Home
Notice
Contents
1. e Networking amp Communication 16 Port 10 100Mbps with 8 Port PoE Web Smart Ethernet Switch FNSW 1608PS User s Manual Trademarks Copyright O PLANET Technology Corp 2006 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested an
2. O K ACCESS POWER 101 O K FNSW 1668PS Uip init legin admin password FNSW 1608PS gt show management vlan The management vlan is vlan 1 FNSH 1605P5 gt Figure 4 14 Display management VLAN screen 91 4 4 2 9 Show vlan mode Display the current vlan mode of FNSW 1608PS the vlan mode display screen in Figure 4 15 appears Write EE TEST x cf UBEEDatal Bxaa Read EE_TEST x cf u8EEDatal xaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show MY HAC Address from 24c16 0x00 30 if 00 00 00 _24c16 eeprom word read EE _DHCPEN 6 gt DHCP FALSE Show MY IP Address from 24c16 192 168 080 160 Show DNS Server from 24c16 168 95 192 01 _ 4c16_eeprom_word read EE DHCPEN 086 DHCP FALSE webt_ee network dhcp flag 0x00 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER 101 O K FNSW 1608PS Uip init login admin password FNSW 1688PS gt show vlan mode Port based YLAN FNSW 1668PS gt Figure 4 15 Display VLAN mode screen 4 4 2 10 Show pvid Display the current per port pvid of FNSW 1608PS the per port pvid display screen in Figure 4 16 appears login admin password FNSH 1608P5 gt show pvid Port 1 PYID Port 2 Port 3 Port 4 Port 5 PYID Port 6 Port Port 8 Port 9 PYID Port 10 PYID Port 11 PYID Port 12 PYID Port 13 PYID Port 14 PYID Port 15 PYID Port 16 PYID FNSH 1605P5 gt
3. _ 4c16_ eeprom _word read EE_DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 0xBb Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER 101 D K FNSW 1668PS Uip init login admin password FNSW 1688PS gt set pvid Select port 1 16 1 PYID 1 16 1 FNSH 1608PS gt Figure 4 25 PVID Configuration screen 28 4 4 3 8 Set priority This command allows set priority function of FNSW 1608PS the available options are TCP IP TOS DS Priority Disable or Enable 802 1p Priority Disable or Enable Queue Service Rate 4 1 8 1 16 1 N The priority setting screen in Figure 4 26 appears Show DNS Server from 24c16 168 95 192 61 _24c16 eeprom word read EE_DHCPEN 00 DHCP FALSE webt_ee network dhcp flag x08 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER ICI O K FNSW 1608PS Uip init legin admin password FNSW 1686PS gt set priority TCP IP TOS DS Priority 1 Enabled 2 Disabled 1 802 1p Priority 1 Enabled 2 Disabled 1 Queue Service Rate 1 4 1 2 8 1 3 16 1 4 N 1 TE a Queue Service Rate o Al FNSH 1608P5 gt Figure 4 26 Priority Configuration screen 29 4 4 3 9 Set ip xxx xxx XxxX XXX Mmm mmm mmm mmm ggg ggg gg9 ggg This command allows assign IP address netmask and gateway of FNSW 1608PS the correct usage is shown as below set ip 192 168 0 1 255 255 255 0 192 168 0 254 and press lt Enter gt If the IP is successfully c
4. 5 4 appears and table 5 2 de scriptions the Port Controls objects of switch Y PLANET Friii bh Cie Port Setup ation Enabled Disabled TT F ull LOOM Half 1104 Full TOM Had ging Control Disable QRemove Tag Olnsert Tag ith Control er ith Control Disable Mapping O High Cueva Low Queue op Beta Figure 5 4 FNSW 1608PS Port Setup Web Page screen Object Description Auto Negotiation Allow disable or enable Auto negotiation of each port Speed Allow set per port run at 10 100Mbps half full speed mode Priority Tagging control Allow disable or remove or insert priority tagging on each port the available options are Disable Remove Tag Insert Tag TX Bandwidth control Allow assign per port transmit bandwidth the available options are Disable 128K 256K 512K 1M 2M 4M 8M RX Bandwidth control Allow assign per port receive bandwidth the available options are Disable 128K 256K 512K 1M 2M 4M 8M Port Priority Mapping Allow assign low queue or high queue on each port Table 5 2 Descriptions of the Port Setup screen Objects 7 5 4 VLAN Setup A Virtual LAN VLAN is a logical network grouping that limits the broadcast domain lt allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members The FNSW 1608PS supports port based VLAN function In the default configuration with VLAN disable the screen in Figure 5 5 appea
5. Blue 12345678SIDE2 6 Green 6 Orange T White Brown T WhitefBrown 8 Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 2080 A31120 000 C 58
6. dhcp flag 6x66 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER 101 O K FNSW 1688PS Uip init login admin password FNSH 1608P5 gt set trunk Port 1 2 Trunking 1jEnable 2 Disable 2 Port 13 14 15 16 Trunking 1 Enable 2 Disable 1 Port 1 2 Trunking Disable Port 13 14 15 16 Trunking Enable FNSH 1608P5 gt Figure 4 20 Trunk Configuration screen 25 4 4 3 3 Set vian n This command allows configuring sixteen port based VLAN groups of FNSW 1608P S the correct usage is shown as below Set vlan n n 1 16 to configuring sixteen port based VLAN groups of FNSW 1608PS The configuring port based VLAN groups screen in Figure 4 21 appears yan 12340967869 10 11 12 13 14 15 16 Turn On Off VLAN port Please input port number 1 16 exit press enter FNSW 1668PS gt set vlan 2 vlan 1234567809410 11 12 13 14 15 16 Turn On Off VLAN port Please input port number 1 16 exit press enter FNSW 1668PS gt set vlan 3 vlan 1234567809410 11 12 13 14 15 16 Turn On Off VLAN port Please input port number 1 16 exit press enter Figure 4 21 Port based VLAN Configuration screen 4 4 3 4 Set poe n This command allows configuring per poe port parameters of FNSW 1608PS the correct usage is shown as below Set poe n n 1 8 to configuring per poe port parameters of FNSW 1608PS The configuring per poe port parameters screen in Figure 4 22 appears and the detai
7. speed 2 2 Rear Panel The rear panel of the FNSW 1608PS indicates an AC inlet power socket which accepts input power from 100 to 240V AC 50 60Hz and 1A max And one console port at rear panel for switch management i eS 100 240V AC i PN ER i Figure 2 2 FNSW 1608PS Switch rear panel Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your FNSW 1608PS from being damaged by unregulated surge or current to the FNSW 1608PS 2 3 Hardware Installation This part describes how to install your Web Smart Ethernet Switch and make connections to the Switch Please read the following topics and perform the procedures in the order being presented To install your Switch on a desktop or shelf simply completed the following steps 2 3 1 Desktop Installation To install a Switch on a desktop or shelf simply completed the following steps Step 1 Attached the rubber feet to the recessed areas on the bottom of the Switch Step 2 Place the Switch on a desktop or shelf near an AC power source Step 3 Keep
8. 1 12726 O lena ree eee E AAE 41 IE SY STORY ION QU ON eieo sce A A A A AD A A eae 42 50 2 PaASSWOIO Y ACCES A il be 44 520 9 SAA a ed iad aa lad 45 5 6 4 AC SI iPods 47 D 00 FINNWAIC UDI cia 49 D gl cad A NO 53 O LOCO Ur AA N e eta en Ge tc onan Ca alpen ce at etter Cae tad Pes OE 55 6 SWIT GH OPERA TON td 56 A E eer ate asc EE A EAA EEE TEET E A EATE EEIE AA wanna EAE TEER EEE TETE 56 Aa o ES AEN EEE EA 56 6 3 FORWARDING PIETER dances 56 6 4 S71 ORE AND FORWARD PEATE EEE cd EEA EE E AA E EEE EN EE TE EE EA EEE 56 oO TOI GO TION danona n a a a R a a E OSEERE 56 TTROUBEESHOO TIN Gini A A A A e aa id 57 APPENDIX A NETWORKING CONNECTION Loocccccocconconcnncnnnnnnonnnnnonnnnnonnnnnonno rn n nr nr 58 A 1 SWITCH S RJ 45 PIN ASSIGNMENTS a 58 A2 RJ45 CABI F PINAS SIENME Ni a 58 1 INTRODUCTION 1 1 Checklist Check the contents of your package for following parts e FNSW 1608PS x1 e User s manual CD x1 e Quick installation guide x1 Power cord x 1 RS232 cable x1 e Rubber feet x 4 e Two rack mounting brackets with attachment screws x1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 About the Switch The FNSW 1608PS is equipped with unshielded twisted pair UTP cable ports providing dedicated 10 or 100Mbps bandw
9. 3 14 15 16 FNSW 16608PS gt show vlan 5 ia 123456789 16111215 14 15 16 FNSW 1668PS gt show vlan Figure 4 8 VLAN group status screen 4 4 2 3 Show trunk Display the current trunk group status of FNSW 1608P S the trunk group status screen in Figure 4 9 appears FNSW 1608PS Eth init done current tick 860800003 sec EEPROM Init Write EE TEST Bx2cf usSEEDatal Bxaa Read EE TEST 6x cf usEEDatal Bxaa EEPROM 24c16 found InYalid EEPROM Restore Default Value Show MY IP Address 192 168 0 100 Initial EEPROH Initial MAC Registers ACCESS POWER ICH O K ACCESS POWER ICI O K FANSW 1608PS Uip init login admin password FNSW 1608PS gt show trunk Port 1 2 Trunking Disable Port 13 14 15 16 Trunking Disable FNSW 1686PS gt Figure 4 9 Trunk group status screen 4 4 2 4 Show ip Display the current IP address netmask and gateway of FNSW 1608PS the IP subnet address information screen in Figure 4 10 appears current tick 00000003 sec EEPROH Init Write EE_TEST 6x cf usEEDatal Bxaa Read EE_TEST x cf u8EEDatal xaa EEPROM 24c16 found InYalid EEPROM ft Restore Default Yalue Show HY IP Address 192 168 60 106 Initial EEPROH Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER ICI D K FANSW 16088PS Uip init login admin password FNSW 1668PS gt show ip IP 192 168 060 166 Netmask 259 299 209 0 Ga
10. Amaia DAA Us emange Password New Password Figure 5 13 FNSW 1608PS Password change Web Page screen Y PLANET lo AA Re Cog Figure 5 14 FNSW 1608PS Re Login Web Page screen 44 FNSW 1608PS Login Please enter your Username and Pazeweord Figure 5 15 The FNSW 1608PS login Web Page screen 5 6 3 Restore System Default This section provides reset FNSW 1608PS to factory default mode after choose this function and the following screen appears in Figure 5 16 Please press OK button to take effect and the switch will reboot automatically and ask you to re login web interface with default username admin without password the screen in Figure 5 17 amp 5 18 amp 5 19 appears CD PLANET fiaik hij Bh Pn tn Welcome to PLANET FNSW 1608P5 Web Smart Manager PLANET Technology Corporation Figure 5 16 The FNSW 1608PS reset to factory default Web Page screen 45 3 PLANET 3 PLANET Figure 5 17 The FNSW 1608PS rebooting Web Page screen Figure 5 18 FNSW 1608PS Re Login Web Page screen AG FNSW 1608PS Login Please enter your Username and Pazeweord Username admin Password Figure 5 19 The FNSW 1608PS login Web Page screen 5 6 4 Reboot System This section provides reboot FNSW 1608PS after choose this function and the following screen appears in Figure 5 20 Please press OK button to take effect and the switch will reboot and ask
11. CESS POWER ICA D K ACCESS POWER ICI D K FNSW 1668PS Uip init login admin password FNSH 1608P5 gt show show port n zall show vlan n show trunk show 1p show system show poe status n show poe nl show management vlan show vlan mode show pvid show priority FNSH 1608P5 gt Figure 4 5 Show command list screen 16 This show command list contains eleven items Show port n all Please refer to chapter 4 4 2 1 Show vlan n Please refer to chapter 4 4 2 2 Show trunk Please refer to chapter 4 4 2 3 Show ip Please refer to chapter 4 4 2 4 Show system Please refer to chapter 4 4 2 5 Show poe status n Please refer to chapter 4 4 2 6 Show poe n Please refer to chapter 4 4 2 7 Show management vlan Please refer to chapter 4 4 2 8 Show vlan mode Please refer to chapter 4 4 2 9 Show pvid Please refer to chapter 4 4 2 10 Show priority Please refer to chapter 4 4 2 11 4 4 2 1 Show port n all Display the status on each port of FNSW 1608PS these two commands allows you to view the port status of the Switch and the correct usage is shown as below Show port n n 1 16 to view per port status of FNSW 1608PS The screen in Figure 4 6 appears Show port to view all port status of FNSW 1608PS The screen in Figure 4 7 appears show port nl all show vlan n show trunk show 1p show system show poe status n show poe n show management vlan show vlan mode
12. E OWT pete cena eal e e ld ae 4 E 5 VAS PEC CA TON ud ti ad nd don 5 2 HARDWARE DESCRIPTION ie 7 2 TERON PANEL a o dq lia EO ee Se ee ee 7 ANS A A A A A 7 2 9 HARDWARE INSTALA TON dd de aa 8 3 SWI CH MANAGEMEN Lo as 10 ROVER EW ea a E E EE E E Oe RSE nT ARREST AT RON IE Ree ree 10 22 MANAGEMENT METHODS crenn e e ae E S 11 32 1 Local CONS MANITO E dd 11 O22 WED Manageme M ra a E E r N E 11 3 3 ASSIGNING AN IP ADDRESS TO THE SWITCH ccccecceccecceccecceeceecuecaecaecaeeaeceecaecaecaeeaeeaeeaeeceesueseesueeaesnseaeens 11 3 4 LOGGING ON TO THE FNSW 1608PS woiscsccccccceee dinini nie aaa da 12 4 CONSOLEINTERFACE ua aid 13 AAC ONNES TE TOPE ita rate doc bed tonta ara tecno aaa ter cl era tra li El to ene ao ta 13 A A E A RR 14 AS IMAINIMEND SC EEN a a as did o tl nl e o a e atado a 14 a EERI EEA E DPE A EEE E E E O A 15 AAT General Guidelines aci 15 AAD SHOW OO a a a te tee te 16 ASS Ol CONAN o i a os o O AE TT ol ad 23 AA AFAd laU aiaeciceiostaccacadiaedsectauasdatcnaeiest E tuaedieaateate 32 aR E O PRAE ENNE EE RE NE EE EE E EN E E A ENE EE EN E AA 33 4A OOO a AR AAA AA A N E 34 A WEB MANAGEMENT ia vais 35 Sal LOGIN INTO THE SWITCH escocia oct Soot ace rro cocinada colada dect aA asi 35 A ee ene Pe Se ee A ae ee A oe Te eee 36 A ne ee Pe Oe ee ee ae ee toe ee eee ee 37 A A AA A T ee ae ee ee oe nT eee 38 LLT VLAIN SCTUNG o AAA NN 39 Seow eg 2 Us Wet El ars ad cece Ae nn eee ee eee er ry eee rs a 40 SOM PS Gee OB NL
13. E TEST Bx24cf u8EEDatal xaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show HY HAC Address from 24c16 08x00 30 4f 00 00 00 _ 24c16 eeprom word read EE_DHCPEN 60 gt DHCP FALSE Show HY IP Address from 24c16 192 168 0 100 Show DNS Serverifrom 24c16 168 95 192 01 _24c16_ eeprom_word_read EE _DHCPEN 60 DHCP FALSE webt_ee network dhcp_ flag 6x00 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER IC1 O K FNSW 16608PS Uip init login admin password FNSH 1608P5 gt logout login Figure 4 34 FNSW 1608PS Logout screen 34 5 WEB MANAGEMENT Before login the Web interface of FNSW 1608PS please setup the IP Address with local serial console port RS232 port and use this IP address to configure FNSW 1608PS through the Web interface Or modify your PC s IP domain to the same with FNSW 1608PS then use the default IP address 192 168 0 100 to remote configure FNSW 1608PS through the Web interface 5 1 Login in to the Switch To access the Web browser interface you must first enter the user name the default user name is admin without password You will see the following screen comes out on the Web browser program FNSW 1608PS Login Please enter your Username and Password Username admin Password Login Figure 5 1 The FNSW 1608PS login Web Page screen After the User name and Password is en
14. EPROM Init Write EE_TEST x cf u8EEDatal 0xaa Read EE_TEST x cf uSEEDatal Oxaa EEPROM 24c16 found InYalid EEPROM Restore Default Value Show MY IP Address 192 168 6 1686 Initial EEPROH Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER ICI D K FNSW 1608PS Uip init login admin password The factory default login username is admin without password A Notice 1 For security reason please change and memorize the new password after this first setup 2 Only accept command in lowercase letter under console interface 4 CONSOLE INTERFACE 4 1 CONNECT TO PC RS 232 serial cable Use the bundled RS 232 serial cable and attach the 9 pin female connector to the male connector on the FNSW 1608PS Plug the other side of this cable to your PC Hyper Terminal In Windows 98 2000 ME XP launch HyperTerminal create a new connection and adjust settings as below Emulation VT 100 compatible Baud per second 19200 Data bits 8 Parity None Stop bits 1 Flow Control None To gain a demo please see the Figure 4 1 COMI Properties Te x Port Settings Bits per second 119200 7 Data bits E Parity None Stop bits f Flow controk MERE Restore Defaults a A Figure 4 1 Port Settings for console interface 13 4 2 Login in Login is required to access the console interface after the self test completes successfully T
15. Figure 4 3 FNSW 1608PS Main Menu screen 4 4 Getting Started 4 4 1 General Guidelines The FNSW 1608PS allows users to configure the device via command line under console interface Please type help or 2 for all available commands in the FNSW 1608PS gt prompt The screen of available commands in Figure 4 4 ap pears and the detail description shown in table 4 1 FNSW 1688PS gt help show port nl all show vlan nl show trunk show ip show system show poe status n show poe n show management vlan show vlan mode show pvid show priority set port n set trunk set vlan n set poe n set management vlan set vlan mode set pvid sel priority sel 1p XEX XEX XXX XXX MMM MMM Mim mmm gGgg ggg ggg gag sel pass factory default reboot logout FNSW 1688PS gt Command Show port n all Show VLAN n Show trunk Show IP Show system Show PoE status n Show PoE n Show management VLAN Show VLAN mode Show PVID Show Priority Set port n Figure 4 4 FNSW 1608PS available commands screen Description Show per port or all port current status of FNSW 1608PS Show current VLAN group status of FNSW 1608PS Show current trunk group status of FNSW 1608PS Show current IP subnet address of FNSW 1608PS Show firmware version Mac address and IP address of FNSW 1608PS Show per PoE port status On or Off of FNSW 1608PS Show per PoE port disable enable status and priori
16. IEEE 802 1p QoS 2 HARDWARE DESCRIPTION This product provides two different running speeds 10Mbps 100Mbps in the same switch and automatically distinguishes the speed of incoming connection This section describes the hardware features of FNSW 1608PS For easier management and control of the Switch fa miliarize yourself with its display indicators and ports Front panel illustrations in this chapter display the unit LED indicators Before connecting any network device to the FNSW 1608PS read this chapter carefully 2 1 Front Panel The Front Panel of the FNSW 1608PS PoE Web Smart Ethernet Switch consists of 16x Auto Sensing 10 100Mbps Ethernet RJ 45 Ports The LED Indicators are also located on the front panel of the FNSW 1608PS 3 5 7 9 1 13 PoE 2 4 6 8 10 12 14 16 PLANET FNSW 1608PS da a or h E a ee o 16 Port 10 100Mbps Web Smart Switch with 8 Port PoE Injector 000000000009000 0 Q LNKACT Mocoooo D 0000000000000000 me O sso O 000000000 PoEln Use 19200 N 8 1 PWR 1 15 Figure 2 1 FNSW 1608PS Switch front panel 2 1 1 LED indicators System LED Color Function Lights to indicate that the Switch has power Per 10 100Mbps port LE Color Function Lights to indicate the port is providing 48VDC in line power 1 8 ports LNK ACT Lights to indicate the link through that port is successfully established Lights to indicate the port is running in 100Mbps
17. Jl pd pd pd pl pd pd pd pt fed fo fr fr fol pl pm Figure 4 16 Display pvid screen 22 4 4 2 11 Show priority Display the current priority status of FNSW 1608P S the priority status display screen in Figure 4 17 appears EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show MY HAC Address from 24c16 0x00 30 4f 00 00 00 _24c16_eeprom_word read EE _DHCPEN 60 gt DHCP FALSE Show HY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom_word_read EE _DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 0x00 Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER 101 D K FNSW 1668PS Uip init login admin password FNSW 1608PS gt show priority TCP IP TOS DS Priority Disabled S02 1p Priority Disabled Queue Service Rate 16 1 FNSW 1688PS gt Figure 4 17 Display priority screen 4 4 3 Set command From the main menu screen see Figure 4 3 input set and press enter The set command list screen in Figure 4 18 appears Show DNS Server from 24c16 168 95 192 01 _24c16_ eeprom _word_read EE_DHCPEN 06 DHCP FALSE webt_ee network dhcp flag 0x4b Initial HAC Registers ACCESS POWER ICO O K ACCESS POWER IC1 O K FNSW 1608PS Uip init login admin password FNSW 1608PS gt set set port n set trunk set vlan n set poe n set management vlan
18. PEN 00 gt DHCP FALSE Show MY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom word read EE_DHCPEN 68 DHCP FALSE webt_ee network dhcp flag 0x00 Initial MAC Registers ACCESS POWER ICA O K ACCESS POWER 101 O K FNSW 1668PS Uip init login admin password FNSW 1688PS gt reboot The system will restart FNSW 1608P gt Reset System Figure 4 32 Switch reboot screen Ip 1nspc reg 0x 001 Ox3f done lt FNSW 1688PS System timer init done FNSW 1688PS Eth init done current tick 660H03 sec EEPROM Init Write EE TEST 6x cf usEEDatal Bxaa Read EE_ TEST x cf usSEEDatal Bxaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show MY MAC Address from 24c16 x 0 30 if 00 00 A _ 4c16 eeprom word read EE DHCPEN 00 gt DHCP FALSE Show MY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 01 _ 24c16 eeprom_word_read EE _DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 8x06 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER IC1 O K FNSW 1608PS Uip init login Figure 4 33 Switch reboot screen 33 4 4 6 Logout This command provides logout the FNSW 1608PS the screen in Figure 4 34 appears current tick 68000003 sec EEPROM Init Write EE TEST 6x cf usEEDatal Bxaa Read E
19. age screen Description Pot ndicateportitoport8 Indicate the POE status of port 1 to port 8 Class Display the POE PD power classification Current mA List each connected device current usage Power watts List each connected device power usage Total The summary list of Current mA and Power watts Table 5 5 Descriptions of the POE Status screen Objects 53 The POE Configuration screen in Figure 5 31 appears and Table 5 6 describes the POE Configuration object of switch After setup completed please press Apply button to take effect Y PLANET irc a e Figure 5 31 FNSW 1608PS POE Configuration Web Page screen Object Description Indicate port 1 to port 8 Enable Disable Allow to disable or enable each POE port Allow to assign the POE power provision priority on each POE port the available range is 0 3 The O is highest and the 3 is lowest Table 5 6 Descriptions of the POE Configuration screen Objects 54 5 8 Logout This section allows to logout the FNSW 1608PS the screen in Figure 5 32 amp 5 33 appears Y PLANET T F Esri ij f sinr lis Figure 5 32 FNSW 1608PS Logout Web Page screen FNSW 1608PS Login Please enter your Username and Pazeword Username admin Password Figure 5 33 The FNSW 1608PS login Web Page screen 55 6 SWITCH OPERATION 6 1 Address Table The Switch is implemented with an address table This addre
20. anage the FNSW 1608PS remotely by having a remote host with web browser such as Microsoft Internet Ex plorer or Netscape Navigator Using this management method The FNSW 1608PS must have an Internet Protocol IP address accessible for the remote host 3 3 Assigning an IP Address to the Switch To manage the FNSW 1608PS remotely through the web browser with a Management Station you must assign an IP address to the FNSW 1608PS To set the IP address please use set ip XXX XXX XXX xxx mmm mmm mmm mmm g99 999 999 9gg command For example to configure the switch with the following IP settings IP Address 192 168 0 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 254 Press the following command and press lt Enter gt set ip 192 168 0 100 255 255 255 0 192 168 0 254 If the IP is successfully configured the switch will automatically restart as the following screens After reboot the Switch and power on completed you can access the web interface of FNSW 1608PS through the new IP address cds 3 4 Logging on to the FNSW 1608PS When you log on to the FNSW 1608PS console port for the first time a sign on string appears and you are prompted for a console login user name and password FNSW 1608PS System init sys init gt walt state reg x 6d Ox28 ip inspc reg 4 x 661 Bx3f done lt FNSW 1608PS System timer init done FNSW 1608PS Eth init done current tick 860003 sec E
21. appears Default is 16 1 IP Address Allow user to assign new IP address of FNSW 1608PS after setup completed Please press Apply button and switch will reboot automatically to take effect Allow user to assign new Subnet Mask of FNSW 1608PS after setup completed Please oress Apply button and switch will reboot automatically to take effect Allow user to assign new Gateway of FNSW 1608PS after setup completed Please press Apply button and switch will reboot automatically to take effect Table 5 4 Descriptions of the System Configuration screen Objects 42 Y PLANET A e e Management VLAN UCR TOS DS Priority Queue service rate lI Address Subnet Mask Figure 5 11 FNSW 1608PS Management VLAN options Web Page screen MAG Address EW Version Management VEAN TCP IP TOSIDE Priority C Enabled Disabled 302 1p Priority Queue service rale Figure 5 12 FNSW 1608PS Queue service rate options Web Page screen 43 5 6 2 Password Access Setting This section provides password change Configuration of FNSW 1608PS please input the old password in Password space and input the new password in New Password space After setup completed please press Submit button to take effect and the switch will logout automatically Please login web interface with new password the screen in Figure 5 13 4 5 14 amp 5 15 appears PLANET
22. cp flag 6x60 Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER 101 D K FNSW 1668PS Uip init login Figure 4 28 IP subnet address configuration screen 30 4 4 3 10 Set pass This command allows assign password of FNSW 1608PS The password setting screen in Figure 4 29 appears Restore Configuration from EEPROM to Device Show HY MAC Address from 24c16 0x00 30 4f 00 00 00 _ 4c16 eeprom word read EE_DHCPEN 60 gt DHCP FALSE Show MY IP Address from 24c16 192 168 0 1 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom word read EE _DHCPEN 60 DHCP FALSE webt_ ee network dhep flag 6x60 Initial MAC Registers ACCESS POWER ICA O K ACCESS POWER ICI O K FNSW 1668PS Uip init legin admin password FNSH 1608PS5 gt set pass Old Password New Password test Change password from to test successfully FNSH 1608P5 gt Figure 4 29 Password configuration screen XA Notice 1 For security reason please change and memorize the new password after this first setup 2 The maximum length is 4 characters a ee 4 4 4 Factory default This command allows rest FNSW 1608PS to factory default mode The factory default screen in Figure 4 30 amp 4 31 ap pears FNSH 1608PS System timer init done FNSH 1608P Eth init donet current tick 86806003 sec EEPROM Init Write EE_TEST x cf u8EEDatal Oxaa Rea
23. d EE_TEST x cf uBEEDatal Bxaa EEPROM 24c16 found InYalid EEPROM Restore Default Value Show HY IP Address 192 168 0 100 Initial EEPROM Initial MAC Registers ACCESS POWER ICH O K ACCESS POWER 101 O K FNSW 1608PS Uip init login admin password PASH 1608P5 gt factory default The system will restart FNSW 1608P gt Reset System Figure 4 30 Factory default screen TF33xFU check Magic Code lok FNSH_1608P5 System init sys init gt walt state reg Ux B6d Ux28 ip 1nspc reg 0x 001 Ox3f done lt FNSW 1688PS System tiner Init done FNSW 1688PS Eth init done current tick 6000000603 sec EEPROM Init Write EE_TEST 6x cf usEEDatal Bxaa Read EE_TEST 6 x cf u8EEDatal Oxaa EEPROM 24c16 found InYalid EEPROM Restore Default Value Show HY IP Address 199 168 0 100 Initial EEPROM Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER IC1 O K FNSW 1668PS Uip init login Figure 4 31 Factory default screen 30 4 4 5 Reboot This command allows reboot FNSW 1608PS the reboot screen in Figure 4 32 amp 4 33 appears EEPROM Init Write EE TEST x cf USEEDatal Bxaa Read EE_TEST 0x7cf u8EEDatal 0xaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show HY MAC Address from 24c16 0x00 30 4f 00 00 00 _ 4c16 eeprom word read EE _DHC
24. d found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 16 Port 10 100Mbps with 8 Port POE Web Smart Ethernet Switch User s Manual FOR MODEL FNSW 1608PS REVISION 1 0 FEBAUARY 2006 Part No EM_FNSW1608PSv1 2080 A31120 000 TABLE OF CONTENTS 1 INTRODUCTION oca 4 A SAA A A eT a et Re a 4 122 ABOUT TH
25. d up to maximum 4 ports with 800Mbps bandwidth POE power Disable Enable and PoE power consumption monitoring by management interface Auto MDI MDI X detection on each RJ 45 port o EMI standards comply with FCC CE class A 1 4 Specification Model Network Connector LED Display Switch architecture MAC address Switch fabric Throughput Remote power feeding Management IEEE 802 1p Port priority Port Trunk VLAN Management VLAN PoE power control Power Power consumption Temperature Humidity Dimension W x D x H EMI Standard Compliance FNSW 1608PS 16 Port RJ 45 for 10 100TX 8 Port with PoE injector function One power 1 8 port PoE in use LNK ACT 100 9 16 port LNK ACT 100 Store and forward 8K MAC address table with Auto learning function 3 2Gbps 2 38Mpps End point insert type and compatible with IEEE 802 3af Per port feeding power 15 4 Watts Console web management interfaces Allow to assign low and high priority on each port Two trunk groups with up to 4 port per trunk Port Based VLAN up to 16 groups Yes Allow to disable or enable power provision and assign priority on each PoE port AC 100 240V 50 60Hz Max 130 watts 443 BTU hr Operating 0 50 degree C Storage 40 70 degree C Operating 10 to 90 Storage 5 to 95 Non condensing 440 x 120 x 44 mm FCC Class A CE IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3x Flow control IEEE 802 3af Power over Ethernet
26. enough ventilation space between the Switch and the surrounding objects A Notice When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 4 Specification Step 4 Connect your Switch to network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports on the front of the FNSW 1608S Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc A Notice Connection to the Switch requires UTP Category 5 network cabling with RJ 45 tips For more information please see the Cabling Specification in Appendix A Step 5 Supply power to the Switch A Connect one end of the power cable to the Switch B Connect the power plug of the power cable to a standard wall outlet then power on the Switch When the Switch receives power the Power LED should remain solid Green 2 3 2 Rack Mounting To install the Switch in a 19 inch standard rack follow the instructions described below Step 1 Place your Switch on a hard flat surface with the front panel positioned towards your front side Step 2 Attach a rack mount bracket to each side of the Switch with supplied screws attached to the package Figure 2 3 shows how to attach brackets to one side of the Switch Figure 2 3 Attaching the brackets to the Switch Caution You must use the screws supplied with the mounting brackets Damage caused to the parts by
27. h its PVID i e 3 port 2 4 port 3 to 16 port 15 After the above steps port 1 to port 15 is being separated physically due to it belongs to different VLAN groups different VLAN However they all can access port 16 due to port 16 is using PVID 1 to communicate with port 1 to port 15 This configuration for VLAN 1 to VLAN 4 can be found in Figure 5 6 39 5 5 Port Trunk Setup This section allows you to disable or enable trunk function of two ports or four ports together to speed up data transmission The screen in Figure 5 8 appears Y PLANET A e Port Trunk Setup CN ET Port 13 14 15 16 Enable Disable Figure 5 8 FNSW 1608PS Port Trunk Setup Web Page screen XA Notice After turn on the port trunk feature port 1 and port 2 or port 13 14 15 16 should connect to another switch such as another FNSW 1608PS that also supports port trunk feature to double the bandwidth in between Otherwise if the connected switch do not support port trunk it will cause network loop and hangs the whole network AQ 5 6 Misc Configuration This section provides Misc Configuration of FNSW 1608PS the screen in Figure 5 9 appears and table 5 3 descriptions the Misc Configuration objects of FNSW 1608PS QPLANET wahaj A er HIF No 96 Min Chuan Road Hein Tian Taipel Taian R O C Tel AAA Fax 856 2 2219 9526 Email Sales planet com te Figure 5 9 FNSW 1608PS Misc Configuration Web Page sc
28. he cable is the right type Turn off the power After a while turn on power again Why connect my PoE device to FNSW 1608PS and it cannot power on Solution 1 Pleasecheckthe cable type of the connection from FNSW 1608PS port 1 to port 8 to the other end The cable should be an 8 wire UTP Category 5 or above ElA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply 2 Please check and assure the device that fully complied with IEEE 802 3af standard How to deal forgotten password situation of FNSW 1608PS Solution 1 Please contact Planet switch support team and the mail address is support_switch planet com tw 57 APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ 45 Pin Assignments SES A 2 RJ 45 cable pin assignment Da There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable ES E 12345678SIDE 1 41 wWhitelfOrange 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green d Blue 4 Blue 5 White Blue 5 White Blue 12346567 6 SIDE 2 6 Green 6 Green T White Brown T White Brown 8 Brown 8 Brown SIDE 1 SIDE 2 12346566 7 8 SIDE 1 1 White Orange 1 White Green 7 2 Orange 2 Green 3 White Green 3 White Orange 4 Blue 4 Blue ce 5 White Blue 5 White
29. he factory default user name is admin without password You may change the password by use set pass command Please always enter the correct user name and password See Figure 4 2 FNSW 16408PS System init sys init gt walt state reg x 86d Ux28 ip inspc reg 4 x 661 Bx3f done lt FNSW 1608PS System timer init done FASH 16B88PS5 Eth init done current tick 800003 sec EEPROM Init Write EE_TEST 6x cf u8EEDatal 0xaa Read EE_TEST x cf usEEDatal Bxaa EEPROM 24c16 found InYalid EEPROH Restore Default Value Show MY IP Address 192 168 6 186 Initial EEPROH Initial MAC Registers ACCESS POWER ICO D K ACCESS POWER ICI O K FNSW 1608PS Uip init login admin password Figure 4 2 FNSW 1608PS login screen 4 3 Main Menu screen After login the FNSW 1608PS the main menu screen shows as below walt state reg x H6d Ox 2 Ip inspc reg Bx 001 Ox3f done lt FNSW 1608PS System timer init done FNSW 1668PS Eth init done current tick 86000803 sec EEPROM Init Write EE_TES x cf usEEDatal Bxaa Read EE_TEST x cf u8EEDatal Oxaa EEPROM 24c16 found InYalid EEPROH Restore Default Value Show MY IP Address 1927 168 0 100 Initial EEPROH Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER ICI O K FNSW 1608PS Uip init login admin password FNSH 1608P5 gt
30. idth The FNSW 1608PS supports MDI MDI X convertible on 16 10 100Mbps ports also provide PoE inject function on port 1 to 8 which is able to drive 8 IEEE 802 3af compliant powered devices The dual speed ports use standard twisted pair cabling and are ideal for SOHO or segmenting networks into small Each 10 100Mbps port can supports up to 200Mbps of throughput in full duplex mode the FNSW 1608PS also provides a simple cost effective and highly reliable network connection for data as well as power Furthermore it is the ideal device for bridging among Ethernet Fast Ethernet workgroups and networks With 8 PoE interfaces the FNSW 1608PS is ideal for small business and workgroups requiring to deploy the PoE for the wireless access points IP based surveillance camera or IP phones in any places easily efficiently and cost effective The front panel of FNSW 1608PS provides LEDs for easy recognition of the switch operation status and troubleshooting These LED indicators display the power status for the system LNK ACT and speed for each10 100M port Also the PoE in use LED indicates for PoE ports port 1 to port 8 With data and power over Ethernet from one unit the FNSW 1608PS shall reduce cables and eliminates the need for dedicated electrical outlets on the wall ceiling or any unreachable place A wire carries both data and power lowering the installation costs simplifying the installation effort and eliminating the need for electricians or ex
31. ing frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability The Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for con necting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Ethernet switching the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its re spective domain reducing the overall load on the network The Switch performs Store and forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 6 5 Auto Negotiation The STP ports on the FNSW 1608PS switch have built in Auto negotiation This technology automatically sets
32. init legin admin password FNSW 1608PS gt set management vlan Select management vlan group 1 16 1 FNSW 1688PS gt Figure 4 23 Management VLAN Configuration screen XA Notice Before use this function please enable port based VLAN function and assign member port into 16 port based VLAN groups 27 4 4 3 6 Set vlan mode This command allows disable or enable port based vlan function of FNSW 1608PS the vlan mode setting screen in Figure 4 24 appears current tick 68600003 sec EEPROM Init Write EE_TEST x cf u8EEDatal xaa Read EE_TEST x cf us8EEDatal Bxaa EEPROM 24c16 found InYalid EEPROM Restore Default Value Show MY IP Addres 192 168 8 100 Initial EEPROM Initial MAC Registers ACCESS POWER ICH O K ACCESS POWER IC1 O K FNSW 1668PS Uip init login admin password FNSW 1688PS gt set vlan mode Select VLAN mode 1 No VLAN 2 Port based VLAN 2 Please wait FNSH 1608P5 gt Figure 4 24 VLAN mode Configuration screen 4 4 3 7 Set pvid This command allows assign PVID of each port from FNSW 1608PS the PVID setting screen in Figure 4 25 appears EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show MY HAC Address from 24c16 0x00 30 4f 00 00 00 _ 4c16 eeprom word read EE _DHCPEN 6 gt DHCP FALSE Show HY IP Address from 24c16 192 168 060 106 Show DNS Server from 24c16 168 95 192 61
33. l 1 Disable 2 128K 3 256K 4 512K 5 1M 6 2M 7 4M 8 8H Port Priority Mapping 1 High Queue 2 Low Queue 1 Port 1 configuration information Auto Negotiation Enable Speed ability 106M Full 166M Half 10M Full 10M Half Priority Tagging Control Disable TA Bandwidth Control Disable RA Bandwidth Control Disable Port Priority Mapping High Queue FNSH 1608P5 gt Figure 4 19 Port Configuration screen 24 Object Description Speed Ability 10M Half Allow set per port run at 10Mbps half soeed mode are Disable Remove Tag Insert Tag assign per port transmit bandwidth the available options are Disable 128K 256K 512K 1M 2M 4M 8M RX Bandwidth control Allow assign per port receive bandwidth the available options are Disable 128K 256K 512K 1M 2M 4M 8M Port Priority Mapping Allow assign low queue or high queue on each port Table 4 2 Descriptions of the Port Configuration screen Objects 4 4 3 2 Set trunk This command allows disable or enable trunk function of two ports or four ports from FNSW 1608PS The trunk function setting screen in Figure 4 20 appears Restore Configuration from EEPROM to Device Show MY HAC Address from 24c16 0x00 30 4f 00 00 00 _24c16 eeprom_word_read EE_DHCPEN 06 gt DHCP FALSE Show MY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom word read EE _DHCPEN 00 DHCP FALSE webt_ee network
34. l description shown in table 4 3 Portl POE Enable POE Priority 1 FNSW 1668PS gt set poe POE Port 2 1 Enable 2 pisable El POE Port 2 Priority 0 3 2 Port POE Enable POE Priority 2 FNSW 1698PS gt set poe POE Port 3 1 Enable 2 0i sable POE Port 3 Priority 8 3 2 Port3 POE Enable POE Priority 2 FNSH 1608P5 gt Figure 4 22 PoE port Configuration screen 26 Object Description POE Port 1 8 1 Enable 2 Disable Allow disable or enable each POE port POE Port 1 8 Priority 0 3 Assign POE power provision priority 0 3 to each POE port Table 4 3 Descriptions of PoE port Configuration screen Objects 4 4 3 5 Set management vian This command allows assign one VLAN as management VLAN of FNSW 1608PS Only the assigned VLAN group can manage The management vian function setting screen in Figure 4 23 is as below EEPROM Init Write EE_TEST 6x cf usEEDatal Bxaa Read EE_TEST Bx2cf u8EEDatal xaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show MY HAC Address from 24c16 0x00 30 4f 00 00 00 _ 4c16 eeprom word read EE _DHCPEN 60 gt DHCP FALSE Show MY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom word read EE DHCPEN 66 DHCP FALSE webt ee network dhcp flag 6x66 Initial MAC Registers ACCESS POWER ICH O K ACCESS POWER IC1 O K FNSW 1608PS Uip
35. onfigured the switch will automatically restart as the following screens After reboot the Switch and power on completed you can use the new IP address access of FNSW 1608PS The IP subnet address setting screen in Figure 4 27 amp 4 28 appears Show HY IP Address from 24c16 192 168 0 100 Show DNS Server from 24c16 168 95 192 M1 _24c16 eeprom_word_read EE DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 6x66 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER 101 O K FNSW 1688PS Uip init login admin password ae set ip 192 168 0 1 299 299 299 0 192 168 0 24 2 3 The IP sets to 192 168 0 1 The Netmask sets to 209 209 299 0 The Gateway sets to 192 168 0 254 The system will restart FNSW 1608P gt Reset System Figure 4 27 IP subnet address configuration screen Ip inspc reg 6x O61 Ox3f done lt FNSW 1608PS System timer init done FNSW 1668PS Eth init done current tick 6600063 sec EEPROM Init Write EE TEST Bx2cf u8EEDatal Oxaa Read EE_TEST x cf usEEDatal Mxaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show HY MAC Address from 24c16 0x00 30 4f 00 00 00 _24c16 eeprom word read EE _DHCPEN 8 gt DHCP FALSE Show HY IP Address from 24c16 192 168 0 1 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom word read EE_DHCPEN 68 DHCP FALSE webt_ee network dh
36. ort based VLAN function of FNSW 1608PS Assign PVID on each port of FNSW 1608PS Allow to configure the priority setting of FNSW 1608PS Assign IP address subnet mask gateway of FNSW 1608PS Change the default password of FNSW 1608PS the maximum length is 4 characters Reset the FNSW 1608PS to factory default mode Reboot the FNSW 1608PS Logout console interface of FNSW 1608PS 10 Please refer to the following Chapter 4 and 5 for the details 3 2 Management Methods There are two ways to manage the FNSW 1608PS Local Console Management via the Switch serial port Web Management via a network or dial up connection 3 2 1 Local Console Management You can manage the FNSW 1608PS locally by connecting a VT 100 terminal or a personal computer or workstation with terminal emulation software to the Switch serial port The terminal or workstation connects to the Switch serial port using a null modem cable that has the appropriate connectors on each end This management method is ideal when The network is unreliable The Network Manager does not have direct network connection The serial port of the Switch default setting is set to 19200 baud using a character format of 8 data bits no parity and 1 stop bit Therefore configure the terminal or workstation to use these settings before you log on to the FNSW 1608PS You can change this default setting if desired after you log on 3 2 2 Web Management You can m
37. reen Object Description System Info Allow user to configure the system configuration please refer to chapter 5 6 1 Password Access Setting Allow user to change the password and maximum up to 4 characters please refer to chapter 5 6 2 Reboot System Allow user to reboot the FNSW 1608PS please refer to chapter 5 6 4 Firmware Upgrade Allow user to proceed the firmware upgrade process of FNSW 1608PS please refer to chapter 5 6 5 Table 5 3 Descriptions of the Misc Configuration screen Objects Restore System Default Allow user to reset the FNSW 1608PS to factory default mode please refer to chapter 5 6 3 A1 5 6 1 System Information This section provides System Configuration of FNSW 1608PS the screen in Figure 5 10 appears and table 5 4 descrip tions the System Configuration objects of FNSW 1608PS r y Lf F s Piast m AAA mt rep FETI E A Erin rra System Configuration IP Address i Figure 5 10 FNSW 1608PS System Configuration Web Page screen Description Display Mac address of FNSW 1608PS Display firmware version of FNSW 1608PS Allow user to select management VLAN and available options is 1 to 16 The screen in Figure 5 11 appears TCP IP TOS DS Priority Allow user disable or enable TCP IP TOS DS Priority function Allow user disable or enable 802 1p Priority function Queue service rate Allow user to select queue service rate and available options are 4 1 8 1 16 1 N The screen in Figure 5 12
38. rs J PLANET Porat lima VLAN Setting Por based VLAN No VLAN Hui binm WLAN Figure 5 5 FNSW 1608PS VLAN Setting Web Page screen Select Port based VLAN and press Apply button to enable the port based VLAN function then continue configure sixteen port based VLAN groups as your request After setup completed please press Apply to take affect and press Next for next page The screen in ak ai 5 6 amp 5 7 appears PLANET Heledaking A Commarclin a Fort Status I Por Setup E VLAN Setup Fort Trunk Setup a a A is 22 a oJo o oJotoJoJofof fofofojo En HHA opofofofofofo o o a er 38 Figure 5 6 FNSW 1608PS port based VLAN Setting Web Page screen Aris AN Fanki VLAN Setting F bbisid LAN Aor Figure 5 7 FNSW 1608PS port based VLAN Setting Web Page screen 5 4 1 VLAN setting example VLAN scenario 1 Port 16 is the file server port for all the workstations 2 Port 1 to port 15 is different devices that do need to see each other Setup steps 1 Port Setting 1 1 Assign VLAN 1 as the default VLAN group for all ports 1 2 Assign VLAN 2 for the second VLAN group with port 1 and port 16 1 3 Repeat the same steps for port 2 to port 15 i e 2 amp 16 3 amp 16 1548416 2 PVID setup 2 1 Assign 1 i e ID of VLAN 1 to port 16 as its PVID Port VLAN ID 2 2 Assign 2 to port 1 as its PVID 2 3 Repeat above steps for port 2 to port 15 wit
39. rt3 On Off OFF FNSH 1608P5 gt show poe status 4 Port On Off Off FNSH 1608P5 gt show poe status 3 Porto On Off OFF FNSH 1608P5 gt show poe status 6 Figure 4 12 Per poe port link status screen 20 4 4 2 7 Show poe n Display the poe status on each port of FNSW 1608PS this command allows you to view per poe port status of the Switch and the correct usage is shown as below Show poe n n 1 8 to view per poe port status of FNSW 1608PS The per poe port status screen in Figure 4 13 ap pears Portl POE Enable POE Priority FNSW 1688P gt show poe 2 Port POE Enable POE Priority FNSH 1608P5 gt show poe 3 Port3 POE Enable POE Priority FNSH 1608P5 gt show poe 4 Port POE Enable POE Priority FNSH 1608P5 gt Figure 4 13 Per poe port status screen 4 4 2 8 Show management vlan Display the management vlan of FNSW 1608PS the management vlan display screen in Figure 4 14 appears Write EE TEST x cf usEEDatal Bxaa Read EE_TEST 0x cf u8EEDatal xaa EEPROM 24c16 found EEPROM Data valid Restore Configuration from EEPROM to Device Show HY MAC Address from 24c16 0x00 30 4f 00 00 00 _24c16 eeprom_word read EE_DHCPEN 6 gt DHCP FALSE Show HY IP Address from 24c16 192 168 060 100 Show DNS Server from 24c16 168 95 192 61 _24c16 eeprom word read EE_DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 6x00 Initial MAC Registers ACCESS POWER ICO
40. set vlan mode set pvid set priority set 1 XXX WMM XKW MMA MMM MMM mmm mmm ggd gag gqgg ggg set pass FNSW 1686P5 gt Figure 4 18 Set command list screen 93 This set command list contains ten items Set port n Please refer to chapter 4 4 3 1 Set trunk Please refer to chapter 4 4 3 2 Set vian n Please refer to chapter 4 4 3 3 Set poe n Please refer to chapter 4 4 3 4 Set management vlan Please refer to chapter 4 4 3 5 Set vlan mode Please refer to chapter 4 4 3 6 Set pvid Please refer to chapter 4 4 3 7 Set priority Please refer to chapter 4 4 3 8 Set ip Xxx Xxx XXx XXX Mmm mmm mmm mmm ggg ggg ggg ggg Please refer to chapter 4 4 3 9 Set pass Please refer to chapter 4 4 3 10 4 4 3 1 Set port n This command allows configuring per port parameters of FNSW 1608PS the correct usage is shown as below Set port n n 1 16 to configuring per port parameters of FNSW 1608PS The configuring per port parameters screen in Figure 4 19 appears and the detail description shown in table 4 2 FNSH 1608PS5 gt set port 1 Auto Negotiation 1 Enable 2 Disable 1 Speed Ability 100N Full 1 Yes 2 No 1 Speed Ability 100M Half 1 Yes 2 No 1 Speed Ability 16M Full 1 Yes 2 No 1 Speed Ability 10M Half 1 Yes 2 No 1 Priority Tagging Control 1 Disable 2 Remove Tag 3 Insert TX Bandwidth Control 1 Disable 2 128K 3 256K 4 512K JH Qe 7 4H 8 8H n ak i Bandwidth Contro
41. show pvid show priority FNSW 1668PS gt show port 1 Port 1 configuration information Auto Negotiation Enable Speed ability Priority Tagging Control TH Bandwidth Control RA Bandwidth Control Port Priority Mapping FNSW 1668PS gt 166M Full 100M Half 10H Full 10H Half Disable Disable Disable Low Queue Figure 4 6 Per port Status screen a ae password FNSW 1668PS gt show port Port Link Speed Duplex FlowControl Port 1 Down 10H half Enable Port 2 Down 10H half Enable Port 3 Down 10H half Enable Port 4 Down 18M half Enable Port b Down 16H half Enable Port 6 Down 10H half Enable Port Down 10H half Enable Port 8 Down 16H half Enable Port 9 Down 10H half Enable Port 16 Down 10H half Enable Port 11 Down 10H half Enable Port 12 Down 16H half Enable Port 13 Down 18M half Enable Port 14 Down 10H half Enable Port 15 Up 100 full Enable Port 16 Up 1090H full Enable FNSW 1608P gt _ Figure 4 7 All port Status screen 4 4 2 2 Show vlan n Display one specific VLAN group status of FNSW 1608PS the correct usage is shown as below Show vlan n n 1 16 to view one specific VLAN group status of FNSW 1608PS the VLAN group status screen in Figure 4 8 appears Eag Ai 123496789 10 11 12 13 14 15 16 FNSW 1688PS gt show vlan 2 vlan 123456789 10 11 12 13 14 15 16 FHSH 1608P gt show vlan 3 gan 123456789 10 11 12 13 14 15 16 FNSW 1688PS gt show vlan 4 wian 123436789 1011 12 1
42. ss table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Ethernet Switch 6 2 Learning When one packet comes in from any port The Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 6 3 Forwarding amp Filtering When one packet comes from some port of the Ethernet Switching it will also check the destination address besides the source address learning The Ethernet Switching will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Ethernet Switching will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increasing the network throughput and availability 6 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Ethernet Switching stores the incom
43. tension cords We are also oroud of the key feature energy saving With more efficient switching power supply the efficiency of the FNSW 1608PS would be much better than four linear power adapters in a long run The smart functions make it easy to survey and control the PoE power provision to the devices by the Web and Console interface Basic switching functions such as VLAN Trunk QoS and bandwidth control are available for network man agement 1 3 Features Comply with IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3x Flow Control and IEEE 802 3af Power over Ethernet e 16 Port 10 100Mbps Fast Ethernet ports e 8 Port support 48VDC power to PoE Powered Device e Each switching ports support suto negotiation 10 20 100 200Mbps supported e Prevent packet loss with back pressure half duplex and IEEE 802 3x PAUSE frame flow control full duplex High performance Store and Forward architecture broadcast storm control runt CRC filtering eliminates erroneous packets to optimize the network bandwidth Support 8K absolute MAC addresses automatic address learning and address aging LED indicators for easy network diagnostic e Local console and remote web management interface Auto negotiation speed duplex mode control and bandwidth control QoS setting on each port VLAN for network segregation and support up to 16 port based VLAN groups e Management VLAN function support Support two trunk groups an
44. tered you will see the web main menu screen 2362 PLANET Maira Cial Welcome to PLANET FNSW 1608PS Web Smart Manager LANET Technology Corporation 11 Mo 96 Min Chuan Road Ham Tien Taipei Taiwan K C Tel 656 2 219 519 Fax A Figure 5 2 The web main menu screen of FNSW 1608PS 5 2 Port Status This section provides current status of each port from FNSW 1608PS the screen in Figure 5 3 appears and Table 5 1 describes the port status object of switch PLANET A i Cnm Port Status Part Number Port a sa Pon gie Pon gie RI E AECI E E rare TE ua Enable a AC ZN AT E AT INEA E EE MECO DECO TN E IT TE Figure 5 3 FNSW 1608PS Port Status Web Page screen 36 Description Pot Indicate port 1 to port 16 The state of the link indicating a valid link partner device Up means a device is successful connected to the port Down means no device is connected Display the 10Mbps or 100Mbps speed state of each port on FNSW 1608PS Duplex Display half or full duplex mode of each port on FNSW 1608PS Flow Control Display the flow control Disable or Enable state of each port on FNSW 1608PS Auto Negotia Display the Auto negotiation Disable or Enable state of each port on FNSW 1608PS tion Table 5 1 Descriptions of the Port Status screen Objects 5 3 Port Setup This section introduces detail settings of per port on FNSW 1608PS the screen in Figure
45. teway 192 168 0 1 FNSH 1608P5 gt Figure 4 10 IP subnet address information screen 4 4 2 5 Show system Display the system information of FNSW 1608PS such as software version mac address and IP address The system information screen in Figure 4 11 appears EEPROM Data valid Restore Configuration from EEPROM to Device Show MY MAC Address from 24c16 0x00 30 4f 00 00 00 _ 4c16 eeprom word read EE _DHCPEN 66 gt DHCP FALSE Show MY IP Address from 24c16 192 168 606 180 Show DNS Server from 24c16 168 95 192 01 _24c16 eeprom _word read EE_DHCPEN 00 DHCP FALSE webt_ee network dhcp flag 6x00 Initial MAC Registers ACCESS POWER ICO O K ACCESS POWER IC1 O K FNSW 1668PS Uip init login admin password FNSW 1668PS gt show system PLANET FNSH 1608P5 Software Version 1 0 MAC 00 30 4f 00 00 06 IP 192 168 8 100 FNSH 1605P5 gt Figure 4 11 System information screen 4 4 2 6 Show poe status n Display the poe link status on each port of FNSW 1608PS this command allows you to view per poe port link status of the Switch and the correct usage is shown as below Show poe status n n 1 8 to view per poe port link status of FNSW 1608PS The per poe port link status screen in Figure 4 12 appears login admin password FNSH 1608P5 gt show poe status 1 Portl On Off OFF FNSH 1608P5 gt show poe status 2 Port On Off Off FNSH 1608P5 gt show poe status 3 Po
46. that deposit in your PC and press Upgrade to start the firmware upgrade process The screen in Figure 5 26 appears Upgrade Firmware Pesse salact a file hin to upgrade C Documents and Sotle Browser Upgrade Upgrading hrmeware may take 60 seconds COO i Upgrade must NOT be interrupted Figure 5 26 The FNSW 1608PS firmware upgrade Web Page screen Please wait for twenty four seconds and go to next firmware upgrade web page the screen in Figure 5 27 appears 50 Please wating a moment and click button to next step wan q 2 4 Figure 5 27 The FNSW 1608PS firmware upgrade Web Page screen Then the re login screen appears in Figure 5 28 please press Re Login button to re login web interface of FNSW 1608PS with latest firmware version the screen in Figure 5 29 appears Pliach wating mam n and chek button to next step Figure 5 28 The FNSW 1608PS firmware upgrade Web Page screen 51 FNSW 1608PS Login Please enter your Usemame and Password Dyer admin Password Figure 5 29 The FNSW 1608PS login Web Page screen XA Notice Please does not power off the FNSW 1608PS during firmware upgrade process 52 5 7 POE This section provides POE status and POE configuration of FNSW 1608PS the POE Status screen in Figure 5 30 appears and Table 5 5 describes the POE status eon of FNSW 1608PS Qf PLAN ET FNSW 1608PS W a P art P Figure 5 30 FNSW 1608PS POE Status Web P
47. the best possible bandwidth when a connection is established with another network device usually at Power On or Reset Detecting the modes does this and speeds at the second of both devices are connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full duplex mode 56 7 TROUBLESHOOTING This chapter contains information to help you solve problems If the Switch is not functioning properly make sure the Ethernet Switch was set up according to instructions in this manual The Link LED is not lit Solution Check the cable connection and remove duplex mode of the Switch Some stations cannot talk to other stations located on the other port Solution Please check the VLAN port trunking function that may introduce this kind of problem Performance is bad Solution Check the full duplex status of the Ethernet Switch If the Ethernet Switch is set to full duplex and the partner is set to half duplex then the performance will be poor 100Base TX port link LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Switch doesn t connect to the network Solution Check the LNK ACT LED on the switch Try another port on the Switch Make sure the cable is installed properly Make sure t
48. ty of FNSW 1608PS Show current management VLAN of FNSW 1608PS Show current VLAN mode of FNSW 1608PS Show per port PVID of FNSW 1608PS Show current priority status of FNSW 1608PS Set per port auto negotiation speed duplex mode QoS and bandwidth control Insert priority tagging function of FNSW 1608PS 15 Set Trunk Disable or enable trunk group of FNSW 1608PS Set VLAN n Configure port based VLAN group of FNSW 1608PS Set PoE n Configure per PoE port of FNSW 1608PS Set management VLAN Assign management VLAN of FNSW 1608PS Set VLAN mode Disable or enable port based VLAN function of FNSW 1608PS Set PVID Assign PVID on each port of FNSW 1608PS Set priority Allow to configure the priority setting of FNSW 1608PS Set IP XXX XXX XXX XXX mmm mmm mmm mmm Assign IP address subnet mask gateway of FNSW 1608PS 999 999 999 999 Set Pass Change the default password of FNSW 1608PS the maximum length is 4 characters Factory Default Reset the FNSW 1608PS to factory default mode Reboot Reboot the FNSW 1608PS Logout Logout console interface of FNSW 1608PS Table 4 1 Detail description of FNSW 1608PS available commands XA Notice Only accept command in lowercase letter under console interface 4 4 2 Show command From the main menu screen see Figure 4 3 input show and press enter The show command list screen in Figure 4 5 appears DHCP FALSE webt_ ee network dhcp flag 6x60 Initial MAC Registers AC
49. using incorrect screws would invalidate your warranty Step 3 Secure the brackets tightly Step 4 Follow the same steps to attach the second bracket to the opposite side Step 5 After the brackets are attached to the Switch use suitable screws to securely attach the brackets to the rack as shown in Figure 2 4 44 0000000 Figure 2 4 Mounting the Switch in a Rack Step 6 Proceed with the steps 4 and steps 5 of section 2 3 1 Desktop Installation to connect the network cabling and supply power to your Switch 2 3 3 As a department workgroup PoE Switch Providing up to 8 PoE in line power interface the FNSW 1608PS can easily build a power central controlled IP phone system IP Camera system AP group for the enterprise For instance 8 camera AP can be easily installed around the corner in the company for surveillance demands or build a wireless roaming environment in the office Without the power socket limitation the FNSW 1608PS makes the installation of cameras or WLAN AP more easily and efficiently ICA 100PE _ WAP 4060PE f ICA 100PE FNSW 1608PS VIP 153PT POE Connection Ethrnet Connection Figure 2 5 PoE Switch connection 3 SWITCH MANAGEMENT This chapter describes how to manage the FNSW 1608PS Topics include Overview Management methods Assigning an IP address to the FNSW 1608PS Logging on to the FNSW 1608PS 3 1 Overview The FNSW 1608PS pro
50. vides a user friendly command line under console interface Using this interface you can perform various switch configuration and management activities including Command Show port n all Show VLAN n Show trunk Show IP Show system Show POE status n Show PoE n Show management VLAN Show VLAN mode Show PVID Show Priority Set port n Set Trunk Set VLAN n Set PoE n Set management VLAN Set VLAN mode Set PVID Set priority Set IP XXX XXX XXX XXX mmm mmm mmm mmm 999 999 999 999 Set Pass Factory Default Reboot Logout Description Show per port or all port current status of FNSW 1608PS Show current VLAN group status of FNSW 1608PS Show current trunk group status of FNSW 1608PS Show current IP subnet address of FNSW 1608PS Show firmware version Mac address and IP address of FNSW 1608PS Show per PoE port status On or Off of FNSW 1608PS Show per PoE port disable enable status and priority of FNSW 1608PS Show current management VLAN of FNSW 1608PS Show current VLAN mode of FNSW 1608PS Show per port PVID of FNSW 1608PS Show current priority status of FNSW 1608PS Set per port auto negotiation speed duplex mode QoS and bandwidth control Insert priority tagging function of FNSW 1608PS Disable or enable trunk group of FNSW 1608PS Configure port based VLAN group of FNSW 1608PS Configure per PoE port of FNSW 1608PS Assign management VLAN of FNSW 1608PS Disable or enable p
51. you to re login web interface with correct username admin and password the screen in Figure 5 21 amp 5 22 amp 5 23 appears PLANET Ario jh Lit ted cited Welcome to PLANET FNSW 1608PS Web Smart Manager a al fo 96 Min Chuan Road Hsin Tien aoe rias Taipe Tarwan ROC R Gosek arai ian Tel 886 2 2219 9518 a Fax 986 2 2219 9528 Emad Salergbiplaner com tw Figure 5 20 The FNSW 1608PS reboot system Web Page screen 47 GQ PLANET 9 PLANET Figure 5 21 The FNSW 1608PS rebooting Web Page screen Figure 5 22 FNSW 1608PS Re Login Web Page screen 48 FNSW 1608PS Login Please enter your Username and Pazeweord Username admin Password Figure 5 23 The FNSW 1608PS login Web Page screen 5 6 5 Firmware Upgrade This section provides firmware upgrade of FNSW 1608PS after choose this function and the following screen appears in Figure 5 24 Please press Update button to continue following firmware upgrade process Arteries A AA Figure 5 24 The FNSW 1608PS firmware upgrade Web Page screen Please wait for two seconds and press Continue to next firmware upgrade web page the screen in Figure 5 25 appears 49 E oy AJ iy Mir pn r EF AAA A PR E A Finas atm A maniti and click button to next step Figure 5 25 The FNSW 1608PS firmware upgrade Web Page screen Please press Browser to locate the latest firmware of FNSW 1608PS
Download Pdf Manuals
Related Search
Notice notice notice to vacate notice of settlement noticed synonym noticeably notice to employee notice of privacy practices notice 123 notice of intent notice to consumer notice to quit notice of transfer and release of liability notice of hearing notice of acknowledgment and receipt notice of entry of judgment noticeable synonym notice to mariners notice format notice of change of address notice of remote appearance form ra-010 notice period notice of appearance notice of release of liability notice board notice to vacate letter
Related Contents
Gigabit Ethernet - KnowledgeBase Manager Pro GarrettCom ES42 User's Manual User Manual GreatCall Jitterbug Touch User Guide Linux Smart Home Touch Panel User Manual 平成26年 広告監修(H26)指導実績 正会員 取扱説明書 - 無印良品 Ubiquiti Networks mPort Copyright © All rights reserved.
Failed to retrieve file