UHBX HDBaseT HDMI extender with PoH , RS232, IR
Contents
1. 500 ft using a single Cat6 cable Receiver type determines the max distance that can be 70m 100m or 150m A second single gang module can be added to the wall plate to provide RS 232 and IR extension in both directions The RS 232 can operate at any baud rate including 115 200 at all times and the IR extension is fully compatible with all standards SONY NEC RCS SHARP RCA etc The wall plate is powered though the Cat6 cable eliminating the need for a separate power supply connection The wall plate conforms to HDBaseT power standard PoH or IEEE802 3af making it compatible with any certified HDBaseT power sourcing equipment The wall plate sender may be connected to projectors or TVs that have direct HDBaseT inputs In this case no external receiver would be needed A POH inserter will be required Hall Research part number 511 POH 17W 2 0 Features e Extends HDMI or DVI video up to 500 ft on just one Cat6 e RS232 and IR extension in both directions with optional add on e Supports all HDMI or DVI resolutions including 4K UHD e Wall plate does not need power connection powered via UTP e Power over HDBaseT PoH meets IEEE 802 3af standard e Sturdy and compact metal construction e Fully compatible with HDBaseT standard e Includes Mud Ring for easy installation no electrical box needed e RS232 supports baud rates to 115K e IR extension meets all standards regardless of format or frequency e Fully isolates ground betw2. interpret the status being indicated Make sure the cable length does not exceed the capability of the remote Receiver UH 1BT can go a max distance of 70m 229 ft UH 1BTX is capable of 100 meters 330 ft and the UHBX R PSE has a mode switch for 100 meter or 150 meter see Receiver User Manual Make sure the display is compatible with the video source by connecting them directly Make sure that you are using good quality UTP or STP cables particularly if the cable distance is approaching the max specifications Never use low skew cable for digital video extension low skew cables are suited for analog video extension but do not work well for digital video We recommend 23 Gauge Cat6 cable and if the length is close to the specified maximum distance augmented Cat6 is recommended The extender requires that the source DDC signals of its HDMI output operate at100 KHz or less and support clock stretching The vast majority of sources meet these requirements But if you determine that a particular source does not by substituting a video pattern generator or a different source a Hall Research model EMX HD AUD is recommended to resolve source incompatibility issues If you still are not able to get the system working properly contact Hall Research support preferably via email or the form on support page of www hallresearch com with a detailed description of the issue and the troubleshooting steps you have taken Do not ope
3. the display but may not be able to send power to the wall plate So to connect the Wall plate transmitter to the display the 511 POH 17W inserter can be utilized 511 POH 17W PoH Inject Pe Projector with UHBX S WP 115 230 v AC HDBaseT input The inserter has a universal AC input and can be connected to 115 230v AC The package includes the following e Power supply module e North American Power cord customer must provide their own AC input cables when used with other standards e 6 ft UTP Cable The inserter can be connected at either end but it is recommended to locate it at the remote end of the HDBaseT extension as shown above HDMI Extension on UTP 7 0 Installation When using UHBX R PSE receiver please refer to its User Manual UMA1215 for details on that device including configuration of the Long Reach mode or details on IR and RS 232 extension 7 1 Mounting the Transmitter and Heat Dissipation The UHBX S WP comes with a single gang mud ring When used in conjunction with the UHCOM WP add on a two gang mud ring is supplied It is recommended to use the mud rings for installation The mud ring has no back so the unit s rear is not sealed and allows for better heat dissipation If for some reason you have to use an electrical box make sure to use a metal box with open the holes to allow airflow Never use a plastic box as it restricts airflow and insulates the device causing excessive heat build up t
4. HALL USER S MANUAL RESEARCH ag MALI HDMI Video Extender Wall Plate Transmitter with Optional IR and RS232 Add on Send HDMI Video up to 500 ft 150 m using a single Cat6 cable CHDBT Model numbers covered in this User s Manual Individual Transmitters UHBX S WP HDMI on Cat6 HDBaseT Wall Plate Transmitter UHCOM WP RS232 IR Add on Wall Plate for UHBX S WP Kits UHBX WP P2 HDMI on Cat6 HDBaseT Wall Plate Transmitter and PSE Receiver UHBX WPC P2 HDMI RS232 IR Wall Plate Transmitter and PSE Receiver Accessories 511 POH 17W PoH Compliant Power Inserter with Universal AC Input UMA1224 Rev n c SE RS RS ll Copyright 2013 Hall Research Inc All rights reserved 1163 Warner Ave Tustin CA 92780 Ph 714 641 6607 Fax 714 641 6698 HDMI Extension on UTP Table of Contents 1 0 Introduction 2 0 Features 3 0 Model numbers covered in this User s Manual 4 0 UHBX S WP Wall plate Transmitter 4 1 Compatible Receivers 4 2 Connection Block Diagrams 5 0 UHCOM WP RS232 IR Accessory for UHBX S WP 5 1 Connecting to UHBX S WP 5 2 Connection Block Diagram 6 0 Model 511 POH 17W PoH Compliant Power Inserter 7 0 Installation 7 1 Mounting the Transmitter and Heat Dissipation 7 1 LED indicators 8 0 Troubleshooting O o0 o JUADA ant A A WD Ww 9 0 Specifications TRADEMARKS USED IN THIS MANUAL Hall Research and its logo luad are trademarks of Hall Research Any other trademarks mentioned in
5. een TX and RX sides e Locking HDMI input connector e Made in USA HDMI Extension on UTP 3 0 Model numbers covered in this User s Manual Individual Transmitters UHBX S WP HDMI on Cat6 HDBaseT Wall Plate Transmitter UHCOM WP RS232 IR Add on Wall Plate for UHBX S WP Kits UHBX WP P2 HDMI on Cat6 HDBaseT Wall Plate Transmitter and PSE Receiver UHBX WPC P2 HDMI RS232 IR Wall Plate Transmitter and PSE Receiver Accessories 511 POH 17W PoH Compliant Power Inserter with universal AC input 4 0 UHBX S WP Wall plate Transmitter The UHBX S WP is an HDMI on Cat6 HDBaseT single gang wall plate Transmitter The package includes the following e UHBX S WP Decora metal insert e Standard white plastic Decora face plate e Mud ring for dry wall installation lt GR VIDEO UNK ee i INPUT wp i fen 4 1 Compatible Receivers The wall plate sender is compatible with any HDBaseT receiver that complies with PoH or IEEE 802 3af and can source power PSE such as Hall Research Model UHBX R PSE The UHBX R PSE receiver supplies power to the wall plate and also features Long Reach mode allowing extension to 150 m approx 500 ft This combination is of UHBX S WP wall plate sender and UHBX R PSE receiver can be purchased as a kit that includes both The kit part number is UHBX WP P2 UHBX Wall Plates The wall plate can also be used with the lower cost UH 1 BTX R ma
6. hat can shorten the device s life A AT ri LL Mud ring Metal open back Metal holes punched Plastic Box The UHBX S WP dissipates approximately 2 5 watts of power so the unit will be warm to the touch this is normal the temperature is well within UL limits and the circuit components are designed to operate at these temperatures Do not install the unit in a plastic electrical box though the device will continue to operate the elevated circuit temperature may cause the unit to fail prematurely DTA The Decora units are 1 8 deep and have connectors on the back side If a wall box is to be used we recommend a wall box which has a depth of at least 2 5 inches to accommodate the connectors and cables VIDEO LINK 7 1 LED indicators 6 Link UTP Link Solid on means Sender amp Receiver are communicating Video Off No Video Blink Video without HDCP ON Video with HDCP x UHBX Wall Plates 8 0 Troubleshooting If you are experiencing problems getting the extender to work properly please use the following troubleshooting suggestions Make sure that all of the connections on both the sender and the receiver are solid Loose connections are often the cause of issues Try resetting the system by unplugging the power supply connected to the PSE side and after 5 seconds plugging it back in Check the state of the LED s on the front of both the sender and the receiver Refer to section 7 1 to
7. n or try to repair the unit yourself as this will void your warranty To return the extender for repair you must contact HR Support at 714 641 6607 or via email or web To ship the unit back for repair make sure to obtain a Return Material Authorization RMA number oo BH HDMI Extension on UTP 9 0 Specifications Video Standards DVI single link and HDMI compliant with HDMI 1 4 video specifications including 12 bit color depth 3D video and 4K support Signal type TMDS Connectors Locking HDMI input RJ45 HDBaseT output Resolutions DVI signal VGA 640x480 thru WUXGA 1920x1200 HDTV signal 4801 through 1080p Digital Cinema 4K 4096x2160 Audio Formats All HDMI Embedded Audio including LPCM 7 1CH Dolby TrueHD and DTS HD Master Audio 32 192kHz sample rate Other Signals DDC Pass Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake CEC Pass Thru DDC for Consumer Electronics Control compatible devices RS232 Bidirectional full duplex any baud rate up to 115 200 IR Extended in both directions Carrier modulation range from 30 KHz to 60 KHz PoH Power over HDBaseT meets IEEE 802 3af standard PD side identifies as Class 2 PoE device General Power Supply 100 VAC to 240 VAC 50 60 Hz external 5 VDC 3 2 A regulated Actual DC current powering both PSE and PD sides 1 8A max Power 3 0 watts 10 BTU maximum Temp humidity Storage 40 to 158 F 40 to 70 C 10 to 90 non c
8. ondensing Operating 32 to 104 F 0 to 40 C 10 to 90 non condensing Cooling Convection Enclosure type Metal Dimensions 2 6 H x 1 3 W x 1 8 D 66mm H x 33mm W x 46mm D dimensions exclude mounting tabs on front for Decora plate Product weight Product 5 oz 0 31 Ib or 142 g Shipping 8 5 oz 0 53 Ib or 241 g includes mud ring amp faceplate Vibration ISTA 1A in carton International Safe Transit Association Compliance CE FCC Class A MTBF 90 000 hours Calculated Estimate Specifications are subject to change without notice L K WW y UHBX Wall Plates HALL RESEARCH Copyright 2013 Hall Research Inc All rights reserved
9. single gang wall plate option for UHBX S WP to add RS232 IR compatibility The package includes the following UHCOM WP Decora metal insert Standard 2 gang white plastic Decora face plate 2 gang mud ring for dry wall installation Interconnect cable for connection to UHBX S WP 5 1 Connecting to UHBX S WP As mentioned above the UHCOM WP includes a short cable for connection to the UHBX S WP Sender On the rear of both wall plates there is a small connector Plug the supplied cable to both connectors The plug and receptacles are keyed so there is only one way to plug them in HDMI gt HDMI gt RS 232 RS 232 lt gt IR Out IR In IR In IR Out This Configuration is available in kit form Kit part number UHBX WPC P2 c 6 0 Model 511 POH 17W PoH Compliant Power Inserter The 511 POH 17W is a PoH compliant power inserter that can be used to power one end of an HDBaseT link It passes the UTP signals across while at the same time injects 48v power for the PD powered device The supply complies with the IEEE 802 3af and will only apply power to the cable if a compliant device is connected wen om cam acta CSS CURE SEE ETS TS 511 POH 17W HDBT HDBT PWR For example you can use the power injector to power the UHBX S WP wall plate transmitter if the receiver does not supply power via the UTP cable Some TV s and projectors have direcct HDBaseT inputs receiver is built in to
10. this manual are acknowledged as the property of the trademark owners FCC RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been designed to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are intended to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment on Compliant ws N FC SIWWO Cc D FC 2 UHBX Wall Plates 1 0 Introduction This manual covers Hall Research s wall plate components of UHBX series of HDMI extenders The wall plate transmitters can be purchased just by themselves or as a kit that includes a compatible receiver The basic HDMI sender fits in a single gang Decora style wall plate and is capable of sending a video signal to a compatible receiver to a maximum of 150 meters
11. x distance 100 meters or the economical UH 1BT R max distance 70 meters however since these do not provide power a compatible PoH inserter is required Hall Research part number 511 POH 17W 4 2 Connection Block Diagrams Following are typical ways to configure the extension system 4 2 1 Recommended Connection Scheme The UHBX R PSE receiver is recommended for use with the HDMI wall plate sender It is a compact box with only a single 5v power supply It complies with the required PoH handshake and only injects power on to the UTP cable after detecting a compliant device on the other end The UHBX R PSE receiver also features a user settable switch for activating Long Reach mode in order to support distances in excess of 100 meters to 150 m It also provides RS 232 and IR connectors to allow adding extension of control signals see section 5 2 UHBX S WP UHBX R PSE HDMI In HDMI Out This Configuration is available in kit form Kit part number UHBX WP P2 4 2 1 Alternate Connection Scheme It is possible to use the lower cost receivers UH 1BTX R max distance 100 meters or the economical UH 1BT R max distance 70 meters however since these do not provide power a PoH inserter is required Model 511 POH 17W UHBX S WP 511 POH 17W UH 1BT R HDMI In HDMI e 2 I 0 Oo 115 230 v AC oo BH HDMI Extension on UTP 5 0 UHCOM WP RS232 IR Accessory for UHBX S WP The UHCOM WP is a
Download Pdf Manuals
Related Search