS232C Standard e Connector DB female e Data Transmission Rate 1 200 230 400bps e Hardware Flow Control On Off N Power d DC 5 12V Constant Voltage H Supply DC Jack or Pin 9 of DB N Mechanical Dimensions N Environmental e Recommended Operational Temperature 207 70 e Recommended Operational Humidity 90 Max Non condensing Copyright 2006 Sena Technologies Inc All rights reserved 30 Promi SD User Manual 5 Specifications 31 N Default Antenna e Type Helical e Frequency 2 400 2 485GHz e Gain Max 1dBi 1 e Impedance 50 2 e size 30mm x 9mm WXD e weight 3 5g x Power Consumption The power consumption varies according to the operation statu
8. F SD Response OK 7 Purpose Hardware reset Description This is the same effect as initialization by reset button All parameters are initialized to factory defaults The storage of Promi SD is cleared completely Reference ATZ 3 Af SD Response WOK Purpose Check the connection status with host equipment Description Check if the connection to host equipment is normal The serial parameters of Promi SD must be same as those of host equipment If not SD response is none or ERROR or abnormal sequence of strings Reference AT UARTCONFIG ATZ AT amp F 4 AT UARTCONFIG Baudrate Parity Stopbit Hwfc SD101 202 AT UARTCONFIG Baudrate Parity Stopbit SD205 SD Response OK7 Purpose Set Serial parameters Parameters Baudrate 1200 2400 9600 14400 19200 38400 57600 115200 230400 Default 9600 Parity N E O Default N Stopbit 1 2 Default 1 Hwfc Hardware Flow Control 0 1 Default 1 Only SD101 202 SD205 use dipswitch Description The Serial parameters can be set or changed The factory default is 9600 N 1 To take effect of this command ATZ or power off and on Reference AT ATZ AT amp F ATS Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands Example AT UARTCONFIG 38400 E 1 1 SD101 202 AT UARTCONFIG 9600 N 1 SD205 5 AT USEDIP SD205 only SD Response mn Purpose Check the Baud
9. Manual 5 Specifications e Can be charged up to 500 times approximately Copyright 2006 Sena Technologies Inc All rights reserved 32 Promi SD User Manual Appendix A AT Commands A 1 Appendix A AT Commands Terminology Command Category Command Description Command Validity UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands Terminology N AT Command AT command set is the de facto standard language for controlling modems The AT command set was developed by Hayes and is recognized by virtually all personal computer modems Promi SD provides the extended AT command set to control and configure the serial parameters and Bluetooth connection AT Response Promi SD replies to AT commands with 4 kinds of message OK ERROR CONNECT and DISCONNECT Operation Mode e Mode0 Waiting for AT commands e Model Attempting to connect to the last connected Bluetooth device Mode2 Waiting for the connection from the last connected Bluetooth device e Mode3 Waiting for the connection from any other Bluetooth devices Operation Status e Standby Waiting for AT commands e Pending Executing tasks S Connect Transmitting data Security e Authentication Pin code or Pass key V Encryption Data encryption Symbols The symbols are used for the description of command syntax as follows Symbol Mea
10. connect the last connected Bluetooth device Promi SD in Model is to be a master and tries to connect the last connected Bluetooth device Promi SD always stores the BD address of the Bluetooth device to which Promi SD has connected last time When Promi SD is initially used or after hardware reset there is no BD address stored in Promi SD In this case Model does not make any sense and mode change from other operation modes to Model is not allowed The mode change to Model can be made after Promi SD succeeds to connect to other Bluetooth device in Mode Once changed to Model Promi SD will try to connect automatically the last connected Bluetooth device whenever power on or software reset Promi SD in Model cannot be discovered or connected by other Bluetooth devices N Mode Promi SD is waiting for the connection from the last connected Bluetooth device Promi SD in Mode2 is to be a slave and waiting for the connection only from the last connected Bluetooth device Just like Model if there is no BD address stored in Promi SD the mode change from other operation modes to Mode is not allowed Once changed to Mode Promi SD will wait for the connection from the last connected Bluetooth device whenever power on or software reset Promi SD in Mode2 cannot be discovered or connected to Bluetooth devices other than the last connected device N Mode3 Promi SD is waiting for the connection from any other Bluetooth devices Promi SD in Mode3 a
11. connection SD response is ERROR Reference AT BTINQ Z AT BTSCAN Example ATDOO0B53001 1 FF 19 ATH SD Response WOK DISCONNECT Purpose Release the current connection Description The current Bluetooth connection is released normally It takes about 30 seconds to detect an abnormal disconnection such as power off and moving out of service range Reference ATD AT BTSCAN Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands 20 AT BTKEY stringe SD Response WOK Purpose Change pin code Parameters string New pin code Default 1234 Description Pin code is a string which allows 16 alpha numeric characters maximum Based on this pin code Promi SD generates a link key which is used in actual authentication process Reference AT BTCSD AT BTFP AT BTSD AT BTSEC ATZ AT amp F Example AT BTKEY apple 21 AT BTSD SD Response 21 122334455662 KF Purpose Display the list of Bluetooth devices sharing the pin code Description Once a connection is made with pin code Promi SD saves the Bluetooth device with its link key generated by pin code The connection to a device listed in Promi SD can be made automatically without authentication process The maximum number of the list is 5 Reference AT BTCSD AT BTFP AT BTKEY AT BTSEC ATZ AT amp F 22 AT BTCSD SD Response WOK
12. in icon will show the following window to make Promi SD wait to a connection from the other Bluetooth device The waiting time in seconds can be controlled With O input for this waiting time Promi SD keeps waiting for connection until Cancel button is clicked Serial port was open COM 1 S600 No Parity One Stopbit PromiWiN 1 Option Information Other Bluetooth Devices can discover this Promi SD Inquiry scan po Allow other Bluetooth Devices to Connect Page scan DOE Seconds for waiting connection If you set the time for waiting connection to D it will wait infinitely Connection out 300 Second a Status LG Waiting Connection Connectiontin Terminal Program A terminal program is an application that will enable a PC to communicate directly with a modem If you are using Windows 98SE or higher version of Windows HyperTerminal program as it is included as part of the operating system Promi SD provides some extended AT commands for its configurations on terminal program This manual will explain the method using HyperTerminal If you need to install HyperTerminal click start gt setting gt control panel gt add remove programs For more precise information please refer to Help of Microsoft Windows Attach Promi SD to serial port of host computer and power on Check Status LED Promi SD101 202 or Standby LED Promi SD205 is lit in green Launch HyperTerminal It can be found in start gt programs gt accesso
13. rate set by dip switch Description m 0 Set to AT cmd m 1 Set to other than AT cmd Reference AT ATZ AT amp F ATS 6 AT BTINFO SD Response 41 12233445566 DeviceName Mode Status Auth Encryp FlowControl 4 KF Purpose Display Bluetooth settings Description The current Bluetooth settings are displayed including BD address Device name Operation mode Operation status Authentication Data Encryption and Hardware Flow Control The initial value of Device name is PSDv3b 445566 PSD stands for Promi SD v3b for the version of firmware and 445566 for the last 6 digits of BD adaress Mode MODE0O MODE1 MODE2 MODE3 Status STANDBY PENDING CONNECT Auth 0 1 Authentication is not activated when 0 Encrypt 0 1 Encryption is not activated when 0 FlowControl HWFC NoFC Reference AT BTNAME AT BTMODE AT BTSEC ATS142 Example 4000B53001 1FF SENA MODEO PENDING 1 1 HWFC 7 AT BTINQ SD Response 21 12233445566 FriendlyName CoD 41 12233445566 FriendlyName CoD 21 12233445566 FriendlyName CoD WKS Purpose Search Bluetooth devices nearby Description The Bluetooth devices in Inquiry scan mode nearby are displayed with their BD addresses Device names and Class of device Maximum 10 devices are scanned for 30 seconds Reference AT BTSCAN ATD AT BTINFO 8 AT BTLAST SD Response 21 122334455667 KE Purpose Display the BD address of t
14. same kind devices and can be placed conveniently into any devices or equipments Its detachable antenna of variety optimizes the quality and distance of wireless communications N Easy Configuration and Adaptation Promi SD can be configured and controlled by typical AT commands User can easily configure Promi SD on the terminal program such as HyperTerminal and implements the wireless communication without modifying user s existing serial Communication program In addition to the basic AT commands Promi SD provides some expanded AT commands for its various functions User friendly PromiWizard and PromiWIN are also provided for easy setup on Microsoft Windows For Promi SD205 user can setup the serial port parameters by dip switch without PC N Security The FHSS Frequency Hopping Spread Spectrum technique of Bluetooth lets Promi SD have less radio interference and no danger of hacking in air Promi SD also supports authentication and data encryption N Benefits e No cable installation Free from the environmental limitations Easy relocation Simple maintenance Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 1 Getting Started 8 Components Promi SD101 SD202 SD205 DC 5V Power Cable Fig 1 1 Components of Promi SD Please check the components of Promi SD in Fig 1 1 when purchasing The picture of product may differ by models The components of the package may change for
15. the serial port settings of SD1 These settings must be same as those of the host system to which SD1 is used Click Next then Status Promi SD101 202 or Standby Promi SD205 LED will be lit in red Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations Promi SD Wizard Step 2 of 9 Please check and press NEXT button Cancel Click Next with marking in the check box SD1 becomes in Scan mode in which SD1 can be discovered and connected from other Bluetooth device Status Promi SD101 202 or Standby Promi SD205 LED will blink twice in green every 3 seconds Take SD2 out of the host computer Be careful to keep the power on Now plug SD2 into the serial port of the host computer and power on Promi SD Wizard Step 3 of 9 1 Make sure Status LED of Promi SDOlis blinking in Green color Leave the Promi SD01 blinking and take it Promi SD1 out from this computer Make sure power is being supplied to the Promi SDO1 2 Now connect Promi SD02 to this computer and supply power thereto Press the button below for WIZARD SETTING to be Prami SD2 identical with Promi SD02 Wizard Setting Click Wizard Setting button to configure the serial settings of SD2 These settings must be same as those of the host system to which SD2 is used Click Next then Status Promi SD101 202 or Standby Promi SD205 LED will be lit in red Promi SD Wizard S
16. tool like paper clip longer than 1 second Reset works only when power is on Configuration Software Configuration Software Usage Operating Platform PromiWizard Automatic connection of a pair of Promi SD s MS Windows 98SE or higher PromiWIN Individual setup of Promi SD MS Windows 98SE or higher This configuration software comes with the product which also can be downloaded from http www sena com PromiWizard PromiWizard is a Wizard program for the configuration of a pair of Promi SD s to make automatic connection between them afterwards To make connection with Bluetooth devices other than Promi SD use PromiWIN or AT commands on a terminal program For convenience sake we call two Promi SD s SD1 and SD2 respectively Install and run PromiWizard Promi SD Wizard Step 1 of 9 Please prepare 2E4 of Promi SDs to get paired 1st unit Promi SD01 2nd unit Promi SDO2 Connect Promi SD01 to this computer supplying power Promi SDO1 thereto UART setting of this WIZARD should be identical with 2 the UART of Promi SDO01 Press the button below for WIZARD SETTING x Default UART of Promi SD des 9600bps NonParity 1StopBit Wizard Setting Cancel Plug SD1 into the serial port of host computer and power on Status Promi SD101 202 or Standby Promi SD205 LED will be lit in red It may be blinking in green if SD1 has different settings from factory defaults Click Wizard Setting button to configure
17. unless hardware reset is executed The value of S register can be accessed and changed with ATS command by user Some S registers not shown below are set to maximize the performance of Promi SD Thus it is not recommended to change these S registers Change the value of S register only in Standby status N S1 Force to Reconnect default 1 1 0 Promi SD in Model does not try reconnection when disconnected S1 1 Promi SD in Model keeps trying reconnection when disconnected N 3 Stream UART Policy default 0 S3 0 the priority of UART streaming is throughput S3 1 the priority is latency which minimizes the delay of data transmission This is useful in case of transmiting very small data quickly N S4 Enable Remote Name Query default 1 S4 0 Promi SD inquires only BD address This speeds up the inquiry process S4 1 Promi SD inquire BD address device name and class of device N S10 Enable SD Response default 1 S10 0 Promi SD does not send SD responses to host system S10 1 Promi SD send SD responses to host system N 11 Enable Escape default 1 11 0 Promi SD does not allow escape sequence character The operation status of Connect cannot be changed to Standby As Promi SD skips the process detecting escape sequence character the more efficient data transmission is expected 11 1 Promi SD allow escape sequence character Whenever it is needed the Connect status can be changed to Standby N 12 Clea
18. 2 Cable RS232 Cable Includes LAN Cable LAN Cable Mounting Kit Mounting Kit cD cD Bluetooth USB Adapter Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Products Accessories Antenna 1A60 800 1A60 801 1A60 802 1A60 820 Stub 30mm Dipole 120mm Patch 130 90 x 65mm Board type 18 6 x 7mm ESD01 use only Power EPA UPA DPA Supply i 1A70 840 1A70 841 1A70 860 1A70 861 External Power Adaptor External Power Adaptor USB power cable DC power cable Domestic use only International use Extension RFC EEC SPC Cable a 1A80 880 1A80 881 1A80 882 Antenna extension cable 1m Antenna extension cable 15cm Serial power cable Power adapter ESD01 use only For more information and Technical Support please contact Sena Technologies Inc 210 Yangjae dong Seocho gu Seoul 137 130 Korea Tel 82 2 573 5422 Fax 82 2 573 7710 E Mail support sena com Website http www sena com Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Table of Contents Table of Contents Before Using the Product Welcome GE 3 Copyrights Certification Limited Liability 3 Precautions and Safety General Terms and Conditions of Sale 4 1 Getting Started Features of Promi SD GE 7 Components Assembly Locating the Controls Geen 9
19. All rights reserved Promi SD User Manual 2 Configurations 12 Operation Modes In addition to the serial port configurations such as bit second data bit parity stop bit flow control Promi SD has some configurations for Bluetooth For getting the most out of Promi SD user should understand the following Bluetooth connection schemes A Bluetooth device can play a role as a master or slave Master tries to connect itself to other Bluetooth device and slave is waiting to be connected from other Bluetooth devices A Bluetooth connection is always made by a pair of master and slave A slave can be in two modes Inquiry Scan or Page Scan mode Inquiry Scan mode is waiting the packet of inquiry from other Bluetooth devices and Page Scan mode is waiting the packet of connection from other Bluetooth devices Every Bluetooth device has its unique address called BD Bluetooth Device address which is composed of 12 hexa decimal numbers Promi SD has 4 operation modes as follows Each mode can be identified with LED indicators as illustrated in next section N Mode Promi SD must be in Mode when it is directly controlled by AT command s In this mode there is no response when power on or software reset and Promi SD is just waiting for AT command input Neither master nor slave is assigned to Promi SD in modeO User can change the configurations of Promi SD in this mode The factory default is set to Mode0 N Model Promi SD tries to
20. CE CE FCC FCC FOC ow oe 27x27 18x20x11 7 62 5x31 2x16 3 62 5x31 2x16 3 62 5x31 2x16 3 Stub Antenna Stub Antenna Stub Antenna Stub Antenna Includes Antenna Cable DC power cable DC power cable DC power cable 15cm AC DC power adapter Develop Board Set ESD01 or ESD02 use only DBS Jig Board Power Adaptor RS232 Cable Part Number IP30 500 Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Products Promi MSP Series Wireless Multi Serial Adapter MSP102A DPapec Pre MSP102B Part Number IP20 400 IP20 401 Wireless multi serial adapter Wireless multi serial adapter Description COM port redirector supported Serial IP COM port redirector supported Serial IP Up to 7 links simultaneously Up to 14 links simultaneously Power Class Class1 Class1 RF Range Up to 100m Up to 100m Power Connector DC plug DC plug Power supply 5V 5V Serial connector Male DB9 Male DB9 Serial Interface RS 232 RS 232 Dip switch No No Battery No No LAN Access LAN Access Profile Dial up Dial up Serial Port Profile Serial Port Profile Stub Antenna Stub Antenna Applicable Antenna Dipole Antenna Dipole Antenna Patch Antenna Patch Antenna Bluetooth Qualified Fully Fully MIC MIC Type Approved CE CE FCC FCC Dimensions Hx Wx D 147x112x32 147x112x32 Dipole Antenna Dipole Antenna AC DC Power Adapter AC DC Power Adapter RS23
21. OR THE LIKE WHETHER DIRECT OR INDIRECT IN NATURE OR FOR ANY OTHER FORM OF INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND SELLER S MAXIMUM CUMULATIVE LIABILITY RELATIVE TO ALL OTHER CLAIMS AND LIABILITIES INCLUDING OBLIGATIONS UNDER ANY INDEMNITY WHETHER OR NOT INSURED WILL NOT EXCEED THE COST OF THE PRODUCT S GIVING RISE TO THE CLAIM OR LIABILITY SELLER DISCLAIMS ALL LIABILITY RELATIVE TO GRATUITOUS INFORMATION OR ASSISTANCE PROVIDED BY BUT NOT REQUIRED OF SELLER HEREUNDER ANY ACTION AGAINST SELLER MUST BE BROUGHT WITHIN EIGHTEEN 18 MONTHS AFTER THE CAUSE OF ACTION ACCRUES THESE DISCLAIMERS AND LIMITATIONS OF LIABILITY WILL APPLY REGARDLESS OF ANY OTHER CONTRARY PROVISION HEREOF AND REGARDLESS OF THE FORM OF ACTION WHETHER IN CONTRACT TORT INCLUDING NEGLIGENCE AND STRICT LIABILITY OR OTHERWISE AND FURTHER WILL EXTEND TO THE BENEFIT OF SELLER S VENDORS APPOINTED DISTRIBUTORS AND OTHER AUTHORIZED RESELLERS AS THIRD PARTY BENEFICIARIES EACH PROVISION HEREOF WHICH PROVIDES FOR A LIMITATION OF LIABILITY DISCLAIMER OF WARRANTY OR CONDITION OR EXCLUSION OF DAMAGES IS SEVERABLE AND INDEPENDENT OF ANY OTHER PROVISION AND IS TO BE ENFORCED AS SUCH 4 INTELLECTUAL PROPERTY INDEMNITY Except as excluded herein Seller will defend any suit or proceeding brought against Buyer arising out of a claim that the design or construction of the Products sold or licensed hereunder by Seller infringes any patent copyright or trademark granted or registe
22. Promi SD can detect an abnormal disconnection But when the communication is suspended for some environmental reasons it may be regarded as disconnection N 46 BD Address of Last Connected Device This saves the BD address of the Bluetooth device connected most recently Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix C Technical Support C 1 Appendix C Technical Support UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix C Technical Support C 2 Use this form to request technical support for Promi SD Individual form should be filled out for each Promi SD in question Referring to the example on separate sheet please provide as much information as possible so we may resolve and respond to your inquiry promptly When you have finished submit this form by e mail to support sena com or by fax to 82 2 573 7710 NOTE Before you contact technical support please have a look at our FAQ Chances are you will find an instant answer to your problem v indicates a required field N User Contact Information Name Company E mail v Phone vi Fax v N Overall Hardware Setup Vv Depict or describe actual hardware connections N Host Device to which Promi SD is attached Description v Serial Port Port Parity v Setup Baud Rate Stop Bits y Data Bits
23. TION Cancellation by Buyer restocking charges including reimbursement for direct Buyer s specification may equal the actual selling price entitled to cancellation and restocking charges as iden prior to shipment is permitted only by written notice and upon payment to Seller of reasonable cancellation and costs Cancellation charges associated with orders for custom Products or Products specifically manufactured to of the Products Seller has the right to cancel an order for cause at any time by written notice and Seller will be ified above No termination by Buyer for cause will be e ffective unless and until Seller has failed to correct such alleged cause within forty five 45 days after receipt of Buyer s written notice specifying such cause 13 FORCE MAJEURE Seller will not be liable for any loss damage or delay arising out of its failure or that of its subcontractors to perform hereunder due to causes beyond its reasonable control including without limitation acts of God acts or omissions of Buyer acts of civil or military authority fires strikes floods epidemics quarantine restrictions war riots acts of terrorism delays in transportation or transportation embargoes In the event of such delay Seller s performance date s will be extended for such length of time as may be reasonably necessary to compensate for the delay 14 DISPUTES The parties will attempt in good faith promptly to resolve any dispute arising hereunder by n
24. USER MANUAL Version 2 0 0 2006 02 24 Promi SD 101 202 205 Bluetooth RS232C Serial Adapter Promi SD User Manual Products Promi SD ESD Series ESD02 SD101 SD202 SD205 Bluetooth Serial Adapter i a Part Number 1P11 320 1P11 321 1P10 300 1P10 301 IP10 302 Board type wireless serial adapter with Board type wireless serial adapter with on External type wireless serial adapter with External type wireless serial adapter External type wireless serial adapter with dip Description MMCX antenna board antenna internal battery switch connector Power Class Class1 Class2 Class2 Classi Classi RF Range Up to 100m Up to 30m Up to 30m Up to 100m Up to 100m Power d Connector Header 2 54m Header 2 54m DC plug or 9 pin DC plug or 9 pin DC plug or 9 pin Power supply 3 3V 3 3V 5V 5V 12V 5V 12V Serial SCN Header eege Female DB9 Female DB9 Female DB9 connector 2x6 1x4x2 Serial Interface UART UART RS 232 RS 232 RS 232 Dip switch No No No No Yes 4 slots Battery No No Yes No No Profile Serial Port Profile Serial Port Profile Serial Port Profile Serial Port Profile Serial Port Profile x Stub Antenna Stub Antenna Stub Antenna Stub Antenna SC Se le Dipole Antenna Dipole Antenna Dipole Antenna Dipole Antenna Patch Antenna Patch Antenna Patch Antenna Patch Antenna Bluetooth Qualified Fully Fully Fully Fully Fully TELEC TELEC Type FCC FCC MIC MIC MIC Approved CE CE CE
25. actured refurbished or reconditioned at Seller s discretion Buyer requested onsite warranty service consisting of time travel and expenses related to such ser vices will be at Buyer s expense The foregoing will be the exclusive remedies for any breach of warranty or breach of contract arising therefrom i General Warranty satisfaction is available only if a Seller is provided prompt written notice of the warranty claim and b Seller s examination discloses that any alleged defect has not been caused by misuse neglect improper installation operation maintenance repair alteration or modification by other than Seller accident or unusual deterioration or degradation of the Products or parts thereof due to physical environment or electrical or electro magnetic noise environment j THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRAN TIES AND CONDITIONS WHETHER EXPRESSED IMPLIED OR STATUTORY INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PERFORMANCE OR APPLICATION WARRANTIES TO THE FULLEST EXTENT PERMITTED BY APPLI CABLE LAW Rights under the above warranties subject to noted limitations extend to Buyer s customers if Buyer is a Seller appointed distributor for the Products 3 DISCLAIMER AND LIMITATION OF LIABILITY TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW SELLER WILL NOT BE LIABLE FOR ANY BUSINESS INTERRUPTION OR LOSS OF PROFIT REVENUE MATERIALS ANTICIPATED SAVINGS DATA CONTRACT GOODWILL
26. ation specified requested or controlled by Buyer or any third parties or c the use of the Products in combination with other Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Before Using the Product equipment software or materials not supplied by Seller As used in this paragraph the term Products shall mean only Seller s standard hardware and software that are generdly commercially available and expressly excludes third party branded equipment software THIS PARAGRAPH IS IN LIEU OF ALL WARRANTIES OR REPRESENTATIONS WHETHER EXPRESS OR IMPLIED THAT THE PRODUCTS WILL BE FREE OF THE RIGHTFUL CLAIM OF ANY THIRD PARTY BY WAY OF INFRINGEMENT OR THE LIKE 5 RESALE OF THIRD PARTY BRANDED PRODUCTS AND SERVICES NOTWITHSTANDING ANY OTHER PROVISION HEREIN SELLER MAKES NO REPRESENTATIONS PROVIDES NO INDEMNITIES INTELLECTUAL PROPERTY OR OTHERWISE AND DISCLAIMS ALL WARRANTIES OF ANY KIND EXPRESS OR IMPLIED RELATIVE TO ANY THIRD PARTY BRANDED PRODUCT OR SERVICE INCLUDING TRAINING WHICH MAY BE RESOLD OR SUBLICENSED BY SELLER AS A DISCRETE ITEM HEREUNDER 6 LICENSED SOFTWARE AND FIRMWARE Use of Products comprised of software or firmware may be subject to Buyer s acceptance of additional terms and conditions set forth in separate Seller or third party license agreements that will control to the extent necessary to resolve any conflict with the terms and conditions stated or otherwise referenced here
27. bsidiaries or affiliates as part of a consolidation merger or any other form of corporate reorganization 17 LANGUAGE The parties acknowledge that they have required that the agreement evidenced hereby be drawn up in English Les parties reconnaissent avoir exig la r daction en anglais du Contrat In the event of a conflict between the English and other language versions the English version will prevail Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 1 Getting Started 6 1 Getting Started Features of Promi SD Components Assembly Locating the Controls UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 1 Getting Started 7 Features of Promi SD N Reliability and Interoperability Promi SD is a terminal device for wireless serial communication using the Bluetooth technology that is international standard of short range wireless communications Promt SD accomplishes more reliable wireless communication As Promi SD can communicate with other Bluetooth devices user may construct various communications with it Promi SD provides several models with different communication ranges from 30m Promi SD101 up to 100m Promi SD202 205 for user s various applications In terms of noise Promi SD delivers better quality of communication than standard RS232 cables N Compact Design Promi SD has the most compact design of the
28. ct the technical support N Hardware Flow Control Promi SD plugged into its host system transmits data from host to the other side Bluetooth device These data is saved temporarily in the internal buffer of Promi SD and sent repeatedly until the transmission is completed packet by packet When the radio transmission condition is not good enough to send data prompily it can cause the transmission delay If the host sends more data when the buffer is full buffer overflow will make Promi SD malfunction consequently In order to prevent this buffer overflow Promi SD works as follows Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 14 In case of using hardware flow control Promi SD makes RTS be disable to stop receiving further data from the host when the buffer becomes full RTS will be able to begin receiving data again from the host when the buffer has some room for more data In case of not using hardware flow control Promi SD clears the buffer to secure the room for next data when the buffer becomes full This means the loss of data As the transmission data becomes large the possibility of data loss goes higher For large data transmission use of hardware flow control is highly recommended Reset to Factory Defaults To turn back all the configurations to its factory settings press the reset button depicted in Fig 1 3 Press the reset button with a narrow pointed
29. cts like in Mode2 but allows any connection from other Bluetooth device Most of general Bluetooth device is set to Modes Promi SD in Mode3 can be discovered and connected from any other Bluetooth devices Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations LED Indicators N Promi SD101 SD202 Indicator Power LED Status LED ModeO Green Red Model Green gt Green every sec ri Mode Green Green every 3 sec 1 Mode3 Green m Green every 3 sec Connected Green Green m N Promi SD205 Indicator Power LED Standby LED Connect LED Moche Green Red _ Model Green Green every 1 sec Fi Mode2 Green Green every 3sec rz Mode3 Green r n Green every 3 sec rr Connected Green Green m RS232 Tx and RS232 Rx LED are blinking accordingly when data is transmitted For small data transmission it may be hard to recognize the quick blinking Serial Ports The applicable settings for serial ports a re as follows Serial Port Settings Values Baud rate Data bit Parity Stop bit Hardware Flow Control 1200 2400 4800 8 1 2 Use No use 9600 19200 38400 57600 115200 230400 No parity Even parity Odd parity The values in box are the factory defau N Data Bit ts Promi SD supports only 8 data bit In the case of 7 data bit please conta
30. d Flow Control Comments N Promi SD Model Name v BD Address S Register v BD Address is the 6 digit number labeled on the product As for S Register the values are shown by AT amp V command on a PC running Serial Port program e g HyperTerminal See the User s Manual for details Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix C Technical Support N Pin Assignment to Promi SD Promi SD Direction Signal Pin Out CD 1 Out TxD 2 In RxD 3 In DSR 4 GND 5 Out DTR 6 In CTS 7 Out RTS 8 In Vcc 9 N Bluetooth Connection This Promi SD is connected to mark one lt gt lt gt lt gt lt gt lt gt lt gt lt gt lt gt lt gt C 3 Host Device Pin Signal Direction O an another Promi SD O a Promi ESD O a Promi MSP O others Model v Manufacture Application S W N Environment for RE Communication Distance v Obstacles v N Problems you have Distance is a linear distance between Promi SD and the other side Bluetooth device Obstacles are things affecting RF performance in the middle of Promi SD and the other side Bluetooth device such as walls partitions other equipments etc Copyright 2006 Sena Technologies Inc All rights reserved
31. dard having DB female interface 5 4 3 2 1 ET 9 8 7 6 Pin Signal Direction Description 1 CD Output Received Line Signal Detect 2 TxD Output Transmitted Data 3 RxD Input Received Data 4 DSR Input DTE Ready 5 GND S Signal Ground 6 DTR Output DCE Ready 7 CTS Input Clear to Send 8 RTS Output Request to Send 9 Vcc Input Ring Indicator Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 3 Connections Pin Assignment N To Host with DTE Interface DTE Host System DCE Promi SD 1 CD 1 Status 2 RxD 2 TxD 3 RxD 4 DSR 5 GND 6 DTR 7 CTS 8 RTS 9 Vec N To Host with DCE Interface DCE Host System DCE Promi SD 1 CD 1 Status 2 TxD 2 TxD 3 RxD 3 RxD 4 DSR 4 DSR 5 GND 5 GND 6 DTR 6 DTR 7 CTS 7 CTS Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 3 Connections 26 Power Supply Promi SD can be supplied power through the power jack and through pin 9 of DB connector N Through Power Jack DC 5 12V Min 150mA power should be supplied through DC power cable Red cable is positive and black one is negative Electrical Polarity 6 we DC Power Cable A KE AC DC power adaptor and USB power cable are also available to supply power USB Power Cable NS Through Pin 9 of DB9 connector The power can be supplied through pin 9 of DB connector Because Promi SD does not ha
32. dem at each end for signal translation While simple in concept the many opportunities for data error that occur when transmitting data through an analog channel require a relatively complex design It was thought that a standard was needed first to ensure reliable communication and second to enable the interconnection of equipment produced by different manufacturers thereby fostering the benefits of mass production and competition From these ideas the RS232 standard was born It specified signal voltages signal timing signal function a protocol for information exchange and mechanical connectors Refer the following site for detail s http www camiresearch com Data_Com_Basics RS232_standard html N DTE DCE If the full EIA232 standard is implemented as defined the equipment at the far end of the connection is named the DTE device Data Terminal Equipment usually a computer or terminal has a male DB connector Equipment at the near end of the connection the telephone line interface is named the DCE device Data Circuit terminating Equipment usually a modem has a female DB9 connector The cable linking DTE and DCE devices is a parallel straight through cable with no cross overs or self connects in the connector hoods If all devices exactly followed this standard alll cables would be identical and there would be no chance that an incorrectly wired cable could be used N DB Female Promi SD is a DCE device compatible with RS232 stan
33. egotiations between representatives of the parties who have authority to settle the dispute If unsuccessful the parties further will attempt in good faith to settle the dispute by non binding third party mediation with mediator fees and expenses apportioned equally to each side Any dispute not so resolved by negotiation or mediation may then be submitted to a court of competent jurisdiction in accordance with the terms hereof These procedures are the exclusive procedures for the resolution of all such disputes between the parties 15 GOVERNING LAW AND FORUM The agreement evidenced hereby and all disputes arising thereunder will be governed by and interpreted in accordance with the internal laws and will be subject to the exclusive jurisdiction of the courts of the state province or other governmental jurisdiction in which Seller s principal place of business resides but specifically excluding the provisions of the 1980 UN Convention on Contracts for the International Sales of Goods Should any term or provision hereof be held wholly or partly invalid or unenforceable under applicable law the remainder of the agreement evidenced hereby will not be affected thereby 16 ASSIGNMENT The agreement evidenced hereby may not be assigned by either party without the written consent of the other which consent will not be unreasonably withheld However consent will not be required for internal transfers and assignments as between Seller and its parent company su
34. encounters until receiving next character is an escape sequence character by default which is changeable by AT SETESC Reference AT SETESC ATO AT BTCANCEL 11 AT SETESC nne SD Response OK Purpose Change the escape sequence character Parameters nn Decimal number of ASCII code Default 43 Description Escape sequence character set to by default is changeable The parameter nn must be a printable character Reference ATO Example AT SETESC 42 12 ATO SD Response None Purpose Convert the operation status of Standby to Connect Description You can convert the operation status of Standby to Connect ready to transmit data Reference AT SETESC Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands 13 AT BTCANCEL SD Response WOK Purpose Terminate a current executing task Description This terminates a current executing task such as Inquiry scan and Page scan then converts the operation status to Standby Reference AT BTSCAN ATD AT BTINQ 14 AT BTSCANe SD Response WOK CONNECT 112233445566 Purpose Wait for inquiry and connection from other Bluetooth devices Description This allows the inquiry and connection from the other Bluetooth devices The operation status will be in Pending after this c
35. er Specifications Compatibility Seller does not warrant and will not be liable for any design materials construction criteria or goods furnished or specified by Buyer including that sourced from other manufacturers or vendors specified by Buyer Any warranty applicable to such Buyerspecified items will be limited solely to the warranty if any extended by the original manufacturer or vendor directly or indirectly to Buyer Seller does not warrant the compatibility of its Products with the goods of other manufacturers or Buyer s application except to the extent expressly represented in Seller s published specifications or written quotation g Recyclable Materials In keeping with environmental policies and practices Seller reserves the right to utilize in its product manufacturing repair and remanufacturing processes certain recyclable materials e g fasteners plastics and the like or remanufactured parts equivalent to new in performance or parts which may have been subject to incidental use However such utilization will not affect any provided Product warranty or published reliability statistics h Remedies Remedies under the above warranties will be limited at Seller s option to the replacement repair re performance or modification of or issuance of a credit for the purchase price of the Products involved and where applicable only after the return of such Products pursuant to Seller s instructions Replacement Products may be new remanuf
36. ers try to change these S registers SD response is ERROR For details of S register refer Appendix B Reference AT amp V Example ATS10 0 Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands A 12 Command Validity AT Command Operation Status Standby Pending Connect AT O O O O ATZ AT amp F AT BIINQ2 ATD 112233445566 ATD AT BISCAN AT BTISCAN n to 6160106010 001 0 AT BISCAN 1 12233445566 to AT BTCANCEL O O AT SETESC ATO ATH AT BTSEC Auth Encr AT BILAST2 AT BTMODE n AT BTINAME Name AT BTKEY nnnn AT BTINFO AT BTLPM n AT BISD AT BTCSD AT BTFP n 6160 0160 010160100068 680 AT UARTCONFIG b p s h SD101 202 AT UARTCONFIG b p s SD205 AT USEDIP Only SD205 O O Valid only when Promi SD is not connected to other Bluetooth device Valid only when Promi SD is connected to other Bluetooth device Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix B S Register B 1 Appendix B S Register cet UNWIRED it s easy Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix B S Register B 2 S Register S registers contain 46 parameters of Promi SD These are stored in flash memory and sustained the values
37. esentatives are available for work and waiting whether on or off the job site to perform the services 10 CHANGES AND SUBSTITUTIONS Buyer requested order changes including those affecting the identity scope and delivery of the Products must be documented in writing and are subject to Seller s prior approval and adjustments in price scheduling and other affected terms and conditions In any event Seller reserves the right to reject any change that it deems unsafe technically inadvisable or inconsistent with established engineering or quality guidelines and standards or incompatible with Seller s design or manufacturing capabilities Seller further reserves the right to substitute using the latest superseding revision or series or equivalent Product having comparable fom fit and function 11 RETURNS All returns of Products will be pursuan return policies in effect at the time including applicable o Seller s instructions Non warranty returns of unused and resalable Products for credit will be subject to Seller s restocking charges and other conditions of return Products returned under warranty must be properly packed and shipped to Seller specified locations Shipping containers must be clearly marked per Seller s instruction and shipped freight prepaid by Buyer Notwithstanding the foregoing all sales of Open Box Products and any third party branded products are final and do not qualify for non warranty return 12 ORDER CANCELLA
38. evice Name PSDy3b 16213F Device Hardware Address 00085316213F Current Mode MODEO ZB Current Status Standby Device Setting Security Security Dont use Encryption Dont use Connection out Uart Setting Baud Rate z 9600 Hi StopBit d One Stopbit Connectiontin Parity S No Parity HAN Flow control Use Serial port settings can be changed by lt Start Configuration gt and lt PromiWIN Configuration gt of PromiWIN in the menu bar at upper left corner of the window without re running the PromiWIN program The icons in the left side windo w come to the corresponding windows In device configuration window hardware reset can be executed or operation mode and RS232 can be configured as well Security option also can be configured in this window Serial port was open COM 1 9600 No Parity One Stopbit PromiWiN Hard Reset Return Promi SD to factory default setting r Operation Mode MODED Standby status for Bluetooth connection C MODE1 This Promi SD shall connect to the last connected device only C MODE2 This Promi SD shall be connected from the last connected device only MODES Allow any Bluetooth devices discover connect to this Promi SD You must be in Pending status in MODES to be discoverable connectable To be in Pending status please click MODE3 and press Apply button Connection out Uart a j Device Name PSDvab 16213F iHi Parity None z Security Option AT Command Connection in StopBi
39. he last connected device Description The Bluetooth device connected to this Promi SD last time is displayed with its BD address Reference AT BTSCAN ATD AT BTINFO AT BTINQ2 Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands 9 AT BTMODE ne SD Response BOK Purpose Set operation mode Parameters n 0 MODEO Default n 1 MODE n 2 MODE2 n 3 MODE3 Description When the operation status is Pending currently change the status to Standby with AT BTCANCEL prior to this command To take effect of this command ATZ or power off and on Reference AT BTINFOZ Example AT BTMODE 2 WKF ATZ 10 SD Response OK Purpose Convert the operation status of Connect to Standby Description In Connect status data from host is transmitted to the other side Bluetooth device and any AT command is not accepted but this command which is not echoed on the screen When Promi SD encounters a character from host it stops the data transmission and waits for next 2 characters If the next 2 characters aren t both it restart to transmit data including the first as well If not it converts the operation status to Standby If the data from host includes it will convert the operation status to Standby unexpectedly Notice that Promi SD holds data transmission when it
40. improving product capacity or quality without notice Assembly xX Antenna is left hand threaded x Use of non authorized power adapter is not recommended Fig 1 2 Assembly of Promi SD Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 1 Getting Started Locating the Controls Front Panel Back Label Power Switch Reset Button X SD101 SD202 has reset button on side SD205 has it on front Fig 1 3 Locating the Controls N Front Panel t H Promi SD101 SD202 INITIUM Power Promi D101 Bluetooth Serial Adaptor Status Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 1 Getting Started e Promi SD205 Baud Rate E Handshake e INITIUM N Back Label it Ho LA Pairing Promi SD205 Bluetooth Serial Adaptor mi Power m Standby m Connect me RS232 Tx RS232 Rx f SD205 version 3 b Model name amp firmware version 1 6A B E D gt Product serial number 2005 04 Manufacturing year month 4 Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 11 2 Configurations Operation Modes LED Indicators Serial Ports Reset to Factory Defaults PromiWizard PromiWIN Terminal Program Dip Switch Pairing Button UNWIRED Copyright 2006 Sena Technologies Inc
41. in In the absence of a separate Seller s license agreement Buyer is granted a non exclusive non transferable license to use provided Seller s software or firmware only in object code form and solely in conjunction with Seller provided Products with no rights to sublicense disclose disassemble decompile reverse engineer or otherwise modify the software or firmware 7 PACKING AND MARKING Buyerspecified packing or marking may be subject to additional charges not otherwise included in the price of the Products 8 WEIGHTS AND DIMENSIONS Published or advertised weights and dimensions are estimates or approximations only and are not warranted 9 PRICES Prices and other information shown in any Seller publication including product catalogs and brochures are subject to change without notice and to confirmation by specific quotation Such publications are not offers to sell and are maintained only as a source of general information Prices do not include sales use excise customs value added or similar taxes Buyer will pay or reimburse Seller for all such taxes as may be applicable Time and material services will be provided in accordance with Seller s published service rates including applicable overtime and travel expenses in effect as of the date such services are provided unless otherwise confirmed by Seller s written quotation or order acknowledgment Billable service time includes travel time to and from the job site and all time Seller s repr
42. l Before Using the Product 3 Welcome Thank you for purchasing Promi SD products Promi SD is a terminal device for wireless serial communication using Bluetooth technology the international standard for short range wireless communications Its interoperability and credibility delivers the maximum benefits of wireless communication This user manual is designed to help you use the Promi SD series properly It is important that you read the manual to ensure that you get the most out of your products Thank you Copyrights Certification Limited Liability N Copyrights INITIUM Co Ltd has all the rights of the patent trademark literary property and intellectual property related to this manual You may not copy or reproduce any part of this manual unless authorized by INITIUM Co Ltd You can be punished by using any part of this manual illegally The companies institutions products people and events used in examples are not real data We don t have any intension to be related with any companies institutions products people and events through this manual and should not draw inferences Users are responsible for observing the copyrights and intellectual properties Certification Promi MIC Bluetooth CE FCC TELEC SD101 O O O O O SD202 O O O O O SD205 O O O Limited Liability Neither the manufacturer importers nor dealers is responsible for any accidental damage including bodily injury or any damage resulting f
43. nect LED blinks 3 times every 2 seconds Now press again the Pairing Button for 2 seconds until Connect LED blinks every 0 5 second Wait for SD1 amp SD2 to be connected for a while until Connect LED s of SD1 and SD2 is lit in green It takes about 30 seconds to make a connection If there are many Bluetooth devices nearby it will take a little bit more Turn SD1 off and on Connect LED blinks twice in green every 3 seconds Turn SD2 off and on Connect LED blinks once in green every 1 second Now a pair of Promi SD205 is configured to make automatic connection whenever power off and on Just use this pair of Promi SD205 like virtual serial cable Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 3 Connections 23 3 Connections RS232 Interface Pin Assignment Power Supply UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 3 Connections 24 RS232C Interface x RS232C In the early 1960s a standards committee today known as the Electronic Industries Association developed a common interface standard for data communications equipment At that time data communications was thought to mean digital data exchange between a centrally located mainframe computer and a remote computer terminal or possibly between two terminals without a computer involved These devices were linked by telephone voice lines and consequently required a mo
44. ning ASCII Code a Carriage return Ox0D v Line feed Ox0A 7 Carriage return Line feed 112233445566 Bluetooth device address norm One digit decimal number to Timeout in second Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands A 3 Command Category Command Category Index AT commands RESET 1 ATZ 2 AT amp F SERIAL PORT 3 AT 4 AT UARTCONFIG b p s h SD101 202 AT UARTCONFIG b p s SD205 5 AT USEDIP BLUETOOTH Information 6 AT BTINFOZ 7 AT BTINQ 8 AT BTLAST Mode 9 AT BTMODE n Status 10 11 AT SETESC nn 12 ATO 13 AT BTCANCEL 14 AT BISCAN 15 AT BISCAN n to 16 AT BTSCAN 1 12233445566 to Connection 17 ATD 18 ATD112233445566 19 ATH Security 20 AT BIKEY string 21 AT BTSD2 22 AT BTCSD 23 AT BTFP n 24 AT BTSEC a e Miscellaneous 25 AT BTNAME string 26 AT BTLPM n S REGISTER 27 AT amp V 28 ATSnn 29 ATSnn mm Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands Command Description 1 ATZ SD Response DKS Purpose Software Reset Description This is the same effect as power off and on This command disconnects Bluetooth device and stops ongoing task After rebooting the status is decided by the preset operation mode Some AT commands need ATZ to take effect Reference AT amp F AT BTCSD AT UARTCOMFIG 2 AT amp
45. o use Promi SD does not support RS 232 break signal x Pin Assignment Promi SD is DCE device If your host equipment is DTE plug Promi SD directly to the host equipment or use straight RS 232 cable If your host equipment is DCE use cross over RS 232 cable Null modem cable Data Loss or Malfunctioning N Hardware Flow Control When transmitting large data with No use of Hardware Flow Control Promi SD will clear the data buffer unexpectedly This possibility goes higher as the RF transmission environment is bad N SD Response The messages of SD response may affect the function of host system Set ATS10 0 not to send SD response to host system and try again Refer Appendix B for details Transmission Delay NS RE Processing Delay fakes 30msec approximately for a Promi SD to complete the data transmission to the other side Bluetooth device This time delay cannot be reduced and would be bigger as the RF transmission environment is bad Do not use Promi SD If your applications cannot allow this time delay N RF Transmission Environment If there are lots of Bluetooth device working in a small area and or the RF communication distance is too long and or there are some obstacles affecting RF performance Promi SD repeats the transmission packet by packet due to interferences and or low RF performance This leads the transmission time delay Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual
46. ommand When connection is made and released the operation status is back to Pending To convert the operation status to Standby AT BTCANCEL must be used This has the same effect as AT BTSCAN 3 0 When connection is made with other Bluetooth device SD response will be CONNECT with its BD address Reference ATD AT BTINQ AT BTCANCEL 15 AT BTSCAN n to SD Response WOK CONNECT 112233445566 or WOK RROR amp Purpose Wait for inquiry and connection from other Bluetooth devices for a given duration Parameters n 1 Allows Inquiry scan n 2 Allows Page scan n 3 Allows both of Inquiry scan and Page scan to Time duration in seconds Description For the given to Promi SD is waiting for the inquiry and connection from other Bluetooth devices If the parameter of to is 0 it will wait forever When connection is made with other Bluetooth device SD response will be CONNECT with its BD address If there is no connection made within this time duration SD response is ERROR and the operation status becomes to Standby Reference ATD AT BTINQ2 AT BTCANCEL Example AT BTSCAN 2 30 16 AT BTSCAN112233445566 to SD Response WOK CONNECT 112233445566 or WOK RROR amp Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands
47. or requisition that are in addition to or otherwise not consistent with the terms and conditions set forth or referenced herein This product is produced by INITIUM Co Ltd 2 WARRANTY a Hardware Seller warrants that new hardware Products furnished here under will be free from defects in material workmanship and design for a period of one 1 year from the date of invoice from Seller or its appointed distributor as the case may be Repaired or replacement Products provided as a result of this warranty subparagraph ae similarly warranted for a period of six 6 months from the date of shipment to Buyer or the remainder of the original warranty term for that particular Product whichever is longer b Software and Firmware Unless otherwise provided in a Seller or third party license Seller warrants that standard software or firmware Products furnished hereunder when used with Sellerspecified hardware will perform in accordance with published specifications prepared approved and issued by Seller for a period of one 1 year from the date of invoice from Seller or its appointed distributor as the case may be Seller makes no representation or warranty express or implied that the operation of the software or firmware Products will be uninterrupted or error free or that the functions contained therein will meet or satisfy Buyer s intended use or requirements c Non Warranty Factory Remanufacture Repair and Field Exchange Seller warrants that non war
48. r Data Buffer When Disconnected default 0 12 0 Promi SD does not clear the data buffer received from host system when disconnected 12 1 Promi SD clears the data buffer when disconnected N S14 Enable DTR Transfer default 1 SD202 205 only 14 0 DTR DSR signal is transferred to loop back S14 1 DTR signal is transferred to DSR of remote device N 15 Enable Disconnect by DTR default 0 SD202 205 only 15 0 DTR signal cannot release the connection 15 1 The connection can be released when DIR signal is off N S24 Maximum Number of Inquiry Result default 10 The maximum number of inquiry list can be controlled Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix B S Register B 3 N 28 Escape Sequence Character default 43 The decimal number of the ASCII code of escape sequence character can be controlled The initial value is 43 the ASCIl code of N 29 Error Code The most recent error code is stored in this register User cannot change this value X 31 Page Timeout default 300 This is the timeout in seconds to attempt connection with ATD command N 33 Inquiry Timeout default 30 This is the timeout in seconds to execute inquiry scan N 37 Supervision Timeout default 16000 This is the timeout in 625usec to presume disconnection which is set to 16000 initially 16000x 625usec 10sec The smaller the value becomes the more quickly
49. ranty factory remanufactured or field exchanged hardware Products or repaired hardware Product components will be free from defects in material and workmanship for a period of one 1 year from the date of invoice from Seller or its appointed distributor as the case may be Repaired or replacement Products provided as a result of this warranty subparagraph are warranted for a period of thirty 30 days from the date of shipment to Buyer or the remainder of the original warranty term whichever is longer d Services Seller warrants that Products comprised solely of services e g training on site repair engineering and custom application programming services will be performed by appropriately skilled personnel employed or retained by Seller e Open Box Products Seller warrants that hardware Products sold as Open Box e g customer and distributor returns factory refurbished or reconditioned etc will be free from defects in material and workmanship for a period of ninety 90 days from the date of invoice from Seller or its appointed distributor as the case may be Open Box Products while serviceable may not reflect the latest series or revision Repaired or replacement Products provided as a result of this warranty subparagraph are similarly warranted for a period of thirty 30 days from the date of shipment to Buyer or the remainder of the original ninety day warranty term for that particular Product whichever is longer f Buy
50. red in the country of Seller s shipping destination provided a Buyer promptly notifies Seller in writing of any such claim and any suit or proceeding b at Seller s expense Buyer gives Seller the sole tight to defend settle and control the defense of the suit or proceeding c Buyer provides all necessary information and assistance for such defense or settlement and d Buyer takes no position adverse to Seller in connection with such claim In the event Seller is obligated to defend such suit or proceeding Seller will pay all costs and damages finally awarded or agreed upon by Seller that are directly related thereto Seller s obligations under this paragraph will be fulfilled if Seller at its option and expense i procures for Buyer the right to continue using such Products ii replaces the same with non infringing equipment software having functionality similar to that of the Products iii modifies the Products to make them nor infringing while retaining similar functionality or iv if i iii are not commercially practicable refunds to Buyer the purchase price of the affected Products in exchange for their return Seller will have no obligation to defend or for any other liability with respect to a any suit or proceeding to the extent based on or arising out of a configuration or modification made specified or requested by Buyer and which is incorporated into or constitutes the Products b the use of the Products in a process or applic
51. ries gt communication gt HyperTerminal Select the Serial port that Promi SD will be connected to Input the same settings into Serial port configuration window as Promi SD settings The settings need to be set correctly otherwise error message may be shown up on the screen or cause malfunctioning of Promi SD Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 21 HIE 2 B GIOIE HI E D MHCIEN P SA HES SS MOE Choose the settings in File gt Properties gt Settings gt ASCIl setup that let you turn echo on in HyperTerminal this will show the response Promi SD sends on the screen You now get the HyperTerminal window where you are able to control Promi SD with AT commands For expanded AT commands that Promi SD provides please refer to Appendix A AT commanas Example of AT commands AT BTINFO 000B53000509 PSDv2a 000509 MODEO STANDBY 0 0 HWFC OK AT BTINQ 000B5320007E PSDv2a 20007E 001F00 0004B300E205 AP2002 1 0 020300 OK ATD000B53000509 OK CONNECT 000B53000509 Dip Switch Promi SD205 only This feature is only on Promi SD205 With the combination of 4 slot dip switches baud rate and hardware flow control can be set simply without host computer Reset Button Dip Switch Pairing Button Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 22 Upper
52. rom misuse or unsuitable operation by you The information on this manual is prepared with the current product specifications The manufacturer Sena Technologies Inc is adding new features to the product and may persistently apply new technologies hereafter All standards may be changed at any time without notice Precautions and Safety N Electricity Use only the supplied AC adapter Use of unauthorized power adapter is not recommended Electrical shock may result e Do not kink or crease the power cable or place heavy objects on the power cable Fire can result from damaged power cables Do not handle power plug and adapter with wet hands Electrical shock may result e Immediately power off the product and unplug the AC adapter if smoke or odors emit from the product and adapter Fire can result from improper use Immediately power off the product and unplug the AC adapter if water or other liquids are present Fire can result from improper use N Product Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Before Using the Product 4 e Promi SD meets the RS 232 standards Do not wire with non standard products Damage to your products may result from improper use e Do not drop or subject the device to impact Damage to your products may result from improper use Keep away from harsh environments including humid dusty and smoky areas Damage to your products may result from improper use
53. s of Promi SD The table below shows the average measuring results in different operation modes with 1m communication distance Operation Status SES SD202 Not plugged into Serial port 17MmA Plugged into Serial port 31mA Inquiry Scan 106mA Page Scan 106mA Inquiry amp Page Scan 64mA Connected as Master device 60mA Connected as Slave device 37MA Connected in Park mode as Master device 33mA Connected in Park mode as Slave device 32mA Connected and Transmitting Data at 9600bps mA Connected and Transmitting Data at 115200bps 80mA The power consumption will be increased as the communication distance is getting longer but never exceeds 106 mA in any case N Wireless Coverage The table below shows the average measuring results in open space These results can vary according to the environmental conditions Antennas for two Promi SD units Maximum Distance Maximum Distance SD202 205 SD101 Stub Antenna Stub Antenna 100m 30m Stub Antenna Dipole Antenna 150m 50m Dipole Antenna Dipole Antenna 200m 80m Patch Antenna Dipole Antenna 400m 150m Patch Antenna Patch Antenna 1 000m 300m N Battery SD101 only e Type Lithium lon e Capacity 3 8V 190mAh e Protector Temperature and current voltage protection e Charging Time 1 Hour 45 Minutes 15Minutes e FulHoad Runtime 5Hours when transmitting data at 115200kbps Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User
54. sponse OK Purpose Change device name Parameters string New device name Default PSDv3b 445566 Description Promi SD can have a user friendly name to identify easily The name allows 30 alpha numeric characters maximum Reference AT BTINFO2 AT BTINQ2 Example AT BTNAME My Promi SD 26 AT BTLPM mi SD Response KZ Purpose Set low power mode Parameters n 0 Inactivate Default n 1 Activate Description During no data transmission Promi SD can be in low power mode to save the power consumption It takes a few seconds to wake up Promi SD in low power mode 27 AT amp V SD Response 0 mO S1iml Sn mnz KY Purpose Display all the S register Description All parameters are stored at S egister in flash memory These values are sustained until hardware reset Reference ATS 28 ATS nn SD Response walue z KY Purpose Display a given S register Parameters nn Address of S register Description A specific S register is displayed Reference AT amp V 29 ATSnn mme SD Response BOK Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual Appendix A AT Commands A 11 Purpose Change S register value Parameters nn Address of S egister mm New value of S register Description Some S egisters are optimized for the overall performance and protected from an arbitrary change by user When us
55. t a IF Authentication Encryption ON I HAW Flow Control Password C OFF Apply Promi SD has 4 response messages OK ERROR CONNECT and DISCONNECT In some cases these responses can affect the host system unexpectedly To prevent this user can set the response to ON or OFF For Promi SD205 hardware flow control can be configured only by dip switch Thus H W Flow Control option will not work in this case Click Apply button to reflect the given options to Promi SD actually Connect icon will show the following window to search and connect other Bluetooth devices Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 20 Serial port was open COM 1 S600 No Parity One Stopbit PromiWiN i 7 Search Result Information Device Address Device Name Promi MSP_200268 B 3 00081B00514C HWJEON LAPTOP 000 00082420056E Promi MSP_20056E 020300 Device Setting Connection out PITT TT B s 10 Define the number of nearby devices to be searched Connection in 000853200268 Connect to Specified devices i Drop the Connection Click Search button to search nearby Bluetooth devices The maximum number of devices to be searched can be controlled Select one of the devices searched and click Connect button The selected Bluetooth device must be in Page scan mode Click 424 al di button to cancel the connection normally Connection
56. tep 4 of 9 Please check and press NEXT button Cancel Click Next with marking in the check box Status Promi SD101 202 or Standby Promi SD205 LED will blink in green SD2 begins to search nearby Bluetooth devices for 30 seconds The program will show the Bluetooth devices with Device Address Device Name and CoD Class of Device Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 16 Promi SD Wizard Step 5 of 9 To stop to search press Cancel Search Please select Promi SDO1 by its BD address in the list below and press CONNECT button Device Address Device Name 00081600514C HWJEON LAPTOP 00010C 0006 2420056E UNKNOWN 020300 O000F0901234 oH LIZ 3G 720204 OUE SEE NES MSP NOD Search 000853200258 Connect Cancel Connecting S Connecting to target device Promi SD Wizard Step 6 of 9 Successful Connection Status LEDs of both Promi SD01 and Promi SD02 are in Green color not blinking It takes about 5 seconds to complete connection SD1 and SD2 now have each other s BD address Status Promi D101 202 or Standby Promi SD205 LED s of both SD1 and SD2 will be lit in green For the automatic connection between SD1 and SD2 when power off and on operation mode of SD1 and SD2 have to be set respectively Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 2 Configurations 17 Promi SD Wi
57. ve any protection circuit from surge it must be constant voltage of 5 12V Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 4 Trouble Shooting 27 4 Trouble Shooting No Data Transmission Data Loss or Malfunctioning Transmission Delay UNWIRED Copyright 2006 Sena Technologies Inc All rights reserved Promi SD User Manual 4 Trouble Shooting 28 No Data Transmission N COM Port Settings Check whether the Baud rate of Promi SD is same as that of its host equipment If you do not know the current Baud rate of Promi SD initialize it to 9600 by pressing Reset Button Check whether the Data bit is set to 8 Promi SD supports only 8 Data bit If your host equipment uses 7 Data bit and even or odd parity it can work as if it uses 8 Data bit and No parity This is valid only when both DCE devices are Promi SD In this case set both Promi SDs to 8 Data bit and No parity If one of DCE devices is other Bluetooth device such as Bluetooth USB dongle please contact Technical Support Check whether the Parity and Stop bit of Promi SD are same as those of its host equipment Promi SD supports No parity Even parity and Odd parity 1 and 2 Stop bit Check whether the host equipment of Promi SD uses Hardware Flow Control Promi SD is initially set to Use of Hardware Flow Control If your host equipment does not use Hardware Flow Control set the Hardware Flow Control of Promi SD to N
58. zard Step 7 of 9 Now WIZARD will configure Auto connection mode Two Promi SDs in this mode will be connected automatically whenever powered Configure UART of Promi SD02 for my use Baud Rate 9600 X Parity None EN Stopbit fi DN a Don t use Hardware Flow control Change UART as above and set up Promi SD02 to go Auto connection mode Cancel Set the operation mode of SD2 to Model SD2 is working as a master trying to connect itself to SD1 Promi SD Wizard Step 8 of 9 Jobs for Promi SD02 is finished Take it out and connect Promi SDO1 to this computer Configure UART of Promi SD01 for my use Baud Rate 9600 e Parity None gt Stopbit fi EN F Don t use Hardware Flow control EE UART as above and set up Promi SD01 to go Auto connection mode Cancel Take SD2 out of the host computer and plug SD1 into the serial port again Set the operation mode of SD1 to Mode2 SD1 is working as a slave waiting for the connection from SD2 Promi SD Wizard Step 9 of 9 Auto connection mode has been successfully configured Now Promi 5001 and Promi SD02 are paired and will be connected always even after repowered Please switch off both Promi SDs and switch them on at the same time then both units will be connected automatically Cancel Now the configuration of SD1 and SD2 has been completed When power off and on both of them they will make connection again automatically
Download Pdf Manuals
Related Search
Related Contents
入 札 仕 様 書 西病棟用医療機器 魚沼市立小出病院 2015年10月 説明会配布資料 Springerlink - Training Kit Service Manual - Fuji Electric 取付・取扱説明書 立水栓ユニット フォギータイプA otra LG Electronics MT-50PZ40, MT-50PZ41, MT-50PZ43S, MZ-50PZ42, MZ Aveo EU, v.7 (rev 3), fr-FR (Work nr: K692C_50) Copyright © All rights reserved.
Failed to retrieve file