IR Speed Dome User`s Manual
Contents
1. Please refer to the baud rate sheet for detailed information Baud Rate 9600bps 4800bps 2400bps 1200bps 2 2 Set address dial switch nd Figure 2 3 4 49e ice 4 4 The encode mode adopts binary system 1 to 8 is valid bit The highest address bit is 255 You can refer 14 to following sheet for more information Address 1 2 3 4 5 6 7 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 254 OFF ON ON ON ON ON ON ON 255 ON ON ON ON ON ON ON ON 15 3 Cable Connection 3 1 RS485 and Power Cable Connection There are three cable groups power cable RS 485 cable and video cable They are used to transmit video signal control signal and power connection Please connect the power cable to the power socket of the speed dome connect the RS485 cable to the RS485 port of the speed dome See Figure 3 1 and Figure 3 2 Power RS485 and Video Connection Figure 3 2 Name Function 485 A 485 A It is to control dome built in PTZ B 485 B It is to control dome built in PTZ GND Ground AUDIO OUT R2. default manual or the height has the higher priority Built in IR light night vision status it can use the IR light to spot the monitor object or you can monitor the environments in the low illumination at night Built in zoom lens high high e Auto focus e Auto iris control integrated e Auto brightness control digital e Auto white balance process e Auto day night switch Auto B W amp color switch color camera e Preset title display e View dome initial setup information e Modify camera parameter e Set preset OSD e Set auto scan e Set 7 alarm inputs and 2 alarm outputs e Set auto patter e Set auto day night switch Auto B W amp color switch e Set privacy mask zones 1 3 2 Technical Specifications 11 Power AC 24V 3A x2096 Includes temperature control circuit Camera Driver Consumption 11W IR Light Consumption s20W Decoder Built in Engine Stepper motor Preset 255 in PELCO protocol Auto Tour 8 Auto Pattern 5 Auto Scan 5 Privacy Mask Maximum 8 zones Alarm Input Output 7 2 Information Time address dome title dome coordinates temperature and etc Lens Adjust speed in accordance with lens Auto Rotation Tilt 92 auto rotates to pan 180 Auto Pan 0 360 continuously Manual Pan Motion 0 1 200 Preset Maximum 60 2409 s There are 16 You can set fr
3. 3 In this situation we recommend RS485 distributor This device can turn star type connection into the connection that conforms to RS485 bus industry standard which can avoid the above mentioned problems and enhance communication reliability See Figure 7 4 Figure 7 4 7 5 RS485 Bus FAQ Phenomenon Possible Reasons Solution Speed dome Host address baud rate and Modify host or speed dome setup can run self speed dome address baud rate e Switch RS485 positive end and diagnosis but I are not match negative end can not control Positive and negative end of Fix connection cable firmly it RS485 Bus are misconnected Replace RS485 Bus Connection cable is loose RS485 Bus connection are cut off can control RS485 Bus connection are not Connect RS 485 Bus again the speed good Replace RS485 Bus dome but is not e RS485 bus is Add terminal matching resistance smooth distance between hostand e Add RS485 distributor speed dome is too far Parallel connected too much speed domes 40 8 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Sheet Metal Plastic Parts PCB Housing Bearing Connection Cable Motor I
4. ADDR HARD ADDR SOFT BACK EXIT Move the cursor to SITE INFORMATION and then click confirm button ADDR TYPE There are two options soft and hard Please use the left right button on the keyboard or in the speed dome terminal menu to set ADDR HARD It is an address you set in the dial switch You can not modify it through software ADDR SOFT You can set address via software It is to say you can use menu to modify dome address The value ranges from 1 to 255 BACK Go back to the previous menu EXIT Log out system menu 4 4 1 3 System Time Setting Move the cursor to SYSTEM TIME SETING and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click confirm button to save current setup After you see speed dome menu displays OK you can see the setup is valid now 4 4 2 Display Setting 24 PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP OUTSIDE T amp H IDLE TIME TITLE DISP BACK EXIT Move the cursor to DISPLAY SETUP and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click save button to save current setup PRESET TITLE Display dome preset title or not Please use the left right button on the keyboard or in the speed dome terminal
5. It may result in lens damage or it may adversely affect the device performance If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 6 About Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact you local retailer ASAP if something is missing in your package 1 Features and Functions 1 1 General Introduction This series IR speed dome product is an integrated high intelligent speed dome It adopts water drop configuration design and has small and delicate shape This is a digital and intelligent product of vivid video It supports the auto IR light enable function in low illumination environments and the near and far light intelligent control The installation is convenient The IR speed dome external ports adopt the buckle device to realize the quick installation There is waterproof interface for the pipe thread All of these make the installation easier It supports various languages real time clock function and protocol auto recognition It supports 360 continuously 92 tilt and 180 auto flip It can realize no blind spot monitor This series product can be widely used in remote monitor environments such as electric power customs and water conservancy It is suitable for the m
6. Rate Max Distance 2400 BPS 1800M 4800 BPS 1200M 9600 BPS 800M In the following situations the max transmission distance shall become shorter accordingly The communication cable is a little bit thin The surrounding environment has strong electromagnetic interference There are too much devices connected to the RS485 bus And vice versa the max transmission distance shall become longer 7 3 Connection Methods and Terminal Resistance 1 RS485 bus requires all devices use the following connection methods Both terminals shall have 1200 resistance See Figure 7 1 Figure 7 1 Or you can refer to for the simplified way as in Figure 7 2 But the distance between D shall not exceed 7M Main Control Device Figure 7 2 2 Please refer to chapter 2 1 for 1200 resistance information on the main board 7 4 The Problem in Practical Use In practical usage we usually adopt star type connection The terminal resistance shall connect to the furthest two devices Such as device 1 and device 15 in Figure 7 3 But this connection way does not 39 conform to RS485 Bus standard When the distances between devices are too long the signal reflection occurs and anti jamming decreases thus the signal reliability becomes very low You can see speed dome is not under control or speed dome is running automatically and can not stop EN gt ass Ss T d Main Control Device Figure 7
7. System Information eere ee eee ee eee eese eee ee teen eate ota tn enata tasto tatnen sosta ene tn tasa enata 22 4 3 Main MON TOEIC UNCLE m 22 4 4 Men Operation eR 23 441 System Information sse eene enne eene nne innere inerenti enn nas 23 442 Display Setting niren osse ee eee e e a e RO ERR EI RO des 24 4 43 Camera Setting utter edt trie ee 25 444 F nction tete tete eite te iet e E UR P e E RH RR dee 28 4 45 Light 34 4 26 isset 35 4 5 Dome Abnormal Phenomenon 36 4 5 1 Restore to Factory Default 36 452 PTZ Movement is not 36 Ae etse dp frr 37 5 1 Daily Maintenant er 37 5 2 Problems and Esto inier fem 37 6 APPENDIX THUNDER PROOF AND SURGE 38 7 APPENDIX Il ABOUT RS485 39 7 1 RS485 Bus Main 39 7 2 RS485
8. after modifications you need to move the cursor to SAVE button and then click confirm button to get all setup activated Otherwise privacy zone may not move correspondingly with the object Please enter privacy zone menu now all the privacy zones are closed Move the cursor to PRIVACY NO please use left right key to set different privacy zones For example shift to 001 section and then move the cursor to ACTIVATE Secondly use left right key to select ON mode Now there is a privacy zone in the screen centre Thirdly use PTZ to move camera so that privacy object fit well with screen centre Fourthly move the cursor to RESIZE and then click left and right key to adjust privacy zone direction and size Fifthly move the cursor to SAVE and then click confirm button to exit 32 PRIVACY NO Here is to set privacy mask zones Please use left right button on the keyboard or in the speed dome terminal menu to set The value ranges from 1 to 8 ACTIVATE There are two settings on and off When activate function is on the privacy mask function will be activated and displays in the screen When activate function is off the privacy mask function will be closed and the blank will not displayed in the screen RESIZE It is to adjust the privacy zone size Please continue pressing direction button to widen narrow zone size lt is to narrow the horizontal width and is to widen the horizontal width 1 is to widen vert
9. have set one pattern System pops up an icon OK to prompt you system has memories one pattern RUN Here is to activate pattern Input pattern number move the cursor to RUN and click confirm button system begins running pattern STOP Here is to stop current pattern Input pattern number move the cursor to STOP and click confirm button System stops current pattern BACK Go back to previous menu EXIT Log out system menu Note The dwell time between two orders should be less than one minute otherwise system will set to default value as one minute After click PROGRAM STOP not click CALL button before icon disappears completely Any manual operation during the pattern procedure will terminate current dome pattern operation 4 4 4 6 Privacy Masking Window blank Please make sure you current camera supports this function PRIVACY ACTIVATE RESIZE DELETE SAVE BACK EXIT Move the cursor to PRIVACY ZONE and click confirm button system goes to privacy mask setup interface For SONY series cameras There are maximum 8 privacy mask zones in 360 degrees The tilt angle ranges from 0 to 70 degrees For HITACHI series cameras There are maximum 8 privacy mask zones in 360 degrees System supports two privacy zones in one screen Tilt angle ranges from 0 to 45 degrees Note For security reasons please set privacy zone little bit larger than the privacy object size Each time
10. ie tet s itn eiat pete ee e e TA Re E E eed 10 1 3 SpecIfICatiOls fesicssceusscsnsnnssosccnnssrsadensusiasendessnsuadessasadedsedensostaseadeasnauaduedasvasessedeaseniuseadessunendeadoscasetsasesiosendcassasenense 10 1 3 1 Performance 10 132 T chnical SpecifICatioris i rer ttr ttr emo rr inde eel t tee arde ue OO Qul T ep dacs eee 11 2 PROTOCOL BAUD RATE ADDRESS 13 2 1 Protocol and Baud Rate Setup eee e eee ee esee ette ense ne estne neta tasse tata sene ts tasse tata ana 13 2 2 Set address dial SWitch iere dea ean 14 3 CABLE CONNEC FION Cerda da aeu napa nhu au iva dran cente 16 3 1 RS485 and Power Cable Connection e eere eere eee ee eee rettet toe tn tenete to ette tas tee epo eene iooi toisina 16 3 2 Alarm Cable E E T m 17 3 2 1 System esee esie a e aditu ade de atit 18 322 Alarm Corninectlon eee e eie eet ee eta desees 19 3 2 8 Keyboard 19 MENU SS s 21 4 1 Screen Menu lInd x norte eterni n AE ANEAN a 21 4 2 Self diagnosis
11. or baud Power supply is not sufficient Circuit connection is too loose Please refer to user s manual for rate setup is not right detailed information Replace power socket Connect tightly Video switch or power problem Need electrical engineer help Video is not clear Focus is in manual mode Control manually Dome cover is dirty Wash dome cover During camera switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 37 6 Appendix Thunder Proof and Surge Protection This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 1500W such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible For vast land please use sealing steel tube under the land to implement cable layout and connects one point to the earth Open floor cable layout is forbidden In area of strong thunderstorm hit or near high sensitive volta
12. BLC slow shutter wide dynamic region WDR 26 o Manual becomes valid after you set the gain setting shutter iris setting wide dynamic region WDR AV It becomes valid after you set the exposure setting iris setting wide dynamic region WDR It becomes valid after you set the shutter setting exposure compensation wide dynamic region WDR GAIN SETTING The value ranges from 1 to 16 Default value is 2 Please use the left right button on the keyboard or in the speed dome terminal menu to set SHUTTER You can set shutter speed here The value ranges from 1 3 to 1 10000 Default value is 1 50 Please use the left right button on the keyboard or in the speed dome terminal menu to set IRIS SETTING The value ranges from 1 to 18 Default value is 11 Please use the left right button on the keyboard or in the speed dome terminal menu to set EXPOSURE COM The value ranges from 1 to 15 Default value is 8 Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW AE In the strong light environment you can lower the camera exposure speed to capture the image and enhance the definition The value ranges from 1 to 16 The bigger the value the higher the exposure speed Please use the left right button on the keyboard or in the speed dome terminal menu to set Please make sure your camera supports this function SLOW SHUTTER In lower illumination environment you can lower the cameras aut
13. Bus Transmission DiStAance sssssrererscscsessessssssssssssssssrersesesesscesesssesessssssesesesesesesessssseseessssseseseces 39 7 3 Connection Methods and Terminal Resistance sssssscssssscssssssssssssssssssencnesesessssssesessseacsesessesenenenenenees 39 7 4 The Problem in Practical USe ccsssssssssssssssssssssrsesesesesssssssssssnsesssscscsesesesssssssssssssssessnseseseseceeasesssesesessees 39 7 5 RS485 BUS FA cp M 40 8 APPENDIX TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS 41 Welcome Thank you for purchasing our product This user s manual is designed to be a reference tool for the operation of your system Here you can find information about this speed dome features and functions as well as a detailed menu tree Please keep it well for future reference Before installation and operation please read the following safeguards and warnings carefully Important Safeguards and Warnings Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 24V AC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair Transportation Security No
14. CK EXIT After installation please connect speed dome to power The system goes on a self diagnosis and then it pops up the above interface to show the system information If there is anything wrong during the self diagnosis system pops up error code The above interface disappears after speed dome received the first command or the display time lasts for 4 minutes ADDR Here you can view dome address information For example 001 H 1 is the address number H is hard address mode 5 is software address mode Baud rate Dome communication baud rate Parity Communication parity bit format Protocol Current communication protocol Model Dome type Temperature Current dome internal temperature Software Dome PTZ software version 4 3 Main Menu You can open the IP dome menu via control keyboard matrix or speed dome control terminal SYSTEM INFORMATION DISPLAY SETTING CAMERA SETTING FUNCTION SETTING IR LIGHT SETTING ALARM SETTING EXIT SYSTEM INFORMATION Dome self diagnosis information address information system time setup set north direction language factory default setup reboot and so on DISPLAY INFORMATION Display dome preset title azimuth display time direction dome internal temperature dome external temperature information 22 CAMERA PARAMETERS Display dome white balance setup exposure setup day night setup focus setup FUNCTION SETTING Set preset pan scan auto cr
15. E button to save current setup TASK ACTION The option here includes none tour scan preset patter Please use left right button to set PRESET The speed dome will go to the selected preset at the specified time if you select the time task as preset The value ranges from 1 to 80 SCAN The speed dome will go to the selected scan at the specified time if you select the time task as scan The value ranges from 1 to 5 TOUR The speed dome will go to the selected preset at the specified time if you select the time task as tour The value ranges from 1 to 8 PATTERN The speed dome will go to the selected pattern at the specified time if you select the time task as pattern The value ranges from 1 to 5 SAVE After you completed the above setup you need to move the cursor here and then click confirm button to save current time setup BACK Go back to the previous menu EXIT Log out the system menu IR Light Setup IR SENSITIVITY 4 1 6 SWITCH ZOOM 6 2 10 HEIGHT 5 1 10 IRLIGHT CTRL ZOOM PRI HEIGHT PRI MANUAL NEAR LIGHT 50 0 100 INTERVAL 5 FAR LIGHT 50 0 100 INTERVAL 5 IRLIGHT COMP 3 1 5 Move the cursor to highlight IR LIGHT SETTING button and then click confirm button IR SENSITIVITY Here you can enable the IR light sensitivity function 34 SWITCH ZOOM It the zoom rate of the near light and far light HEIGHT It is the speed dome installation height from the ground IRLIGHT CTRL There are three o
16. IR Speed Dome User s Manual Version 1 0 Table of Contents 1 FEATURES AND FUNCTIONS 8 1 1 General elt gore Vedi o rone mee 8 1 2 IE E 8 1 2 1 On Screen MENU REM 8 122 On Screen e EE RR ED a ean dad Bie anions e et 8 1 23 Support multiple protocols iet ette Se dice e nt duce aie deed eed 8 1 2 4 Proportional Pan and Tilt eee tette ettet e eec e eet 8 125 Preset Setup and Recall e nere re eter i recie eid Ere eO Pere eee eu don 8 1 2 6 2AUTO SCaD idet aai pde item detiene intend amie 9 1 2 7 Auto etate teet e tte te na fet Se e 9 1 2 8 Pattern x RS Bee Ee 9 1 29 Privacy Masking stehe 9 1 2 10 9 1 2 11 Action onm eae eee A A A eee ad 9 1 2 12 ti ER p o a ead tate eee n gets 9 1 2 13 oelf didgnosis seals sees le Meo Sahat NN Ad Ri 9 1 2 14 Day Night Mode B W amp Color 9 1 2 15 Auto m 9 1 2 16 Backlight Commpensation riter ete reete ee Fee Perinde 10 1 2 17 Pari Tiltarnd Zoom nee ie dite ee b OUR OE 10 1 2 18 3Di Intelligent Location 4 05 n cra e oe reo citer peer ea e qe aes 10 1 2 19 s TM m 10 1 2 20 Image Flip cei tete
17. IT ZOOM SPEED 08 DIGITAL ZOOM OFF APERTURE 09 NEXT PAGE BACK EXIT Move the cursor to CAMERA SETTING and then click confirm button you can go to the submenu WHITE BALANCE SETUP Move the cursor to current option and then click confirm button you can go to the third menu EXPOSURE SETTING Move the cursor to current option and then click confirm button you can go to the third menu 25 DAY NIGHT Set day night mode Move cursor to current option and then click confirm button you can go to the third menu There are three options auto manual off Please use the left right button on the keyboard or in the speed dome terminal menu to set FOCUS MODE There are two modes Manual Auto Please use the left right button on the keyboard or in the speed dome terminal menu to set ZOOM SPEED The zoom speed value ranges from 1 to 8 The bigger the value the faster the speed Please use the left right button on the keyboard or in the speed dome terminal menu to set DIGITAL ZOOM There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE It is to adjust the lens to achieve clear video The value ranges from 1 to 16 Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes the following options picture flip freeze function camera factory default setup camera restart P
18. TING Move the cursor to SYSTEM TIME SETTING and then click confirm button to go to the third submenu SET NORTH DIRECTION Set dome benchmark direction so that you can know the angel between the benchmark and then current location Please move the cursor to the option and then click confirm button until you see O K Now you have set north direction LANGUAGE The dome menu language There are several languages for you to select Please use the left right button on the keyboard or in the speed dome terminal menu to set PTZ AUTO STOP The PTZ stop the corresponding operation once it reaches the time you specified here The option includes close 5S 10S 15S 20S 25S 30S and etc Please use the left right button on the keyboard or in the speed dome terminal menu to set 23 FACTORY DEFAULT Restore dome factory default setup Please move cursor to the option and then click confirm button until you see O K Now you can see the IP dome begin rebooting to restore factory default setup RESTART Reboot the speed dome BACK Go back to the previous menu EXIT Log out system menu 4 4 1 1 Initialization information ADDR 001 H BAUD RATE 9600 PARITY NONE PROTOCOL PELCO D MODEL SD6663 HN TEMP 032 C SOFTWARE 1 04 3 BACK EXIT Move the cursor to INITIAL INFORMATION and then click confirm button you can see the above interface Here you can view dome basic information 4 4 1 2 Address Information ADDR TYPE
19. cans back and forth regularly a horizontal field Here you need to left and right limit and scan speed You can set 5 scanning paths 1 2 7 Auto Touring Add addresses into a routine in a desired order and then set time and stop duration for each address The dome will begin an auto touring between these addresses You can set 8 touring paths 1 2 8 Auto Pattern Memorize dome operation such as pan tilt and zoom to repeat Focus and iris are in auto mode during auto pattern For each pattern the time should be less than 60 seconds You can set 5 pattern paths 1 2 9 Privacy Masking Privacy masking is a user defined four sided area that can not be viewed by you The masking area will move with pan and tilt functions and automatically adjust in size as the lens zooms You can set 8 privacy masking zones Depends on camera type 1 2 10 IR Night Vision In the night vision status it can use the IR light to spot the monitor object or you can monitor the environments in the low illumination at night 1 2 11 Action on Alarm This series speed dome support three alarm activation operations There are 7 alarm inputs NO NC Alarms can be individually programmed to initiate an associated preset scanning or tour when received Dome will return to a previously programmed state after alarm acknowledgement or to its previous position before alarm 1 2 12 Auto Flip As long as you continue to hold the keyboard joystick in the down position th
20. e current scene will be displayed in the central window and automatically zooms All of these allow you to trace precisely 1 2 19 Idle Status When there is no available order you can use menu to set dome idle status after specified duration The idle status includes turn to specified preset or go to scan tour or pattern function 1 2 20 Image Flip You can enable image flip in the menu The flip function allows you to view continuous video 1 3 Specifications 1 3 1 Performance Specifications 10 All digital design All data are the connection board No data loss when power off occurs e Integrated design high stability e IR speed dome max support 255 presets Support 8 auto touring Each touring max has 32 presets Built in e 5 auto scan Decode e 5 auto pattern Each pattern can max support 400 commands and the interval shall be less than 60s e Built in direction indicator e RS485 BUS control e Support max 8 privacy mask zones Depends on the camera type e 7 alarm inputs and 2 alarm outputs Built in various adjustable protocols baud rate e Fine stepper driver stable performance react quickly precisely positioning e Integrated design tight structure Built in PTZ Elegant mechanical driver device Support 360 degrees continuous rotation no monitor blind spot 0 1 s rotation speed while maintain stable image e 180 degrees tilt continuous monitor Support zoom level has the higher priority
21. e dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome 1 2 13 Self diagnosis There is a self diagnosis procedure when dome boots up Tilt and vertical engine check Camera diagnostics Display dome information and diagnosis information such as address protocol baud rate type 1 2 14 Day Night Mode B W amp Color Mode System supports auto manual switch in low illumination You can specify the switch time In the auto mode and photosensitive resistance mode the camera can automatically switch the CCD level according to the light change In the manual mode it can use the menu or the button to realize the color display black and white display and schedule switch All the modes will have automatically activation operation on the IR light except the camera auto mode This function works with the IR night vision function 1 2 15 Auto Focus Auto focus allows lens to remain in focus during zoom in zoom out and motion functions to vivid image You can use FAR or NEAR button to adjust focus manually 1 2 16 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 17 Pan Tilt and Zoom Supports zoom in and zoom out during tilt and pan movement In this period focus and iris are both in auto mode to get vivid image 1 2 18 3D Intelligent Location Working with DVR just click part of th
22. e the alarm When the activation mode is NC normal close dome alarms 17 when there is high voltage Low voltage will not activate the alarm Note Dome alarm input message is ground mode Dome alarm input signal are two modes normal open and normal close 3 2 1 System Layout 3 2 1 1 BUS connection Please refer to Figure 3 5 and Figure 3 6 for BUS cable connection Output AC 24V Input 220V 110v Video Output Monitor Power Adapter Figure 3 5 5 485 Terminal resistance on Figure 3 6 Note Please use shielded twisted pair The shielded layer shall connect to GND firmly otherwise it may affect communication or video work 3 2 1 2 Star Connection Please refer to Figure 3 7 for start connection information 18 Input 5 485 Code Distributor 3 2 2 Alarm Connection Please refer to Figure 3 8 for alarm connection information Alarm Controller Figure 3 8 3 2 3 Keyboard Connection This series dome supports keyboard operation You can use keyboard to control the dome and PTZ The display and control can work simultaneously One keyboard can control maximum 255 speed domes Please refer to Figure 3 9 LJ Keyboard Figure 3 9 This IR speed dome protocol is open and supports multiple popular system platforms in today s market 19 Please contact us freely if some matrix systems do not support dome camera communication
23. eserved audio port Audio output port Right now the device does not support this function GND Reserved audio port Ground port audio Right now the device does not support this function IN Reserved audio port Audio connection port 16 Right now the device does not support this function VIDEO GND Ground port OUT Video output port Power port connection interface is shown as in Figure 3 3 Figure 3 3 Name Function AC24V 24V power port Connect to the power cable EARTH Ground port AC24V 24V power port Connect to power cable 3 2 Alarm Cable Connection Open the dome cover and take PTZ chip core out Turn the core upside down you can see the alarm port E See Figure 3 4 Name Function Alarm out 1 2 Figure 3 4 e Two alarm output channels When there is an alarm from current channel system activates relay or not e Alarm output relay default setup is NO You can use the jump cap near the power board relay to set e NO Normal open alarm output e NC Normal close alarm output GND Alarm input ground end Alarm in 1 7 e Seven alarm input channels It is to receive relay signal from the external alarm source You can go to dome menu to activate specified preset or patter e When the activation mode is NO normal open dome alarms when there is low voltage High voltage will not activat
24. f possible Power If possible Bracket If possible Accessories Note O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 41
25. ge such as near high voltage transformer substation you need to install additional high power thunder protection device or lightning rod The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 40 and earth cable cross sectional area shall below 25 2 See Figure 6 1 Video Lighting Rod Communication Liqhting Rod Power Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 40 Steel tube shield Figure 6 1 38 7 Appendix About RS485 Bus 7 1 RS485 Bus Main Feature RS485 is semi duplex communication cable of impedance 1200 max load amount is 32 effective loads including main control device and devices to be charged 7 2 RS485 Bus Transmission Distance When we take 0 56mm 24AWG twisted pair as communication cable the max transmission distance theoretically are listed below according to different baud rates Baud
26. heavy stress violent vibration or water splash are allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer Installation Do not apply power to the product before completing installation Do not put object on the product Environment This series product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc The working temperature ranges from 30 C 60 C Outdoor Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the device Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Daily Maintenance Current series product has no power button Please unplug all corresponding power cables before your begin installation or daily maintenance work Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long time Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use the volatility solvent such as the benzene or thinner or detergent with strong abradibility
27. ht button on the keyboard or in the speed dome terminal menu to set The camera will begin auto cruise when alarm occurs RELAY OUT Here is to set relay alarm mode and reset time There are several options off 15S 2 5S 18 amp 2 5S lt 1 55 1 means first relay output 5S means the relay will reset automatically in five seconds after alarm occurs 1 amp 2 5S 1 amp 2 means the first relay and the second relay work at the same time RESET DELAY Here is for you to set alarm reset time Please use the left right button on the keyboard or in the speed dome terminal menu to set 3 seconds 10 seconds 30 seconds 60 seconds 120seconds The dome will go back to previous setup after alarm acknowledgement SAVE Move the cursor to SAVE and then click confirm button to save current setup BACK Go back to previous menu 35 EXIT Log out system menu 4 5 Dome Abnormal Phenomenon Operation 4 5 1 Restore to Factory Default Setup From main menu gt SYSTEM INFORMATION move cursor to FACTORY DEFAULT and click confirm button Dome will reboot and all the setups restore to factory default setup 4 5 2 PTZ Movement is not smooth From menu to SYSTEM INFORMATION move cursor to RESTART and click confirm button This reboot will not modify all activated setup Such as preset tour and pattern 36 5 5 1 Daily Maintenance Please clean dome cover regularly to get vivid image Handle the cover with care Use water to
28. ical height and is to narrow the vertical height SAVE Here is to save user setup DELETE Here is to delete setup and restore default setting BACK Go back to previous menu EXIT Log out system menu 4 4 4 7 Idle Motion IDLE FUNC OFF IDLE TIME 010MIN IDLE ACTION PRESET PRESET NO 001 AUTO SCAN NO 001 CRUISE NO 001 PATTERN NO 001 SAVE BACK EXIT When there is no available command for specified time dome automatically goes on the previous set functions IDLE FUNCTION There are two modes ON OFF Please use left right key to set IDLE TIME System idle period The value ranges from 1 to 720 minutes Please use the left right button on the keyboard or in the speed dome terminal menu to set IDLE ACTION There are several functions you can select NONE PRESET SCAN TOURING PATTERN Please use the left right button on the keyboard or in the speed dome terminal menu to set PRESET NO Here is for you to set preset number The value ranges from 1 to 255 System goes to specified preset when idle status is on AUTO SCAN NO The value ranges from 1 to 5 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified scan when idle status is on CRUISE NO The value ranges from 1 to 8 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified touring when idle status is on PATTERN NO The va
29. lease use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 4 4 3 1 White Balance Setup WB MODE AUTO R GAIN 001 B GAIN 001 BACK EXIT Move the cursor to WHITE BALANCE MODE and then click confirm button you can go to the submenu WHITE BALANCE MODE Set white balance adjustment mode There are two modes auto manual Please use the left right button on the keyboard or in the speed dome terminal menu to set GAIN Before you set R GAIN option please note the mode shall not be auto The value ranges from 000 to 254 Please use the left right button on the keyboard or in the speed dome terminal menu to set B GAIN Before you set B GAIN option please note the mode shall not be auto The value ranges from 000 to 254 Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 4 4 3 2 Exposure Setting AE MODE GAIN SETTING SHUTTER IRIS SETTING EXPOSURE COM SLOW AE SLOW SHUTTER BLC WDR ENBALE BACK EXIT MODE Here you can set the camera exposure mode It includes auto manual AV iris priority TV shutter priority Please use the left right button on the keyboard or in the speed dome terminal menu to set o Auto It becomes valid after you set the exposure compensation backlight compensation
30. lue ranges from 1 to 5 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified pattern when idle status is on SAVE Move the cursor to SAVE and click confirm button to save current setup BACK Go back to previous menu 33 EXIT Log out system menu 4 4 4 8 Time Task TIME TASK OFF START TIME 06H 00M END TIME 10H 00M TASK ACTION SCAN PRESET 001 SCAN 001 TOUR 001 PATTERN 001 SAVE BACK EXIT TIME TASK Schedule task allows the speed dome to implement corresponding setup during the specified time There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set START TIME Here you can set the task begin time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detailed value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit start time setup and then move the cursor to the SAVE button to save current setup END TIME Here you can set the task end time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detail value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit end time setup and then move the cursor to the SAV
31. menu to set You can go to Function Setup gt Preset section to set corresponding preset value and preset title AZIMUTH DISP Display dome current coordinates or not Please use the left right button on the keyboard or in the speed dome terminal menu to set TIME DISP Display dome system time or not Please use the left right button on the keyboard or in the speed dome terminal menu to set POSITION Display the angel between the benchmark and then current location Please use the left right button on the keyboard or in the speed dome terminal menu to set ZOOM DISP Display speed dome zoom speed or not Please use the left right button on the keyboard or in the speed dome terminal menu to set INSIDE TEMPERATURE Display dome internal temperature or not There are three options C F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set OUTSIDE TEMPERATURE AND HUMIDITY Display dome external temperature and humidity There are three options C F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set IDLE TIME The option includes close 1 2 3 4 5min The system will exit the menu automatically once there is no menu operation during the time you specify here Close means always show the menu BACK Go back to the previous menu EXIT Log out system menu 4 4 8 Camera Setting WB SETTING EXPOSURE SETTING DAY NIGHT SETTING FOCUS MODE AUTO FOCUS LIM
32. o exposure time to capture the image and enhance the definition Please note for the moving object the image trail phenomenon may occur Please use the left right button on the keyboard or in the speed dome terminal menu to set BLC It is an abbreviation for back light compensation System can compensate the object in the dark light to achieve a clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set WDR ENBALE It is an abbreviation for wide dynamic region Please make sure your camera supports current function This function can adjust the video brightness when the contrast between the strong light and the dark light is too high Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 4 4 3 3 Day Night Setting Move the cursor to DAY NIGHT SETTING and then click confirm button you can go to the submenu DAY NIGHT AUTO DAY TIME 07H 00M NIGHT TIME 19H 00M SAVE BACK EXIT DAY NIGHT There are four options auto time night day Please use the left right button on the keyboard or in the speed dome terminal menu to set DAY TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to Save bu
33. om the menu Speed Manual Tilt Motion 0 19 120 5 Manual Tilt Scan 0 180 Section Control Port RS485 BUS Baud Rate 1200 2400 4800 9600 Optional PTZ Scan Accuracy 0 06 0 015 Signal Format PAL NTSC Camera mode S N Ratio gt 50dB Effective Pixel 768 H 494 V 795 596 Horizontal Resolution 480TVL 540TVL Fan Fan works continuously Humidity lt 90 Environment 30 C 60 C Outdoor 12 2 Protocol Baud Rate Address setup Before you operate you need to set protocol baud rate and address Otherwise you can not control the product 2 1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome Protocol Baud rate Address Note Please reboot the speed dome to get all the setups activated Open the lower dome the interface is shown as below See Figure 2 1 2 7777 7 Figure 2 1 5 2 TT Figure 2 2 13 Please refer to the protocol sheets for detailed information Protocol Baud rate Parity 1200 Connect to the 1200 1 2 314 5 6 7 8 Please note speed dome cans automatically recognize the DH SD PELCO D PELCO P Usually you do not need to set 1 2 3 Communication Protocol OFF OFF OFF DH SD Compatible with China industrial standard protocol ON OFF OFF PELCO D OFF ON OFF PELCO P X X X Reserved
34. onfirm button to set the cruise Please use up down button to set preset number dwell time and speed Use the left right button to go to the next cruise Click confirm button you can exit the setup After you completed the setup move the cursor to back button to go to the previous interface DELETE CRUISE Here is to delete a cruise Input cruise number in CRUISE NO and then move the cursor to DELETE cruise click confirm button to delete CALL Here is to activate cruise Input touring number in touring NO and highlight CALL click confirm button to activate touring STOP Here is to terminate touring BACK Go back to previous menu EXIT Log out system menu 4 4 4 5 Pattern PATTERN NO 001 PROGRAM START PROGRAM STOP RUN STOP BACK EXIT Pattern function can memory PTZ operation and camera focus zoom in and zoom out From the start position dome begins auto movement repeatedly This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands Move the cursor to PATTERN and click confirm button PATTERN NO Here is to set pattern number The value ranges from 1 to 5 Please click left right key to configure PROGRAM START Here is to memorize pattern starting point An icon OK pops up in screen to prompt you system begins memory pattern 31 PROGRAM STOP Here is to set pattern stop point After the movement move the cursor to PROGRAM STOP and then click confirm button Now you
35. onitor environments of low illuminations such as the village town and suburb 1 2 Features This series speed dome has the following features 1 2 1 On Screen Menu This series product menu supports multiple languages display and switch It is easy for you to view dome information and configure dome camera parameters 1 2 2 On screen Tips Here you can view Preset name and system version Software and hardware Dome system temperature Optional You can disable this function Dome address Optional You can disable this function 1 2 3 Support multiple protocols This series speed dome supports universally used protocols such as PELCO P and PELCO D You can use various devices such as matrix control keyboard and DVR and protocols to operate speed dome 1 2 4 Proportional Pan and Tilt This function keeps the image from moving too fast when there is a large amount of zoom Speed dome continually decreases or increases pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 5 Preset Setup and Recall Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the correct position This series speed dome max supports 255 presets in PELCOD and PELCOP protocols 1 2 6 Camera s
36. protocol The most direct and easy way is to use current system to process video signal and add some control keyboards to control speed dome See Figure 3 10 Matrix or multiple image Processor Keyboard Figure 3 10 20 4 4 1 Screen Menu Index Note ERR means current setup is invalid means there is submenu INITIAL INFORMATION SYSTEM ADDR INFORMATION INFORMATION EM TIME SETTING SET NORTH LANGUAGE ENGLISH PTZ AUTO STOP 15S FACTORY DEFAULT RESTART BACK EXIT DISPLAY SETTING PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP OUTSIDE T amp H IDLE TIME BACK CAMERA SETTING WB SETTING EXPOSURE SETTING DAY NIGHT SETTING S MODE DIGITAL ZOOM APERTURE NEXT PAGE FUNCTION SETTING IR LIGHT SETTING IR 502 To SWITC QOM 6 HEIGHT 57 IRLI GHT Ric ZOOM PRI HEIGHT PRI MANUAL NEAR LIGHT 50 0 100 INT L 5 FAR LIGHT 50 0 100 INTERVALS 5 IRLIGHT COMP 3 1 5 ALARM SETTING ALARM NO 01 ACTION NONE CONTACT 001 AUTO SCAN 001 CRUISE 001 RELAY OUT OF RESET DELAY AVE The above diagram illustrates the overall structure of the dome setup menu Note ERR means current setup is invalid Please make sure all the cable connections are right 4 2 Self diagnosis System Information ADDR BAUD RATE PARITY PROTOCOL MODEL TEMP SOFTWARE BA
37. ptions Zoom rate has the higher priority height has the higher priority manual NEAR LIGHT It is the medium and near light brightness FAR LIGHT It is the far light brightness IR LIGHT COMPENSATION It is the whole compensation level of the IR light 4 4 6 Alarm Setup ALARM NO 01 ACTION NONE CONTACT N O PRESET 001 AUTO SCAN 001 CRUISE 001 RELAY OUT OFFS RESET DELAY 35 SAVE BACK EXIT Move the cursor to highlight ALARM SETTING button and then click confirm button ALARM NO Here is to set alarm input Alarm input value ranges from 1 to 7 Please use the left right button on the keyboard or in the speed dome terminal menu to set ACTION Action on alarm function It includes NONE PRESET AUTO SCAN TOURING functions Please use the left right button on the keyboard or in the speed dome terminal menu to set CONTACT You can set system activation operation once alarm occurred There are two alarm signal mode normal open N O and normal closed N C Please use the left right button on the keyboard or in the speed dome terminal menu to set PRESET NO Please use the left right button on the keyboard or in the speed dome terminal menu to set The camera will turn to the specified preset to monitor after alarm occurs AUTO SCAN Please use the left right button on the keyboard or in the speed dome terminal menu to set The camera will begin auto scan after alarm occurs CRUISE Please use the left rig
38. ranges from 1 to 80 TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING Please input preset number first and then select the monitor zone Please move the cursor to setting and click confirm button The system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully added a preset Please note you need to enable display preset title function first Main menu gt display setting gt preset title Repeat the above procedures to set more presets Once you want to modify a preset you can input the preset number you want to modify and then follow the above steps to set the preset You can successfully modify a preset content CALL Here is to recall preset Move the cursor to PRESET NO and then input corresponding preset value Then move the cursor to CALL and then click confirm button to go to a preset BACK Go back to previous menu EXIT Log out system menu For PELCO protocol user please refer to the following special functions Call preset Call preset 28 or preset 95 to go to dome menu Call preset 29 or preset 99 to go to scan Call preset 24 or preset 81 to go to pattern Call preset 25 or preset 82 to go to cruise tour Call preset 30 or preset 96 to stop scan or pattern Call preset 31 or preset 83 to begin rotation Call preset 33 to enable PTZ 180 degrees rotation Call preset 34 to se
39. rrent item and then click confirm button to reboot the camera BACK Go back to previous menu EXIT Log out system menu 4 4 4 Function Setting PRESET PAN SCAN AUTO CRUISE PATTERN IDLE MOTION TIME TASK PRIVACY MASKING BACK EXIT Please go back to main menu and move the cursor to FUNCTION SETTING click confirm button You can see the above interface PRESET Move the cursor to PRESET and then click confirm button to go to the third submenu PAN Move the cursor to PAN and then click confirm button to go to the third submenu 28 SCAN Move the cursor to SCAN and then click confirm button to to the third submenu AUTO CRUISE Move the cursor to AUTO CRUISE and then click confirm button to go to the third submenu PATTERN Move the cursor to PATTERN and then click confirm button to go to the third submenu IDLE MOTION Move the cursor to IDLE MOTION and then click confirm button to go to the third submenu TIME TASK Move the cursor to TIME TASK and then click confirm button to go to the third submenu PRIVACY MASKING Move the cursor to PRIVACY MASKING and then click confirm button to go to the third submenu BACK Go back to previous menu EXIT Log out system menu 4 4 4 1 Preset Setup PRESET NO 001 TITLE PRESETOO1 SETTING CALL BACK Move the cursor to PRESET button and then click confirm button to go to set interface PRESET NO Please use left right key to modify preset number The value
40. t dome position as 0 Set preset Set preset 26 or 92 to set scan left limit Set preset 27 or 93 to set scan right limit Set preset 22 or 79 to begin record Set preset 23 or 80 to stop record 4 4 4 2 Pan PAN SPEED 160 RUN STOP BACK EXIT Move cursor to PAN button and then confirm button to go to setup interface PAN SPEED Set dome rotation speed The Value ranges from 1 to 255 Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Move the cursor to call item and then click confirm button The dome begins 360 degrees continuous rotation STOP Highlight stop item and then click confirm button The dome stops rotation BACK Go back to previous menu EXIT Log out system menu 4 4 4 3 Scan SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT SCAN SPEED 160 RUN STOP BACK EXIT Move the cursor to SCAN button and then click confirm button SCAN NO Here is to set auto scan number The value ranges from 1 to 5 Please use the left right button on the keyboard or in the speed dome terminal menu to set SET LEFT LIMIT Here is to set camera left address Click confirm button to save current setup SET RIGHT LIMIT Here is to set camera right address Click confirm button to save current setup SCAN SPEED The value ranges from 1 to 255 Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Please inp
41. tton to save current setup 27 NIGHT TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to save button to save current setup SAVE This button is for DAY TIME and NIGHT TIME setup After you set the day time or night time you need to move the cursor here and then click confirm button to save current time setup For other setups you do not need to use this button BACK Go back to previous menu EXIT Log out system menu 4 4 3 4 Next Page Move the cursor to NEXT PAGE and then click confirm button you can go to the submenu PICTURE FLIP FREEZE FUNCTION CAMERA FACTORY DEFAULT CAMERA RESTATRT BACK EXIT PICTURE FLIP This function allows you to turn the image rotation 180 degrees There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set FREEZE FUNCTION This function allows the system from one preset to another preset without showing the video during the PTZ movement There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set CAMERA FACTORY DEFAULT SETTING Move the cursor to current item and then click confirm button to restore factory default setup CAMERE RESTART Move the cursor to cu
42. uise pattern idle motion time task and privacy mask function IR LIGHT SETTING Set dome IR sensitivity switch rate reference height IR control principle medium and far light bright far light bright IR light compensation and etc ALARM SETTING Set dome alarm number action contact preset scan cruise replay out reset delay save setup and etc EXIT Log out the system menu 4 4 Menu Operation In the speed dome main menu you can use the left right button on the keyboard or in the speed dome terminal menu to configure the system menu Before setup please move the cursor to the current item you want to configure In main menu please click confirm button to go to the sub menu or use left right key to configure setup Use up down button to select back option and then click confirm button to go back to the previous menu Use up down button to select exit option and then click confirm button to log out system menu All setup here will not lose when encounter power failure 4 4 1 System Information INITIAL INFORMATION ADDR INFORMATION SYSTEM TIME SETTING SET NORTH LANGUAGE ENGLISH PTZ AUTO STOP FACTORY DEFAULT RESTART BACK EXIT INITIAL INFORMATION Move the cursor to INITIAL INFORMATION and then click confirm button to go to the third submenu ADDR INFORMATION Move the cursor to SITE INFORMATION and then click confirm button to go to the third submenu SYSTEM TIME SET
43. ut auto scan number first and then please move the cursor to RUN and click confirm button to activate auto scan function STOP Here is to terminate auto scan function BACK Go back to previous menu EXIT Log out system menu 4 4 4 4 Cruise Touring CRUISE NO 001 CRUISE SETTING DELETE CRUISE RUN STOP BACK EXIT Move the cursor to highlight CRUISE item and then click confirm button to go to set interface CRUISE NO Here is to ser tour number The value ranges from 1 to 8 Please use the left right button on the keyboard or in the speed dome terminal menu to set 30 CRUISE SETTING Move cursor to cruise setting item and then click confirm button You can see the following interface Here you can add or remove the preset and set the corresponding dwell time and call speed One cruise can max include 32 presets The preset value ranges from 0 to 200 NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 013 32 000 005 013 B DWELL Here is t set dwell time The value ranges from 3s to 255s Default value is 5 seconds Please use the left right button on the keyboard or in the speed dome terminal menu to set B SPEED The speed value ranges from 1 to 16 The default value is 13 When you move the cursor to one cruise number you can use left right button to turn the page There are 8 cruises in each page and there are total 4 pages When you move the cursor to one cruise number please click c
44. wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note The sweat from your hand may erode plating surface your nail may scrape dome cover result in blur image 5 2 Problems and Solutions SYMPTOM CAUSE SOLUTION No self diagnosis no video signal when connect dome to power Red LED is not on 24V AC does not apply to the power Or connection is Check 24V AC power is connected or properly earthed too loose Check power supply condition Power off or Transformer or check 24V transformer problem Red LED light is on 24V AC power is low Something wrong with power socket Use multimeter to check dome load Please contact retailer to replace power socket No self diagnosis There is a noise Power supply is inadequate Replace power socket Mechanical malfunction Need electrical engineer help Self diagnosis is ok No video signal Power connection is too loose connect tightly Check the circuit connection Connect again Video switch connection is wrong or improper operation Please refer to user s manual for cable connection information Self diagnosis is o k but can not operate the dome Video signal loss occurs in high speed rotation Video signal is not successive Control circuit is not properly connected check control cable connection Dome address protocol
Download Pdf Manuals
Related Search