Quick Start Guide ELPRO 905U-LT Wireless I/O
Contents
1. Quick Start Guide ELPRO 905U L T Wireless I O Transmitter Unit man 905U L T QuickStart vi 9 doc About this document This document is the ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide and contains the following sections ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide Section Read this section if you want to Basic steps for using vour unit Factorv default configuration Resetting factorv defaults Reset vour unit to the original factorv default settings Linking transmitter and receiver units Link your units to work as a dedicated pair Safety information Understand important safety information related to your unit NOTE You must read this information before installing your unit Specifications Know technical information about your unit For more information see the next sections Basic steps for using your unit This document describes how to configure your unit using the default factory configuration that lets you easily setup your network as a simple send receive network using a dedicated pair of transmitter and receiver units The basic steps for using your unit are 1 Connect the antenna power supply and transducer signals using the instructions in this document Power supply and transducer connection is described in the section Unit components and connections Antenna connection is described in the section Antenna installation For more information see the 905U L2. Installation Manual Reset the transmitter and receiver units to the factory default configurations Link the transmitter and receiver units to work as a dedicated pair Bench test your configuration before deploying NOTE You can also configure your network using a user defined customised configuration that lets you set specific information about your network For more information on setting a user defined customised configuration see the 905U L User Manual on the enclosed CD Factory default configuration When you configure the units using the configuration in this document the inputs from the transmitter are sent to the outputs at the receiver as follows 905U L T Transmitter Sends 905U L R Receiver Thermocouple Input Not used Communication Failure Comes on if no messages from 905U LT Setpoint Output Local marcaron __ System OK On if system OK System OK On if system OK ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 2 of 8 Unit components and connections Your 905U L transmitter unit has the following components and terminal connections Earth Wire Lug underneath Unit ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide SYSTEM OK PF STATUS COMMON 4 POWER SUPPLY COMMON COMMON THERMOLQLUPLE fm Max MD LC SOO la Thermocouple type J Kor T Forinductye load orm signal yse surge diodes A Loop powered sensor shown r
3. ade by ELPRO or its representatives or by any other party except as expressed solely in this document ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 8 of 8
4. cific Industry Canada certification number and any other certification designations NOTE Any changes or modifications not expressly approved by ELPRO Technologies P L could void the user s authority to operate this equipment To operate this equipment legally the user must obtain a radio operating license from the government agency This is done so the government can coordinate radio users in order to minimize interference Safety information FCC Notice This device complies with Part 15 247 of the FCC Rules Operation is subject to the following two conditions gt This device may not cause harmful interference and gt This device must accept any interference received including interference that may cause undesired operation NOTE This equipment is suitable for use in Class Division 2 groups A B and C or non hazardous locations only UL Notice 1 The Wireless I O module is to be installed by trained personnel licensed electricians only and installation must be carried out in accordance with the instructions listed in the Installation Guide and applicable local regulatory codes 2 The units are intended for Restricted Access Locations PS The Wireless I O module is intended to be installed in a final enclosure rated IP54 before use outdoors 4 The Equipment shall be powered using an external Listed Power Supplv with LPS outputs or a Class 2 Power Supply 5 The Wireless I O module must be properly grounded for surge pro
5. e Low Digital Input 2 is active All LEDs medium flash Medium speed flash 1 6HZ indicates the module is half way through the configuration process Medium flash also happens when you set the rotary switch to position O when powering on the unit Antenna installation im minimum Collinear antenna Objects j e g walls Weatherproof connectors e g 3M 23 tape etc Surge protector arrestor optional Stress relief loop ELPRO Unit You must provide good ground connection to the mast unit and surge arrestor protector Earth Stake A You must install the aerial above all local obstructions ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 5 of 8 Resetting vour unit to factorv defaults To reset the default factorv configuration ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide 1 Setthe RSSI rotarv switch to position O using a screwdriver 2 Power on the 905U L transmitter 3 The 905U L transmitter flashes all LEDs at medium flash i e 1 6 Hz NOTE If the LEDs do not flash you must repeat steps 1 and 2 until the LEDs flash before continuing 4 Set the RSSI rotary switch to another position i e position 1 within 5 seconds 5 Set the RSSI rotary switch to position O within another 5 seconds 6 The 905U L transmitter lights all LEDs for 2 seconds before returning to normal operation NOTE If the LEDs do not light for 2 seconds you must repea
6. ech com Copyright Copyright ELPRO Technologies Pty Ltd All rights reserved Limited lifetime warranty disclaimer and limitation of remedies ELPRO products are warranted to be free from manufacturing defects for the serviceable lifetime of the product The serviceable lifetime is limited to the availability of electronic components If the serviceable life is reached in less than three years following the original purchase from ELPRO ELPRO will replace the product with an equivalent product if an equivalent product is available This warranty does not extend to Failures caused by the operation of the equipment outside the particular product s specification or Use of the module not in accordance with this User Manual or Abuse misuse neglect or damage by external causes or Repairs alterations or modifications undertaken other than by an authorized Service Agent ELPRO s liability under this warranty is limited to the replacement or repair of the product This warranty is in lieu of and exclusive of all other warranties This warranty does not indemnify the purchaser of products for any consequential claim for damages or loss of operations or profits and ELPRO is not liable for any consequential damages or loss of operations or profits resulting from the use of these products ELPRO is not liable for damages losses costs injury or harm incurred as a consequence of any representations warranties or conditions m
7. il Externally powered sensors are Ae Isa suitabi kl also suitable Dl s suitable forwol free contacts or HF transistar dew ces POWER SUPPLY 9 30 VDC BOCs 12 JOOMA i 2 In order to complv with Electrical Safetv Regulations this module must be installed in an Electrical AND Fire enclosure This enclosure mav be a single or multiple enclosures Access to the module is to be made bv a Service Person oniv ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 3 of 8 The front panel contains the following components ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide SMA antenna connector at topofunit i RS232 configuration port Rotarv switch for set point settings NOTE To avoid damaging the rotary switch use a screwdriver to change the position The rotary switch uses the following setpoint levels Position Lower level mA Upper level mA a fa Jo ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 4 of 8 The LEDs on the front panel indicate the unit status ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide LED Status Indicates No power supplv OK LED Green OK LED Red TX Led Flashes PG LED on Configuration Cable Connected Input LED ON Input LEDS i e D1 D2 SP AZ light when the corresponding input is active Current status of the unit OK Fault condition detected in unit Transmitting Message Digital Input 1 is activ
8. t the process from step 1 until the LEDs light before continuing 7 You can now link the transmitter and receiver units Linking your transmitter and receiver units You must reset the transmitter unit to factory defaults to disable encryption before linking the transmitter and receiver units For more information see the previous section NOTE You must complete the linking process in 60 seconds To link the transmitter and receiver units 1 Press and hold down the RSSI Pushbutton on the receiver 2 Power on the receiver while holding down the RSSI Pushbutton 3 Release the RSSI Pushbutton as soon as the Receiver LEDS flash within 5 seconds of powering the receiver 4 The receiver will flash all LEDs for a maximum 60 seconds while it tries to link to the transmitter 5 Power on the transmitter The transmitter sends a special Link message to allow the receiver to recognise the transmitter 6 When the units link the receiver lights all LEDs for 2 seconds before returning to normal operation NOTE If the receiver LEDs continue flashing within the 60 seconds the units are not linked and you should retry the linking process by powering the transmitter off and on again If you exceed the 60 seconds you must restart the linking process from step 1 7 You can now bench test your configuration before deploying ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 6 of 8 Safetv information Thank yo
9. tection before use ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 page 7 of 8 Unit specifications input output Number Additional information ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide Drv contact digital inputs slow pulsed at 10Hz All inputs are suitable for voltage free contacts e g mechanical switches or NPN transistor devices e g electronic proximity switches NOTE PNP transistor device inputs are NOT suitable 0 20mA differential input 16 bit resolution 0 1 accuracy 10 ohm input impedance Digital inputs Analog inputs inputs 9 30 VDC 1 Amp CSA certified Class 2 power supply For use in Class 1 Div 2 explosive areas the power supply must be approved for Class 1 Div 2 use WENA Explosion hazard do not disconnect while circuit is Power supply live unless area is Known to be non hazardous 1 Watt Frequency Hopping Spread Spectrum FHSS Transmitter 902 928 MHz Actual frequency range depends on country Document information Quick Start Guide ELPRO 905U L T Wireless I O Transmitter Unit Version 1 9 ELPRO contact details mn inputs J K or T type thermocouple with on board cold junction compensation Cold junction compensation accuracy 1 over ambient temp range 40 to 70 C Address gt 9 12 Billabong Street Stafford QLD 4053 Telephone gt 61 0 7 3352 8600 Fax gt 61 0 7 3352 8677 Email gt sales elprotech com Website gt www elprot
10. u for selecting the 905U L transmitter for your telemetry needs We trust it will give you many years of valuable service To ensure your 905U L transmitter enjoys a long life double check ALL your connections with the users manual before powering on the unit ELPRO 905U L T Wireless I O Transmitter Unit Quick Start Guide MASINII Incorrect termination of supply wires may cause internal damage and will void warranty Exposure to RF energy is an important safety consideration The FCC has adopted a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93 62 and OET Bulletin 65 Edition 97 01 FCC Notice when used in USA 905U Wireless I O Module Additional information This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of the FCC rules Code of Federal Regulations 47CFR Part 15 Operation is subject to the condition that this device does not cause harmful interference This device has been type accepted for operation by the FCC in accordance with Part90 of the FCC rules 47CFR Part 90 See the label on the unit for the specific FCC ID and any other certification designations Industry Canada 905U Wireless I O Module RSS 119 This device has been type accepted for operation by Industry Canada in accordance with RSS 119 of the Industry Canada rules See the label on the unit for the spe
Download Pdf Manuals
Related Search