Modelspace 1:16 scale Mitsubishi A6M2b Zero Propeller + Engine
Contents
1. LR44 batteries included remote control for approximately 5 minutes e Operate by pointing the remote control s infrared LED at the propeller Always switch it off when not in use 1 To start gently press the Start Stop switch 2 You will hear the sounds of the inertia starter rotating for approximately 3 seconds then idling for approximately 15 seconds then low power for approximately 16 seconds then high power The propeller rotation speed will also change at each stage 3 To stop gently press the Start Stop switch once It takes approximately 23 seconds for it to stop completely after you have pressed the switch Pressing it several times in succession will cause a malfunction Infrared LED e The remote control s range is up to one metre from the front of the propeller If the batteries are depleted operations may stop halfway through in order to prevent a malfunction In such situations you should replace all the batteries in the main unit with new ones Start Stop When you press this button if off it will start up and if running it will begin the stopping process e Volume up If you press this button the volume will increase by one step Once the engine volume reaches its Volume down If you press this button the volume will decrease by one step The engine volume cannot decrease further than its maximum level it cannot increase further minimum level it will never become2. the cables will need to be glued directly into the holes drilled in Step 2 For details see Stage 50 Steps 16 18 23 28 When preparing the spark plug cables to fit into the electrode tube first glue two pieces of spark plug cables together as shown in the diagram on the right Then glue them into the holes in the electrode tube projections that were drilled in Step 4 The rear cylinders only have a front half so the spark plug cables should be glued into the holes drilled in Step 3 Glue the first 2mm together Leave a gap of around 1mm Bend inwards For details see along this Stage 97 Steps 1 16 line Cowl Flap parts A though used in the Step by Step build will not be used here Assemble the cowl flaps as in Stage 97 and fix onto the projections circling the model These parts are movable so should not be glued After fixing onto one of the projections Glue here To glue Cowl Flap part H onto the model as in Step 16 of the Step by Step instructions bend them at the line shown above then glue Projection the bent parts to the model over the exhaust outlets Applying decals to the propeller and engine Decal no 9 x 2 direction of propeller rotation Say For details see Stage 99 Steps 20 26 Decal no 10 x 2 direction aN of propeller rotation OCs eA y Before applying any decals you may want to have a decal softene
3. totally silent Precautions e Operate this device in accordance with the user manual e This is precision machinery and should not be disassembled modified or handled roughly Be careful when using it near other machines with infrared receivers as there is a risk of malfunction Do not place your fingers face hair etc near the revolving blades Do not deliberately lock the revolving blade part Do not store or use in places subject to high temperature high humidity or direct sunlight such as inside vehicles Do not use if broken Set the batteries plus and minus orientations correctly and remove the batteries if not using for a long time Do not use a mixture of batteries of different brands or types Do not use a mixture of old and new batteries e Do not use rechargeable batteries To avoid depleting the batteries always switch off after use Remove any depleted batteries promptly If the product does not work correctly try changing the batteries Unsuitable for those aged under 12 Keep away from children Be careful that the small parts do not get swallowed Use and store out of the reach of children under 3 De Agostini Uk Ltd Battersea Studios 2 82 Silverthorne Road London SW8 3HE UK
4. Modelspace 1 16 scale Mitsubishi AGM2b Zero Propeller Engine Sound System Painting manual If you intend to paint the model please read this manual before assembling it Gear chamber Gilinderhesd Painting the main body Use paints designed for plastic models Crankcase Cylinder head Burnt iron Exhaust pipes Electrode tube ahtare Crankcase gm grey Gear chamber Main body 1 Main body 1 e eck Main body 2 Main body 2 Exhaust pipes Front Painting the propeller Refer to Stage 56 Steps 9 10 for how to paint the propeller Propeller blades Silver Spinner Spinner cover Propeller front Semi gloss black Propeller back Cowl flaps Cowl flap hinges Painting the cowl flaps cowl flap hinges Spinner Spinner cover See Stage 97 Steps 1 2 Caution Do NOT paint the six areas shown below as they may stop functioning normally if paint sticks to them If you paint the gaps between the parts paint may enter the machinery and cause a malfunction e Apply masking tape to the parts shown below before painting If paint enters the battery contacts there is a risk of it being impossible to switch on the power e If paint covers the infrared receiver there is a risk that the remote control won t be able to connect to it Power switch Inside of battery case Infrared receiver Assembly guide Prepare the spark plugs Your parts Spark plugs x14 C
5. owl flap hinges x 4 Erda To prepare the spark plugs you should refer to the or qaetalis see Stage 13 Steps 10 18 Step by Step instructions in Stage 13 Spark plug cable Drill holes to fit the spark plugs Drill holes for the spark plug cables 1 Use a drill to make holes 1mm in diameter and 1 5mm deep in the circular depressions of all 14 cylinders shown in the centre of the inset below left Drill a hole into the rear side of the forward cylinders indicated by the arrows the rough spot before drilling Use a drill to make holes 0 7mm in diameter and 1 5mm deep in the base of the model at the back of the rear cylinders arrows Use a pin or similar to mark Drill holes at roughly this Leaveagapot erem roune cylinders from the edge For details see Stage 13 Steps 19 21 Drill holes for the spark plug cables 2 Attach the plugs to the cylinder head Use a drill to make holes 0 7mm in diameter and 1 5mm deep in the centre of Fit the spark plugs into the 14 holes drilled in Step 2 each of the projections on the electrode tube Use a pin or similar to mark the rough spot before drilling as in Step 3 For details see Stage 13 Steps 22 25 Electrode tube Projection _ Z i i Projection centre Afterihepiugs Q have been inserted Preparing and fitting the spark plug cables As the cylinders don t have holes in the back of them as they do on the metal engine
6. r and setter to hand to help you Decals 9 and 10 come in red and black versions one each Choose which one you want to stick on Decal no 20 x 4 one is a spare Decal no 21 Decal no 5 x 3 Attaching the propeller to the motor shaft How to attach the engine Insert the motor shaft firmly into the propeller hole as far as it will go Remove the metal engine currently attached to the aircraft body along with the lubricating oil tank Next push the hooks of this engine through the holes of the firewall and hook it into place Propeller hole Caution If it is not inserted fully the propeller may come loose during operation and cause a serious accident Attach the cowling before attaching the propeller Motor shaft User manual Detach the engine from the model and attach the engine sound system then you can use the remote control to enjoy a powerful engine sound matching the propeller speed e Start by inserting batteries three AAA into the main unit Place them in the battery box checking the markings to ensure their orientation is correct then switch on the main unit and the remote OW Z Ox Switch on the main unit by moving the main unit s power switch to Switch on the remote control by the power switch on the right side of the ON position the remote control to the ON position It will shut off automatically if no instructions are received from the This runs on two
Download Pdf Manuals
Related Search