User Manual - Power Products
Contents
1. The flash pattern represents a specific fault condition See section Fault Conditions for details When the battery is charged to 80 of capacity the charge status LED will change to GREEN and begin to flash It is recommended that the battery be charged to at least 80 capacity before use The charge status LED will illuminate GREEN with no flashing when the battery is fully charged After removing a fully charged battery the charge status LED may remain illuminated for a few seconds Allow the charge status LED to go off before placing another battery in the charging pod The TWC1 is designed to operate at room temperatures between 15 C and 30 C 59 F 86 F Charging batteries at temperatures outside this range may result in under charging of batteries Fault Conditions When the charge status LED flashes RED a fault condition exists There are three different flash patterns each indicating a specific type of fault The flash patterns and fault conditions are as follows Flash Pattern Fault Type Flashes 1 Time Flashes 2 Times Flashes 3 Times Indicates charging complete but battery is under charged Battery voltage is below minimum level required This warn ing is provided after the rapid charging stage is complete Indicates battery contact is open and current is not passing through the and contacts on the battery This warning is provided after the initial diagnostic st2. specifically for the TWC1 Confirm that the charging pod is compatible with the battery you want to charge 2 Unplug the power supply from the TWC1 3 Turn the locking screw on the bottom of the charging pod counter clock wise several rotations Liftthe charging pod from the charging base 4 Insert the replacement charging pod into the charging base and secure with the locking screw Do not over tighten the screw 5 Inspectthe charging contacts to ensure they are clean and unobstructed 6 Connect the power supply to the TWC1 You are now ready to charge a battery compatible with the charging pod O Charging A Battery 1 2 3 4 Confirm thatthe charging pod and battery are compatible Connect the small end ofthe power supply cable to the plug on the back of the charger then connectthe AC adaptor to a wall outlet Place battery to be charged in the charging pod The battery may be charged while attached to the radio When a battery is placed in the charging pod the charge status LED will illuminate ORANGE for a short period while the charger performs a battery diagnostic If the LED does not illuminate check to make sure the wall out let is receiving power The charge status LED will change from ORANGE to RED once the battery diagnostic is complete While a battery is charging the charge status LED will illuminate RED with no flashing If the charge status LED is red and flashes a fault has been detected
3. Single Unit Rapid Charger FOR RECHARGEABLE TWO WAY RADIO BATTERIES Model TWC1 Introduction Thank you for purchasing an ENDURA TWC1 Single Unit Rapid Charger This high quality product is designed for charging two way radio batteries With the appropriate charging pod installed it can charge these types of batteries lithium on Li lon lithium polymer LiPo nickel metal hydride NiMH or nickel cadmium NiCd For a complete list of charging pods available for this charger contact your Power Products dealer or call customer service at 800 529 1618 Important 1 Read all Caution statements below and this User Manual before attempt ing to charge a battery 2 Check to make sure a charging pod compatible with your battery is prop erly installed on charger before placing battery in pod 3 Position charger away from TVs radios or other receivers to prevent the charger from interfering with these types of products 4 Always charge new batteries completely before initial use Recycle bat teries when they can no longer be used Do not discard unwanted batter ies in the trash or incinerate Batteries exposed to fire or excessive heat may explode 5 For best battery performance charge NiCd and NiMH batteries when they are fully discharged 0 Caution 1 Never charge alkaline or dry cell batteries with this charger They may burst and cause damage or personal injury 2 Do not charge Li Ion LiPo NiMH or NiC
4. age is complete Check charging pod to confirm compatibility with battery Indicates over current condition caused by battery short circuit Have the battery checked by a qualified technician Do not attempt charging the battery if a short circuit exists Warranty And Service During Warranty The ENDURATM TWC1 is made from high quality materials and designed to provide years of reliable service The following warranty applies Power Products Unlimited Inc PPU warrants this product to be free from defects in workmanship and materials for one year from date of purchase by the end user This warranty applies to the original purchaser and is void ifthe product has been altered misused damaged neglected or if repair is required because of normal wear and tear This is the only warranty made by PPU In no event will PPU its affiliates subsidiaries related entities or their respective directors officers or employees be liable for any damages beyond repair or replacement as described above including without limita tion indirect incidental or consequential damages For service under war ranty return the product along with dated proof of purchase to the retailer where purchased or to Power Products If returning directly to Power Prod ucts follow these instructions 1 Send to Power Products Warranty Service Department 2170 Brandon Trail Alpharetta GA 30004 For your protection we recommend you ob tain proof of delive
5. d batteries unless they are de signed with overcharge protection 3 Use charger indoors only Do not expose the charger to rain any liquids or excessive moisture 4 Do not attempt to charge a battery without first installing the appropriate charging pod Use only charging pods designed for the ENDURATM TWC1 charger Disconnect charger from power supply before installing adjust ing or removing the charging pod 5 Make sure contacts in charging pod and battery are clean Do not allow wire or metal objects to touch contacts in charging pod or any internal part of the charger 6 Do not remove the charger s housing or make any modification to the charger 7 Use only the power supply provided with the ENDURA TWC1 charger If a replacement power supply is required order part number TWC1 PS Use of other power supplies may damage the charger or batteries you may be attempting to charge ENDURA TWC1 Features 1 Power supply 2 TWC1 single unit rapid charger 3 Removable charging pod 4 Charge status LED Note Quick reference informa tion for charge status LED is located on bottom of charger Replacing A Charging Pod The charging pod is made from quality materials and designed to provide years of service when properly used In most cases the charging pod will only be replaced when you wantto use the charger with a different battery Follow these steps to change the charging pod 1 Obtain a charging pod made
6. ry for your shipment 2 Include with your product dated proof of purchase your name and day time telephone number and return address street address only return shipments cannot be made to a P O Box 3 All items sent become the property of Power Products and will not be returned ENDURA TWC1 Specifications Dimensions 115 x 136 x 66 mm 4 5 x 5 4 x 2 6 inches Weight Charger Only 275g 6lbs Compatible Chemistries NiCd NiMH Li Ion LiPo Operating Temperature 15 C 30 C 59 F 86 F Storage Temperature 0 C 65 C 32 F 149 C Power Supply Input 100V 240V AC 50 Hz 60 Hz 0 5A Power Supply Output 15V DC 1 0A Charge Rate 700 mA 10 6V 13 5V Specifications subject to change without notice PowerProducts ENDURA Chargers By Power Products 2170 Brandon Trail Alpharetta GA 30004 Smart Adaptable Reliable www powerproducts com O 2012 Power Products Unlimited Inc Power Products is a registered trademark of Power Products Unlimited Inc ENDURA is a trademark of HT Mobile Products Inc All rights reserved
Download Pdf Manuals
Related Search